A Discrete Numerical Study of the Effect of the Thickness and the Porosity of the Sand Cushion on the Impact Response Due to the Rockfall

The prevention and the reduction of the rockfall are the common measures of the prevention and the reduction of disasters.When the rock-shed resists the impact of the rockfall,the force that acts on the structure consists of the cushion dead load and the impact-induced load,of which the dynamic process of the propagation of the impactinduced load is complex.Therefore,we conducted a numerical study to investigate the impact of the rockfall.Considering the highly discrete characteristic of the sand,we developed a numerical model on the basis of the discrete element method(DEM).The numerical model,which simulation results were validated by the results of real-scale experiments,was used to investigate the dynamic response of the impact force of the rockfall and the transmission of the impact force under the different magnitude of the falling height and the different thickness of the sand cushion.The results of our study indicated that the cushion thickness had little effect on the impact of the rockfall,and the dense sand cushion generated higher impact force than did the loose sand cushion.Although the high thickness enhanced the buffer performance of the sand cushion,the additional force induced by the dead load of sand cushion was significant.Therefore,to determine the appropriate thickness of the sand cushion,we suggested designers consider the buffer performance and the dead load of the sand cushion.The analysis presented in this paper provided a practical estimation of the impact-induced force of the thick sand cushion.

Evaluation of retinal and choroidal thickness changes in overweight and obese adults without ocular symptoms by swept-source optical coherence tomography

AIM:To evaluate the relationship of overweight and obesity with retinal and choroidal thickness in adults without ocular symptoms by swept-source optical coherence tomography(SS-OCT).METHODS:According to the body mass index(BMI)results,the adults enrolled in the cross-sectional study were divided into the normal group(18.50≤BMI<25.00 kg/m^(2)),the overweight group(25.00≤BMI<30.00 kg/m^(2)),and the obesity group(BMI≥30.00 kg/m^(2)).The one-way ANOVA and the Chi-square test were used for comparisons.Pearson’s correlation analysis was used to evaluate the relationships between the measured variables.RESULTS:This research covered the left eyes of 3 groups of 434 age-and sex-matched subjects each:normal,overweight,and obesity.The mean BMI was 22.20±1.67,26.82±1.38,and 32.21±2.35 kg/m^(2) in normal,overweight and obesity groups,respectively.The choroid was significantly thinner in both the overweight and obesity groups compared to the normal group(P<0.05 for all),while the retinal thickness of the three groups did not differ significantly.Pearson’s correlation analysis showed that BMI was significantly negatively correlated with choroidal thickness,but no significant correlation was observed between BMI and retinal thickness.CONCLUSION:Choroidal thickness is decreased in people with overweight or obesity.Research on changes in choroidal thickness contributes to the understanding of the mechanisms of certain ocular disorders in overweight and obese adults.

Non-linear relationship between age and subfoveal choroidal thickness in Chinese patients with proliferative diabetic retinopathy

BACKGROUND No study has investigated the change regularity between age and subfoveal choroidal thickness(SFCT)in proliferative diabetic retinopathy(PDR).AIM To investigate the relationship between the SFCT and age in Chinese patients with PDR.METHODS This was a cross-sectional retrospective study.The participants were hospitalized individuals with type 2 diabetes who underwent vitrectomy for PDR.Contralateral eyes that met the criteria were included in the study.All necessary laboratory tests were performed at the time of admission.Central macular thickness(CMT)and SFCT were two quantitative assessments made using enhanced depth imaging optical coherence tomography.CMT was measured automatically and SFCT was measured manually with digital calipers provided by the Heidelberg Eye Explorer software.RESULTS The final analysis included a total of 234 individuals with PDR.The average age was 55.60 years old±10.03 years old,and 57.69%of the population was male.Univariate analysis revealed a significant negative connection between age and SFCT in patients with PDR[β=-2.44,95%confidence interval(95%CI):-3.46 to-1.42;P<0.0001].In the fully adjusted model,the correlation between SFCT and age remained steady(β=-1.68,95%CI:-2.97 to-0.39;P=0.0117).Spline smoothing showed that the relationship between SFCT and age in patients with PDR was non-linear,with an inflection point at 54 years of age.CONCLUSION Our findings suggest that age is a key determinant of choroidal thickness.The non-linear link between SFCT and age in PDR patients should be taken into account.

