Power transfer efficiency in an air-breathing radio frequency ion thruster

Due to a series of challenges such as low-orbit maintenance of satellites, the air-breathing electric propulsion has got widespread attention. Commonly, the radio frequency ion thruster is favored by low-orbit missions due to its high specific impulse and efficiency. In this paper, the power transfer efficiency of the radio frequency ion thruster with different gas compositions is studied experimentally, which is obtained by measuring the radio frequency power and current of the antenna coil with and without discharge operation. The results show that increasing the turns of antenna coils can effectively improve the radio frequency power transfer efficiency, which is due to the improvement of Q factor. In pure N_2 discharge,with the increase of radio frequency power, the radio frequency power transfer efficiency first rises rapidly and then exhibits a less steep increasing trend. The radio frequency power transfer efficiency increases with the increase of gas pressure at relatively high power, while declines rapidly at relatively low power. In N_(2)/O_(2) discharge, increasing the N_(2) content at high power can improve the radio frequency power transfer efficiency, but the opposite was observed at low power. In order to give a better understanding of these trends, an analytic solution in limit cases is utilized, and a Langmuir probe was employed to measure the electron density. It is found that the evolution of radio frequency power transfer efficiency can be well explained by the variation of plasma resistance, which is related to the electron density and the effective electron collision frequency.

Experimental results of a magnetic field modification to the radio frequency driver of a negative ion source

A magnetic field produced by a current flowing through the plasma grid(PG) is one of the solutions to reduce the collisional loss of negative ions in a negative ion source, which reduces the electron temperature in front of the PG. However, the magnetic field diffused into the driver has some influence on the plasma outflowing. In order to investigate the effect of changing this magnetic field on the outflowing of plasma from the driver, a circular ring(absorber) of high permeability iron has been introduced at the driver exit, which can reduce the magnetic field around it and improve plasma outflowing. With the application of the absorber, the electron density is increased by about 35%, and the extraction current measured from the extraction grid is increased from 1.02 A to 1.29 A. The results of the extraction experiment with cesium injection show that both the extraction grid(EG) current and H-current are increased when the absorber is introduced.

Hollow cathode effect in radio frequency hollow electrode discharge in argon

Radio frequency capacitively coupled plasma source(RF-CCP)with a hollow electrode can increase the electron density through the hollow cathode effect(HCE),which offers a method to modify the spatial profiles of the plasma density.In this work,the variations of the HCE in one RF period are investigated by using a two-dimensional particle-in-cell/Monte-Carlo collision(PIC/MCC)model.The results show that the sheath electric field,the sheath potential drop,the sheath thickness,the radial plasma bulk width,the electron energy distribution function(EEDF),and the average electron energy in the cavity vary in one RF period.During the hollow electrode sheath's expansion phase,the secondary electron heating and sheath oscillation heating in the cavity are gradually enhanced,and the frequency of the electron pendular motion in the cavity gradually increases,hence the HCE is gradually enhanced.However,during the hollow electrode sheath's collapse phase,the secondary electron heating is gradually attenuated.In addition,when interacting with the gradually collapsed hollow electrode sheaths,high-energy plasma bulk electrons in the cavity will lose some energy.Furthermore,the frequency of the electron pendular motion in the cavity gradually decreases.Therefore,during the hollow electrode sheath's collapse phase,the HCE is gradually attenuated.

Radio Frequency Fingerprinting Identification Using Semi-Supervised Learning with Meta Labels

Radio frequency fingerprinting(RFF)is a remarkable lightweight authentication scheme to support rapid and scalable identification in the internet of things(IoT)systems.Deep learning(DL)is a critical enabler of RFF identification by leveraging the hardware-level features.However,traditional supervised learning methods require huge labeled training samples.Therefore,how to establish a highperformance supervised learning model with few labels under practical application is still challenging.To address this issue,we in this paper propose a novel RFF semi-supervised learning(RFFSSL)model which can obtain a better performance with few meta labels.Specifically,the proposed RFFSSL model is constituted by a teacher-student network,in which the student network learns from the pseudo label predicted by the teacher.Then,the output of the student model will be exploited to improve the performance of teacher among the labeled data.Furthermore,a comprehensive evaluation on the accuracy is conducted.We derive about 50 GB real long-term evolution(LTE)mobile phone’s raw signal datasets,which is used to evaluate various models.Experimental results demonstrate that the proposed RFFSSL scheme can achieve up to 97%experimental testing accuracy over a noisy environment only with 10%labeled samples when training samples equal to 2700.

