Optimizing the power conversion processes in diluted donor/acceptor heterojunctions towards 19.4%efficiency all-polymer solar cells

All polymer solar cells(all-PSCs)promise mechanically-flexible and morphologically-stable organic photovoltaics and have aroused increased interests very recently.However,due to their disorderly conformation structures within the photoactive film,inefficient charge generation and carrier transport are observed which lead to inferior photovoltaic performance compared to smaller molecular acceptor-based photovoltaics.Here,by diluting PM6 with a cutting-edge polymeric acceptor PY-IT and diluting PY-IT with PM6 or D18,donor-dominating or acceptor-dominating heterojunctions were prepared.Synchrotron X-ray and multiple spectrometer techniques reveal that the diluted heterojunctions receive increased structural order,translating to enhanced carrier mobility,improved exciton diffusion length,and suppressed non-radiative recombination loss during the power conversion.As the results,the corresponding PM6+1%PY-IT/PY-IT+1%D18 and PM6+1%PY-IT/PY-IT+1%PM6 devices fabricated by layer-by-layer deposition received superior power conversion efficiency(PCE)of 19.4%and 18.8%respectively,along with enhanced operational lifetimes in air,outperforming the PCE of 17.5%in the PM6/PY-IT reference device.

Highly Efficient Power Conversion from Salinity Gradients with Ion-Selective Polymeric Nanopores

A polymeric nanopore membrane with selective ionic transport has been proposed as a potential device to convert the chemical potential energy in salinity gradients to electrical power. However, its energy conversion efficiency and power density are often limited due to the challenge in reliably controlling the size of the nanopores with the conventional chemical etching method. Here we report that without chemical etching, polyimide （PI） membranes irradiated with GeV heavy ions have negatively charged nanopores, showing nearly perfect selectivity for cations over anions, and they can generate electrical power from salinity gradients. We further demonstrate that the power generation efficiency of the PI membrane approaches the theoretical limit, and the maximum power density reaches 130m W/m2 with a modified etching method, outperforming the previous energy conversion device that was made of polymeric nanopore membranes.

Regulation of Power Conversion in Fuel Cells

Here we report a regulation about power conversion in fuel cells. This regulation is expressed as that total power produced by fuel cells is always proportional to the square of the potential difference between the \{equilibrium\} potential and work potential. With this regulation we deduced fuel cell performance equation which can describe the potential vs.the current performance curves, namely, polarization curves of fuel cells with three power source parameters: equilibrium potential E_0; internal resistance R; and power conversion coefficient K. The concept of the power conversion coefficient is a new criterion to evaluate and compare the characteristics and capacity of different fuel cells. The calculated values obtained with this equation agree with practical performance of different types of fuel cells.

Optimal oxide-aperture for improving the power conversion efficiency of VCSEL arrays

The maximum power conversion efficiencies of the top-emitting,oxide-confined,two-dimensional integrated 2×2 and4×4 vertical-cavity surface-emitting laser（VCSEL） arrays with the oxide-apertures of 6 μm,16 μm,19 μm,26 μm,29 μm,36 μm,39 μm,and 46 urn are fabricated and characterized,respectively.The maximum power conversion efficiencies increase rapidly with the augment of oxide-aperture at the beginning and then decrease slowly.A maximum value of27.91%at an oxide-aperture of 18.6 μm is achieved by simulation.The experimental data are well consistent with the simulation results,which are analyzed by utilizing an empirical model.

Study on Purchasing Power Conversion Coefficient at Par

The basic theory of the purchasing power at par refers to the rate of one country＇s currency to U.S. dollar while purchasing ＂a basket＂ goods and services in the same quantity and quality respectively in this country and U.S.A. This paper gives out calculation method of purchasing power conversion coefficient at par and how to calculate the non-base year purchasing power at par.

Ternary organic solar cells offer 14% power conversion efficiency

Organic solar cells （OSCs） have advantages like light-weight, flexibility, colorfulness and solution processability [1 ]. The active layer of OSCs generally contains two organic semiconductors： an electron donor and an electron acceptor. The donor and acceptor make nanoscale phase separation to allow efficient exciton dissociation and also form a three-dimensional （3D） passage to rapidly transfer free charge carriers to respective electrodes.

