The reinforced concrete(RC) structural component might suffer a great damage under close-in explosion.Different from distant explosions, blast loads generated by the close-in explosion are non-uniformly distributed on...The reinforced concrete(RC) structural component might suffer a great damage under close-in explosion.Different from distant explosions, blast loads generated by the close-in explosion are non-uniformly distributed on the structural component and may cause both local and structural failure. In this study,an experimental study was conducted to investigate the dynamic responses of RC beams under doubleend-initiated close-in explosions. The experimental results show that the distribution of blast loads generated by the double-end-initiated explosion is much more non-uniform than those generated by single-point detonation, which is caused by the self-Mach-reflection effects. A 3 D finite element model was developed and validated in LS-DYNA by employing the modified K&C model. Intensive numerical calculations were conducted to study the influences of the initiation way, scaled distance and longitudinal reinforcement ratio on the dynamic responses and failure modes of RC beams. Numerical results show that the RC beam suffers greater damage as the cylindrical explosive is detonated at its double ends than the scenario in which the cylindrical explosive is detonated at its central point. RC beams mainly suffer flexural failure and flexure-shear failure under the double-end close-in explosion, and the failure modes of RC beams change from the flexural damage to flexure-shear damage as the scaled distance or the longitudinal reinforcement ratio decreases. The direct shear failure mode is not usually observed in the double-end-initiated explosion, since the intense blast loads is basically concentrated in the midspan of RC beam, which is due to self-Mach-reflection enhancement.展开更多
Seven reinforced concrete （ RC ） beams strengthened in flexure using carbon fiber reinforced polymer （CFRP） sheets subjected to different sustaining loads were tested. The effects of initial load and load history ...Seven reinforced concrete （ RC ） beams strengthened in flexure using carbon fiber reinforced polymer （CFRP） sheets subjected to different sustaining loads were tested. The effects of initial load and load history on the ultimate strength of strengthened RC beams were examined by externally bonded CFRP sheets. The main experimental parameters included different levels of sustaining load at the time of strengthening, and load history. Experimental results show that sustaining load levels at the time of strengthening have important influences on the ultimate strength of strengthened RC beams. If the initial load is the same, the ultimate strength of RC beams strengthened with CFRP sheets is almost the same regardless of load history at the time of strengthening.展开更多
Feasibility of using pre-stressed carbon fiber plates to strengthen reinforced concrete beams was studied. Based on the characteristics of carbon fiber plates, we developed a pre-stress clamp and a device for applying...Feasibility of using pre-stressed carbon fiber plates to strengthen reinforced concrete beams was studied. Based on the characteristics of carbon fiber plates, we developed a pre-stress clamp and a device for applying the pre-stress. Contrast tests were conducted between ordinary carbon fiber plates and a pre-stressed carbon fiber plate and between secondary loaded carbon fiber plates and a concrete beam strengthened with a secondary loaded carbon fiber plate. On this basis, we analyzed the failure pattern, the width of cracks and their distribution, the cracking load, the yield load, the limit load and the relation between load and deflec- tion. The results indicate that using pre-stressed carbon fiber plates to strengthen concrete beams is feasible and effective.展开更多
Since most current seismic capacity evaluations of reinforced concrete （RC） frame structures are implemented by either static pushover analysis （PA） or dynamic time history analysis, with diverse settings of the p...Since most current seismic capacity evaluations of reinforced concrete （RC） frame structures are implemented by either static pushover analysis （PA） or dynamic time history analysis, with diverse settings of the plastic hinges （PHs） on such main structural components as columns, beams and walls, the complex behavior of shear failure at beam-column joints （BCJs） during major earthquakes is commonly neglected. This study proposes new nonlinear PA procedures that consider shear failure at BCJs and seek to assess the actual damage to RC structures. Based on the specifications of FEMA-356, a simplified joint model composed of two nonlinear cross struts placed diagonally over the location of the plastic hinge is established, allowing a sophisticated PA to be performed. To verify the validity of this method, the analytical results for the capacity curves and the failure mechanism derived from three different full-size RC frames are compared with the experimental measurements. By considering shear failure at BCJs, the proposed nonlinear analytical procedures can be used to estimate the structural behavior of RC frames, including seismic capacity and the progressive failure sequence of joints, in a precise and effective manner.展开更多
In the last two decades, the study of reinforced concrete (RC) structures elements such as bridge deck slabs, bridge girders, or offshore installations, which?are?subjected to cyclic action typically induced by seismi...In the last two decades, the study of reinforced concrete (RC) structures elements such as bridge deck slabs, bridge girders, or offshore installations, which?are?subjected to cyclic action typically induced by seismic motions has received the attention of many researchers.?Furthermore, the past two decades have witnessed rapid growth in the use of fiber-reinforced polymer (FRP) confining jackets for the strengthening/retrofit of reinforced concrete (RC) columns and beams. Moreover, several theoretical and empirical models?have been proposed for evaluating the?shear strength of beams, columns and beam-to-column joints. In this?paper, an overview of the models currently available in the scientific literature for?evaluating the?shear capacity of?beams, columns and?exterior beam-to-column joints?is reported.?Further, important practical issues which contribute in?shear strengthening of structures with different element types especially RC beams with different strengthening techniques, such as steel plate and FRP laminate are discussed.?Finally,?directions for future research based on the existing gaps of the existing works are presented.展开更多