Comparison of pulse-modulated and continuous operation modes of a radio-frequency inductive ion source

The paper describes an experimental study of the characteristics of a pulse-modulated radiofrequency(RF)discharge sustained at low pressures,typical of the operating modes of RF gridded ion sources.The motivation for the study is the question of whether the RF pulsemodulated mode can increase the efficiency of the ion source.The ion current values extracted from an RF inductive ion source operating in continuous and pulse-modulated modes were compared.The experimental data were also compared with the parameter calculations based on a0D numerical model of the discharge.The measurements showed that the pulse-modulated operation mode of the RF ion source had a noticeable advantage when the power of the RF generator was 140 W or lower.However,as the generator power increased,the advantage was lost because the pulse-modulated operation mode,having a higher RF power instant value,entered the region of existence sooner than the continuous mode,where the ion production cost begins to grow with RF power.

Ignition dynamics of radio frequency discharge in atmospheric pressure cascade glow discharge

A cascade glow discharge in atmospheric helium was excited by a microsecond voltage pulse and a pulse-modulated radio frequency(RF) voltage, in which the discharge ignition dynamics of the RF discharge burst was investigated experimentally. The spatio-temporal evolution of the discharge, the ignition time and optical emission intensities of plasma species of the RF discharge burst were investigated under different time intervals between the pulsed voltage and RF voltage in the experiment. The results show that by increasing the time interval between the pulsed discharge and RF discharge burst from 5 μs to 20 μs, the ignition time of the RF discharge burst is increased from 1.6 μs to 2.0 μs, and the discharge spatial profile of RF discharge in the ignition phase changes from a double-hump shape to a bell-shape. The light emission intensity at 706 nm and 777 nm at different time intervals indicates that the RF discharge burst ignition of the depends on the number of residual plasma species generated in the pulsed discharges.

Radio Frequency Fingerprint-Based Satellite TT&C Ground Station Identification Method

This study presents a radio frequency(RF)fingerprint identification method combining a convolutional neural network(CNN)and gated recurrent unit(GRU)network to identify measurement and control signals.The proposed algorithm(CNN-GRU)uses a convolutional layer to extract the IQ-related learning timing features.A GRU network extracts timing features at a deeper level before outputting the final identification results.The number of parameters and the algorithm’s complexity are reduced by optimizing the convolutional layer structure and replacing multiple fully-connected layers with gated cyclic units.Simulation experiments show that the algorithm achieves an average identification accuracy of 84.74% at a -10 dB to 20 dB signal-to-noise ratio(SNR)with fewer parameters and less computation than a network model with the same identification rate in a software radio dataset containing multiple USRP X310s from the same manufacturer,with fewer parameters and less computation than a network model with the same identification rate.The algorithm is used to identify measurement and control signals and ensure the security of the measurement and control link with theoretical and engineering applications.

Three-dimensional numerical simulation of heating and melting behaviors of cerium oxide powders in radio frequency thermal plasma

The present study aims at the numerical simulations of the melting process of cerium oxide particles in RF thermal plasma.The physical model and the calculating method were described firstly;the interaction between cerium oxide particles and plasma was analyzed;specific attention was given to the effects of particle initial size,injection velocity on the particle melting and trajectory in plasma.The influence of the temperature field and velocity field distribution of the plasma around the particle trajectory on the melting effect is analyzed,and the relationship between the heat absorption efficiency of the particles and the particle size reduction process is further determined.It is also found that there exists an optimal particle initial injection velocity which led to a more concentrated final particle size distribution and a more significant reduction of particle size.The results could provide effective guidance for understanding the plasma spheroidization process of uranium dioxide and cerium dioxide powder particles.

