Effect of power frequency excitation character on ferroresonance in neutral-grounded system

In most earlier ferroresonance studies the traditional excitation characteristic of iron core, in which the traditional excitation characteristic contains harmonic voltages or currents, has been used as if it were made up of pure fundamental voltage or current. However, this is not always true. In comparison with traditional excitation characteristics, this paper introduces the power frequency excitation characteristic of the iron core, which contains no harmonics. The power frequency excitation characteristic of iron core has been obtained by Elector Magnetic Transient Program, resulting in discrete voltage and current pairs. Extensive simulations are carried out to analyse the effect of power frequency excitation characteristic on potential transformer ferroresonance. A detailed analysis of simulation results demonstrates that with power frequency excitation characteristic of iron core inclusion at certain excitation voltage the ferroresonance may happen, conversely it may not happen with traditional excitation characteristic inclusion.

Industrial frequency single-phase AC traction power supply system for urban rail transit and its key technologies

To avoid stray current and maintain the benefit of no phase-split in the DC traction power supply system, an AC traction power supply system was proposed for the urban public transport such as metro and light rail transit. The proposed system consists of a main substation （MSS） and cable traction network （CTN）. The MSS includes a single-phase main traction transformer and a negative-se- quence compensation device, while the CTN includes double-core cables, traction transformers, overhead catenary system, rails, etc. Several key techniques for the proposed system were put forward and discussed, which can be summarized as （1） the power supply principle, equivalent circuit and transmission ability of the CTN, the cable-catenary matching technique, and the selection of catenary voltage level; （2） the segmentation technology and status identification method for traction power supply network, distributed and centralized protection schemes, etc.; （3） a power supply scheme for single-line MSS and a power supply scheme of MSS shared by two or more lines. The proposed industrial frequency single-phase AC traction power supply system shows an excellent technical performance, good economy, and high reliability, hence provides a new alternative for metro and urban rail transit power supply systems.

Amplified Spontaneous Emission in Single Frequency Double-Clad Fiber Power Amplifiers

Amplified spontaneous emission （ASE） in diode laser pumped double-clad fiber power amplifiers is studied experimentally, The dependences of ASE on fiber length and cross section of active core are discussed and the variations of ASE power as the function of pumping and signal power are investigated. There are indications that long fibers with large mode area need stronger input signals to suppress ASE. It is shown that a 150 mW input signal can suppress the ASE by 40 dB in a 4 m large mode area fiber, while to efficiently suppress the ASE in a 10 m fiber, stronger input signal is needed. 12.5 W and 16.1 W single frequency CW output power are obtained from 4 m fiber and 10 m fiber respectively. No stimulated Brillouin scattering （SBS） was observed

Phase field model for electric-thermal coupled discharge breakdown of polyimide nanocomposites under high frequency electrical stress

In contrast to conventional transformers, power electronic transformers, as an integral component of new energy power system, are often subjected to high-frequency and transient electrical stresses, leading to heightened concerns regarding insulation failures. Meanwhile, the underlying mechanism behind discharge breakdown failure and nanofiller enhancement under high-frequency electrical stress remains unclear. An electric-thermal coupled discharge breakdown phase field model was constructed to study the evolution of the breakdown path in polyimide nanocomposite insulation subjected to high-frequency stress. The investigation focused on analyzing the effect of various factors, including frequency, temperature, and nanofiller shape, on the breakdown path of Polyimide(PI) composites. Additionally, it elucidated the enhancement mechanism of nano-modified composite insulation at the mesoscopic scale. The results indicated that with increasing frequency and temperature, the discharge breakdown path demonstrates accelerated development, accompanied by a gradual dominance of Joule heat energy. This enhancement is attributed to the dispersed electric field distribution and the hindering effect of the nanosheets. The research findings offer a theoretical foundation and methodological framework to inform the optimal design and performance management of new insulating materials utilized in high-frequency power equipment.

