On the calibration of a shear stress criterion for rock joints to represent the full stress-strain profile

Conventional numerical solutions developed to describe the geomechanical behavior of rock interfaces subjected to differential load emphasize peak and residual shear strengths.The detailed analysis of preand post-peak shear stress-displacement behavior is central to various time-dependent and dynamic rock mechanic problems such as rockbursts and structural instabilities in highly stressed conditions.The complete stress-displacement surface(CSDS)model was developed to describe analytically the pre-and post-peak behavior of rock interfaces under differential loads.Original formulations of the CSDS model required extensive curve-fitting iterations which limited its practical applicability and transparent integration into engineering tools.The present work proposes modifications to the CSDS model aimed at developing a comprehensive and modern calibration protocol to describe the complete shear stressdisplacement behavior of rock interfaces under differential loads.The proposed update to the CSDS model incorporates the concept of mobilized shear strength to enhance the post-peak formulations.Barton’s concepts of joint roughness coefficient(JRC)and joint compressive strength(JCS)are incorporated to facilitate empirical estimations for peak shear stress and normal closure relations.Triaxial/uniaxial compression test and direct shear test results are used to validate the updated model and exemplify the proposed calibration method.The results illustrate that the revised model successfully predicts the post-peak and complete axial stressestrain and shear stressedisplacement curves for rock joints.

Dynamic impact properties of deep sandstone under thermal-hydraulicmechanical coupling loads

The deep rock mass within coal mines situated in a challenging environment are characterized by high ground stress,high geotemperature,high osmotic water pressure,and dynamic disturbances from mechanical excavation.To investigate the impact of this complex mechanical environment on the dynamic characteristics of roof sandstone in self-formed roadways without coal pillars,standard specimens of deep sandstone from the 2611 upper tunnel working face of the Yongmei Company within the Henan Coal Chemical Industry Group in Henan,China were prepared,and an orthogonal test was designed.Using a self-developed geotechnical dynamic impact mechanics test system,triaxial dynamic impact tests under thermal-hydraulicmechanical coupling conditions were conducted on deep sandstone.The results indicate that under high confining pressure,deep sandstone exhibits pronounced brittle failure at low temperatures,with peak strength gradually decreasing as temperature and osmotic water pressure increase.Conversely,under low confining pressure and low temperature,the brittleness of deep sandstone weakens gradually,while ductility increases.Moreover,sandstone demonstrates higher peak strength at low temperatures under high axial pressure conditions,lower peak strength at high temperatures,and greater strain under low axial pressure and high osmotic water pressure.Increases in impact air pressure and osmotic water pressure have proportionally greater effects on peak stress and peak strain.Approximately 50%of the input strain energy is utilized as effective energy driving the sandstone fracture process.Polar analysis identifies the optimal combination of factors affecting the peak stress and peak strain of sandstone.Under the coupling effect,intergranular and transgranular fractures occur within the sandstone.SEM images illustrate that the damage forms range from minor damage with multiple fissures to extensive fractures and severe fragmentation.This study elucidates the varied dynamic impact mechanical properties of deep sandstones under thermal-hydraulic-mechanical coupling,along with multifactor analysis methods and their optimal factor combinations.

ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

EFFECT OF DENTIN TUBULES ON THE MECHANICAL PROPERTIES OF DENTIN. PART Ⅰ: STRESS-STRAIN RELATIONS AND STRENGTH CRITERION

As known, there is a large number of dentin tubules in dentin. These tubules have varying radii and are shaped into radially parallel pattern. The anisotropy of microstructure of dentin shows that dentin should be treated as a ma- terial of varying transverse isotropy. In this Part, the elastic stress-strain relations and the quadratic strength criterion are established in the form of having varying transverse isotropy, in the framework of micromechanics to take into account of the effect of the microstructures-dentin tubules. Simplified forms for isotropic and ho- mogeneous cases, as well as the corresponding plane stress form of the stress-strain relations are also given. These theoretical models are very well supported by the experiments shown later in the continued paper (Part Ⅱ).

Numerical simulation of the stress-strain curve and the stress and strain distributions of the titanium-duplex alloy

The stress-strain curve of an α-β Ti-8Mn alloy was measured and then it was calculated with finite element method （FEM） based on the stress-strain curves of the single α and β phase alloys. By comparing the calculated stress-strain curve with the measured one, it can be seen that they fit each other very well. Thus, the FE model built in this work is effective. According to the above mentioned model, the distributions of stress and strain in the α and β phases were simulated. The results show that the stress gradients exist in both α and β phases, and the distributions of stress are inhomogeneous. The stress inside the phase is generally higher than that near the interface. Meanwhile, the stress in the α phase is lower than that in the β phase, whereas the strain in the α phase is higher than that in the β phase.

Stress-Strain Relationship and Failure Criterion for Concrete after Freezing and Thawing Cycles

The research of the failure criterion and one-dimensional stress-strain relationship of deteriorated concrete were carried out. Based on the damage mechanics theory, the dsmage which reflects the alternation of internal state of material were introduced into the formula presented by Desayi and Krishman and the weighted twin-shear strength theory. As a nondestructive examination method in common use, the ultrasonic technique was adopted in the study, and the ultrasonic velocity was used to establish the damage variable. After that, the failure criterion and one-dimensional stress-strain relationship for deteriorated concrete were obtained. Eventually, tests were carried out to study the evolution laws on the damage. The results show that the more freezing and thawing cycles are, the more apparently the failure surface shrinks. Meanwhile, the comparison between theoretical data and experimental data verifies tile rationality of tile damage-based one-dimensional stress-strain relationship proposed.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

Nonlinear model characterizing stress-strain relationship and permeability change of contact compression fracture at closing stage

Understanding the stress-strain relationship and permeability change for contact compression fracture at closing stage has been a hot issue for a long time.Previous investigations of this topic were mainly focused on experimental tests;however,theoretical approaches were rarely reported.Based on this,this paper focuses on the contact fracture at closing stage when rock is uniaxially loaded,and then a theoretical model is proposed.Based on the change of fracture elasticity modulus,it shows that as crack apertures are gradually reduced in the loading process,the permeability of rock sample will decrease progressively.This scenario shows that theoretical computation matches well with the experimental results.Finally,the effects of ratio of sample size to fracture aperture(n).pore pressure(P),and initial aperture(b) on stress-strain relationship and permeability change for contact compression fracture at closing stage are analyzed.

