Size transition of spiral waves using the pulse array method

The domain size of spiral waves is an important issue in studies of two-dimensional （2D） spatiotemporal patterns. In this work, we use the 2D complex Ginzburg-Landau equation （CGLE） as our model and find that an initially big spiral can successfully transfer to several small spirals by applying a pulse array method. The impacts of several important factors, such as array density, controlling intensity and pulsing time, are investigated. This control approach may be useful for the control of 2D spatiotemporal patterns and has potential applications in the control of some realistic systems, such as meteorological and cardiac systems.

Effects of synthetic conditions of pulse galvanostatic method on electroactivity of polyaniline

Nano-fibrous polyaniline was synthesized on stainless steel electrode in 0.5mol·L-1 H2SO4 solution by pulse galvanostatic method. The effects of synthetic conditions of pulse galvanostatic method on the electroactivity of polyaniline were investigated. The results show that the electroactivity of polyaniline film strongly depends on the synthetic conditions, such as the ratio of “on time” to “off time”(ton/toff), frequency, monomer concentration, temperature and mean current density. Different electroactivities of polyaniline are caused by different morphologies of polyaniline. The nano-fibrous polyaniline has higher electroactivity than polyaniline with other morphologies. Under the following conditions: mean current density of pulse galvanostatic method 13mA·cm-2, ton/toff 1, frequency 200Hz, monomer concentration 0.3mol·L-1 and temperature 20℃, nano-fibrous polyaniline film with the highest electroactivity can be obtained.

Preparation of Highly Textured Bi and MnBi Films by the Pulsed Laser Deposition Method

Textured Bi and MnBi/Bi thin films are prepared by the pulsed laser deposition method. The highly c-axis textured MnBi films are obtained by annealing the bilayer consisting of textured Bi and Mn films. The eoercivities of the MnBi/Bi film are 1.5 T and 2.35 T at room temperature and at 373K, respectively, showing a positive temperature coefficient. Microstructural investigations show that the textured MnBi film results from the orientated growth induced by the textured Bi under-layer.

Research and Application of Log Defect Detection and Visualization System Based on Dry Coupling Ultrasonic Method

In order to optimize the wood internal quality detection and evaluation system and improve the comprehensive utilization rate of wood,this paper invented a set of log internal defect detection and visualization system by using the ultrasonic dry coupling agent method.The detection and visualization analysis of internal log defects were realized through log specimen test.The main conclusions show that the accuracy,reliability and practicability of the system for detecting the internal defects of log specimens have been effectively verified.The system can make the edge of the detected image smooth by interpolation algorithm,and the edge detection algorithm can be used to detect and reflect the location of internal defects of logs accurately.The content mentioned above has good application value for meeting the requirement of increasing demand for wood resources and improving the automation level of wood nondestructive testing instruments.

Temporally Modulated Phase Retrieval Method for Weak Temporal Phase Measurement of Laser Pulses

We propose a simple iterative algorithm based on a temporally movable phase modulation process to retrieve the weak temporal phase of laser pulses. This unambiguous method can be used to achieve a high accuracy and to simultaneously measure the weak temporal phase and temporal profile of pulses, which are almost transform- limited. A detailed analysis shows that this iterative method has valuable potential applications in the charac- terization of pulses with weak temporal phase.

A novel nano-grade organosilicon polymer:Improving airtightness of compressed air energy storage in hard rock formations

Enhancing cavern sealing is crucial for improving the efficiency of compressed air energy storage(CAES)in hard rock formations.This study introduced a novel approach using a nano-grade organosilicon polymer(NOSP)as a sealant,coupled with an air seepage evaluation model that incorporates Knudsen diffusion.Moreover,the initial coating application methods were outlined,and the advantages of using NOSP compared to other sealing materials,particularly regarding cost and construction techniques,were also examined and discussed.Experimental results indicated a significant reduction in permeability of rock specimens coated with a 7–10μm thick NOSP layer.Specifically,under a 0.5 MPa pulse pressure,the permeability decreased to less than 1 n D,and under a 4 MPa pulse pressure,it ranged between4.5×10^(-6)–5.5×10^(-6)m D,marking a 75%–80%decrease in granite permeability.The sealing efficacy of NOSP surpasses concrete and is comparable to rubber materials.The optimal viscosity for application lies between 95 and 105 KU,and the coating thickness should ideally range from 7 to 10μm,applied to substrates with less than 3%porosity.This study provides new insights into air transport and sealing mechanisms at the pore level,proposing NOSP as a cost-effective and simplified solution for CAES applications.

