Operation Mode on Pulse Modulation in Atmospheric Radio Frequency Glow Discharges

The discharge operation regime of pulse modulated atmospheric radio frequency （RF） glow discharge in helium is investigated on the duty cycle and frequency of modulation pulses. The characteristics of radio frequency discharge burst in terms of breakdown voltage, alpha（s）- gamma（γ） mode transition voltage and current are demonstrated by the discharge current voltage characteristics. The minimum breakdown voltage of RF discharge burst was obtained at the duty cycle of 20% and frequency of 400 kHz, respectively. The α-γ mode transition of RF discharge burst occurs at higher voltage and current by reducing the duty cycle and elevating the modulation frequency before the RF discharge burst evolving into the ignition phase, in which the RF discharge burst can operate stably in the γ mode. It proposes that the intensity and stability of RF discharge burst can be improved by manipulating the duty cycle and modulation frequency in pulse modulated atmospheric RF glow discharge.

An Improved Submodule Unified Pulse Modulation Scheme for a Hybrid Modular Multilevel Converter

This paper presents an improved submodule unified pulse width modulation(SUPWM)scheme for a hybrid modular multilevel converter(MMC)composed of half-bridge submodules(HBSMs)and full-bridge submodules(FBSMs).The proposed SUPWM scheme can achieve an output voltage of(2N+1)(where N is the number of submodules in each arm)levels,which is the same as that of the carrier-phase-shifted PWM(CPSPWM)scheme.Meanwhile,the proposed SUPWM scheme can alleviate the uneven loss distributions between the left leg and right leg in FBSMs of the hybrid MMC.Moreover,the capacitor voltages of the sub-modules can be well balanced without complicated closed-loop voltage balancing controllers.The validity of the proposed SUPWM scheme is verified by both the simulated and experimental results.

Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.

Linear and nonlinear characteristics of time-resolved photoluminescence modulation by terahertz pulse

The linear and nonlinear characteristics of time-resolved photoluminescence （PL） of n-type bulk semiconductor GaAs modulated with terahertz （THz） pulse are studied by using an ensemble Monte Carlo （EMC） method. In this paper the center energy valley （Г valley） electron concentration changes with the pulse delay time, sampling time and the outfield are mainly discussed. The results show that the sampling time and the THz field should exceed certain thresholds to effectively excite photoluminescence quenching （PLQ）. Adopting a direct current （DC） field makes the sampling time threshold shortened and the linear range of THz field-modulation PL expanded. Moreover, controlling the sampling time and the outfield intensity can improve the linear quality： with forward time, the larger outfield is used; with backward time, the smaller outfield is used. This study can provide a theoretical basis of THz field linear modulation in a larger range for new light emitting devices.

Kinetic simulation of the transition from a pulse-modulation microwave discharge to a continuous plasma

The generation of a very strong peak current in the first period(PCFP)in a pulse-modulated microwave discharge has been discussed in previous studies.In this paper we focus on the transition process from a pulsed discharge to a fully continuous one driven by the pulsed microwave power source by means of a kinetic model.The computational results show that by increasing the duty cycle or voltage modulation rate(VMR).the discharge eventually becomes fully continuous and PCFP can no longer he observed.In the transition process,the distributions of the electric field,electron energy probability function(EEPF)and plasma density are discussed according to the simulation data,showing different discharge structures.The simulations indicate that many high-energy electrons with electron energy larger than 20eV and low-energy electrons with electron energy less than 3eV could he generated in a pulsed microwave discharge,together with a reversal electric field formed in the anode sheath when PCFP occurs.However,only medium-energy electrons could be observed in a fully continuous discharge.Therefore,by investigating the transition process the pulse-modulated microwave discharges can be further optimized for plasma applications at atmospheric pressure.

Efficient combination and enhancement of high-power mid-infrared pulses in plasmas

High-power intense optical sources in the mid-to-long wavelength infrared region are very attractive for a wide range of fields from fundamental research to materials science and biology applications.However,there are still significant challenges in extending long-wavelength infrared pulses into the relativistic regime using conventional optical techniques.Here,based upon a new type of plasma-based optical method,we present an efficient scheme capable of combining several high-power long-wavelength infrared laser pulses into one single,more intense pulse,thus bringing the intensity of the output pulse to the relativistic regime.Such intense infrared pulses will open up new possibilities for strong-field physics and ultrafast applications.Furthermore,this is beneficial to understand the underlying physics and nonlinear processes of modulation,propagation and energy transfer of high-power intense laser pulses in plasmas.

