New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper us...New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper used oneand three-way joint simulation methods to simulate the refrigeration system of new energy vehicles.Firstly,a k-εturbulent flow model for the cooling pump flow field is established based on the principle of computational fluid dynamics.Then,the CFD commercial fluid analysis software FLUENT is used to simulate the flow field of the cooling pump under different inlet flow conditions.This paper proposes an optimization scheme for new energy vehicle engines’“boiling”phenomenon under high temperatures and long-time climbing conditions.The simulation results show that changing the radiator’s structure and adjusting the thermostat’s parameters can solve the problem of a“boiling pot.”The optimized new energy vehicle engine can maintain a better operating temperature range.The algorithm model can reference each cryogenic system component hardware selection and control strategy in the new energy vehicle’s engine.展开更多
Mixing efficiency in two-phase gas–liquid agitated vessel is one of the important challenges in the industrial processes.Computational fluid dynamics technique(CFD)was used to investigate the effect of four different...Mixing efficiency in two-phase gas–liquid agitated vessel is one of the important challenges in the industrial processes.Computational fluid dynamics technique(CFD)was used to investigate the effect of four different pitched blade impellers,including 15°,30°,45°and 60°,on the mixing quality of gas–liquid agitated vessel.The multiphase flow behavior was modeled by Eulerian–Eulerian multiphase approach,and RNG k-εwas used to model the turbulence.The CFD results showed that a strong global vortex plays the main role on the mixing quality of the gas phase in the vessel.Based on the standard deviation criterion,it was observed that the axial distribution of the gas phase in the 30°impeller is about 55%better than the others.In addition,the results showed that the 30°impeller has a uniform radial distribution over the other impellers and the maximum gas phase holdup in the vessel.Investigation of the power consumption of the impellers showed that the 30°impeller has the highest power consumption among the other pitched blade impellers.Also,examine the effect of same power condition for pitched blade impellers showed that the 30°impeller has the best mixing quality in this condition.展开更多
The characteristics of the flow field associated with a multi-hole combined external rotary bit have been studied by means of numerical simulation in the framework of an RNG k-εturbulence model,and compared with the ...The characteristics of the flow field associated with a multi-hole combined external rotary bit have been studied by means of numerical simulation in the framework of an RNG k-εturbulence model,and compared with the results of dedicated rock breaking drilling experiments.The numerical results show that the nozzle velocity and dynamic pressure of the nozzle decrease with an increase in the jet distance,and the axial velocity of the nozzle decays regularly with an increase in the dimensionless jet distance.Moreover,the axial velocity related to the nozzle with inclination angle 20°and 30°can produce a higher hole depth,while the radial velocity of the nozzle with 60°inclination can enlarge the hole diameter.The outcomes of the CFD simulations are consistent with the actual dynamic rock breaking and pore forming process,which lends credence to the present results and indicates that they could be used as a reference for the future optimization of systems based on the multi-hole combined external rotary bit technology.展开更多
In the present study, considering the transport and transformation processes of variables, a threedimensional water quality model for the river system was established, which coupled the volume of fluid(VOF) method wit...In the present study, considering the transport and transformation processes of variables, a threedimensional water quality model for the river system was established, which coupled the volume of fluid(VOF) method with the k-ε turbulence mathematical model. Then, the water hydrodynamic characteristics and transport processes for BOD_5, NH_(3^-)N and TP were analyzed. The results showed that the water surface of convex bank was a little lower than that of concave bank due to the centrifugal force near the bend, and most concentrations were inferior to the type Ⅴ standard indexes of surface water environmental quality. The model validation indicated that the errors between the simulated and monitored values were comparatively small, satisfying the application demands and providing scientific basis and decision support for the restoration and protection of water quality.展开更多
In recent years, thin slab continuous casting technology has been widely used to improve the quality of the product and to reduce the cost. One of the challenges faced by this technology is to design reasonable flow p...In recent years, thin slab continuous casting technology has been widely used to improve the quality of the product and to reduce the cost. One of the challenges faced by this technology is to design reasonable flow patterns, which strongly affect the surface and inner properties of the final slab in the mold. With the fixed scales and complex geometrical structures of nozzle and funnel type mold, a series of numerical simulations are made to analyze the flow patterns in melt steel using finite volume method based on structured body fitted coordinate grids. The CFD （computational fluid dynamics） package is validated first using one typical case described in previously published studies, and then it is developed to study the effect of operational parameters on fluid flow in thin slab caster. Two operational parameters, casting speed and SEN （submerged entry nozzle） depth, are mainly considered for numerical analysis. On the basis of present simulations, the reasonable SEN submergence depths corresponding to different casting speeds are suggested according to fluid flow characteristics like, flow jet impingement on the narrow side of the mold, flow speed of the melt steel beneath the meniscus and the recirculation region. This is the first stage of study on the numerical analysis of the whole thin slab casting process with electromagnetic brake.展开更多
