Analysis of Quenching Resistor Effect to Improve Stability of TIA Circuit for APD-A Secondary Publication

In this paper,since the Avalanche Photo Diode(APD)for Light-to-Voltage LTV conversion uses a high voltage in the operating range unlike other Photo Diodes(PD),the quenching resistor must be connected in series to prevent overcurrent when using the Transimpedance Amplifier(TIA).In such a case,quenching resistance may affect the transfer function of the TIA circuit,resulting in serious stability.Therefore,in this paper,by analyzing the effect of APD quenching resistance on the voltage and current loop transfer function of TIA,we proposed a loop analysis and a method for determining the quenching resistance value to improve stability.A TIA circuit with quenching resistance was designed by the proposed method and its operational stability was verified through simulation and chip fabrication.

Discussion on the Free Quenching Heat Treatment Process of Automotive Leaf Springs

Free quenching of automotive leaf springs is a new technology that has gradually started to be applied in the industry in China in recent years.Only a few manufacturers are applying it in the industry.Through more than half a year of on-site practice,the changes in the hot forming of spring plates before free quenching have been explored,and finally a heat treatment process that meets the production requirements of our company has been developed,achieving normal production.

Influence of quenching medium on the dendrite morphology,hardness,and tribological behaviour of cast Cu-Ni-Sn spinodal alloy for defence application

Cu-Ni-Sn spinodal alloys(Spinodal bronze)are potential materials with robust applications in components associated with defence applications like bearings,propellers,bushes,and shafts of heavily loaded aircraft,off-road vehicles,and warships.This paper presents a comparative study using water,Brine solution,and SAE 40 oil as the quenching media in regular bronze(Cu-6Sn)and spinodal bronze(Cu-9Ni-6Sn)alloys.Morphological analysis was conducted by optical microscopy,transmission electron microscopy(TEM),and X-ray diffraction technique(XRD)on bronze and spinodal bronze samples immersed in the three different quenching media to understand the grain size and hardness values better.Tribological analysis was performed to analyze the effect of quenching media on the wear aspects of bronze and spinodal bronze samples.The hardness value of the brine-aged spinodal bronze samples was as high as 320 Hv,and the grain size was very low in the range of 60μm.A quantitative comparison between brine-aged regular bronze and brine-aged spinodal bronze showed that the hardness(Hv)was almost 80%higher for brine-aged spinodal bronze.Further,the grain size was approximately 30%finer for spinodal bronze when compared with regular bronze.When the load was increased in spinodal bronze samples,there was an initial dip in wear rate followed by a marginal increase.There was a steady increase in friction coefficient with a rise in load for brine-aged regular bronze and spinodal bronze samples.These results indicate that brine solution is the most effective quenching medium for cast Cu-Ni-Sn spinodal alloys.

Residual stress with asymmetric spray quenching for thick aluminum alloy plates

Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.

Influence of two distinct quenching end-temperatures on phase development and mechanical properties in QP980 steel

Bainite microstructures have become increasingly attractive for the development of advanced high-strength steel owing to their balanced strength-plasticity properties.In this study, the final microstructure and mechanical properties of a quenching and partitioning(QP) steel sample after two distinct QP processes were analyzed.The results reveal that martensite transformation after quenching resulted in a lathed morphology with higher yield strength and hole expansion ratio.In contrast, bainite transformation after quenching resulted in the formation of a blocky microstructure composed of bainitic ferrite retained austenite and nanoscale precipitates during the subsequent phase transformation at a higher temperature.This kind of final microstructure is beneficial to the elongation of QP steel but detrimental to the hole expansion ratio.

Development and Application of Multi-phase Nitrides Bonded Silicon Carbide Lintel Blocks for Dry Quenching Furnaces