Design and application of thickness measurement calibration system based on laser displacement sensor

This study aims to improve the accuracy and safety of steel plate thickness calibration.A differential noncontact thickness measurement calibration system based on laser displacement sensors was designed to address the problems of low precision of traditional contact thickness gauges and radiation risks of radiation-based thickness gauges.First,the measurement method and measurement structure of the thickness calibration system were introduced.Then,the hardware circuit of the thickness system was established based on the STM32 core chip.Finally,the system software was designed to implement system control to filter algorithms and human-computer interaction.Experiments have proven the excellent performance of the differential noncontact thickness measurement calibration system based on laser displacement sensors,which not only considerably improves measurement accuracy but also effectively reduces safety risks during the measurement process.The system offers guiding significance and application value in the field of steel plate production and processing.

Electron G-Factor Anomaly and the Charge Thickness

The electron g-factor relates the magnetic moment to the spin angular momentum. It was originally theoretically calculated to have a value of exactly 2. Experiments yielded a value of 2 plus a very small fraction, referred to as the g-factor anomaly. This anomaly has been calculated theoretically as a power series of the fine structure constant. This document shows that the anomaly is the result of the electron charge thickness. If the thickness were to be zero, g = 2 exactly, and there would be no anomaly. As the thickness increases, the anomaly increases. An equation relating the g-factor and the surface charge thickness is presented. The thickness is calculated to be 0.23% of the electron radius. The cause of the anomaly is very clear, but why is the charge thickness greater than zero? Using the model of the interior structure of the electron previously proposed by the author, it is shown that the non-zero thickness, and thus the g-factor anomaly, are due to the proposed positive charge at the electron center and compressibility of the electron material. The author’s previous publication proposes a theory for splitting the electron into three equal charges when subjected to a strong external magnetic field. That theory is revised in this document, and the result is an error reduced to 0.4% in the polar angle where the splits occur and a reduced magnetic field required to cause the splits.

Correlation Study of Aortic Velocity Propagation, Abdominal Aortic Intima-Media Thickness, and Epicardial Adipose Tissue Thickness in Subclinical Hypothyroidism Patients

Objective:To explore the correlation between epicardial fat thickness(EFT),aortic velocity propagation(AVP),and abdominal aortic intima-media thickness(AA-IMT)in patients with subclinical hypothyroidism(SH).Additionally,to compare these indicators between SH patients and healthy individuals,providing a new theoretical basis for the clinical prevention and treatment of cardiovascular diseases.Method:Clinical data from 50 SH patients(23 males and 27 females)and 50 healthy outpatient examinees(22 males and 28 females)were analyzed.The participants were selected from January 2022 to December 2023 at Loudi Central Hospital.EFT,AVP,and AA-IMT were measured,and their correlations were analyzed.Results:SH patients had significantly higher EFT and AA-IMT levels than the control group,while their AVP was significantly lower,with these differences being statistically significant(P<0.05).Correlation analysis revealed a significant negative correlation between EFT and AVP(P<0.001),a significant positive correlation between EFT and AAO-IMT(P<0.001),and a significant negative correlation between AVP and AAO-IMT(P<0.001).Multivariate binary logistic regression analysis identified increased EFT,decreased AVP,and increased AAO-IMT as independent risk factors for SH patients.Conclusion:In SH patients,EFT and AAO-IMT are elevated,whereas AVP is reduced.EFT and AVP are significantly correlated with AAO-IMT.EFT and AAO-IMT can serve as reliable indicators for evaluating subclinical atherosclerosis in SH patients,providing a diagnostic basis for clinical practice.