Impact of endoscopic ultrasound-guided radiofrequency ablation in managing pancreatic malignancy

Pancreatic malignancy is still the most lethal gastrointestinal malignancy.It has a very poor prognosis with low survival rate.Surgery is still the main treatment option for pancreatic malignancy.Most patients already have locally advanced and even late stage disease due to non-specific abdominal symptoms.Even though some cases are still suitable for surgical treatment,due to its aggressiveness adjuvant chemotherapy is becoming the standard treatment for controlling the disease.Radiofrequency ablation(RFA)is a thermal therapy that has been used as one of the standard treatments for liver malignancy.It can also be performed intraoperatively.There are several reports on percutaneous RFA treatment for pancreatic malignancy using transabdominal ultrasound and guided by computed tomography scan.However,due to its anatomical location and the risk of high radiation exposure,these methods seem to be very limited.Endoscopic ultrasound(EUS)has been widely used for pancreatic abnormality evaluation due to its ability to detect more accurately,especially small pancreatic lesions,compared to other imaging modalities.By the EUS approach,it is easier to achieve good visualization of tumor ablation and necrosis as the echoendoscope position is closer to the tumor area.Based on studies and a recent meta-analysis,EUS-guided RFA is a promising treatment approach for most pancreatic malignancy cases,but most studies only collected data from a small sample size.Larger studies are needed before clinical recommendations can be made.

Radio Frequency Gluing Technique for Wood-to-Wood Bonding: Review

White glues, also referred to as polyvinyl acetate (PVAc) adhesives, are thermoplastics that soften when heated to a specific degree and re-harden when cooled. For general assembly tasks in the joinery business, such as edge gluing, wood veneer, and edge bonding, white glues have been used. White glue requires a prolonged setting time to achieve adequate handling strength as it solidifies through evaporation or absorption of water by the wood. Cold press and hot press techniques are used to bond wood substrates. Recently, white glue is frequently used as a wood adhesive with dielectric heating systems to prevent this and enhance production speeds. Radio frequency (RF) curing is merely a technique for heating glue lines in wood-to-wood joints. It considered a source of heat, like steam and electricity. In order to bond wood substrates with the least amount of clamping time, the RF produces a very rapid, uniform rise in temperature. In this review paper, we discussed the radio frequency curing technique, their mechanism and troubleshooting to achieve perfect wood bond in joinery segment.

Air target recognition method against ISRJ for radio frequency proximity sensors using chaotic stream encryption

The interrupted-sampling repeater jamming(ISRJ)can cause false targets to the radio-frequency proximity sensors(RFPSs),resulting in a serious decline in the target detection capability of the RFPS.This article proposes a recognition method for RFPSs to identify the false targets caused by ISRJ.The proposed method is realized by assigning a unique identity(ID)to each RFPS,and each ID is a periodically and chaotically encrypted in every pulse period.The processing technique of the received signal is divided into ranging and ID decryption.In the ranging part,a high-resolution range profile(HRRP)can be obtained by performing pulse compression with the binary chaotic sequences.To suppress the noise,the singular value decomposition(SVD)is applied in the preprocessing.Regarding ID decryption,targets and ISRJ can be recognized through the encryption and decryption processes,which are controlled by random keys.An adaptability analysis conducted in terms of the peak-to-side lobe ratio(PSLR)and bit error rate(BER)indicates that the proposed method performs well within a 70-k Hz Doppler shift.A simulation and experimental results show that the proposed method achieves extremely stable target and ISRJ recognition accuracies at different signal-to-noise ratios(SNRs)and jamming-to-signal ratios(JSRs).