Multi-phase nitrides bonded silicon carbide lintel blocks were prepared using industrial SiC(SiC≥98 mass%,3-0.5,≤0.5 and≤0.044 mm),Si powder(Si≥98 mass%,≤0.044 mm),and SiO2 micropowder(SiO2≥96 mass%,d50=0.15 pm)as raw materials,and calcium lignosulfonate as the additive,batching,mixing,and molding on a vibration pressure molding machine,drying and then firing at 1420℃for 10 h in high-purity N2.The apparent porosity,the bulk density,the cold modulus of rupture,the hot modulus of rupture,and the linear expansion coefficient of the samples were tested.The phase composition and the microstructure of the samples at different nitriding depths(50,100,and 150 mm)were analyzed by XRD and SEM.The field application effects of the blocks were studied.The results show that:(1)the multi-phase nitrides bonded silicon carbide refractories can dynamically adjust their own phase composition and minimize structural and thermal stresses,improving the service life of key parts of dry quenching furnaces;(2)calcium lignosulfonate can improve the nitriding micro-environment of multi-phase nitrides bonded silicon carbide lintel blocks,successfully increasing the effective nitriding thickness of the blocks to 300 mm;(3)Sinosteel LI RR provides a unique concept in the design of materials and block types as well as the stable and scientific overall structure,promoting the industrialization process of dry quenching furnaces with long service life in China.

Effect of quenching and tempering processes on properties and microstructure of G115 steel

The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the properties and microstructure of G115 steel was explored.The samples that were quenched and tempered twice had a higher tensile strength at room temperature and 650 ℃,and the impact energy was significantly improved.The strength and impact energy increased in proportion to the increase in the first quenching temperature.The microstructure differences between the single and double quenched and tempered samples were examined using metallographic microscopy and scanning electron microscopy.The grain size of the double quenched and tempered samples was finer than that of the single quenched and tempered samples, and the tempered martensite lath is more visible, as are the carbides and other precipitates, which are finer and more uniformly distributed.As the first quenching temperature increased, the grains became coarser but more uniform.

Visualization of Vapor Film Collapse Behavior with Complexity on Quenching Process by Cellular Automaton

The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required these days,it is necessary to predict the quality of heat treatment by CAE(Computer Added Engineering),shorten the product development period.The calculation of the vapor film collapses in a simple and practical time in order to improve the product performance.However,in the past,in order to formulate the vapor film collapse on a simulation,it was necessary to perform a very large amount of computational calculation CFD(computational fluid dynamics),which was a problem in terms of computer resources and the model of vapor film collapse.In addition,this phenomenon has a complexity behavior of the phenomenon in iterative processing,which also complicates the calculation.In this study,the vapor film collapse phenomenon is easily visualized using self-organized cellular automaton simulation which includes the phenomena of“vapor film thickness and its fluctuation”,“flow disturbance”,“surface step of workpiece”,and“decrease of cooling due to r shape of surface”.The average cooling state and repeated fluctuations of the cooling state were reproduced by this method.

Non-simultaneous quenching for a slow diffusion system coupled at the boundary

This paper deals with the quenching behavior of positive solutions to the Newton filtration equations coupled with boundary singularities.We determine quenching rates for non-simultaneous quenching at first,and then establish the criteria to identify the simultaneous and non-simultaneous quenching in terms of the parameters involved.

Effects of Quenching Process on Mechanical Properties and Microstructure of High Strength Steel

The effects of direct quenching and tempering （DQ-T） process and conventional reheat quenching and tempering （RQ-T） processes on mechanical properties and microstructure of high strength steel were investigated. The DQ process was found to enhance the hardenability of steel effectively. The tensile strength and yield strength of DQ specimen was 975 MPa and 925 MPa respectively, which were higher than those of RQ specimen＇s of 920 MPa and 871 MPa. In contrast, low temperature toughness （-40 ℃, AKV） of DQ-T specimen （124 J） was generally inferior to that of RQ-T specimen （156 J）. The direct quenching temperature was one of the potential process parameters to determine strength/toughness balance of steel manufactured by DQ process. The experimental results showed that excellent strength/toughness balance was obtained when the specimens was quenched at temperature in the range of 850-910 ℃. The yield strength and impact energy （-40 ℃） of DQ steel decreased significantly with increasing of quenching temperature, although the tensile strength was nearly stable.

Effect of quenching temperature on the microstructure of Si-containing steel during quenching and partitioning