Influence of layer thickness on formation quality,microstructure,mechanical properties,and corrosion resistance of WE43 magnesium alloy fabricated by laser powder bed fusion

Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not been studied for Mg alloys.In this study,WE43 Mg alloy bulk cubes,porous scaffolds,and thin walls with layer thicknesses of 10,20,30,and 40μm were fabricated.The required laser energy input increased with increasing layer thickness and was different for the bulk cubes and porous scaffolds.Porosity tended to occur at the connection joints in porous scaffolds for LT40 and could be eliminated by reducing the laser energy input.For thin wall parts,a large overhang angle or a small wall thickness resulted in porosity when a large layer thicknesses was used,and the porosity disappeared by reducing the layer thickness or laser energy input.A deeper keyhole penetration was found in all occasions with porosity,explaining the influence of layer thickness,geometrical structure,and laser energy input on the porosity.All the samples achieved a high fusion quality with a relative density of over 99.5%using the optimized laser energy input.The increased layer thickness resulted to more precipitation phases,finer grain sizes and decreased grain texture.With the similar high fusion quality,the tensile strength and elongation of bulk samples were significantly improved from 257 MPa and 1.41%with the 10μm layer to 287 MPa and 15.12%with the 40μm layer,in accordance with the microstructural change.The effect of layer thickness on the compressive properties of porous scaffolds was limited.However,the corrosion rate of bulk samples accelerated with increasing the layer thickness,mainly attributed to the increased number of precipitation phases.

Using choroidal thickness to detect myopic macular degeneration

AIM:To explore the usage of choroidal thickness measured by swept-source optical coherence tomography(SS-OCT)to detect myopic macular degeneration(MMD)in high myopic participants.METHODS:Participants with bilateral high myopia(≤−6 diopters)were recruited from a subset of the Guangzhou Zhongshan Ophthalmic Center-Brien Holden Vision Institute High Myopia Cohort Study.SS-OCT was performed to determine the choroidal thickness,and myopic maculopathy was graded by the International Meta-Analysis for Pathologic Myopia(META-PM)Classification.Presence of MMD was defined as META-PM category 2 or above.RESULTS:A total of 568 right eyes were included for analysis.Eyes with MMD(n=106,18.7%)were found to have older age,longer axial lengths(AL),higher myopic spherical equivalents(SE),and reduced choroidal thickness in each Early Treatment Diabetic Retinopathy Study(ETDRS)grid sector(P<0.001).The area under the receiver operating characteristic(ROC)curves(AUC)for subfoveal choroidal thickness(0.907)was greater than that of the model,including age,AL,and SE at 0.6249,0.8208,and 0.8205,respectively.The choroidal thickness of the inner and outer nasal sectors was the most accurate indicator of MMD(AUC of 0.928 and 0.923,respectively).An outer nasal sector choroidal thickness of less than 74μm demonstrated the highest odds of predicting MMD(OR=33.8).CONCLUSION:Choroidal thickness detects the presence of MMD with high agreement,particularly of the inner and outer nasal sectors of the posterior pole,which appears to be a biometric parameter more precise than age,AL,or SE.

Pipeline thickness estimation using the dispersion of higher-order SH guided waves

Thickness measurement plays an important role in the monitoring of pipeline corrosion damage. However, the requirement for prior knowledge of the shear wave velocity in the pipeline material for popular ultrasonic thickness measurement limits its widespread application. This paper proposes a method that utilizes cylindrical shear horizontal(SH) guided waves to estimate pipeline thickness without prior knowledge of shear wave velocity. The inversion formulas are derived from the dispersion of higher-order modes with the high-frequency approximation. The waveform of the example problems is simulated using the real-axis integral method. The data points on the dispersion curves are processed in the frequency domain using the wave-number method. These extracted data are then substituted into the derived formulas. The results verify that employing higher-order SH guided waves for the evaluation of thickness and shear wave velocity yields less than1% error. This method can be applied to both metallic and non-metallic pipelines, thus opening new possibilities for health monitoring of pipeline structures.