Effect of PMD-induced Pulse Broadening on Sensitivity and Frequency Spectrum

The PMD-induced pulse broadening may cause the degradation ofreceiver sensitivity and has negative effects on the power spectrumof received signals. The expression s of PMO-induced pulse broadeningeffects on receiver sensitivity are derived based on the concept ofman square pulse width. The effects of PMD on the spectrum ofreceived power are analyzed in detail. Finally, the scheme isdiscussed with which the poser of a certain frequency component isextracted as a feedback control signal in a PMD compensation system.

Design Technologies for Silicon-Based High-Efficiency RF Power Amplifiers:A Brief Overview

This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency （RF） power amplifiers （PAs） as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking （ET） design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.

Investigation of Plasma Polymerized Maleic Anhydride Film in a Middle Frequency Dielectric Barrier Discharge

Plasma polymerized maleic anhydride （MA） was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge （DBD）. The film properties were characterized by water contact angle （WCA）, Fourier transfer infrared （FTIR）, X-ray photoelectron spectroscopy （XPS）, atomic force microscope （AFM） analysis, and a thickness profilometer. The influence of the processing parameters on the film properties such as tile power frequency and polymerization zone was investigated. The results show that anhydride group incorporated into the growing films is favorable at the frequency of 80 kHz and working pressure of 50 Pa. The poly （maleic anhydride） film is uniform and compact at an average deposition rate of 8 nm/min.

Improving Dynamic Stability of Yunnan Provincial and South China Power System by PSS

For solving the dynamic instability problem of Yunnan Provincial Power System (YNPS) and the South China Interconnected Power System (SCIPS), Lubuge Hydropower Station was chosen to install Power System Stabilizer (PSS). This paper introduces the principles and methods of parameter selection for PSS, in addition to field test. The test results show that the PSS installed can significantly improve the system damping.

Experimental Analysis of Radial Centrifugal Pump Shutdown

Centrifugal pumps are widely used in the metallurgy,coal,and building sectors.In order to study the hydraulic characteristics of a closed impeller centrifugal pump during its shutdown in the so-called power frequency and frequency conversion modes,experiments were carried to determine the characteristic evolution of parameters such as speed,inlet and outlet pressure,head,flow rate and shaft power.A quasi-steady-state method was also used to further investigate these transient behaviors.The results show that,compared to the power frequency input,the performance parameter curves for the frequency conversion input are less volatile and smoother.The characteristic time is longer and the response to shutdown is slower.The quasi-steady-state theoretical head-flow curves match the experimental head-flow curves more closely at low flow rates when the frequency conversion input is considered.Moreover,in this case,the similarity law predicts the hydraulic performance more accurately.

Exploiting demand-side heterogeneous flexible resources in risk management of power system frequency

More demand-side flexible resources(DFRs)are participating in the frequency regulation of renewable power systems,whose heterogeneous characteristics have a significant impact on the system frequency response.Consequently,selecting suitable DFRs poses a formidable challenge for independent system operators(ISO).In this paper,a reserve allocation methodology for heterogeneous DFRs is proposed to manage the risk of power system frequency.Firstly,a performance curve is developed to describe the cost,capacity,and response speed of DFRs.Moreover,a clustering method for multiple distributed DFRs is conducted to calculate the aggregated performance curves and uncertainty coefficients.Then,the frequency security criterion considering DFRs’performance is constructed,whose linearity makes it can be easily coupled into the system scheduling model and solved.Furthermore,a risk management model for DFRs considering frequency-chance-constraint is proposed to make a trade-off between cost and frequency security.Finally,the model is transformed into mixed integer second-order cone programming(MISOCP)and solved by the commercial solver.The proposed model is validated by the IEEE 30 and IEEE 118 bus systems.