CONTROL STRATEGY FOR ELECTRO-HYDRAULIC POSITION SERVO SYSTEM WITH GENERALIZED PULSE CODE MODULATION

A hybrid control strategy has been designed and developed for the electro-hydraulic posi-tion servo control system with generalized Pulse code modulation （GPCM）, which is suitable for the area where the work condition is poor and a large flow rate is required. It is difficult to control the GPCM system because the system is discrete. With consideration of the stability and speediness of the GPCM position servo control system, a control strategy is developed through the theoretical and ex-perimental analyses. The control strategy integrates the merits of Bang-Bang control, PID control and fuzzy control. With this hybrid control strategy, the electro hydraulic control system has good per-formances, and the servo control is carried out with GPCM through on-off valves.

Ultra-low power anti-crosstalk collision avoidance light detection and ranging using chaotic pulse position modulation approach

A novel concept of collision avoidance single-photon light detection and ranging（LIDAR） for vehicles has been demonstrated, in which chaotic pulse position modulation is applied on the transmitted laser pulses for robust anti-crosstalk purposes. Besides, single-photon detectors（SPD） and time correlated single photon counting techniques are adapted, to sense the ultra-low power used for the consideration of compact structure and eye safety. Parameters including pulse rate, discrimination threshold, and number of accumulated pulses have been thoroughly analyzed based on the detection requirements, resulting in specified receiver operating characteristics curves. Both simulation and indoor experiments were performed to verify the excellent anti-crosstalk capability of the presented collision avoidance LIDAR despite ultra-low transmitting power.

Modeling and Analysis of Pulse Skip Modulation

The state space average model and the large signal models of Pulse Skip Modulation （PSM） mode are given in this paper. Farther more, based on these models and simulations of PSM converter circuits, the analysis of the characteristics of PSM converter is described in this paper, of which include efficiency, frequency spectrum analysis, output voltage ripple, response speed and interference rejection capability. Compared with PWM control mode, PSM converter has high efficiency, especially with fight loads, quick response, good interference rejection and good EMC characteristic. Improved PSM slightly, it could be a kind of good independent regulating mode during the whole operating process for a DC-DC converter. Finally, some experimental results are also presented in this paper.

Performance analysis of a low-complexity nonorthogonal multiple access scheme in visible light communication downlinks using pulse modulations

Although Successive Interference Cancellation(SIC)decoding is widely adopted in Nonorthogonal Multiple Access(NOMA)schemes for the recovery of user data at acceptable complexity,the imperfect SIC would cause Error Propagation(EP),which can severely degrade system performance.In this work,we propose an SIC-free NOMA scheme in pulse modulation based Visible Light Communication(VLC)downlinks,including two types of users with different data rate requirements.Low bit-rate users adopt on-off keying,whereas high bit-rate ones use Multiple Pulse Position Modulation(MPPM).The soft decision decoding scheme is exploited by high bit-rate users to decode MPPM signals,which could fundamentally eliminate the detrimental effect of EP;the scheme is also easier and faster to execute compared with the conventional SIC decoding scheme.Expressions of the symbol error rate and achievable data rate for two types of users are derived.Results of the Monte Carlo simulation are provided to confirm the correctness of theoretical results.

Comparison of performance between bipolar and unipolar double-frequency sinusoidal pulse width modulation in a digitally controlled H-bridge inverter system

By deriving the discrete-time models of a digitally controlled H-bridge inverter system modulated by bipolar sinu- soidal pulse width modulation （BSPWM） and unipolar double-frequency sinusoidal pulse width modulation （UDFSPWM） respectively, the performances of the two modulation strategies are analyzed in detail. The circuit parameters, used in this paper, are fixed. When the systems, modulated by BSPWM and UDFSPWM, have the same switching frequency, the stabil- ity boundaries of the two systems are the same. However, when the equivalent switching frequencies of the two systems are the same, the BSPWM modulated system is more stable than the UDFSPWM modulated system. In addition, a convenient method of establishing the discrete-time model of piecewise smooth system is presented. Finally, the analytical results are confirmed by circuit simulations and experimental measurements.

Pulse Propagation with Self-Phase Modulation in Nonlinear Chiral Fiber and Its Applications

From Maxwell＇s equations and Post＇s formalism, a generalized chiral nonlinear Schr6dinger equation （CNLSE） is obtained for the nonlinear chiral fiber. This equation governs light transmission through a dispersive nonlinear chiral fiber with joint action of chirality in linear and nonlinear ways. The generalized CNLSE shows a modu- lation of chirality to the effect of attenuation and nonlinearity compared with the case for a conventional fiber. Simulations based on the split-step beam propagation method reveal the role of nonlinearity with cooperation to chirality playing in the pulse evolution. By adjusting its strength the role of chirality in forming solitons is demonstrated for a given circularly polarized component. The application of nonlinear optical rotation is also discussed in an all-optical switch.

Realization of Space Vector Pulse Width Modulation Method Based on DSP

In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving working time of adjacent vector and the method of generate space voltage vector were introduced. The experiment to the inverter which consists of IGBT proves that SVPWM centrol algorithm can reduce harmonic effectively, it is beneficial to enhancing the utilization rate of voltage source inverter direct current power supply.

