Photoluminescence and Optical Transition Dynamics of Er^(3+) Ions in Porous Si

Er was doped into porous Si by immersing the porous Si sample in a saturated ErCl3,ethanol solution. Sharp and intense 1.54 μm photoluminescence caused by intra-4f-shefl transitions in Er3+ ions was observed up to room temperature. It is shown that the immersing process is valid to dope Er in high concentration in porous Si. Time resolved study of the Er-doped porous Si revealed that the doped Er3+ ions are excited by energy transfer from photo-generated electron-hole pairs in the host. The energy back transfer process from the excited 4f electrons in the Er3+ion to the host is not a dominant factor to quench the Er-related emission in porous Si. Ourresults are well explained by a proposed model in which an intermediate state was introduced.

Luminescent Properties of Porous Si Passivated by Diamond Film and DLC Film

Surface passivation methods for porous Si (PS) surfaces, i.e., depositing diamond film or diamond-like carbon (DLC) film on PS surfaces, were attempted. Two emission bands, weak blue band and strong red band existed in the PL spectrum of diamond film coated on PS, were discovered by the photoluminescence measurements. The luminescent mechanism and stability were discussed. The results indicated that diamond film may stabilize the PL wavelength and intensity of PS, and therefore could become a promising passivation film of porous Si. The PL properties of PS coated by DLC films, including hydrogenated diamond like carbon (DLC:H) film and nitrogen doped DLC film (DLC:N) were also studied in this paper. The DLC films may stabilize the PL of PS, but the photoluminescent intensity was obviously weaker than that of diamond film coated PS.

Time-Resolved Photoluminescence Spectra of Porous Si

he photoluminescence spectra of porous Si have been studied. Its timere-solved luminescence spectra show a red shift of luminescencc peak with increasingdelay time after exciting and a nonexponential decay. Several spectral bands withdifferent Gaussian center appear by means of the decomposition of a spetrum. Theresuits of our experiments show quantum confined characters in porous Si, and wespeculate that the short wavelength band at 465 nm is the direct band froni P_(15) toP_(25)

Microstructure and brazing mechanism of porous Si_3N_4/Invar joint brazed with Ag-Cu-Ti/Cu/Ag-Cu multi-layered filler

Porous Si3N4 was brazed to Invar alloy in this study, and Ag-Cu-Ti/Cu/Ag-Cu multi-layered filler was designed to inhibit the formation of Fe2Ti and Ni3Ti intermetallic compounds. The effects of the brazing temperature and the thickness of Cu interlayer on the microstructure and mechanical properties of brazed joints were investigated. The typical microstructure of the joint brazed with multi-layered filler was porous Si3N4/TiN ＋ Ti5Si3/Ag-Cu eutectic[Cu[Ag-Cu eutectic/Cu-rich layer ＋ diffusion layer/Invar. When the brazing temperature increased, the reaction layer at the ceramic/filler interface grew thicker and the Cu interlayer turned thinner. As the thickness of Cu interlayer increased from 50 to 150 μm, the joint strength first increased and then decreased. In this research, the maximum shear strength （73 MPa） was obtained when being brazed at 1173 K with a 100 μm Cu interlayer applied in the filler, which was 55% higher than that brazed with single Ag-Cu-Ti brazing alloy and had reached 86% of the ceramic. The release of residual stress and the barrier effect of Cu interlayer to inhibit the formation of Fe2Ti and Ni3Ti intermetallics played the major role in the improvement of joint strength.

Synthesis of carbon nanotubes-supported porous silicon microparticles in low-temperature molten salt for highperformance Li-ion battery anodes

Silicon-based materials has attracted attention as a promising candidate for lithium-ion batteries(LIBs)with high energy density.However,severe volume variation,pulverization,and poor conductivity hindered the development of Si based materials.In this study,porous Si microparticles supported by carbon nanotubes(p-Si/CNT)are fabricated through simple molten salt assisted dealloying process at low temperature followed by acid treatment.The ZnCl2 molten salt not only provides the liquid environment to enhance the reaction,but also participates the dealloying process and works as template for porous structure when removes by acid treatment.Additionally,distribution of defect sites in CNTs also increases after molten salt process.Density function theory(DFT)calculations further prove the defects could improve the adsorption of Li+.The participation of CNTs can also contribute to the reaction kinetics and retain the integrity of the electrode.As expected,the p-Si/CNT anode manifests enhanced lithium-storage performance in terms of superior cycling stability and good rate capability.The p-Si/CNT//LiCoO_(2) full cell assembly further demonstrates its potential as a prospective anode for high-performance LIBs.

Fabrication and Properties of Porous Si_3N_4 Ceramic with High Porosity

A novel process combining oxidation-bonding and sintering was developed to fabricate porous Si3N4 ceramic with high porosity. After sintering at 1800℃, the SiO2 in porous Si3N4 ceramic transforms into Si2N2O because of the reaction of SiO2 and Si3N4 . Due to the reaction of SiO2 and carbon, the porosity of porous Si3N4 ceramic increases obviously from 40.2% to 76.8% with the weight decreasing by 35.6%. As the porosity increases, the dielectric constant and loss of the porous Si3N4 ceramic decrease obviously from 3.08 to 1.61 and from 3.70×10（-3） to 0.74×10（-3） , but due to the production of Si2N2O whose mechanical properties are much higher than SiO2 and the increase of the bonding strength among Si3N4 particles, the flexural strength and the fracture toughness of the porous Si3N4 ceramic decrease from 55 to 39 MPa and from 0.7 to 0.5 MPa·m（1/2） , respectively, but its Vickers hardness increases from 1.2 to 1.3 GPa.

White light photoluminescence from ZnS films on porous Si substrates

ZnS films were deposited on porous Si （PS） substrates using a pulsed laser deposition （PLD） technique. White light emission is observed in photoluminescence （PL） spectra, and the white light is the combination of blue and green emission from ZnS and red emission from PS. The white PL spectra are broad, intense in a visible band ranging from 450 to 700 nrn. The effects of the excitation wavelength, growth temperature of ZnS films, PS porosity and annealing temperature on the PL spectra of ZnS/PS were also investigated.

Preparation and Properties of Si2N2O Ceramics for Microwave Sintering Furnaces

Si2N2O ceramics were prepared using amorphous Si3N4 as the raw material and Li2CO3 as the sintering additive through vacuum multi-stage sintering.The influence of the Li2CO3 addition(0%,1%,2%,3%,and 5%,by mass)on the phase composition,the microstructure,the porosity,the mechanical properties,the dielectric constant and the tangent of the dielectric loss angle of the porous Si2N2O ceramics was investigated.The results reveal that a suitable addition of Li2CO3 can promote the generation of Si2N2O but excessive or inadequate Li2CO3 causes decomposition of Si2N2O ceramics.The prepared porous Si2N2O ceramics have good mechanical properties,good thermal shock resistance,and low dielectric properties,which have excellent potential for application in microwave sintering furnaces.