Progress of power field effect transistor based on ultra-wide bandgap Ga_2O_3 semiconductor material

As a promising ultra-wide bandgap semiconductor, gallium oxide(Ga_2O_3) has attracted increasing attention in recent years. The high theoretical breakdown electrical field(8 MV/cm), ultra-wide bandgap(～ 4.8 eV) and large Baliga's figure of merit(BFOM) of Ga_2O_3 make it a potential candidate material for next generation high-power electronics, including diode and field effect transistor(FET). In this paper, we introduce the basic physical properties of Ga_2O_3 single crystal, and review the recent research process of Ga_2O_3 based field effect transistors. Furthermore, various structures of FETs have been summarized and compared, and the potential of Ga_2O_3 is preliminary revealed. Finally, the prospect of the Ga_2O_3 based FET for power electronics application is analyzed.

Preliminary Design of Poloildal Field Power Supply for HT-7U Super-conducting Tokamak

This paper presents the preliminary design of poloidal field power supply system of HT-7U super-conducting tokamak. With an emphasis on AC/DC power converter, DC circuit breaker, quench protection, harmonic suppression and static var. compensation, and AC power system, the design principle and features are introduced, the design scheme and R & D progress are described, the simulation studies and laboratory test are presented too.

The training process： Planning for strength-power training in track and field. Part 1： Theoretical aspects

力量—爆发力训练的过程和随后的适应受多种因素影响。这其中包括运动员的基因、形态特征以及教练如何选择、安排及实施、训练和负荷模式。针对上述训练因素的适应能力很大程度上与传授模式,即项目策略有很大关系。有研究证明,运动员在训练中表现出的模式和阶段对表现结果有深远的影响。本文讨论了模块式周期性训练的概念以及田径运动中力量—爆发力训练过程的相关方法。

On the Sequential Control of ITER Poloidal Field Converters for Reactive Power Reduction

Sequential control applied to the International Thermonuclear Experimental Re- actor （ITER） poloidal field converter system for the purpose of reactive power reduction is the subject of this investigation. Due to the inherent characteristics of thyristor-based phase-controlled converter, the poloidal field converter system consumes a huge amount of reactive power from the grid, which subsequently results in a voltage drop at the 66 kV busbar if no measure is taken. The installation of a static var compensator rated for 750 MVar at the 66 kV busbax is an essential way to compensate reactive power to the grid, which is the most effective measure to solve the problem. However, sequential control of the multi-series converters provides an additional method to improve the natural power factor and thus alleviate the pressure of reactive power demand of the converter system without any additional cost. In the present paper, by comparing with the symmetrical control technique, the advantage of sequential control in reactive power consumption is highlighted. Simulation results based on SIMULINK are found in agreement with the theoretical analysis.

Coupling Effect between Equilibrium Field and Heating Field and Modification of the Power Supply System on SUNIST Spherical Tokamak

Strong inductive coupling between the heating field and equilibrium field is confirmed to be responsible for the poor plasma equilibrium in initial discharges on the SUNIST spherical tokamak. A modification project for the power supply system of equilibrium field coils is successfully performed to increase the duration time of plasma current flattop from much less than 1ms to about 2 ms.

Field plate structural optimization for enhancing the power gain of GaN-based HEMTs

A novel source-connected field plate structure, featuring the same photolithography mask as the gate electrode, is proposed as an improvement over the conventional field plate （FP） techniques to enhance the frequency performance in GaN-based HEMTs. The influences of the field plate on frequency and breakdown performance are investigated simul- taneously by using a two-dimensional physics-based simulation. Compared with the conventional T-gate structures with a field plate length of 1.2 gm, this field plate structure can induce the small signal power gain at 10 GHz to increase by 5-9.5 dB, which depends on the distance between source FP and dramatically shortened gate FE This technique minimizes the parasitic capacitances, especially the gate-to-drain capacitance, showing a substantial potential for millimeter-wave, high power applications.

Association between Childhood Leukaemia and Exposure to Power-frequency Magnetic Fields in Middle Europe

Abstract Objective Higher levels of exposure to extremely low-frequency magnetic fields （ELF-MF） are associated with a slightly increased risk of childhood leukaemia. Compared with more-developed Western countries, higher exposure levels are evident in the Czech Republic, probably because of the different types of housing. In light of this, we aimed to examine the association between ELF-MF exposure and childhood leukaemia in the Czech Republic. Methods We conducted a paired case-control study. The cases （children with leukaemia） were age- sex- and permanent residence-matched to controls （children without leukaemia）. Although this limited potential bias and confounding, it also limited our number of participants. Results The matched analyses included 79 case-control pairs. No significant association between ELF-MF exposure and childhood leukaemia was observed for exposures over 0.2 μT （odds ratio [0R]=0.93, confidence interval [Cl]=0.45-1.93）, 0.3 μT （0R=0.77, Cl=0.34-1.75）, or 0.4 μT （OR=0.9, Cl=0.37-2.22）. Conclusion Despite higher levels of exposure in Middle and Eastern Europe, no indication of an association between ELF-MF exposure and childhood leukaemia was determined. This in contrast to the findings of previous studies conducted in different countries.