Assessments of Data-Driven Deep Learning Models on One-Month Predictions of Pan-Arctic Sea Ice Thickness

In recent years,deep learning methods have gradually been applied to prediction tasks related to Arctic sea ice concentration,but relatively little research has been conducted for larger spatial and temporal scales,mainly due to the limited time coverage of observations and reanalysis data.Meanwhile,deep learning predictions of sea ice thickness(SIT)have yet to receive ample attention.In this study,two data-driven deep learning(DL)models are built based on the ConvLSTM and fully convolutional U-net(FC-Unet)algorithms and trained using CMIP6 historical simulations for transfer learning and fine-tuned using reanalysis/observations.These models enable monthly predictions of Arctic SIT without considering the complex physical processes involved.Through comprehensive assessments of prediction skills by season and region,the results suggest that using a broader set of CMIP6 data for transfer learning,as well as incorporating multiple climate variables as predictors,contribute to better prediction results,although both DL models can effectively predict the spatiotemporal features of SIT anomalies.Regarding the predicted SIT anomalies of the FC-Unet model,the spatial correlations with reanalysis reach an average level of 89%over all months,while the temporal anomaly correlation coefficients are close to unity in most cases.The models also demonstrate robust performances in predicting SIT and SIE during extreme events.The effectiveness and reliability of the proposed deep transfer learning models in predicting Arctic SIT can facilitate more accurate pan-Arctic predictions,aiding climate change research and real-time business applications.

Tailoring MXene Thickness and Functionalization for Enhanced Room‑Temperature Trace NO_(2) Sensing

In this study,precise control over the thickness and termination of Ti3C2TX MXene flakes is achieved to enhance their electrical properties,environmental stability,and gas-sensing performance.Utilizing a hybrid method involving high-pressure processing,stirring,and immiscible solutions,sub-100 nm MXene flake thickness is achieved within the MXene film on the Si-wafer.Functionalization control is achieved by defunctionalizing MXene at 650℃ under vacuum and H2 gas in a CVD furnace,followed by refunctionalization with iodine and bromine vaporization from a bubbler attached to the CVD.Notably,the introduction of iodine,which has a larger atomic size,lower electronegativity,reduce shielding effect,and lower hydrophilicity(contact angle:99°),profoundly affecting MXene.It improves the surface area(36.2 cm^(2) g^(-1)),oxidation stability in aqueous/ambient environments(21 days/80 days),and film conductivity(749 S m^(-1)).Additionally,it significantly enhances the gas-sensing performance,including the sensitivity(0.1119Ωppm^(-1)),response(0.2% and 23%to 50 ppb and 200 ppm NO_(2)),and response/recovery times(90/100 s).The reduced shielding effect of the–I-terminals and the metallic characteristics of MXene enhance the selectivity of I-MXene toward NO2.This approach paves the way for the development of stable and high-performance gas-sensing two-dimensional materials with promising prospects for future studies.

Three-dimensional choroidal vascularity index and choroidal thickness in fellow eyes of acute and chronic primary angle-closure using swept-source optical coherence tomography

AIM:To compare the three-dimensional choroidal vascularity index(CVI)and choroidal thickness between fellow eyes of acute primary angle-closure(F-APAC)and chronic primary angle-closure glaucoma(F-CPACG)and the eyes of normal controls.METHODS:This study included 37 patients with unilateral APAC,37 with asymmetric CPACG without prior treatment,and 36 healthy participants.Using swept-source optical coherence tomography(SS-OCT),the macular and peripapillary choroidal thickness and three-dimensional CVI were measured and compared globally and sectorally.Pearson’s correlation analysis and multivariate regression models were used to evaluate choroidal thickness or CVI with related factors.RESULTS:The mean subfoveal CVIs were 0.35±0.10,0.33±0.09,and 0.29±0.04,and the mean subfoveal choroidal thickness were 315.62±52.92,306.22±59.29,and 262.69±45.55μm in the F-APAC,F-CPACG,and normal groups,respectively.All macular sectors showed significantly higher CVIs and choroidal thickness in the F-APAC and F-CPACG eyes than in the normal eyes(P<0.05),while there were no significant differences between the F-APAC and F-CPACG eyes.In the peripapillary region,the mean overall CVIs were 0.21±0.08,0.20±0.08,and 0.19±0.05,and the mean overall choroidal thickness were 180.45±54.18,174.82±50.67,and 176.18±37.94μm in the F-APAC,F-CPACG,and normal groups,respectively.There were no significant differences between any of the two groups in all peripapillary sectors.Younger age,shorter axial length,and the F-APAC or F-CPACG diagnosis were significantly associated with higher subfoveal CVI and thicker subfoveal choroidal thickness(P<0.05).CONCLUSION:The fellow eyes of unilateral APAC or asymmetric CPACG have higher macular CVI and choroidal thickness than those of the normal controls.Neither CVI nor choroidal thickness can distinguish between eyes predisposed to APAC or CPACG.A thicker choroid with a higher vascular volume may play a role in the pathogenesis of primary angle-closure glaucoma.

