Influence of Ti Powder Characteristics on Combustion Synthesis of Porous NiTi Alloy

Porous NiTi shape memory alloy (SMA) is a novel biomedical material used for human hard tissue implant. The influence of elemental titanium powder characteristics such as powder morphology, particle size and specific surface area (SSA) on the minimal ignition temperature, combustion temperature and final product of porous NiTi SMA fabricated by combustion synthesis method was investigated in this paper by scanning electron microscopy (SEM) and laser diffraction. The preliminary data indicated that the titanium powder characteristics had a strong effect on combustion synthesis of porous NiTi SMA.

Characteristics of Inconel Powders for Powder-Bed Additive Manufacturing

In this study, the flow characteristics and behaviors of virgin and recycled Inconel powder for powder-bed additive manufacturing （AM） were studied using different powder characterization techniques. The results revealed that the particle size distribution （PSD） for the selective laser melting （SLM） process is typically in the range from 15 μm to 63 μm. The flow rate of virgin Inconel powder is around 28 s·（50 g）^-1. In addition, the packing density was found to be 60%. The rheological test results indicate that the virgin powder has reasonably good flowability compared with the recycled powder. The inter-relation between the powder characteristics is discussed herein. A propeller was successfully printed using the powder. The results suggest that Inconel powder is suitable for AM and can be a good reference for researchers who attempt to pro- duce AM powders.

Characteristics and Microstructure of a Hypereutectic Al-Si Alloy Powder by Ultrasonic Gas Atomization Process

A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.

Fabrication of micro-fine high Nb-containing TiAl alloyed powders by fluidized bed jet milling

A fluidized bed jet milling process was used to make micro-fine high Nb-containing TiAl alloyed powders from the chippings obtained by crushing the Ti-45Al-8.5Nb-(W,B,Y) ingot.The influences of classifier frequency on powder characteristics were investigated.The results show that the powders with controlled average particle size can be prepared on a large scale.The powders with different sizes are all dominated by γ with aminor amount of α2-Ti3Al.The particle size significantly decreases with the classifier frequency increasing.At a classifier frequency higher than 38 Hz,the average particle size of the ground powders is lower than 25μm.The powders are composed of two differ-ent sizes of particles:shaped particles and some clastic particles,and both particle sizes meet the log-normal distribution.With the classifier frequency increasing,the both sizes decrease;meanwhile,the proportion of the clastic particles gradually increases,and the size distribution span value of the ground powders increases correspondingly.

Review on Enhancement of Nitridation of Si Powder

This paper reviewed the effect of powder characteristics and additives including metals,rare earth oxides,and ZrO2 on nitridation of Si powder.The decrease of particle size of Si powder increased nitridation.Most of metal additives inhibited nitridation,while some metal additives such as Fe,Cu,Cr,and Ca increased nitrida—tion.Otherwise,the addition of metals might lead to the degradation of physical and mechanical properties of Si3N4.All the rare earth oxides,especially CeO2 and Eu2O3,showed nitridation enhancing effect.In addition,ZrO2 with small particle size showed a stronger enhancing effect.

Relationship between powder characteristic and internal oxidation of Al in Cu-Al pre-alloyed powders

Since Cu-Al powder characteristics have important effects on the preparation of Cu/Al2O3 composite, the apparent activation energy of Al internal oxidation reaction in Cu-Al pre-alloyed powders with different characteristics was calculated in the present investigation. The microstructure and properties of the synthesized Cu/Al2O3 were studied. The results show that high-energy milling can obviously promote internal oxidation of Al in Cu-Al powders in the same solid solubility. At the same milling conditions and internal oxidation parameters, the solid solution of Al in Cu either in low or high amount will result in the poor microstructure and properties of the Cu/Al2O3 composite. Subsequently, when high-energy milling and internal oxidation are synchronously used to prepare the Cu/Al2O3 composite, there should be an appropriate solubility and milling effect for the pre-alloyed powders.