A Parallel-type Load Damping Factor Controller for Frequency Regulation in Power Systems with High Penetration of Renewable Energy Sources

Renewable energy sources(RESs)are rapidly devel-oping and their substitution for traditional power generation poses significant challenges to the frequency regulation in power systems.The load damping factor D characterizes the active power of load that changes with power system frequency,which is an important factor influencing the frequency response.However,the value of D is small,resulting in the limitation in frequency regulation of the power system.This paper proposes a parallel-type load damping factor controller to enhance load damping factor by utilizing static var generators(SVGs)in substations.Additionally,it discusses the configuration method for the relevant parameters of the controller,evaluates its frequen-cy regulation capability,investigates the impact of large-scale application of the controller on static and dynamic loads,and conducts a comprehensive evaluation of the impact of the damping factor control process on the voltage stability of the main grid.The large-scale application of the proposed controller can significantly improve the frequency regulation capability,and almost have no influence on the working status of the load.It can also significantly improve the dynamic performance of system frequency.The proposed controller can provide technical support for the frequency regulation of new power systems with high proportion of RESs.

Design of a weak bioelectric signal acquisition circuit

A surface electromyography(sEMG)signal acquisition circuit based on high-order filtering is designed.We use a two-stage adjustable amplifier and a high-order Sallen-Key bandpass filter to solve the problems of non-adjustable amplification gain and low filtering order in traditional acquisition circuits.The experimental results show that the designed sEMG signal acquisition device can eliminate power frequency interference effectively,the stopband drop of the filtering part reaches approximately-100 dB/dec,which can effectively extract useful signals between 20-500 Hz,and the amplification gain reaches 60 dB.

Analysis of temperature field for a surface-mounted and interior permanent magnet synchronous motor adopting magnetic-thermal coupling method

Aiming at obtaining high power density of surface-mounted and interior permanent magnet synchronous motor(SIPMSM),it is important to accurately calculate the temperature field distribution of SIPMSM,and a magnetic-thermal coupling method is proposed.The magnetic-thermal coupling mechanism is analyzed.The thermal network model and finite element model are built by this method,respectively.The effects of power frequency on iron losses and temperature fields are analyzed by the magnetic-thermal coupling finite element model under the condition of rated load,and the relationship between the load and temperature field is researched under the condition of the synchronous speed.In addition,the equivalent thermal network model is used to verify the magnetic-thermal coupling method.Then the temperatures of various nodes are obtained.The results show that there are advantages in both computational efficiency and accuracy for the proposed coupling method,which can be applied to other permanent magnet motors with complex structures.

Protective effect of compressing arc extinguishing lightning protection device on superimposed lightning strikes

Traditional lightning protection measures can not solve the problem of superimposed lightning strikes.This paper presents a compressing arc extinguishing lightning protection device,which can solve the problem of superimposed lightning strikes.This device can extinguish the power frequency continuous current arc quickly in 1-2 ms.It is far less than the response time of relay protection,which can avoid lightning trips and improve the reliability of power supply.The computer simulation and engineering practice show that the compressing arc extinguishing device has good protection effect on superimposed lightning strikes.

Corona noise model of high-voltage AC transmission lines and engineering applications

In order to predict the levels of corona noise from high-voltage alternating current （AC） transmission lines, the mechanism of corona noise and the corresponding theoretical prediction model are investigated. On the basis of Drnde model, the motion of positive and negative ions produced by high-voltage corona is analyzed, and the mechanism of corona noise is discovered. The theoretical prediction model is put forward by using Kirchhoff formula, which is verified by the well agreement between our result and others＇ , considering the case of three- phase single lines. Moreover, the calculation results show that for both single and bundled lines, the sound pres- sure level of the typical frequency, i.e. twice the power frequency, attenuates slowly and leads to an obviously in- terferential phenomenon near the transmission lines, but the level of the bundled lines is smaller than that of the single ones under the same transmission voltage. Based on the mechanism of corona noise and the prediction model, it is obvious that bundled lines and/or increased line radius can be adopted to reduce corona noise in the practical engineering applications effectively. This model can also provide a theoretical guidance for the high-volt- age AC transmission line design.