Stepped spillways for significant energy dissipation along the chute have gained interest; popularity among researchers; dam engineers. Due to the complexity of air-water two-phase flow over stepped spillways, the fin...Stepped spillways for significant energy dissipation along the chute have gained interest; popularity among researchers; dam engineers. Due to the complexity of air-water two-phase flow over stepped spillways, the finite volume computational fluid dynamics module of the FLUENT software was used to simulate the main characteristics of the flow. Adopting the RNG k- turbulence model, the mixture flow model for air-water two-phase flow was used to simulate the flow field over stepped spillway with the PISO arithmetic technique. The numerical result successfully reproduced the complex flow over a stepped spillway of an experiment case, including the interaction between entrained air bubbles; cavity recirculation in the skimming flow regime, velocity distribution; the pressure profiles on the step surface as well. The result is helpful for understanding the detailed information about energy dissipation over stepped spillways.展开更多
Air entrainment is known to be one of efficient and inexpensive methods to prevent cavitation damages in hydropower projects.The shape of sudden expansion-fall is used as a common device for mitigating cavitation eros...Air entrainment is known to be one of efficient and inexpensive methods to prevent cavitation damages in hydropower projects.The shape of sudden expansion-fall is used as a common device for mitigating cavitation erosions.The complex flow patterns with cavitation are numerically simulated by using the realizable k-εturbulence model and the air-water mixture model.The calculated results are compared well with the experimental results as well as those obtained with the k-εturbulence model with the Volume Of Fluid（VOF）Model.The calculated results agree well with the experimental data for the aeration cavity and wall pressure.Moreover,the air concentration near sidewall is simulated by a mixture model.It is found that the mixture turbulence model is superior to the VOF turbulence model.展开更多
As it is almost impossible to carry out the prototype hydro-turbine experiment be- fore the power plant is built up, rational prediction of pressure fluctuations in the prototype turbine is very important at the desig...As it is almost impossible to carry out the prototype hydro-turbine experiment be- fore the power plant is built up, rational prediction of pressure fluctuations in the prototype turbine is very important at the design stage. From this viewpoint, we at first treated the unsteady turbulent flow computation based on the modified RNG k-ε turbulence model through the whole flow passage to simulate the pressure fluctuation in a model turbine. Since fair agreement was recognized between the numerical results and the experimental data, this numerical method was applied to simulate the pressure fluctuations in the prototype turbine. From the comparison of them with the model turbine results, it is seen that their qualitative trend of pres- sure fluctuations are similar, but an appreciable difference is observed between the amplitudes of pressure fluctuation of the prototype turbine and that of the model turbine. Though the present findings may be explained by the effect of Reynolds number, further studies are expected for quantitative interpretation. We paid atten- tion to the interaction between the fluid and turbine structure. Adopting a weak fluid-solid coupling method, we studied the pressure fluctuation in the prototype turbine to clarify how the elastic behavior of runner blades influenced the charac- teristics of pressure fluctuation.展开更多
The 3-D turbulent flows in a valve pipe were described by the incompressibleReynolds-averaged Navier-Stokes equations with an RNG k-ε turbulence model. With the finite volumemethod and a body-fitted coordinate system...The 3-D turbulent flows in a valve pipe were described by the incompressibleReynolds-averaged Navier-Stokes equations with an RNG k-ε turbulence model. With the finite volumemethod and a body-fitted coordinate system, the discretised equations were solved by the SIMPLESTalgorithm. The numerical result of a cut-off valve with curved inlet shows the flow characteristicsand the main cause of energy loss when fluid flows through a valve. And then, the boundaries ofvalve were modified in order to reduce the energy loss. The computational results of modified valveshow that the numerical value of turbulent kinetic energy is lower, and that the modified design ofthe 3-D valve boundaries is much better. The analysis of the result also shows that RNG k-εturbulence model can successfully be used to predict the 3-D turbulent separated flows and thesecondary flow inside valve pipes.展开更多
A 2-D depth averaged RNG k- ε model is developed to simulate the flow in a typical reach of the Upper Yellow River with non-monotonic banks. In order to take account of the effect of the secondary flow in a bend, the...A 2-D depth averaged RNG k- ε model is developed to simulate the flow in a typical reach of the Upper Yellow River with non-monotonic banks. In order to take account of the effect of the secondary flow in a bend, the momentum equations are modified by adding an additional source term. A comparison between the numerical simulation and the field measurements indicates that the improved 2-D depth averaged RNG k- ε model can improve the accuracy of the numerical simulation. An arc spline interpolation method is developed to interpolate the non-monotonic river banks. The method can also be reasonably applied for the 2-D interpolation of the river bed level. Through a comparison of the water surface gradients simulated in the seven bends of the studied reach, some analytical formulae are improved to reasonably calculate the longitudinal and transverse gradients in meandering river reaches. Furthermore, the positions of the maximum water depth and the maximum velocity in a typical bend are discussed.展开更多
文摘New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper used oneand three-way joint simulation methods to simulate the refrigeration system of new energy vehicles.Firstly,a k-εturbulent flow model for the cooling pump flow field is established based on the principle of computational fluid dynamics.Then,the CFD commercial fluid analysis software FLUENT is used to simulate the flow field of the cooling pump under different inlet flow conditions.This paper proposes an optimization scheme for new energy vehicle engines’“boiling”phenomenon under high temperatures and long-time climbing conditions.The simulation results show that changing the radiator’s structure and adjusting the thermostat’s parameters can solve the problem of a“boiling pot.”The optimized new energy vehicle engine can maintain a better operating temperature range.The algorithm model can reference each cryogenic system component hardware selection and control strategy in the new energy vehicle’s engine.