A Formulation of the Porous Medium Equation with Time-Dependent Porosity: A Priori Estimates and Regularity Results

We consider a generalized form of the porous medium equation where the porosity ϕis a function of time t: ϕ=ϕ(x,t): ∂(ϕS)∂t−∇⋅(k(S)∇S)=Q(S).In many works, the porosity ϕis either assumed to be independent of (or to depend very little of) the time variable t. In this work, we want to study the case where it does depend on t(and xas well). For this purpose, we make a change of unknown function V=ϕSin order to obtain a saturation-like (advection-diffusion) equation. A priori estimates and regularity results are established for the new equation based in part on what is known from the saturation equation, when ϕis independent of the time t. These results are then extended to the full saturation equation with time-dependent porosity ϕ=ϕ(x,t). In this analysis, we make explicitly the dependence of the various constants in the estimates on the porosity ϕby the introduced transport vector w, through the change of unknown function. Also we do not assume zero-flux boundary, but we carry the analysis for the case Q≡0.

Diagenetic history and porosity evolution of the Middle Permian clastic-carbonate mixed system,Indus Basin,Pakistan:Implications for reservoir development

This study deals with unraveling the diagenesis-induced porosity evolution in a mixed clastic-carbonate sequence of the Middle Permian Indus Basin,Pakistan.Multiple data sets including outcrop,petrography,cathodoluminescence,scanning electron microscopy(SEM),mineralogy,and geochemical isotopic compositions were integrated to establish a link between porosity evolution and diagenesis.The spatial thickness and facies variations of the strata at outcrop scale are inherently controlled by the underlying bathymetry of the basin with deepening westward trend.The low values ofδ^(18)O of the target strata,relative to average values of the Permian carbonate,hints to diagenetic alteration in the strata.The data sets used in this study reveal modification of the strata in four environments,that is,i)early marine diagenesis indicated by micritization,pervasive dolomitization and isopachous fibrous cements,followed by ii)meteoric dissolution,and iii)shallow burial diagenetic processes including the precipitation of blocky cement,compaction of skeletal and non-skeletal allochems,and stylolites,and iv)a deep burial environment,characterized by pressure solution,and micro-fractures.The clastic intervals host subangular to subrounded quartz grains,floating textures,and almost complete absence of deleterious clay minerals,consequently resulting in the preservation of primary porosity.The primary porosity of carbonate intervals is preserved in the form of intercrystalline and intracrystalline porosity.The secondary porosity evolved through various diagenetic phases in the form of fractures and dissolution.The diagenetic solution mediated by organic matter in carbonates may have experienced both bacterial decomposition and thermochemical sulfate reduction,precipitating sulfides within the pores.The plug porosity/permeability analyses generally suggest high porosity in the siliciclastic unit,and carbonates with wackestone fabric while lower values were observed for the inner shelf pure carbonate facies.However,both intervals show very low permeability values probably due to isolated moldic pores and intense micritization.Therefore,clastic intervals may provide an opportunity to serve as a moderate reservoir;however,the carbonate intervals possess very low permeability values and could generally be considered as low-moderate reservoir potential.