A New Discriminating Experiment on the Invariance Hypothesis of Light Speed

This thesis puts forward a conjecture that, owing to some unknown special character of light, it is impossible to determine whether the speed of light is variable by the interference method. To verify the hypothesis of the invariance of light speed, a new method must be found to take accurate measurement of the infinitesimal change in the travelling time of light. The thesis suggests the adoption of high frequency laser pulse technology to carry out the measurement. On the basis of this idea a new discriminating experiment is proposed to test the hypothesis of the invariance of light speed. The thesis also makes some forecast of the future prospects of this experiment and of the future development of the theory of special relativity.

Fabrication and characterization of anodic oxide films on a Ti-10V-2Fe-3Al titanium alloy

Anodic oxide films of the titanium alloy Ti-10V-2Fe-3Al in ammonium tartrate electrolyte without hydrofluoric acid or fluoride were fabricated. The morphology, components, and microstructure of the films were characterized by scanning electron microscopy （SEM）, X-ray photoelectron spectroscopy （XPS）, X-ray diffraction （XRD）, and Raman spectroscopy. The results showed that the films were thick, uniform, and nontransparent. Such films exhibited sedimentary morphology, with a thickness of about 3 μm, and the pore diameters of the deposits ranged from several hundred nanometers to 1.5 μm. The films were mainly titanium dioxide. Some coke-like deposits, which may contain or be changed by OH, NH, C-C, C-O, and C=O groups, were doped in the films. The films were mainly amorphous with a small amount of anatase and rutile phase.

Enhanced Property of Thin Cuprous Oxide Film Prepared through Green Synthetic Route

Thin cuprous oxide films have been prepared by chemical vapor deposition(pulsed spray evaporation-chemical vapor deposition)method without post-treatment.The synthesis of cuprous oxide was produced by applying a water strategy effect.Then,the effect of water on the morphology,topology,structure,optical properties and surface composition of the obtained films has been comprehensively investigated.The results reveal that a pure phase of Cu2O was obtained.The introduction of a small quantity of water in the liquid feedstock lowers the band gap energy from 2.16 eV to 2.04 eV.This finding was mainly related to the decrease of crystallite size due to the effect of water.The topology analyses,by using atomic force microscope,also revealed that surface roughness decreases with water addition,namely more uniform covered surface.Moreover,theoretical calculations based on density functional theory method were performed to understand the adsorption and reaction behaviors of water and ethanol on the Cu2O thin film surface.Formation mechanism of the Cu2O thin film was also suggested and discussed.

Effect of diffraction on the ultrasonic velocity measuredby the pulse interference method in VHF range

The effect of diffraction on the ultrasonic velocity measured by the pulse interference method has been investigated in VHF range theoretically and experimentally. Two silicate glasses are taken as the specimens, their frequency dependences of longitudinal velocities are measured in the frequency range of 50-350 MHz, and the phase advances of ultrasonic signals caused by diffraction effect are calculated using A. O. Williams' theoretical expression. For the velocity error due to diffraction effect, the experimental results are in good agreement with the theoretical prediction. It has been shown that the velocity error due to diffraction effect is directly proportional to dθ21 (f)/df, whereθ21 (f) is the phase advances difference between the two partial reflection signals used in velocity measurement and f is the ultrasonic frequency.

Method based on broadband compressed pulse superposition to measure properties of underwater acoustic materials

A method is proposed for the measurements of the performances of underwater acoustic finite sized large area material samples in a free field by using broadband pulse compression technique. As the result of which, the low-frequency cutoff of the standard tests is obviously reduced, and the broadband measurements are also realized. The experimental system provides measurements of complex reflection and transmission coefficients at continuous frequency points. From the data one can obtain the following acoustic parameters: echo reduction and insertion loss, absorption and attenuation coefficients, etc. The measurements are performed for two actual panels with the size 1 m x 1 m in the frequency range from 2-20 kHz.