基金Semnan University for the financial support of this research(grant number 845)。
文摘Mixing efficiency in two-phase gas–liquid agitated vessel is one of the important challenges in the industrial processes.Computational fluid dynamics technique(CFD)was used to investigate the effect of four different pitched blade impellers,including 15°,30°,45°and 60°,on the mixing quality of gas–liquid agitated vessel.The multiphase flow behavior was modeled by Eulerian–Eulerian multiphase approach,and RNG k-εwas used to model the turbulence.The CFD results showed that a strong global vortex plays the main role on the mixing quality of the gas phase in the vessel.Based on the standard deviation criterion,it was observed that the axial distribution of the gas phase in the 30°impeller is about 55%better than the others.In addition,the results showed that the 30°impeller has a uniform radial distribution over the other impellers and the maximum gas phase holdup in the vessel.Investigation of the power consumption of the impellers showed that the 30°impeller has the highest power consumption among the other pitched blade impellers.Also,examine the effect of same power condition for pitched blade impellers showed that the 30°impeller has the best mixing quality in this condition.
基金the Science and Technology Innovation and Entrepreneurship Fund of China Coal Technology Engineering Group(2019-TD-QN038,2019-TDQN017)Enterprise Independent Innovation Guidance Project(2018ZDXM05,2019YBXM30).
文摘The characteristics of the flow field associated with a multi-hole combined external rotary bit have been studied by means of numerical simulation in the framework of an RNG k-εturbulence model,and compared with the results of dedicated rock breaking drilling experiments.The numerical results show that the nozzle velocity and dynamic pressure of the nozzle decrease with an increase in the jet distance,and the axial velocity of the nozzle decays regularly with an increase in the dimensionless jet distance.Moreover,the axial velocity related to the nozzle with inclination angle 20°and 30°can produce a higher hole depth,while the radial velocity of the nozzle with 60°inclination can enlarge the hole diameter.The outcomes of the CFD simulations are consistent with the actual dynamic rock breaking and pore forming process,which lends credence to the present results and indicates that they could be used as a reference for the future optimization of systems based on the multi-hole combined external rotary bit technology.
基金Supported by the Innovative Research Groups of National Natural Science Foundation of China(No.51321065)the Major Science and Technology Program for Water Pollution Control and Treatment(2012ZX07101-008)the National Natural Science Foundation of China(No.51439005)
文摘In the present study, considering the transport and transformation processes of variables, a threedimensional water quality model for the river system was established, which coupled the volume of fluid(VOF) method with the k-ε turbulence mathematical model. Then, the water hydrodynamic characteristics and transport processes for BOD_5, NH_(3^-)N and TP were analyzed. The results showed that the water surface of convex bank was a little lower than that of concave bank due to the centrifugal force near the bend, and most concentrations were inferior to the type Ⅴ standard indexes of surface water environmental quality. The model validation indicated that the errors between the simulated and monitored values were comparatively small, satisfying the application demands and providing scientific basis and decision support for the restoration and protection of water quality.
文摘In recent years, thin slab continuous casting technology has been widely used to improve the quality of the product and to reduce the cost. One of the challenges faced by this technology is to design reasonable flow patterns, which strongly affect the surface and inner properties of the final slab in the mold. With the fixed scales and complex geometrical structures of nozzle and funnel type mold, a series of numerical simulations are made to analyze the flow patterns in melt steel using finite volume method based on structured body fitted coordinate grids. The CFD （computational fluid dynamics） package is validated first using one typical case described in previously published studies, and then it is developed to study the effect of operational parameters on fluid flow in thin slab caster. Two operational parameters, casting speed and SEN （submerged entry nozzle） depth, are mainly considered for numerical analysis. On the basis of present simulations, the reasonable SEN submergence depths corresponding to different casting speeds are suggested according to fluid flow characteristics like, flow jet impingement on the narrow side of the mold, flow speed of the melt steel beneath the meniscus and the recirculation region. This is the first stage of study on the numerical analysis of the whole thin slab casting process with electromagnetic brake.
