Verification of operation parameters of VVER-1200 NPP Simulator installed at Nuclear Training Center, VINATOM has been performed. This simulator has been supplied for Vietnam in the framework of IAEA TC Project VIE201...Verification of operation parameters of VVER-1200 NPP Simulator installed at Nuclear Training Center, VINATOM has been performed. This simulator has been supplied for Vietnam in the framework of IAEA TC Project VIE2010 on Developing Nuclear Power Infrastructure—Phase II hosted by the Vietnam Atomic Energy Agency (VAEA). The comparison of the main parameters in nominal power operation with design data given in safety analysis report of VVER-1200/V392M as well as Ninh Thuan FSSAR is presented. In this study, the reactor coolant coast-down transient is investigated using the VVER-1200 NPP simulator. The simulated results performed in the simulator through switching off one reactor coolant pump in comparisons with experiment results performed in VVER-1000 reactor are given. The similarity between the measured and simulated results shows that the thermal hydraulic characteristics and the control protection systems are modeled in a reasonable way. A good agreement in operating parameters was found between the VVER-1200 NPP simulator and VVER-1200/V392M’s PSAR.展开更多
This paper introduces the simulation, and controls using Simulink of MATLAB for PCTRAN (Personal Computer Transient Analysis) of the power control system (PWR) type pressurized water reactor of PWR WESTINGHOUSE AP1000...This paper introduces the simulation, and controls using Simulink of MATLAB for PCTRAN (Personal Computer Transient Analysis) of the power control system (PWR) type pressurized water reactor of PWR WESTINGHOUSE AP1000. The power controller model produces mathematical model description in nonlinear relation form in Simulink of MATLAB which is an important and popular program used at most universities for education. The power controller is described by a block diagram in this paper and some details introduce to clearly understand the work function. The results of action control compared with the PCTRAN programme in modes of automatic and manual control.展开更多
A code. OPTROD. based on dynamic programming method is developed and utilized to optimize control rod positions throughout the fuel cycle of the 200 MW nuclear heating reactor (NHR-200). A fuel cycle is divided into m...A code. OPTROD. based on dynamic programming method is developed and utilized to optimize control rod positions throughout the fuel cycle of the 200 MW nuclear heating reactor (NHR-200). A fuel cycle is divided into many steps or stages. Optimization of the multistage process is solved iteratively in the forward direction throughout a fuel cycle. The dynamic programming method is much more efficient than the normal nonlinear programming method. Convergence is obtained even if poor initial control rod positions are given.展开更多
功率控制系统(Power Control System,PCS)是反应堆控制系统(Reactor Control System,RCS)的重要组成部分,它完成功率提升、功率保持与功率调节的作用。在钍基熔盐堆(Thorium Molten Salt Reactor,TMSR)核能系统固态堆设计方案中,功率控...功率控制系统(Power Control System,PCS)是反应堆控制系统(Reactor Control System,RCS)的重要组成部分,它完成功率提升、功率保持与功率调节的作用。在钍基熔盐堆(Thorium Molten Salt Reactor,TMSR)核能系统固态堆设计方案中,功率控制器根据实测功率与设定功率值之间的偏差和偏差的变化趋势,按照经典的比例-积分-微分(Proportional Integral Derivative,PID)控制算法,给出调节控制棒的运动距离和运动方向等信号。PCS的PID算法设计与基于反应堆中子物理、热工及控制棒的传动性能构成的闭环控制系统的特性有关,其不同参数的确定与系统的静态和动态性能指标的要求相对应。本文从控制的角度出发,在已有的控制棒样机中设计的棒控棒位系统及相关中子物理的基础上对PCS的PID算法进行多层次仿真与参数分析,并对系统的可控性与可测性进行分析验证。分析及仿真结果表明两种控制模型下的系统均是完全可控及完全可测的,在合适的PID参数集下均能体现响应的快速性及系统的良好鲁棒性和抗干扰能力,具有实际的应用意义。展开更多
文摘Verification of operation parameters of VVER-1200 NPP Simulator installed at Nuclear Training Center, VINATOM has been performed. This simulator has been supplied for Vietnam in the framework of IAEA TC Project VIE2010 on Developing Nuclear Power Infrastructure—Phase II hosted by the Vietnam Atomic Energy Agency (VAEA). The comparison of the main parameters in nominal power operation with design data given in safety analysis report of VVER-1200/V392M as well as Ninh Thuan FSSAR is presented. In this study, the reactor coolant coast-down transient is investigated using the VVER-1200 NPP simulator. The simulated results performed in the simulator through switching off one reactor coolant pump in comparisons with experiment results performed in VVER-1000 reactor are given. The similarity between the measured and simulated results shows that the thermal hydraulic characteristics and the control protection systems are modeled in a reasonable way. A good agreement in operating parameters was found between the VVER-1200 NPP simulator and VVER-1200/V392M’s PSAR.
文摘This paper introduces the simulation, and controls using Simulink of MATLAB for PCTRAN (Personal Computer Transient Analysis) of the power control system (PWR) type pressurized water reactor of PWR WESTINGHOUSE AP1000. The power controller model produces mathematical model description in nonlinear relation form in Simulink of MATLAB which is an important and popular program used at most universities for education. The power controller is described by a block diagram in this paper and some details introduce to clearly understand the work function. The results of action control compared with the PCTRAN programme in modes of automatic and manual control.
文摘A code. OPTROD. based on dynamic programming method is developed and utilized to optimize control rod positions throughout the fuel cycle of the 200 MW nuclear heating reactor (NHR-200). A fuel cycle is divided into many steps or stages. Optimization of the multistage process is solved iteratively in the forward direction throughout a fuel cycle. The dynamic programming method is much more efficient than the normal nonlinear programming method. Convergence is obtained even if poor initial control rod positions are given.
文摘功率控制系统(Power Control System,PCS)是反应堆控制系统(Reactor Control System,RCS)的重要组成部分,它完成功率提升、功率保持与功率调节的作用。在钍基熔盐堆(Thorium Molten Salt Reactor,TMSR)核能系统固态堆设计方案中,功率控制器根据实测功率与设定功率值之间的偏差和偏差的变化趋势,按照经典的比例-积分-微分(Proportional Integral Derivative,PID)控制算法,给出调节控制棒的运动距离和运动方向等信号。PCS的PID算法设计与基于反应堆中子物理、热工及控制棒的传动性能构成的闭环控制系统的特性有关,其不同参数的确定与系统的静态和动态性能指标的要求相对应。本文从控制的角度出发,在已有的控制棒样机中设计的棒控棒位系统及相关中子物理的基础上对PCS的PID算法进行多层次仿真与参数分析,并对系统的可控性与可测性进行分析验证。分析及仿真结果表明两种控制模型下的系统均是完全可控及完全可测的,在合适的PID参数集下均能体现响应的快速性及系统的良好鲁棒性和抗干扰能力,具有实际的应用意义。
