Simulation by Dislocation Model and Anomaly Property Determination of Huge Leveling Deformation at Linfen Seismic Station

In this study,under the assumption that the two huge leveling deformation anomalies at Linfen seismic station were caused by the Luoyunshan fault( Tumen-Yuli section)movement, we computed the vertical deformation field distribution based on the rectangular fault dislocation model and measured the ground deformation field of the study area using D-InS AR technology. The results are as follows:( 1) Theoretically,the ground vertical deformation field caused by fault movement could be within the elliptical deformation area with the long axis parallel to the fault strike. The largest deformation region is located in the center of the area in the hanging wall of the fault,and the deformation gradually decreases to zero toward the periphery; the impact range induced by the two deformations is respectively as follows: The long axes are about 18 km and26km,the short axes are about 12 km and 17 km and the obvious deformation amplitude is about 1- 3mm and 4- 14 mm.( 2) The measured deformation field by D-InS AR shows that there is no continuous deformation area consistent with the fault strike,and only the presence of land subsidence possibly caused by groundwater excessive exploitation,with the deformation amplitude about 10- 12 mm and 1- 5mm.( 3) The measured deformation field is not consistent with the theoretical result on deformation area and amplitude,which indicates that the fault movement is not the main cause of Linfen huge leveling deformation,but may rather be because of local deformation of the soil layers in the hanging wall of the fault.( 4) By combining the fault dislocation model simulation with the D-InS AR technology measurement,we can determine effectively the nature of the anomalyof the huge cross-fault leveling deformation,thus provide scientific basis for verification of significant leveling anomalies.

Size effects on deformation behavior of C5210 phosphor bronze thin sheet

To investigate the effects of thickness and grain size on mechanical and deformation properties of C5210 phosphor bronze thin sheets, samples with different grain sizes were obtained through annealing heat treatment at different temperatures; and then tensile tests of samples with different thicknesses and grain sizes were conducted at room temperature. The results show that yield strength increases with decreasing thickness from 800 to 50 μm, but work hardening exponent and total elongation decrease, and a modified model was proposed to describe the relation between yield strength and thickness; yield strength decreases as the grain size increases, but work hardening exponent shows an increasing trend, total elongation increases to a peak and then decreases. Fracture morphology of tensile specimens was observed by SEM, which indicates that all tensile specimens are ductile fracture. The dimple intensity increases as the specimen thickness increases but reduces with the specimen grain size increasing.

Mechanical Behaviors and Deformation Properties of Retaining Wall Formed by Grouting Mould-Bag Pile

The simplified mechanical model and finite element model are established on the basis of the measured results and analysis of the grouting pile deformation monitoring,surface horizontal displacement and vertical displacement monitoring,deep horizontal displacement(inclinometer)monitoring,soil pressure monitoring and seepage pressure monitoring in the lower reaches of Wuan River regulation project in Shishi,Fujian Province.The mechanical behavior and deformation performance of mould-bag pile retaining wall formed after controlled cement grouting in the silty stratum of the test section are analyzed and compared.The results show that the use of controlled cement grouting mould-bag pile technology is to strengthen the soft stratum for sealing water and reinforcement,so that it can rock into a retaining wall,which can both retain soil and seal water with excellent effect.The control of cement grouting technology not only makes the soft soil rock in the range of retaining wall of mould-bag pile,but also makes a wide range of soil around the mould-bag pile squeeze and embed to compaction;and its cohesion and internal friction angle increased,so as to achieve the purpose of reducing soil pressure and improving mechanical and deformation properties of retaining wall.

Mechanical properties of lattice grid composites

An equivalent continuum method only considering the stretching deformation of struts was used to study the in-plane stiffness and strength of planar lattice grid com- posite materials. The initial yield equations of lattices were deduced. Initial yield surfaces were depicted separately in different 3D and 2D stress spaces. The failure envelope is a polyhedron in 3D spaces and a polygon in 2D spaces. Each plane or line of the failure envelope is corresponding to the yield or buckling of a typical bar row. For lattices with more than three bar rows, subsequent yield of the other bar row after initial yield made the lattice achieve greater limit strength. The importance of the buckling strength of the grids was strengthened while the grids were relative sparse. The integration model of the method was used to study the nonlinear mechanical properties of strain hardening grids. It was shown that the integration equation could accurately model the complete stress-strain curves of the grids within small deformations.

Draping Behavior of Carbon Non-Crimp Fabrics and Its Effects on Mechanical Performance of the Hemispherical Composites

In order to investigate the draping behavior of non-crimp fabrics（NCFs）, two types of carbon NCFs with tricot-chain stitches or chain stitches were formed on a hemispherical mould via a stretch forming process. The shear angle and forming defects of the fabrics were measured on the hemisphere, under different blank holder forces（BHFs）. The results showed that increasing BHF could enhance the shear angle slightly, reduce the asymmetry for the deformation of the fabrics, and change the main type of the process-induced defects. Besides, compression tests were performed on the corresponding composite components. By analyzing the change of fiber volume fraction and structural parameters of the textile reinforcements, the effects of draping behavior of NCFs on the mechanical performance of the composites were studied. The results reveal that draping process has distinguishable impacts on the mechanical properties of the final components, which is closely related to the stitching pattern of the NCFs.