This study aims to investigate the effect of the 1-step quenching and partitioning （Q＆P） process on the microstructure and the resulting Vicker＇ s hardness of 0.3C-1.5Si-1.5Mn steel by using in-situ dilatometry ,optical microscopy （ OM ）, scanning electron microscopy （ SEM ）, X-ray diffractometry （ XRD ）, and Vicker ＇ s hardness measurement. Systematic analyses indicate that the microstructure of the specimens quenched and partitioned at 150℃ ,200 ℃ ,250℃ ,and 300℃ mainly comprises lath martensite and retained austenite. The dilatometry curve of the specimen partitioned at 150℃ is presumably ascribed to the formation of isothermal martensite. In the early stages of partitioning at 200℃,the nearly unchanged dilatation curve is closely related to the synergistic effect of isothermal martensite formation and transitional epsilon carbide precipitation. In the later stages of partitioning at 200 ℃ ,the slight increase in the dilatation curve is due to the continuous isothermal martensite formation. With further increase in partitioning temperature to 250℃, the dilatation increases gradually up to 3600 s, which is related to carbon partitioning and lower bainite formation. Partitioning at a higher temperature of 300 ℃ causes a rapid increase in the dilatation curve during the initial stages, which subsequently levels off upon prolonging the partitioning time. This is mainly attributed to the rapid diffusion of carbon from athermal martensite to retained austenite and continuous formation of lower bainite.

Interface Migration between Martensite and Austenite during Quenching and Partitioning (Q&P) Process

An Fe-0.2C-1.5Si-1.67Mn steel was subjected to quenching and partitioning （Q＆P） process, and the interface migration between martensite and austenite at an elevated partitioning temperature was observed. The interface migration is excluded in constrained paraequilibrium （CPE） model. Based on ＂endpoint＂ predicted by CPE model the thermodynamic condition of interface migration is analyzed, that is, the difference in the chemical potential of iron in both ferrite （martenisite） and austenite produces the driving force of the iron atoms to migrate from one phase to the other phase. In addition, the interface migration can change the austenite fraction; as a result, the austenite fraction at partitioning temperature may be higher than that at quenching temperature through the interface migration, but this phenomenon cannot be explained by CPE model.

Numerical Simulation on Carburizing and Quenching of Gear Ring

The carburizing process of the gear ring was simulated by taking into account the practical carburizing and quenching techniques of the gear ring and by solving the diffusion equation. The carbon content distribution in the carburized layer was obtained. Based on the results, the quenching process of the gear ring was then simulated using the metallic thermodynamics and FEM： it was found that the carburization remarkably affects the quenching process. Microstructures and stress distributions of the gear ring in the quenching process were simulated, and the results are confirmed by experiments.

The Mechanisms and Applications of Quorum Sensing(QS) and Quorum Quenching(QQ)

Quorum sensing(QS)is a regulatory system that regulates the behavior of microbial populations by sensing the concentration of signal molecules that are spontaneously produced and released by bacteria.The strategy of blocking the QS system and inhibiting the production of virulence factors is termed as quorum quenching(QQ).This strategy attenuates virulence without killing the pathogens,thereby weakening the selective pressure on pathogens and postponing the evolution of QQ-mediated drug resistance.In recent years,there have been significant theoretical and practical developments in the field of QS and QQ.In particular,with the development and utilization of marine resources,more and more marine microbial species have been found to be regulated by these two mechanisms,further promoting the research progress of QS and QQ.In this review,we described the diversity of QS signals and QS-related regulatory systems,and then introduced mechanisms related to QS interference,with particular emphasis on the description of natural QQ enzymes and chemicals acting as QS inhibitors.Finally,the exploitation of quorum sensing quenchers and the practical application of QQ were introduced,while some QQ strategies were proposed as promising tools in different fields such as medicine,aquaculture,agriculture and biological pollution prevention areas.

Changes in the thermodynamic properties of alkaline granite after cyclic quenching following high temperature action

During the development of hot dry rock,the research on thermal fatigue damage caused by thermal shock of cold and heat cycles is the basis that ensures the long-term utilization of geothermal resources,but there are not enough relevant studies at present.Based on this,the thermal damage tests of granite at different temperatures(250,350,450°C)and quenching cycles(1,5,10,15 cycles)were carried out.Preliminary reveals the damage mechanism and heat transfer law of the quenching cycle effect on hot dry rock.The results show that with the increase of temperature and cycles,the uneven thermal expansion of minerals and the thermal shock caused by quenching promote the crack development of granite,resulting in the decrease of P-wave velocity,thermal conductivity and uniaxial compressive strength of granite.Meanwhile,the COMSOL was used to simulate the heat transfer of hot dry rock under different heat treatment conditions.It concluded that the increase in the number of quenching cycles reduced the heat transfer capacity of the granite,especially more than 10 quenching cycles,which also reflects that the thermal fatigue damage leads to a longer time for the temperature recovery of the hot dry rock mass.In addition,the three-dimensional nonlinear fitting relationship among thermal conductivity,temperature and cycle number was established for the first time,which can better reveal the change rule of thermal conductivity after quenching thermal fatigue effect of hot dry rock.The research results provide theoretical support for hot dry rock reservoir reconstruction and production efficiency evaluation.