Determining the effective elastic thickness through cross-correlation between isostatic disturbances

The elastic thickness parameter was estimated using the mobile correlation technique between the observed isostatic disturbance and the gravity disturbance calculated through direct gravimetric modeling. We computed the vertical flexure value of the crust for a specific elastic thickness using a given topographic dataset. The gravity disturbance due to the topography was determined after the calculation. A grid of values for the elastic thickness parameter was generated. Then, a moving correlation was performed between the observed gravity data(representing actual surface data) and the calculated data from the forward modeling. The optimum elastic thickness of the particular point corresponded to the highest correlation coefficient. The methodology was tested on synthetic data and showed that the synthetic depth closely matched the original depth, including the elastic thickness value. To validate the results, the described procedure was applied to a real dataset from the Barreirinhas Basin, situated in the northeastern region of Brazil. The results show that the obtained crustal depth is highly correlated with the depth from known models. Additionally, we noted that the elastic thickness behaves as expected, decreasing from the continent towards the ocean. Based on the results, this method has the potential to be employed as a direct estimate of crustal depth and elastic thickness for any region.

Stochastic seismic inversion and Bayesian facies classification applied to porosity modeling and igneous rock identification

We apply stochastic seismic inversion and Bayesian facies classification for porosity modeling and igneous rock identification in the presalt interval of the Santos Basin. This integration of seismic and well-derived information enhances reservoir characterization. Stochastic inversion and Bayesian classification are powerful tools because they permit addressing the uncertainties in the model. We used the ES-MDA algorithm to achieve the realizations equivalent to the percentiles P10, P50, and P90 of acoustic impedance, a novel method for acoustic inversion in presalt. The facies were divided into five: reservoir 1,reservoir 2, tight carbonates, clayey rocks, and igneous rocks. To deal with the overlaps in acoustic impedance values of facies, we included geological information using a priori probability, indicating that structural highs are reservoir-dominated. To illustrate our approach, we conducted porosity modeling using facies-related rock-physics models for rock-physics inversion in an area with a well drilled in a coquina bank and evaluated the thickness and extension of an igneous intrusion near the carbonate-salt interface. The modeled porosity and the classified seismic facies are in good agreement with the ones observed in the wells. Notably, the coquinas bank presents an improvement in the porosity towards the top. The a priori probability model was crucial for limiting the clayey rocks to the structural lows. In Well B, the hit rate of the igneous rock in the three scenarios is higher than 60%, showing an excellent thickness-prediction capability.

Isotopic dependence of the yield ratios of light fragments from different projectiles and their unified neutron skin thicknesses

The yield ratios of neutron-proton(R(n/p))and^(3)H-^(3)He(R(^(3)H∕^(3)He))with reduced rapidity from 0 to 0.5 were simulated at 50 MeV/u even-even ^(36−56)Ca+^(40)Ca,even-even ^(48−78)Ni+^(58)Ni,and ^(100−139)Sn(every third isotopes)+112 Sn for full reduced impact parameters using the isospin-dependent quantum molecular dynamics(IQMD)model.The neutron and proton density distributions and root-mean-square radii of the reaction systems were obtained using the Skyrme-Hartree-Fock model,which was used for the phase space initialization of the projectile and target in IQMD.We defined the unified neutron skin thickness asΔRnp=<r^(2)>^(1∕2) n−<r^(2)>^(1∕2)p,which was negative for neutron-deficient nuclei.The unifiedΔRnp values for nuclei with the same relative neutron excess from different isotopic chains were nearly equal,except for extreme neutron-rich isotopes,which is a type of scaling behavior.The yield ratios of the three isotopic chain-induced reactions,which depended on the reduced impact parameter and unified neutron skin thickness,were studied.The results showed that both R(n/p)and R(^(3)H∕^(3)He)decreased with a reduced impact parameter for extreme neutron-deficient isotopes;however,they increased with reduced impact parameters for extreme neutron-rich isotopes,and increased with theΔRnp of the projectiles for all reduced impact parameters.In addition,a scaling phenomenon was observed betweenΔR np and the yield ratios in peripheral colli-sions from different isotopic chain projectiles(except for extreme neutron-rich isotopes).Thus,R(n/p)and R(^(3)H∕^(3)He)from peripheral collisions were suggested as experimental probes for extracting the neutron or proton skin thicknesses of non-extreme neutron-rich nuclei from different isotopic chains.