Study on Over-Voltage of 220 kV Transformer＇s Neutrals and Protection Strategy

In order to limit short-circuit current and satisfy the need of relay setting, only part of the 220 kV power transformer is grounded, so on the neutrals of ungrounded transformers will appear the over-voltage. Currently the value of over-voltage on transformer neutral point and the corresponding protection strategy is based on theoretical formula. This article uses the PSCAD/EMTDC software to calculate the over-voltage on the neutral point of 4 ungrounded power transformers in Chongqing 220 kV power grid. The result shows that the power frequency transient over-voltage on the neutrals may reach 178 kV. If the single-phase grounding fault occurs in ungrounded power system, the power frequency over-voltage on the neutrals will be more serious and rise to 138.6 kV. Non-full phase operation may cause serious ferro-resonance over-voltage on the neutrals of no-load transformer, which may last for seconds and may rise to 723.7 kV, causing serious threat to the transformer neutrals and line-side equipment. The article also studies the gap parameter which should be taken on the neutrals of 220 kV transformers at the end.

Design theory and experimental investigation of the low frequency and high power rare earth magnetostrictive flextensional transducer (Ⅰ). Theoretical part

The energy relationships among all the elements, by which the magnetostrictive transducers are manufactured, in Finite Element Method (FEM) are analyzed, then the expres- sions of FEM dynamics equations and performances formulas for magnetostrictive transducers are derived. The vibrating modes of the class VII transducer and its shell vibration are calcu- lated theoretically and the results point out that there is a breathing mode and if the transducer works at this mode, the transducer will vibrate with a greater volume speed and source level.

Determination of total sulfur in geothermal water by inductively coupled plasma-atomic emission spectrometry

Sulfur speciation and concentration in geothermal water are of great significance for the research and utilization of the water resources.In most situations,it is necessary to determine the total sulfur in geothermal water.In this study,the method was established for the determination of determining total sulfur content-the inductively coupled plasma-atomic emission spectrometry(ICP-AES),with the wavelength of 182.034 nm selected in spectral line of sulfur.It was identified that the optimal working conditions of the ICP-AES instrument were 1200 W for high frequency generator power 9 mm for vertical observation height,0.30 MPa atomizer pressure,and 50 r/min analytical pump speed.The matrix interference of the method was eliminated by the matrix matching method.Using this method,sulfur detection limit and minimum quantitative detection limit were 0.028 mg/L and 0.110 mg/L,respectively,whilst the linear range was 0.0-100.0 mg/L.The recovery rate of sample was between 90.67%and 108.7%,and the relative standard deviation(RSD)was between 0.36%and 2.14%.The method was used to analyze the actual samples and the results were basically consistent with the industry standard method.With high analysis efficiency,the method has low detection limit and minimum quantitative detection limit,wide linear range,good precision and accuracy,and provides an important detection method for the determination of total sulfur in geothermal water.

INVESTIGATION OF DOMINANT FREQUENCIES IN TRANSITION REYNOLDS NUMBER RANGE OF FLOW AROUND A CIRCULAR CYLINDER PARTⅡ: THEORETICAL DETERMINATION OF THE RELATIONSHIP BETWEEN VORTEX SHEDDING AND TRANSITION FREQUENCIES AT DIFFERENT REYNOLDS NUMBERS

An attempt has been made to explore whether the power relation can be obtained from theoretical considerations. The classical laminar and turbulent boundary layer concepts have been employed to determine appropriate values of the scaling lengths associated with vortex shedding and shear layer frequencies to predict the power law relationship with Reynolds number. The predicted results are in good agreement with experimental results. The findings will provide a greater insight into the overall phenomenon involved.

Measurement of acoustic field radiated by low frequency power ultrasonic transducer with laser-interferometer

Based on the piezo-optic effect of medium, the refractive index of medium is the function of its density, and so it's also the function of acoustic pressure. Therefore, acoustic pressure in the optical path everywhere can be determined absolutely by laser-interferometric technique and relative distribution of pressure in the middle and far acoustic field, which can be obtained from theory or experiment respectively. Theory and experiment of measurement of pressure in acoustic field with laser-interferometer are introduced. Distribution of pressure radiated by a power ultrasonic transducer is determined by laser interferometric technique. The theoretical and experimental results are in good agreement. The receiving sensitivity of a PVDF (Polyvinylidene fluoride) transducer in free field is also calibrated absolutely due to above results and its sensitivity is -118.5 dB.