Effects of Blade Geometry on Performance of Wells Turbine for Wave Power Conversion

An optimum design of the turbine would need a clear understanding of the influence of blade geometry on a Wells turbine performance. Practically, it is difficult to suggest the optimum geometry for the Wells turbine due to the complex interrelation among important parameters, the solidity, hub-to-tip ratio, aspect ratio, blade sweep of rotor, and so on. In the present study, the effect of blade geometry with the hub-to-tip and aspect ratios of rotor on the turbine performance was investigated with a numerical technique. As a result, the optimum blade geometry is as follows: the hub-to-tip ratio is about 0.7, and the aspect ratio about 0.5 under other constant important parameters, NACA0020 blade with blade sweep ratio of 0.35, and solidity of about 0.67. Furthermore, the detailed flow patterns for blade geometry were also shown and discussed in this paper.

Overview of condition monitoring and operation control of electric power conversion systems in direct-drive wind turbines under faults

Electric power conversion system （EPCS）, which consists of a generator and power converter, is one of the most important subsystems in a direct-drive wind turbine （DD-WT）. However, this component accounts for the most failures （approximately 60% of the total number） in the entire DD-WT system according to statistical data. To improve the reliability of EPCSs and reduce the operation and maintenance cost of DD-WTs, numerous researchers have studied condition monitoring （CM） and fault diagnostics （FD）. Numerous CM and FD techniques, which have respective advantages and disadvantages, have emerged. This paper provides an overview of the CM, FD, and operation control of EPCSs in DD-WTs under faults. After introducing the functional principle and structure of EPCS, this survey discusses the common failures in wind generators and power converters; briefly reviewed CM and FD methods and operation control of these generators and power converters under faults; and discussed the grid voltage faults related to EPCSs in DD-WTs. These theories and their related technical concepts are systematically discussed. Finally, predicted development trends are presented. The paper provides a valuable reference for developing service quality evaluation methods and fault operation control systems to achieve high-performance and high-intelligence DD-WTs.

A High Power Conversion Efficiency L-Band Erbium Doped Fiber Amplifier

By using two sections of erbium doped fiber and a fiber optical reflector, a novel, highly efficient L-band amplifier is demonstrated with significantly power-conversion-efficiency enhancement and the gain increasing of as much as 13 dB.

Thermo-electronic solar power conversion with a parabolic concentrator

We consider the energy dynamics of the power generation from the sun when the solar energy is con- centrated on to the emitter ofa thermo-electronic converter with the help of a parabolic mirror. We use the modified Richardson-Dushman equation. The emitter cross section is assumed to be exactly equal to the focused area at a height h from the base of the mirror to prevent loss of efficiency. We report the variation of output power with solar insolation, height h, reflectivity of the mirror, and anode temperature, initially assuming that there is no space charge effect. Our methodology allows us to predict the temperature at which the anode must be cooled in order to prevent loss of efficiency of power conversion. Novel ways of tackling the space charge problem have been discussed. The space charge effect is modeled through the introduction of a parameter f （0 〈 f 〈 1） in the thermos-electron emission equation. We find that the efficiency of the power conversion depends on solar insolation, height h, apart from radii R of the concentrator aperture and emitter, and the collector material properties. We have also considered solar thermos electronic power conversion by using single atom-layer graphene as an emitter.

P-doped all-small-molecule organic solar cells with power conversion efficiency of 17.73%

All-small organic solar cells(ASM OSCs)inherit the advantages of the distinct merits of small molecules,such as well-defined structures and less batch-to-batch variation.In comparison with the rapid development of polymer-based OSCs,more efforts are needed to devote to improving the performance of ASM OSCs to close the performance gap between ASM and polymer-based OSCs.Herein,a well-known p-dopant named fluoro-7,7,8,8-tetracyano-p-quinodimethane(FTCNQ)was introduced to a highefficiency system of HD-1:BTP-e C9,and a high power conversion efficiency(PCE)of 17.15%was achieved due to the improved electrical properties as well as better morphology of the active layer,supported by the observed higher fill factor(FF)of 79.45%and suppressed non-radiative recombination loss.Furthermore,combining with the further morphology optimization from solvent additive of 1-iodonaphthalene(IN)in the blend film,the HD-1:BTP-e C9-based device with the synergistic effects of both FTCNQ and IN demonstrates a remarkable PCE of 17.73%(certified as 17.49%),representing the best result of binary ASM OSCs to date.

Adaptive Power Control Based on Double-layer Q-learning Algorithm for Multi-parallel Power Conversion Systems in Energy Storage Station

An energy storage station(ESS)usually includes multiple battery systems under parallel operation.In each battery system,a power conversion system(PCS)is used to connect the power system with the battery pack.When allocating the ESS power to multi-parallel PCSs in situations with fluctuating operation,the existing power control methods for parallel PCSs have difficulty in achieving the optimal efficiency during a long-term time period.In addition,existing Q-learning algorithms for adaptive power allocation suffer from the curse of dimensionality.To overcome these challenges,an adaptive power control method based on the double-layer Q-learning algorithm for n parallel PCSs of the ESS is proposed in this paper.First,a selection method for the power allocation coefficient is developed to avoid repeated actions.Then,the outer action space is divided into n+1 power allocation modes according to the power allocation characteristics of the optimal operation efficiency.The inner layer uses an actor neural network to determine the optimal action strategy of power allocations in the non-steady state.Compared with existing power control methods,the proposed method achieves better performance for both static and dynamic operation efficiency optimization.The proposed method optimizes the overall operation efficiency of PCSs effectively under the fluctuating power outputs of the ESS.