Behavior of High Performance PVA Fiber Reinforced Cement Composites in Triaxial Compression

Based on an extensive experimental program,the paper studies the behavior of HPFRCC under triaxial compression. The experimental parameters are lateral confining pressure and PVA fiber content by volume. The test results indicate that ultimate strength and peak strain are significantly improved with the increases of confining pressure. The confining effect introduced by the fibers becomes minor in triaxial compression tests,where there is relatively high external confining pressure. The axial stress-strain curves with different confining pressure and different PVA fiber content by volume are obtained. Lateral confining pressure constraints the lateral expansion of HPFRCC,so there is a big plastic deformation with its ultimate strength improved. At lower confining pressure,PVA fiber content by volume has some effect on the decreased section of stress-strain curve. According to test results,the paper establishes formula of confining pressure with ultimate strength and axial peak strain respectively.

Mechanical Properties and Temper Resistance of Deformation Induced Ferrite in a Low Carbon Steel

The microstructures and mechanical properties of deformation induced ferrite （DIF） in the low carbon steel Q235 under different deformation temperatures have been investigated systematically. Through deformation induced ferrite transformation （DIFT）, ferrite grain can be refined to 3 μm and accounts for above 85% of the overall fraction. Yield strength of DIF （〉500 MPa） is increased by up to 100% compared with the conventional low carbon steel. Comparison of microstructure and mechanical properties in the Q235 steel with DIF and tempered DIF microstructure illustrates that the strengthening mechanism of DIF microstructure is the combination of grain boundary strengthening and carbon supersaturated strengthening. Electron back-scattered diffraction （EBSD） analysis and high magnification scanning electron microscopy （SEM） observation denote that high-angle grain boundary among ultrafine ferrite grain and the transformation product of retain austenite membrane along ferrite boundaries are responsible for the stability of ferrite grain size during tempering process. Transmission electron microscopy （TEM） analysis demonstrates that the transformation product of retained austenite membrane between ferrite grain boundaries is cementite.

Tensile behavior and deformation mechanism of quenching and partitioning treated steels at different deforming temperatures

The effects of deforming temperatures on the tensile behaviors of quenching and partitioning treated steels were investigated. It was found that the ultimate tensile strength of the steel decreased with the increasing temperature from 25 to 100 ℃, reached the maximum value at 300 ℃, and then declined by a significant extent when the temperature further reached 400 ℃. The total elongations at 100, 200 and 300 ℃are at about the same level. The steel achieved optimal mechanical properties at 300 ℃due to the proper transformation behavior of retained austenite since the stability of retained austenite is largely dependent on the deforming temperature. When tested at 100 and 200 ℃, the retained aus tenite was reluctant to transform, while at the other temperatures, about 10 vol. % of retained aus- tenite transformed during the tensile tests. The relationship between the stability of retained austenite and the work hardening behavior of quenching and partitioning treated steels at different deforming temperatures was also studied and discussed in detail. In order to obtain excellent mechanical properties, the stability of retained austenite should be carefully controlled so that the effect of transforma tion-induced plasticity could take place continuously during plastic deformation.

High Temperature Stress Rupture Anisotropy of a Ni-Based Single Crystal Superalloy

High temperature stress rupture anisotropies of a second generation Ni-base single crystal（SC） superalloy specimens with [001], [011] and [111] orientations under 900 ℃/445 MPa and 1100 ℃/100 MPa have been investigated in the present study, with attentions to the evolution of γ/γ′ microstructure observed by scanning electron microscopy and the dislocation configuration characterized by transmission electron microscopy in each oriented specimen. At 1100 ℃/100 MPa as well as 900 ℃/445 MPa, the single crystal superalloy exhibits obvious stress rupture anisotropic behavior. The [001] oriented specimen has the longest rupture lifetime at 900 ℃/445 MPa, and the [111] oriented sample shows the best rupture strength at 1100 ℃/100 MPa. While the [011] oriented specimen presents the worst rupture lifetime at each testing condition, its stress rupture property at 1100 ℃/100 MPa is clearly improved, compared with900 ℃/445 MPa. The evident stress rupture anisotropy at 900 ℃/445 MPa is mainly attributed to the distinctive movement way of dislocations in each oriented sample. Whereas, at 1100 ℃/100 MPa, together with the individual dislocation configuration, the evolution of γ/γ′ microstructure in each orientation also plays a key role in the apparent stress rupture anisotropy.