The Power Supply System for the J-TEXT Poloidal Field

Joint-TEXT （J-TEXT） is a medium-sized tokamak constructed at Huazhong University of Science and Technology. At present, the poloidal field power supply consists of three subsystem sets, namely Ohmic heating field power supply, vertical field power supply, and horizontal field power supply. The structure and function of the poloidal field （PF） power supply as well as the updated control system of the power supply is described. The new scheme uses the realtime feedback control method for the poloidal field power supply. The experimental results show that the poloidal field energized by poloidal field power supply meets the J-TEXT operational requirement perfectly.

Improved Method of Power Loss and Electric Field Calculations of HVAC Transmission Lines

An improved method for calculating the corona power loss and the ground-level electric field on HVAC transmission lines induced by corona is proposed.Based on a charge simulation method combined with a method of successive images,the proposed method has the number and location of the simulated charges not arbitrary.When the surface electric field of a conductor exceeds the onset value,charges are emitted from corona into the space around,and the space ions and the surface charges on each sub-conductor are simulated by using the images of the other sub-conductors.The displacements of the space ions are calculated at every time step during corona periods in both the positive and the negative half cycles.Several examples are calculated by using the proposed method,and the calculated electric field at the ground level and the corona power loss agree well with previous measurements.The results show that simulating 12 charges in each conductor during 600 time steps in one cycle takes less time while guarantees the accuracy.The corona discharge from a 220 kV transmission line enhances slightly(less than 2%) the electric field at the ground level,but this effect is little from a 500 kV line.The improved method is a good compromise between the time cost and the accuracy of calculation.

Effect of focused ultrasound stimulation at different ultrasonic power levels on the local field potential power spectrum

Local field potential(LFP) signals of the rat hippocampus were recorded under noninvasive focused ultrasound stimulation(FUS) with different ultrasonic powers. The LFP mean absolute power was calculated with the Welch algorithm at the delta, theta, alpha, beta, and gamma frequency bands. The experimental results demonstrate that the LFP mean absolute power at different frequency bands increases as the ultrasound power increases.

Effect of aperture field distribution on the maximum radiated power at atmospheric pressure

The air breakdown in the high-power antenna near-field region limits the enhancement of the radiated power. A model coupling the field equivalent principle and the electron number density equation is presented to study the breakdown process in the near-field region of the circular aperture antenna at atmospheric pressure. Simulation results show that, although the electric field in the near-field region is nonuniform, the electron diffusion has small influence on the breakdown process when the initial electron number density is uniform in space. The field magnitude distribution on the aperture plays an important role in the maximum radiated power above which the air breakdown occurs. The maximum radiated power also depends on the phase difference of the fields at the center and edge of the aperture, especially for the uniform field magnitude distribution.

A Consideration on Increasing Current Density in Normal Conducting Toroidal Field Coil for Spherical Tokamak Power Plant

The center post is the most critical component as an inboard part of the toroidal field coil for the low aspect ratio tokamak. During the discharge it endures not only a tremendous ohmic heating owing to its carrying a rather high current but also a large nuclear heating and irradiation owing to the plasma operation. All the severe operating conditions, including the structure stress intensity and the stability of the structure, largely limit the maximum allowable current density. But in order to contain a very high dense plasma, it is hoped that the fusion power plant system can operate with a much high maximum magnetic field BT ≥12 T-15 T in the center post. A new method is presented in this paper to improve the maximum magnetic field up to 17 T and to investigate the possibility of the normal conducting center post to be used in the future fusion tokamak power plant.

Correction of Observation Interference on Z component of Geomagnetic Field From DC Power Lines

为减小直流输电线路对地磁场观测的干扰,采用数学计算的方法精确求解了线路对地磁Z分量的干扰水平。以观测点为原点建立了地磁仪器观测点坐标系,推导了观测点坐标系各坐标轴在地心坐标系中的单位矢量表达式。根据空间矢量点积的定义,得到了空间电流磁场矢量投影到地磁Z分量方向的求解公式。利用推导的公式和直流线路电流磁场三维计算模型,最终求得直流线路对地磁Z分量观测的干扰水平。由此,开发了＂直流线路对地磁观测干扰校正系统＂,并开展了地磁台站和野外联合地磁观测干扰实验。结果表明,直流线路和地磁观测台站距离不超过10km时,提出的数学模型和计算方法误差不超过5%。

A New Approach of Time Series Variation Based on Power Links and Field Association Words

This paper has proposed a new methodology extracting stability classes of field association words depending on automatically power link analysis to enhance the precision of decision tree. In this paper, we have studied the effects of the time variation based on the frequencies of specific words called field association words that connected to documents using power link in a specific period. The stability classes have referred to the popularity of field association words based on the change of time in a given period. The new approach has evaluated by conducting experiments simulating results of 1575 files (about 5.16 MB). Based on these experiments, it has turned out that, the F-measure for ascending, stable and descending classes have achieved 93.6%, 99.8% and 75.7%, respectively. These results mean that F-measure was increasing by 12%, 4% and 34% than traditional methods because of the power link analysis.