Application of Single-to-Single Phase Matrix Conversion in Conventional Rectifier-Inverter

The principle of single to single phase matrix electric power conversioin is further studied and the conversioin switch function is introduced into conventional rectifier inverter, thus a general character of the two conversion techniques is discovered. It is characteristic of the switch functiion to follow mains voltage distortion and mains frequency drift. By utilizing the merit, unidirectional switch duty rations of the inverter follow the variation of DC link voltage automatically, thus the size of DC link electrolytic capacitor can be reduced considerably, bringing about improved mains side power factor. Corresponding topologies and theoretical and theoretical derivations are given, and so are the simulation results, based on which it is confirmed that the single to single phase matrix conversion technique is potentially useful in large scale production, and the introduction of switch function can yield good economic returns.

Layered-stacking of titania films for solar energy conversion:Toward tailored optical,electronic and photovoltaic performance

Nanostructured TiO2 with differentiate morphologies has attracted tremendous attention due to its wide band-gap nature as well as outstanding optical and electric properties for solar-driven light-toelectricity conversion application. Layered-stacking TiO2 film such as double-layer, tri-layer, quadrupleor quintuplicate-layer, is highly desirable to the design of high-performance semiconductor material photoanodes and the development of advanced photovoltaic devices. In this minireview, we will summarize the recent progress and achievements on proof-of-concept of layered-stacking TiO2 films（LTFs） for solar cells with emphasis on the tailored properties and synergistic functionalization of LTFs, such as optimized sensitizer adsorption, broadened light confinement as well as facilitated electron transport characteristics.Various demonstrations of LTFs photovoltaic systems provide lots of possibilities and flexibilities for more efficient solar energy utilization that a wide variety of TiO2 with distinguished morphologies can be integrated into differently structured photoanodes with synergistic and complementary advantages. This key structure engineering technology will also pave the way for the development of next generation state-ofthe-art electronics and optoelectronics. Finally, from our point of view, we conclude the future research interest and efforts for constructing more efficient LTFs as photoelectrode, which will be highly warranted to advance the solar energy conversion process.

Analysis of Power Model for Linear Plasma Device

A single cathode linear plasma device has been designed and constructed to investigate the interactions between plasma and materials at the Sichuan University. In order to further investigate the Ohmic power of the device, the output heat load on the specimen and electric potential difference（between cathode and anode） have been tested under different discharge currents. This special power distribution in the radial direction of the plasma discharge channel has also been discussed and described by some improved integral equations in this paper;it can be further simplified as P ∝ α^（-2） in one-parameter. Besides, we have measured the power loss of the channel under different discharge currents by the calorimetric method, calculated the effective power of the device and evaluated the performances of the plasma device through the power efficiency analysis.

An Adaptive Wireless Power Sharing Control for Multiterminal HVDC

Power sharing among multiterminal high voltage direct current terminals(MT-HVDC)is mainly developed based on a priority or sequential manners,which uses to prevent the problem of overloading due to a predefined controller coefficient.Furthermore,fixed power sharing control also suffers from an inability to identify power availability at a rectification station.There is a need for a controller that ensures an efficient power sharing among the MT-HVDC terminals,prevents the possibility of overloading,and utilizes the available power sharing.A new adaptive wireless control for active power sharing among multiterminal(MT-HVDC)systems,including power availability and power management policy,is proposed in this paper.The proposed control strategy solves these issues and,this proposed controller strategy is a generic method that can be applied for unlimited number of converter stations.The rational of this proposed controller is to increase the system reliability by avoiding the necessity of fast communication links.The test system in this paper consists of four converter stations based on three phase-two AC voltage levels.The proposed control strategy for a multiterminal HVDC system is conducted in the power systems computer aided design/electromagnetic transient design and control(PSCAD/EMTDC)simulation environment.The simulation results significantly show the flexibility and usefulness of the proposed power sharing control provided by the new adaptive wireless method.