Evolution of microstructure and tensile properties of extruded Mg-4Zn-1Y alloy

In order to investigate the effect of extrusion on Mg-4Zn-1Y alloy, microstructure and mechanical properties were analyzed by optical microscopy（OM）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, energy dispersive spectrum（EDS） and tensile testing.The results indicated that the microstructure was obviously refined by extrusion and dynamic recrystallization.The second phases were dynamic precipitated and distributed more dispersively through extrusion.W-Phases（Mg3Zn3Y2） were twisted and broken, while I-Phases（Mg3Zn6Y） were spheroidized by deformation.Twin bands were formed to achieve the large deformation and hinder the slip of dislocations effectively to improve tensile properties.The tensile strength and elongation of extruded Mg-4Zn-1Y alloy were 254.94 MPa and 17.9% respectively which were improved greatly compared with those of as-cast alloy.The strengthening mechanisms of the extruded alloy were mainly fine-grain strengthening and distortion strengthening.

Influence of tension-twisting deformations and defects on optical and electrical properties of B,N doped carbon nanotube superlattices

As the era of nanoelectronics is dawning,CNT（carbon nanotube）,a one-dimensional nano material with outstanding properties and performances,has aroused wide attention.In order to study its optical and electrical properties,this paper has researched the influence of tension-twisting deformation,defects,and mixed type on the electronic structure and optical properties of the armchair carbon nanotube superlattices doped cyclic alternately with B and N by using the first-principle method.Our findings show that if tension-twisting deformation is conducted,then the geometric structure,bond length,binding energy,band gap and optical properties of B,N doped carbon nanotube superlattices with defects and mixed type will be influenced.As the degree of exerted tension-twisting deformation increases,B,N doped carbon nanotube superlattices become less stable,and B,N doped carbon nanotube superlattices with defects are more stable than that with exerted tension-twisting deformations.Proper tension-twisting deformation can adjust the energy gap of the system;defects can only reduce the energy gap,enhancing the system metallicity;while the mixed type of 5%tension,twisting angle of 15° and atomic defects will significantly increase the energy gap of the system.From the perspective of optical properties,doped carbon nanotubes may transform the system from metallicity into semi-conductivity.

Mechanical Properties and Microstructure Evolution of AA1100 Aluminum Sheet Processed by Accumulative Press Bonding Process

Accumulative press bonding（APB） is a novel variant of severe plastic deformation processes,which is devised to produce materials with ultra-fine grain.In the present work,the mechanical properties and microstructural evolution of AA1100 alloy,which is produced by APB technique,were investigated.The study of the microstructure of AA1100 alloy was performed by optical microscopy.The results revealed that the grain size of the samples decreased to 950 nm after six passes of APB process.The yield strength of AA1100 alloy after six passes of the process increased up to 264 MPa,which is three times higher than that of the as-cast material（89 MPa）.After six passes,microhardness values of AA1100 alloy increased from 38 to 61 HV.Furthermore,the results showed that the behavior of variations in mechanical properties is in accordance with the microstructural changes and it can be justified by using the Hall-Patch equation.Moreover,the rise in the yield strength can be attributed to the reduction in the grain size leading to the strain hardening.

Effects of γ-irradiation and Deformation Temperature on Tensile Properties of Pb-2 mass% Sb Alloy

Effects ofγ-irradiation and deformation temperature（T）on the tensile properties of Pb-2mass% Sb alloys were studied.The samples were annealed at 458 Kfor 2hin air,then water quenched after they wereγ-irradiated（the different doses were 0.5,1.0,1.5,and 2.0 MGy）.The tensile properties were performed using stress-strain measurements at a constant strain rate（1.2×10^（-3） s^（-1））and at different T（303-393K）.It was found that at constant dose,the fracture stress（σF）decreases while the fracture strain（εF）increases as Tincreases.At particular T,σFincreases whileεFdecreases with increasing dose.The strain-hardening exponent（n）,which is the slope of the relation between ln（σ）and ln（ε）of the parabolic part of the stress-strain curve,was determined and its values increase as Tincreases and decrease as the dose increases.The value of the activation energy increases as the dose increases from 0.07 eV for un-irradiated sample to 0.1eV for the 2 MGy-irradiated sample.These values are in accordance with that needed for dislocation movement and ordering process.An interpretation of the results was given,based on the creation of point and line defects due toγ-irradiation,and that results in a distribution of beta phase（Sb-phase）,leading to a difficulty in the movement of dislocations,so there is an increase in alloy hardness.

Tailoring Microstructure and Tribological Properties of Cold Deformed TiZrAlV Alloy by Thermal Treatment

Microstructure evolution and tribological properties of a new Ti Zr Al V alloy have been investigated in the present study. Various microstructures, i.e., equiaxed grain structure, dual-phase lamella structure, and heterogeneous lamellar structure, have been successfully prepared, and the effect of the microstructure on tribological properties was explored by means of cold severe plastic deformation combined with subsequent recrystallization annealing and aging treatments. The special heterogeneous lamellar-structured alloy exhibits a high ultimate tensile strength（~1545 MPa）,reasonable ductility（~7.9%）, and excellent wear resistance as compared with the equiaxed grain-structured and dualphase lamella-structured alloy. The present study demonstrates an alternative route for enhancing the tribological properties of alloys with heterogeneous lamellar structure.