Design and Analysis of the Poloidal Field Grid Power Supply System for the HT-7 Tokamak

This paper reports a new project - the poloidal field （PF） grid power supply system to replace the ac flywheel generator power supply system on the basis of the present running parameters of the HT-7 poloidal field and the short-circuit capacity of our transformer substation. The designed parameters of the PF grid power supply system have been verified to meet the requirements of the heating field （HF） and the vertical field （VF）. In the meantime, in order to reduce the disturbance to the local power grid, the device of reactive power and harmonic current compensation has been added. Experimental results have confirmed the feasibility of the PF grid power supply system. Compared with the ac flywheel generator, the PF grid power supply system has the advantages of lower noise, precise control, convenient maintenance, simple operation and cost savings.

A Conceptual Design Study for the Error Field Correction Coil Power Supply in JT-60SA

This paper describes a conceptual design study for the circuit configuration of the Error Field Correction Coil （EFCC） power supply （PS） to maximize the expected performance with reasonable cost in JT-60SA. The EFCC consists of eighteen sector coils installed inside the vacuum vessel, six in the toroidal direction and three in the poloidal direction, each one rated for 30 kA-turn. As a result, star point connection is proposed for each group of six EFCC coils installed cyclically in the toroidal direction for decoupling with poloidal field coils. In addition~ a six phase inverter which is capable of controlling each phase current was chosen as PS topology to ensure higher flexibility of operation with reasonable cost.

Three-Dimensional Study of the Effect of the Angle of Incidence of a Magnetic Field on the Electrical Power and Conversion Efficiency of a Polycrystalline Silicon Solar Cell under Multispectral Illumination

A three-dimensional approach to the effect of magnetic field incidence angle on electrical power and conversion efficiency is performed on a front-illuminated polycrystalline silicon bifacial solar cell. A solution of the continuity equation allowed us to present the equations of photocurrent density, photovoltage and electric power. The influence of the angle of incidence of the magnetic field on the photocurrent density, the photovoltage and the electric power has been studied. The curves of electrical power versus dynamic junction velocity were used to extract the values of maximum electrical power and dynamic junction velocity and to calculate those of conversion efficiency. From this study, it is found that the conversion efficiency values increase with the angle of incidence of the magnetic field.

A Simulation Study on the Specific Loss Power in Magnetic Hyperthermia in the Presence of a Static Magnetic Field

Our purpose in this study was to present a method for estimating the specific loss power (SLP) in magnetic hyperthermia in the presence of an external static magnetic field (SMF) and to investigate the SLP values estimated by this method under various diameters (D) of magnetic nanoparticles (MNPs) and amplitudes (H0) and frequencies (f) of an alternating magnetic field (AMF). In our method, the SLP was calculated by solving the magnetization relaxation equation of Shliomis numerically, in which the magnetic field strength at time t (H(t)) was assumed to be given by , with Hs being the strength of the SMF. We also investigated the SLP values in the case when the SMF with a field-free point (FFP) generated by two solenoid coils was used. The SLP value in the quasi steady state (SLPqss) decreased with increasing Hs. The plot of the SLPqss values against the position from the FFP became narrow as the gradient strength of the SMF (Gs) increased. Conversely, it became broad as Gs decreased. These results suggest that the temperature rise and the area of local heating in magnetic hyperthermia can be controlled by varying the Hs and Gs values, respectively. In conclusion, our method will be useful for estimating the SLP in the presence of both the AMF and SMF and for designing an effective local heating system for magnetic hyperthermia in order to reduce the risk of overheating surrounding healthy tissues.

基于小波变换和压缩感知的工频磁异常信号降噪方法

针对强噪声背景下水下目标微弱工频磁异常信号提取困难的问题,提出一种基于小波变换的压缩感知降噪方法。该方法利用噪声信号不具有稀疏性的特点,将含噪信号在小波域内分解,并在此基础上进行压缩感知的重构与降噪处理,实现微弱工频磁异常信号与噪声最大限度地分离。仿真及试验表明,该方法得到很好的降噪效果,避免了小波阈值滤波中阈值选取对降噪效果的影响,能够最大程度地保留原始信号的固有特征。

750kV单回并行输电线路电磁辐射环境研究

采用《环境影响评价技术导则输变电》(HJ 24—2020)附录C、D推荐的计算模式对750 kV单回并行输电线路电磁辐射环境进行计算与预测。结果表明,经过耕地、园地、牧草地、畜禽饲养地、道路等场所,当导线对地最小高度为15.5 m时,单回并行线路下的工频电场强度最大值超过10 kV/m;需将导线对地最小高度提至16.5 m,才能满足4 kV/m控制限值要求。750 kV单回并行输电线路产生的工频磁场强度小于公众曝露控制限值(100μT),一般情况下不会成为线路建设的环境制约因素;但其产生的工频电场是电磁环境影响的主要因素,电场强度控制限值(4 kV/m)是线路建设的环境制约因素,同时也是输变电电磁环境重点控制因素。现场实测结果与理论预测结果符合性较好,表明采用的预测模式具有较好的应用性,研究结果可为750 kV单回并行输电线路的建设和环境监管提供支持。