The influence of carbon fiber reinforced plastic(CFRP)on dynamic mechanical properties of reinforced concrete(RC)beam was studied by drop hammer impact test system.The impact behaviors of beam,including failure mode,i...The influence of carbon fiber reinforced plastic(CFRP)on dynamic mechanical properties of reinforced concrete(RC)beam was studied by drop hammer impact test system.The impact behaviors of beam,including failure mode,impact force peak value and peak deflection were analyzed.The experimental results show that bonding CFRP can reduce the crack width and change the failure mode of the beam.The length of CFRP has a certain influence on the impact force and deflection,and the peak inertia force of most beams is roughly in the range of 1/2-5/6 of the peak impact force.In addition,dynamic increase factor(DIF)increases with the increase of CFRP length,and its maximum value can reach 2.11.展开更多
基金supported by the National Natural Science Foundations of China(Nos. 51622812, and 51427807)National Basic Research Program of China(No. 2015CB058003)China Postdoctoral Science Foundation(No. 2017M613379)
文摘The reinforced concrete(RC) structural component might suffer a great damage under close-in explosion.Different from distant explosions, blast loads generated by the close-in explosion are non-uniformly distributed on the structural component and may cause both local and structural failure. In this study,an experimental study was conducted to investigate the dynamic responses of RC beams under doubleend-initiated close-in explosions. The experimental results show that the distribution of blast loads generated by the double-end-initiated explosion is much more non-uniform than those generated by single-point detonation, which is caused by the self-Mach-reflection effects. A 3 D finite element model was developed and validated in LS-DYNA by employing the modified K&C model. Intensive numerical calculations were conducted to study the influences of the initiation way, scaled distance and longitudinal reinforcement ratio on the dynamic responses and failure modes of RC beams. Numerical results show that the RC beam suffers greater damage as the cylindrical explosive is detonated at its double ends than the scenario in which the cylindrical explosive is detonated at its central point. RC beams mainly suffer flexural failure and flexure-shear failure under the double-end close-in explosion, and the failure modes of RC beams change from the flexural damage to flexure-shear damage as the scaled distance or the longitudinal reinforcement ratio decreases. The direct shear failure mode is not usually observed in the double-end-initiated explosion, since the intense blast loads is basically concentrated in the midspan of RC beam, which is due to self-Mach-reflection enhancement.
文摘Seven reinforced concrete （ RC ） beams strengthened in flexure using carbon fiber reinforced polymer （CFRP） sheets subjected to different sustaining loads were tested. The effects of initial load and load history on the ultimate strength of strengthened RC beams were examined by externally bonded CFRP sheets. The main experimental parameters included different levels of sustaining load at the time of strengthening, and load history. Experimental results show that sustaining load levels at the time of strengthening have important influences on the ultimate strength of strengthened RC beams. If the initial load is the same, the ultimate strength of RC beams strengthened with CFRP sheets is almost the same regardless of load history at the time of strengthening.
文摘Feasibility of using pre-stressed carbon fiber plates to strengthen reinforced concrete beams was studied. Based on the characteristics of carbon fiber plates, we developed a pre-stress clamp and a device for applying the pre-stress. Contrast tests were conducted between ordinary carbon fiber plates and a pre-stressed carbon fiber plate and between secondary loaded carbon fiber plates and a concrete beam strengthened with a secondary loaded carbon fiber plate. On this basis, we analyzed the failure pattern, the width of cracks and their distribution, the cracking load, the yield load, the limit load and the relation between load and deflec- tion. The results indicate that using pre-stressed carbon fiber plates to strengthen concrete beams is feasible and effective.
文摘Since most current seismic capacity evaluations of reinforced concrete （RC） frame structures are implemented by either static pushover analysis （PA） or dynamic time history analysis, with diverse settings of the plastic hinges （PHs） on such main structural components as columns, beams and walls, the complex behavior of shear failure at beam-column joints （BCJs） during major earthquakes is commonly neglected. This study proposes new nonlinear PA procedures that consider shear failure at BCJs and seek to assess the actual damage to RC structures. Based on the specifications of FEMA-356, a simplified joint model composed of two nonlinear cross struts placed diagonally over the location of the plastic hinge is established, allowing a sophisticated PA to be performed. To verify the validity of this method, the analytical results for the capacity curves and the failure mechanism derived from three different full-size RC frames are compared with the experimental measurements. By considering shear failure at BCJs, the proposed nonlinear analytical procedures can be used to estimate the structural behavior of RC frames, including seismic capacity and the progressive failure sequence of joints, in a precise and effective manner.
文摘In the last two decades, the study of reinforced concrete (RC) structures elements such as bridge deck slabs, bridge girders, or offshore installations, which?are?subjected to cyclic action typically induced by seismic motions has received the attention of many researchers.?Furthermore, the past two decades have witnessed rapid growth in the use of fiber-reinforced polymer (FRP) confining jackets for the strengthening/retrofit of reinforced concrete (RC) columns and beams. Moreover, several theoretical and empirical models?have been proposed for evaluating the?shear strength of beams, columns and beam-to-column joints. In this?paper, an overview of the models currently available in the scientific literature for?evaluating the?shear capacity of?beams, columns and?exterior beam-to-column joints?is reported.?Further, important practical issues which contribute in?shear strengthening of structures with different element types especially RC beams with different strengthening techniques, such as steel plate and FRP laminate are discussed.?Finally,?directions for future research based on the existing gaps of the existing works are presented.
基金by the National Natural Science Foundation of China(No.51878190)。
文摘The influence of carbon fiber reinforced plastic(CFRP)on dynamic mechanical properties of reinforced concrete(RC)beam was studied by drop hammer impact test system.The impact behaviors of beam,including failure mode,impact force peak value and peak deflection were analyzed.The experimental results show that bonding CFRP can reduce the crack width and change the failure mode of the beam.The length of CFRP has a certain influence on the impact force and deflection,and the peak inertia force of most beams is roughly in the range of 1/2-5/6 of the peak impact force.In addition,dynamic increase factor(DIF)increases with the increase of CFRP length,and its maximum value can reach 2.11.