基金supported by the National Natural Science Foundation of China(Grant No.50609011).
文摘Stepped spillways for significant energy dissipation along the chute have gained interest; popularity among researchers; dam engineers. Due to the complexity of air-water two-phase flow over stepped spillways, the finite volume computational fluid dynamics module of the FLUENT software was used to simulate the main characteristics of the flow. Adopting the RNG k- turbulence model, the mixture flow model for air-water two-phase flow was used to simulate the flow field over stepped spillway with the PISO arithmetic technique. The numerical result successfully reproduced the complex flow over a stepped spillway of an experiment case, including the interaction between entrained air bubbles; cavity recirculation in the skimming flow regime, velocity distribution; the pressure profiles on the step surface as well. The result is helpful for understanding the detailed information about energy dissipation over stepped spillways.
基金Project supported by the Key Science Foundation of Ministry of Education of China (Grant No. 2008108111)the National Basic Research Program of China (973 Program, Grant No. 2007CB714105)the Program of New Century Excellent Talents in University (Grant No. NCET-08-0378)
文摘Air entrainment is known to be one of efficient and inexpensive methods to prevent cavitation damages in hydropower projects.The shape of sudden expansion-fall is used as a common device for mitigating cavitation erosions.The complex flow patterns with cavitation are numerically simulated by using the realizable k-εturbulence model and the air-water mixture model.The calculated results are compared well with the experimental results as well as those obtained with the k-εturbulence model with the Volume Of Fluid（VOF）Model.The calculated results agree well with the experimental data for the aeration cavity and wall pressure.Moreover,the air concentration near sidewall is simulated by a mixture model.It is found that the mixture turbulence model is superior to the VOF turbulence model.
基金Supported by the National Natural Science Foundation of China(Grant No.90410019)
文摘As it is almost impossible to carry out the prototype hydro-turbine experiment be- fore the power plant is built up, rational prediction of pressure fluctuations in the prototype turbine is very important at the design stage. From this viewpoint, we at first treated the unsteady turbulent flow computation based on the modified RNG k-ε turbulence model through the whole flow passage to simulate the pressure fluctuation in a model turbine. Since fair agreement was recognized between the numerical results and the experimental data, this numerical method was applied to simulate the pressure fluctuations in the prototype turbine. From the comparison of them with the model turbine results, it is seen that their qualitative trend of pres- sure fluctuations are similar, but an appreciable difference is observed between the amplitudes of pressure fluctuation of the prototype turbine and that of the model turbine. Though the present findings may be explained by the effect of Reynolds number, further studies are expected for quantitative interpretation. We paid atten- tion to the interaction between the fluid and turbine structure. Adopting a weak fluid-solid coupling method, we studied the pressure fluctuation in the prototype turbine to clarify how the elastic behavior of runner blades influenced the charac- teristics of pressure fluctuation.
文摘The 3-D turbulent flows in a valve pipe were described by the incompressibleReynolds-averaged Navier-Stokes equations with an RNG k-ε turbulence model. With the finite volumemethod and a body-fitted coordinate system, the discretised equations were solved by the SIMPLESTalgorithm. The numerical result of a cut-off valve with curved inlet shows the flow characteristicsand the main cause of energy loss when fluid flows through a valve. And then, the boundaries ofvalve were modified in order to reduce the energy loss. The computational results of modified valveshow that the numerical value of turbulent kinetic energy is lower, and that the modified design ofthe 3-D valve boundaries is much better. The analysis of the result also shows that RNG k-εturbulence model can successfully be used to predict the 3-D turbulent separated flows and thesecondary flow inside valve pipes.
基金supported by the National Natural Science Foun-dation of China(Grant Nos.91230111,11361002)the Natural Science Foundation of Ningxia Hui Autonomous Region(Grant No.NZ13086)
文摘A 2-D depth averaged RNG k- ε model is developed to simulate the flow in a typical reach of the Upper Yellow River with non-monotonic banks. In order to take account of the effect of the secondary flow in a bend, the momentum equations are modified by adding an additional source term. A comparison between the numerical simulation and the field measurements indicates that the improved 2-D depth averaged RNG k- ε model can improve the accuracy of the numerical simulation. An arc spline interpolation method is developed to interpolate the non-monotonic river banks. The method can also be reasonably applied for the 2-D interpolation of the river bed level. Through a comparison of the water surface gradients simulated in the seven bends of the studied reach, some analytical formulae are improved to reasonably calculate the longitudinal and transverse gradients in meandering river reaches. Furthermore, the positions of the maximum water depth and the maximum velocity in a typical bend are discussed.