PRI modulation recognition and sequence search under small sample prerequisite

Pulse repetition interval(PRI)modulation recognition and pulse sequence search are significant for effective electronic support measures.In modern electromagnetic environments,different types of inter-pulse slide radars are highly confusing.There are few available training samples in practical situations,which leads to a low recognition accuracy and poor search effect of the pulse sequence.In this paper,an approach based on bi-directional long short-term memory(BiLSTM)networks and the temporal correlation algorithm for PRI modulation recognition and sequence search under the small sample prerequisite is proposed.The simulation results demonstrate that the proposed algorithm can recognize unilinear,bilinear,sawtooth,and sinusoidal PRI modulation types with 91.43% accuracy and complete the pulse sequence search with 30% missing pulses and 50% spurious pulses under the small sample prerequisite.

Recognition of dynamically varying PRI modulation via deep learning and recurrence plot

Recognition of pulse repetition interval(PRI)modulation is a fundamental task in the interpretation of radar intentions.However,the existing PRI modulation recognition methods mainly focus on single-label classification of PRI sequences.The prerequisite for the effectiveness of these methods is that the PRI sequences are perfectly divided according to different modulation types before identification,while the actual situation is that radar pulses reach the receiver continuously,and there is no completely reliable method to achieve this division in the case of non-cooperative reception.Based on the above actual needs,this paper implements an algorithm based on the recurrence plot technique and the multi-target detection model,which does not need to divide the PRI sequence in advance.Compared with the sliding window method,it can more effectively realize the recognition of the dynamically varying PRI mo dulation.

Improved Protein Transfer Efficiency and Signal Intensity in BlotMan Using Pulse Width Modulation

BlotMan is a protein blotting device that allows generating multiple membranes from a single polyacrylamide gel. To transfer all proteins uniformly with the same efficiency regardless of protein size, BlotMan employs pulse-width-modulated (PWM) voltage that applies a higher average voltage to a larger protein species. BlotMan can be controlled not only by its custom-made interface but also by a smart phone via Bluetooth technology. In this study, we examined effects of PWM signals (50%, 60%, and 80% duty cycle) on transfer efficiency and signal intensity in comparison to a constant voltage signal (100% duty cycle). The result revealed that in response to the same average voltage of 150 V, a lower duty cycle with a higher maximum voltage increased transfer efficiency as well as sharpness of transferred proteins. We validated BlotMan’s capability using a chondrosarcoma cell line (SW1353 cells) and a breast cancer cell line (MDA-MB231 cells) in response to antitumor chemical agents. BlotMan successfully generated 5 membranes from a single gel and detected 5 protein species such as c-Src, eukaryotic translation initiation factor 2 alpha (eIF2), phosphorylated eIF2, lamin B, and actin. Collectively, we demonstrated herein that BlotMan reduces an amount of protein samples by generating multiple membranes from a single gel and improving signal intensity with PWM voltage signals.

Capacitor Pattern H-Bridge Multilevel Inverter (CPHMLI) Using Phase Diposition Pulse Width Modulation for Grid Applications

This work presents an implementation of an innovative single phase multilevel inverter using capacitors with reduced switches. The proposed Capacitor pattern H-bridge Multilevel Inverter (CPHMLI) topology consists of a proper number of Capacitor connected with switches and power sources. The advanced switching control supplied by Pulse Width Modulation (PDPWM) to attain mixed staircase switching state. The charging and discharging mode are achieved by calculating the voltage error at the load. Furthermore, to accomplish the higher voltage levels at the output with less number of semiconductors switches and simple commutation designed using CPHMLI topology. To prove the performance and effectiveness of the proposed approach, a set of experiments performed under various load conditions using MATLAB tool.

A Novel Pulse Density Modulation with Semi-bridgeless Active Rectifier in Inductive Power Transfer System for Rail Vehicle

In this paper,a novel pulse density modulation(PDM)with semi-bridgeless active rectifier(S-BAR)in inductive power transfer(IPT)system for rail vehicle is proposed.It is to reduce switching losses of the active rectifier in pickups.In the control method,the insulated-gate bipolar transistors(IGBTs)in the S-BAR are controlled by synchronous PDM signals,so that zero-voltage switching(ZVS)and zero-current switching(ZCS)can be achieved in the whole output power range.The output power is regulated by changing the pulse density(PD)of the S-BAR since the it is almost linear proportional with the PD in high quality factor of pickup side.The communication device between the primary side and pickup side is not necessary anymore.The detailed theoretical analyses of the PDM method are provided,and its advantages are shown in a 7.5kW IPT prototype for rail vehicle.The experimental results are presented to verify the analysis and demonstrate the performance.The overall efficiency of the system by PDM control is 74.2%which is improved by 4%compared with phase shift(PS)control at light load.