Performance of a 4 cm iodine-fueled radio frequency ion thruster

The performance of an iodine radio ion thruster with a 4 cm diameter(IRIT4)was studied experimentally in this paper.Regulation of the mass flow rates of the iodine propellant is achieved by using a temperature control method of the iodine reservoir.Performance of the thruster using iodine as propellants is obtained at different total thruster powers of 40.6–128.8 W,different grid voltages of 1000–1800 V and the iodine flow rate of 100μgs^(-1).Results show that thrust and specific impulse increase approximately linearly with the increasing total thruster power and the screen grid voltage.The thrust of 2.32 mN and the specific impulse of 2361 s are obtained at the nominal total thruster power of 95.8 W and the screen grid voltage of 1800 V.It is also indicated that performance of the iodine propellant is comparable to that of the xenon propellant;and a difference between them is that the iodine thrust is slightly higher than xenon when the total thruster power is more than 62 W.At the nominal 95.8 W total thruster power,the thrust values of them are 2.32 m N and 2.15 mN respectively,and the thrust-to-power ratios of them are 24.2 mN kW^(-1)and 23.5 mN kW^(-1),respectively.

Application of Radio Frequency Identification (RFID) in Dairy Information Management

As a kind of brand-new technology, radio frequency identification management, data control and acquisition. This paper introduced food safety system construction, analyzed the advantages and problems in dairy modem suggestions for solution according to the practical situation. （RFID） plays an important role in dairy information tracing and culture function extension of managing breeding technology, and finally put forward some

Influence of anode temperature on ignition performance of the IRIT4-2D iodine-fueled radio frequency ion thruster

This paper reports the ignition performance of the iodine-fueled radio frequency(RF)ion thruster(IRIT)at different anode temperaturesT_(a0).The experimental results show that the anode temperature plays important role on the ignition process of the IRIT.There were two characteristic temperatures related to the anode:the minimum ignition temperatureT_(i0)and the stable ignition temperatureT_(is),which were much lower than the pipeline temperature and the storage tank temperature.AtT_(a0)<T_(i0),it failed to discharge.WhenT_(i0)≤T_(a0)<T_(is),it was ignited with dramatical oscillations.AtT_(a0)≥T_(is),the discharge was stable in a large anode temperature range.The analysis showed that the different discharge phenomena at different anode temperatures were attributed to the change of iodine flow rate during the process of the iodine deposition-clogging and sublimation-clearing inside the thruster.The research helps improve the preheating design of the iodine-fueled electric thruster.

Electrical and thermal characterization of near-surface electrical discharge plasma actuation driven by radio frequency voltage at low pressure

The electrical and thermal characterization of near-surface electrical discharge plasma driven by radio frequency voltage are investigated experimentally in this paper. The influences of operating pressure, electrode distance, and duty cycle on the discharge are studied. When pressure reaches 60 Ton. （1 Torr= 1.33322 x 102 Pa） the transition from diffuse glow mode to constricted mode occurs. With the operating pressure varying from 10 Tort to 60 Torr, the discharge energy calculated from the charge-voltage （Q-V） Lissajous figure decreases rapidly, while it remains unchanged between 60 Torr and 460 Torr. Under certain experimental conditions, there exists an optimized electrode distance （8 mm）. As the duty cycle of applied voltage increases, the voltage-current waveforms and Q-V Lissajous figures show no distinct changes.

Thermal and induced flow characteristics of radio frequency surface dielectric barrier discharge plasma actuation at atmospheric pressure

Thermal and induced flow velocity characteristics of radio frequency（RF） surface dielectric barrier discharge（SDBD）plasma actuation are experimentally investigated in this paper. The spatial and temporal distributions of the dielectric surface temperature are measured with the infrared thermography at atmospheric pressure. In the spanwise direction, the highest dielectric surface temperature is acquired at the center of the high voltage electrode, while it reduces gradually along the chordwise direction. The maximum temperature of the dielectric surface raises rapidly once discharge begins.After several seconds（typically 100 s）, the temperature reaches equilibrium among the actuator＇s surface, plasma, and surrounding air. The maximum dielectric surface temperature is higher than that powered by an AC power supply in dozens of k Hz. Influences of the duty cycle and the input frequency on the thermal characteristics are analyzed. When the duty cycle increases, the maximum dielectric surface temperature increases linearly. However, the maximum dielectric surface temperature increases nonlinearly when the input frequency varies from 0.47 MHz to 1.61 MHz. The induced flow velocity of the RF SDBD actuator is 0.25 m/s.