COUPLED NUMERICAL SIMULATION ON COLD ROLLER'S TEMPERATURE FIFLD-PHASE TRANSFORMATION - STRESS FIELD DURING ITS QUENCHING PSOCESS

Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.

Design of Quenching Process for Large-sized AISI P20 Steel Block Used as Plastic Die

For large-sized AISI P20 steel block used as plastic die with a thickness of more than 200 mm, appropriate quenching processes are the key to obtain much thick hardened layer. In this paper, different quenching processes of AISI P20 steel block such as oil quenching, direct water quenching, water quenching with precooling and water quenching with pre-cooling and self-tempering were numerically investigated by computer simulation based on the detailed discussion on the mathematical models of quenching processes including partial differential equations of heat transfer, thermal physical properties, latent heat, heat transfer coefficient and calculation of phase transformation, The results show that the water quenching with pre-cooling and self-tempering process can not only effectively avoid quenching cracks, but also obtain deeper harden depth than oil quenching.

DEVELOPMENT OF COMPUTER SIMULATION SOFTWAREON PHASE TRANSFORMATION DURING QUENCHING

A computer software to simulate the phase transformation during quenching is designed based on Avrami equation and Scheil additivity principle of incubation period. The isothermal transformation diagrams of supercooled austenite are described by cubic spline functions. This software is possess of a good graphic interface of Windows style, can simulate the whole process in austenite decomposition during continuous cooling. If the cooling rate was given, the fraction of various microstructures transformed of austenite decomposition during continuous cooling at any temperature can be calculated. The simulation results are checked with the quenching experiment of 45 steel. The results indicate that the simulation results are comparatively close to the experimental results.

Influence of rapid quenching on cyclic stability of La-Mg-Ni system (AB_3-type) electrode alloys

Aiming at the improvement of the cyclic stability of La-Mg-Ni system （PuNi3-type） hydrogen storage alloy, Ni in the alloy was partly substituted by Fe. The electrode alloys of La0.7Mg0.3Co0.45Ni255-xFex （x=0, 0.1, 0.2, 0.3, 0.4） were prepared by casting and rapid quenching. The influence of the quenching on cyclic stability as well as structure of the alloys was investigated in detail. The results of electrochemical measurement indicated that rapid quenching significantly improved cyclic stability. When the quenching rate rose from 0 （As-cast was defined as a quenching rate of 0 m/s） to 30 m/s, the cyclic life of Fe-free alloy （x=-0） increased from 81 to 105 cycles, and for alloy containing Fe（x=0.4）, it grew from 106 to 166 cycles at a current density of 600 mA/g. The results obtained by XRD, TEM and SEM revealed that the as-cast and quenched alloys had multiphase structures, including two major phases （La, Mg）Ni3 and LaNi5 as well as an imptLrity phase LaNi2. Rapid quenching helped the formation of an amorphous-like structure in Fe containing alloys.

Effect of lower bainite/martensite/retained austenite triplex microstructure on the mechanical properties of a low-carbon steel with quenching and partitioning process

We present a study concerning Fe-0. 176C-1.31Si-1.58Mn-0.26Al-0.3Cr （wt%） steel subjected to a quenching and partitioning （Q＆P） process. The results of scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and tensile tests demon- strate that the microstructures primarily consist of lath martensite, retained austenite, lower bainite （LB）, and a small amount of tempered martensite; moreover, few twin austenite grains were observed. In the microstrucmre, three types of retained austenite with different sizes and morphologies were observed： blocky retained austenite （-300 nm in width）, film-like retained austenite （80-120 nm in width）, and ul- tra-fine film-like retained austenite （30-40 nm in width）. Because of the effect of the retained austenite/martensite/LB triplex microstructure, the specimens prepared using different quenching temperatures exhibit high ultimate tensile strength and yield strength. Furthermore, the strength effect of LB can partially counteract the decreasing strength effect of martensite. The formation of LB substantially reduces the amount of retained austenite. Analyses of the retained austenite and the amount of blocky retained austenite indicated that the carbon content is critical to the total elongation of Q＆P steel.