A study on the temperature sensitivity of NMR porosity in porous media based on the intensity of magnetization Dedicated to the special issue “Magnetic Resonance in Porous Media”

The measurement of nuclear magnetic resonance(NMR)porosity is affected by temperature.Without considering the impact of NMR logging tools,this phenomenon is mainly caused by variations in magnetization intensity of the measured system due to temperature fluctuations and difference between the temperature of the porous medium and calibration sample.In this study,the effect of temperature was explained based on the thermodynamic theory,and the rules of NMR porosity responses to temperature changes were identified through core physics experiments.In addition,a method for correcting the influence of temperature on NMR porosity measurement was proposed,and the possible factors that may affect its application were also discussed.

Sandstone Diagenesis and Porosity Evolution of Paleogene in Huimin Depression

The sandstones of the paleogene in the Huimin Depression have undergone numerous diagenetic processes, such as compaction, cementation, dissolution, metasomasis and recrystallization. The first three — compaction, cementation and dissolution — affect reservoir properties most intensively. An average porosity loss due to compaction is 0.78% per 100 meters, slightly higher in the central and southern parts and lower in the northern. Cementation has resulted in the porosity loss from 8% to 20% at a depth below 1,500 meters. Dissolution, which in most cases is the dissolution of feldspar and of carbonate cement, primarily occurs in two depth intervals, from 1,400 to 2,500 meters and 2,700 to 4,000 meters respectively. New porosity is created through dissolution from 4% to 14%. The sandstones experienced stage A and stage B of early diagenesis and stage A of late diagenesis. At present, most of them are experiencing Phase A2 of late diagenesis. The types of pores in the sand reservoir can be grouped into primary and secondary ones.

Preparation and Characterization of Activated Carbons from Palm Nut Shells: Effects of Calcination Temperature on Porosity and Chemical Properties

Activated carbons (ACs) calcined at 400˚C, 500˚C, and 600˚C (AC-400, AC-500, and AC-600) were prepared using palm nut shells from Gabon as raw material and zinc chloride (ZnCl2) as a chemical activating agent. Prepared ACs were characterized by physisorption of nitrogen (N2), determination of diode and methylene blue numbers for studies of porosity and by quantification and determination of surface functional groups and pH at point of zero charge (pHpzc) respectively, for studies of chemical properties of prepared ACs. Then, effects of calcination temperature (Tcal) on porosity and chemical properties of prepared ACs were studied. The results obtained showed that when the calcination temperature increases from 500˚C to 600˚C, the porosity and chemical properties of prepared ACs are modified. Indeed, the methylene blue and iodine numbers determined for activated carbons AC-400 (460 and 7.94 mg·g−1, respectively) and AC-500 (680 and 8.90 mg·g−1, respectively) are higher than those obtained for AC-600 (360 and 5.75 mg·g−1, respectively). Compared to the AC-500 adsorbent, specific surface areas (SBET) and microporous volume losses for AC-600 were estimated to 44.7% and 45.8%, respectively. Moreover, in our experimental conditions, the effect of Tcal on the quantities of acidic and basic functional groups on the surface of the ACs appears negligible. In addition, results of the pHpzc of prepared ACs showed that as Tcal increases, the pH of the adsorbents increases and tends towards neutrality. Indeed, a stronger acidity was determined on AC-400 (pHpzc = 5.60) compared to those on AC-500 and AC-600 (pHpzc = 6.85 and 6.70, respectively). Also according to the results of porosity and chemical characterizations, adsorption being a surface phenomenon, 500˚C appears to be the optimal calcination temperature for the preparation of activated carbons from palm nut shells in our experimental conditions.