Fabrication and properties of high performance YBa_2Cu_3O_(7-δ) radio frequency SQUIDs with step-edge Josephson junctions

We describe the fabrication of high performance YBa2Cu3O7-δ （YBCO） radio frequency （RF） superconducting quantum interference devices （SQUIDs）, which were prepared on 5 mm×5 mm LaAlO3 （LAO） substrates by employing stepedge junctions （SEJs） and in flip-chip configuration with 12 mm×12 mm resonators. The step in the substrate was produced by Ar ion etching with step angles ranging from 47° to 61°, which is steep enough to ensure the formation of grain boundaries （GBs） at the step edges. The YBCO film was deposited using the pulsed laser deposition （PLD） technique with a film thickness half of the height of the substrate step. The inductance of the SQUID washer was designed to be about 157 pH. Under these circumstances, high performance YBCO RF SQUIDs were successfully fabricated with a typical flux-voltage transfer ratio of 83 mV/φ0, a white flux noise of 29 μφ0/√Hz, and the magnetic field sensitivity as high as 80 fT/√Hz. These devices have been applied in magnetocardiography and geological surveys.

Surface modification of silicone rubber by CF4 radio frequency capacitively coupled plasma for improvement of flashover

The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled plasma(CCP)for the improvement of surface insulation performance.The discharge mode and active particles of CCP are diagnosed by the digital single-lens reflex and the spectrometer.Scanning electron microscopy and x-ray photoelectron spectroscopy are used for the surface physicochemical properties of samples,while the surface charge dissipation,charge accumulation measurement,and flashover test are applied for the surface electrical characteristics.Experimental results show that the fluorocarbon groups can be grafted and the surface roughness increases after plasma treatment.Besides,the surface charge dissipation is decelerated and the positive charge accumulation is inhibited obviously for the treated samples.Furthermore,the surface flashover voltage can be increased by 26.67%after 10 min of treatment.It is considered that strong electron affinity of C–F and increased surface roughness can contribute to deepening surface traps,which not only inhibits the development of secondary electron emission avalanche but also alleviates the surface charge accumulation and finally improves the surface flashover voltage of SIR.

Effective Treatment of Atrophic and Icepick Acne Scars Using Deep Non-Ablative Radiofrequency and Multisource Fractional RF Skin Resurfacing

Background and Objectives: Effective treatment for atrophic (depressed) and icepick acne scars requires treatment of both epidermis—for roughness, texture and hyperpigmentation, and the dermis—for collagen remodeling. All first generation radiofrequency systems allow nonablative RF treatment while a few others allow simple bipolar Fractional RF skin resurfacing. The FDA cleared multisource radiofrequency therapy system (EndyMed PRO, EndyMed Ltd., Cesarea, Israel) allows, for the first time, phase controlled multisource RF for both deep (up to 11 mm) non ablative RF and fractional RF skin resurfacing on the same treatment device. Study Design/Materials and Methods: Ten subjects with atrophic acne scars were enrolled in the study. Patients were photographed using standardized methods. In each treatment session, each patient received a full face 3DEEP non ablative skin tightening treatment followed by a Fractional skin resurfacing treatment. The treatment sessions were repeated once a month to a total of up to 4 treatments. Results: All subjects experienced mild-moderate edema and erythema as an immediate response to treatment. Edema resolved after up to three hours post treatment and erythema lasted up to 2 days. Micro ablative crusts were formed 1 - 2 days post treatments and lasted up to 5 days on facial areas. Patients' photographs—before each treatment session and 1 and 3 months after the last session—were graded according to the accepted Cosmetic Improvement Scale. All patients obtained significant skin improvement. Seventy percent of patients had 50% - 75% improvement one month after the third treatment session while the other thirty percent experienced a 25% - 50%. Discussion and Conclusions: The presented results describe for the first time a new treatment system (EndyMed PROTM) that allows both deep non ablative RF delivery and Fractional skin resurfacing on the same treatment platform. This work shows the synergy of combining these two applications for the improvement of acne scars, as well as for some secondary possible pigmentation and vascular improvement.