Experimental study on the multiscale scattering of high-velocity heterogeneous bodies

There are complex heterogeneous entities in the underground medium,and the heterogeneous scale has a substantial impact on wave propagation.In this study,we used a set of 11 samples of glass beads as high-velocity heterogeneous bodies to evaluate the impact of such heterogeneous bodies on the propagation of P-wave.We vary the heterogeneous scale by changing the diameter of the glass beads from 0.18 to 11 mm while keeping the same volume proportion(10%)of the beads for the set of 11 samples.The pulse transmission method was used to record measurements at the ultrasonic frequencies of 0.34,0.61,and 0.84 MHz in the homogeneous matrix.The relationship between P-wave fi eld features and heterogeneity scale,P-wave velocity,and the multiple of the wave number and heterogeneous scale(ka)was observed in the laboratory,which has sparked widespread interest and research.Heterogeneous scale affects P-wave propagation,and its wave field changes are complex.The waveform,amplitude,and velocity of the recorded P-waves correlate with the heterogeneous scale.For the forward scattering while large-scale heterogeneities,noticeable direct and diff racted waves are observed in the laboratory,which indicates that the infl uence of direct and diff racted waves cannot be ignored for large-scale heterogeneities.The relationship between velocity and ka shows frequency dependence;the reason is that the magnitude of change in velocity caused by wave number is diff erent from that caused by heterogeneous scale.According to the change in the recorded waveform,amplitude variation,or the relationship between the velocity measured at diff erent frequencies and the heterogeneous scale,the identifi ed turning points of the ray approximation are all around ka=10.When ka is less than 1,the velocity changes slowly and gradually approaches the eff ective medium velocity.The ray velocity measured for heterogeneous media with large velocity perturbations in the laboratory is signifi cantly smaller than the velocity predicted by the perturbation theory.

Strontium doped electrospinning fiber membrane with antibacterial and osteogenic properties prepared by pulse electrochemical method

The osteogenic differentiation and new bone formation are commonly delayed by bacterial infection of orthopedic implants,which is urgent to be resolved quickly in the clinic.The current paper prepared a strontium-doped elec-trospinning fiber membrane with antibacterial and osteogenic properties by pulse electrochemical method.Poly-lactic acid/hydroxyapatite(PLLA/HA)composite fiber substrate was fabricated by electrospinning technology,and strontium doped SrHA/Cu/Polypyrrole(PPy)composite coating was constructed with pulse electrodeposi-tion method on its surface.The strontium doping technique,degradation of Sr^(2+)and Cu^(2+),cellular compatibility,and the antibacterial activity of the fiber membrane were examined.The results revealed that the deposition of phosphorus and calcium on composite fiber was the highest,indicating good biological activity.The release of Sr^(2+)and Cu^(2+)was stable and gradual due to the modulation of PPy.The composite fiber presented excellent antibacterial performance and the antibacterial rate was close to 100%against Staphylococcus aureus and Es-cherichia coli.Furthermore,it is conducive to the adhesion,spread,and proliferation of vascular endothelial cells and osteoblasts,namely outstanding osteogenesis and angiogenesis abilities.In conclusion,the multifunctional PLLA/HA@SrHA/Cu/PPy composite fiber membrane with good antibacterial and osteogenic activity by electro-spinning technology and pulsed electrochemical deposition method provides an effective strategy for the poor bone healing of infected bone defects.

Effect of ballistic electrons on ultrafast thermomechanical responses of a thin metal film

The ultrafast thermomechanical coupling problem in a thin gold film irradiated by ultrashort laser pulses with different electron ballistic depths is investigated via the ultrafast thermoelasticity model. The solution of the problem is obtained by solving finite element governing equations. The comparison between the results of ultrafast thermomechanical coupling responses with different electron ballistic depths is made to show the ballistic electron effect. It is found that the ballistic electrons have a significant influence on the ultrafast thermomechanical coupling behaviors of the gold thin film and the best laser micromachining results can be achieved by choosing the specific laser technology（large or small ballistic range）.In addition, the influence of simplification of the ultrashort laser pulse source on the results is studied, and it is found that the simplification has a great influence on the thermomechanical responses, which implies that care should be taken when the simplified form of the laser source term is applied as the Gaussian heat source.

A Novel Particle Filtering Method for Estimation of Pulse Pressure Variation during Spontaneous Breathing

The first automatic algorithm was designed to estimate the pulse pressure variation (PPVPPV) from arterial blood pressure (ABP) signals under spontaneous breathing conditions. While currently there are a few publicly available algorithms to automatically estimate PPVPPV accurately and reliably in mechani-cally ventilated subjects, at the moment there is no automatic algorithm for estimating PPVPPV on sponta-neously breathing subjects. The algorithm utilizes our recently developed sequential Monte Carlo method (SMCM), which is called a maximum a-posteriori adaptive marginalized particle filter (MAM-PF). The performance assessment results of the proposed algorithm on real ABP signals from spontaneously breath-ing subjects were reported.