Enhancing the crystallinity and stability of perovskite solar cells with 4-tert-butylpyridine induction for efficiency exceeding 24%

Perovskite solar cells(PSCs)have emerged as a promising photovoltaic technology because of their high light absorption coefficient,long carrier diffusion distance,and tunable bandgap.However,PSCs face challenges such as hysteresis effects and stability issues.In this study,we introduced a novel approach to improve film crystallization by leveraging 4-tert-butylpyridine(TBP)molecules,thereby enhancing the performance and stability of PSCs.Our findings demonstrate the effective removal of PbI_(2)from the perovskite surface through strong coordination with TBP molecules.Additionally,by carefully adjusting the concentration of the TBP solution,we achieved enhanced film crystallinity without disrupting the perovskite structure.The TBP-treated perovskite films exhibit a low defect density,improved crystallinity,and improved carrier lifetime.As a result,the PSCs manufactured with TBP treatment achieve power conversion efficiency(PCE)exceeding 24%.Moreover,we obtained the PCE of 21.39%for the 12.25 cm^(2)module.

High Efficiency Formamidinium-Cesium Perovskite-Based Radio-Photovoltaic Cells

Radio-photovoltaic cell is a micro nuclear battery for devices operating in extreme environments,which converts the decay energy of a radioisotope into electric energy by using a phosphor and a photovoltaic converter.Many phosphors with high light yield and good environmental stability have been developed,but the performance of radio-photovoltaic cells remains far behind expectations in terms of power density and power conversion efficiency,because of the poor photoelectric conversion efficiency of traditional photovoltaic converters under low-light conditions.This paper reports an radio-photovoltaic cell based on an intrinsically stable formamidinium-cesium perovskite photovoltaic converter exhibiting a wide light wavelength response from 300 to 800 nm,high open-circuit voltage(V_(oc)),and remarkable efficiency at low-light intensity.When a He ions accelerator is adopted as a mimickedαradioisotope source with an equivalent activity of 0.83 mCi cm^(-2),the formamidinium-cesium perovskite radio-photovoltaic cell achieves a V_(oc)of 0.498 V,a short-circuit current(J_(sc))of 423.94 nA cm^(-2),and a remarkable power conversion efficiency of 0.886%,which is 6.6 times that of the Si reference radio-photovoltaic cell,as well as the highest among all radio-photovoltaic cells reported so far.This work provides a theoretical basis for enhancing the performance of radio-photovoltaic cells.

Dimethyl acridine-based self-assembled monolayer as a hole transport layer for highly efficient inverted perovskite solar cells

Self-assembled monolayers(SAMs)have recently emerged as excellent hole transport materials in inverted perovskite solar cells(PSCs)owing to their ability to minimize parasitic absorption,regulate energy level alignment,and passivate perovskite defects.Herein,we design and synthesize a novel dimethyl acridinebased SAM,[2-(9,10-dihydro-9,9-dimethylacridine-10-yl)ethyl]phosphonic acid(2PADmA),and employ it as a hole-transporting layer in inverted PSCs.Experimental results show that the 2PADmA SAM can modulate perovskite crystallization,facilitate carrier transport,passivate perovskite defects,and reduce nonradiative recombination.Consequently,the 2PADmA-based device achieves an enhanced power conversion efficiency(PCE)of 24.01%and an improved fill factor(FF)of 83.92%compared to the commonly reported[2-(9H-carbazol-9-yl)ethyl]phosphonic acid(2PACz)-based control device with a PCE of 22.32%and FF of 78.42%,while both devices exhibit comparable open-circuit voltage and short-circuit current density.In addition,2PADmA-based devices exhibit outstanding dark storage and thermal stabilities,retaining approximately~98%and 87%of their initial PCEs after 1080 h of dark storage and 400 h of heating at 85°C,respectively,both considerably superior to the control device.

Review of current progress in hole-transporting materials for perovskite solar cells

Recent advancements in perovskites’ application as a solar energy harvester have been astonishing. The power conversion efficiency(PCE) of perovskite solar cells(PSCs) is currently reaching parity(>25 percent), an accomplishment attained over past decades. PSCs are seen as perovskites sandwiched between an electron transporting material(ETM) and a hole transporting material(HTM). As a primary component of PSCs, HTM has been shown to have a considerable effect on solar energy harvesting, carrier extraction and transport, crystallization of perovskite, stability, and price. In PSCs, it is still necessary to use a HTM.While perovskites are capable of conducting holes, they are present in trace amounts, necessitating the use of an HTM layer for efficient charge extraction. In this review, we provide an understanding of the significant forms of HTM accessible(inorganic, polymeric and small molecule-based HTMs), to motivate further research and development of such materials. The identification of additional criteria suggests a significant challenge to high stability and affordability in PSC.