A new method and instrument for accurately measuring interval between ultrashort pulses

Using second-order autocorrelation conception, a novel method and instrument for accurately measuring interval between two linearly polarized ultrashort pulses with real time were presented. The experiment demonstrated that the measuring method and instrument were simple and accurate (the measurement error < 5 fs). During measuring, there was no moving element resulting in dynamic measurement error.

Improvement of the Pulsed Photothermal Technique for the Measurement of the Convective Heat Transfer Coefficient

The present study concerns the measurement of the convective heat transfer coefficient on the solid-fluid interface by the pulsed photothermal method.This non-intrusive technique is apphed for the measurement of the local heat transfer coefficients in cooling of a rectangular slab that simulates an electronic component.The heat transfer coefficient is deduced from the evolution of the transient temperature induced by a sudden deposit of a luminous energy on the front face of the slab.In order to draw up the heat transfer cartography by a non-destructive tool, the infrared thermography has been used.Two inverse techniques for the identification of the heat transfer coefficient are presented here.The first one is based on the assumption that heat transfer coefficient remains constant during the pulsed experiment,and the second one considered it variable in space and time.The temporal and spatial evolutions are expressed as a constant heat transfer coefficient(h_0)multiplied by a function of time and space f(x,t).The function f is deduced from the resolution of the conjugated convection-conduction problem,by a control volume technique for the case of thermally thick sample.The results are given for different air velocities and deflection angles of the flow.

Review of High Voltage Direct Current Cables

Increased renewable energy integration and international power trades have led to the construction and development of new HVDC transmission systems.HVDC cables,in particular,play an important role in undersea power transmission and offshore renewable energy integration having lower losses and higher reliability.In this paper,the current commercial feasibility of HVDC cables and the development of different types of HVDC cables and accessories are reviewed.The non-uniform electric field distribution caused by the applied voltage,temperature dependent conductivity,and space charge accumulation is briefly discussed.Current research in HVDC cable for higher operation voltage level and larger power capacity is also reviewed with specific focus on the methodologies of space charge suppression for XLPE extruded cables.

Space Charge Characteristics of Oil-paper Insulation in the Electro-thermal Aging Process

High electric field and temperatures can result in electrical property degradation of oil-paper insulation and accelerate its aging process.This paper describes the regulation of space charge in the process of electro-thermal aging.Electric field distortion and differences in characteristic parameters during electro-thermal aging are analyzed,along with the effects of electro-thermal aging on space charge from the perspective of trap energy.High temperature and an electric field are used to accelerate the aging of oil-paper,and space charge characteristics are measured using the pulsed electro-acoustic(PEA)method throughout the electro-thermal aging.Based on results obtained,it can be concluded that homo-charge injection occurs at the anode and the type of the charge injection at the cathode varies throughout the electro-thermal aging;the decrease of permittivity during aging allows for space charge injection to take place;growth of trap depth makes the space charge accumulate in the middle of the sample;and space charge accumulation after electro-thermal aging results in inner electric field distortion,which leads to large current and decreased breakdown in voltages.

Relationship between space charge and effective pore size of nanoporous electrode in electric double-layer capacitor

The space-charge distributions of electric double-layer capacitors （EDLCs）, which are energy storage devices, were examined with the pulsed electroacoustic （PEA） method. It was found that the experimental results could be influenced by the reflection and penetration of sound waves when the space-charge dis- tributions of EDLCs were measured with the PEA method. This is because EDLCs have a five-layer structure consisting of three materials （aluminum, cellulose, and activated carbon）. We calculated the reflection wave components that influenced the charge density through the acoustic impedance and the relative permittivity of the materials. In this way, we found that the changes in the space-charge distributions of EDLCs and their charge characteristics corresponded closely. We determined that measuring the space- charge distributions with the PEA method was effective for evaluating the charge accumulation of EDLCs. In this study, a polarized electrode was prepared for use in EDLCs. The ratio of the surface area to the average pore diameter of the polarized electrode was measured with the nitrogen adsorption method at 77 K. The relationship between the ratio of the surface area to the average pore size and the space-charge distributions of EDLCs is also discussed in this paper.