A Numerical Stress-strain Response Model of All Grades of Concretes under Uniaxial Compression

An important problem facing stress-strain response modeling of concrete is the complexity of the compressive strength grades. 21 groups of speeimens with different cubic compressive strength （56.3- 164.9 MPa ） hate beets numerically analyzed. Using only the compressive strength, a stress-strain response model of different concrete grade was established. The numerical simulation model not only qualitatively reproduces the relationship of uniaxial compressive strength, peak value stress and cubic compressive strength, but realizes the consistence of the ascending branch of stress-strain cunts with different strength grades by introducing the correction coefficient k. The results indicate k increases gradually from 0 to approximate 1 with the increase of the compressive strength, corresponding to the transition from the paracurve to straight line branch in stress-strain curves. When k is 0, the madel is identical to the Hognestad equation. A good agreement with the experiment data was obtained.

Rate dependent rheological stress-strain behavior of porous nanocrystalline materials

To completely understand the rate-dependent stress-strain behavior of the porous nanocrystalline materials,it is necessary to formulate a constitutive model that can reflect the complicated experimentally observed stress-strain relations of nanocrystalline materials.The nanocrystalline materials consisting grain interior and grain boundary are considered as viscoplastic and porous materials for the reasons that their mechanical deformation is commonly governed by both dislocation glide and diffusion,and pores commonly exist in the nanocrystalline materials.A constitutive law of the unified theory reflecting the stress-strain relations was established and verified by experimental data of bulk nanocrystalline Ni prepared by hydrogen direct current arc plasma evaporation method and hot compression.The effect of the evolution of porosity on stress-strain relations was taken into account to make that the predicted results can keep good agreements with the corresponding experimental results.

A Normalized Stress-Strain Model for Soft Clays

-A nonlinear model for the stress-strain behaviour of normally consolidated clays is presented based on the experimental results. It is indicated that the volume strain under pure shear is a power function of stress ratio and the normalized stress-strain curve is a standard hyperbola. According to the model, the coefficient of pore pressure induced by shear stress and the critical stress ratio which governs the influence of the negative dilatancy are suggested. It is shown by some triaxial tests that the proposed model can be used to study the negative dilatancy and to describe the stress-strain-pore pressure adequately for soft clays.

Novel Ring Compression Test Method to Determine the Stress-Strain Relations and Mechanical Properties of Metallic Materials

Although there are methods for testing the stress-strain relation and strength,which are the most fundamental and important properties of metallic materials,their application to small-volume materials and tube components is lim-ited.In this study,based on energy density equivalence,a new dimensionless elastoplastic load-displacement model for compressed metal rings with isotropy and constitutive power law is proposed to describe the relations among the geometric dimensions,Hollomon law parameters,load,and displacement.Furthermore,a novel test method was developed to determine the elastic modulus,stress-strain relation,yield and tensile strength via ring compression test.The universality and accuracy of the method were verified within a wide range of imaginary materials using finite element analysis(FEA),and the results show that the stress-strain curves obtained by this method are consistent with those inputted in the FEA program.Additionally,a series of ring compression tests were performed for seven metallic materials.It was found that the stress-strain curves and mechanical properties predicted by the method agreed with the uniaxial tensile results.With its low material consumption,the ring compression test has the potential to be as an alternative to traditional tensile test when direct tension method is limited.

Relations of complete creep processes and triaxial stress-strain curves of rock

Based on the results of triaxial compressive creep tests for five kinds of rock under the different stress loading,unloading and cycle-loading-unloading conditions,the creep deformation is not only a function of stress and time,but also it has the corresponding relations to the triaxial stress-strain curves of rock.The deformation properties of soften-strain,harden-strain and ideal plasticity presented by conventional triaxial compressive test curves under the different stress states were utilized,and the creep characteristics,the creep starting stress and the different entire creep process curves of rock were studied systematically according to creep experiment results,and the relations of the triaxial stress-strain curves to the creeping starting stress,the terminating curve,the different creep processes,and the different creep fracture properties were established.The relations presented in this paper were verified partially by the creep experiment results of five types of rock.

Comprehensive Analysis of Stress-Strain in Typical Metal Forming Processes

ＣｏｍｐｒｅｈｅｎｓｉｖｅＡｎａｌｙｓｉｓｏｆＳｔｒｅｓｓ－ＳｔｒａｉｎｉｎＴｙｐｉｃａｌＭｅｔａｌＦｏｒｍｉｎｇＰｒｏｃｅｓｓｅｓ￥（王仲仁）ＷＡＮＧＺｈｏｎｇｒｅｎ（Ｄｅｐｔ．ｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｅｒｉｎｇ，Ｈａ...

Stress-strain Model of Corroded Concrete under Uniaxial Compressive Loading

The prism specimens of corroded concrete were subjected to uniaxial compressive load to develop the stress-strain model. Compared to the un-corroded concrete, the mechanical prop- erties of corroded concrete, such as peak strength, Young＇s modulus, and residual deformation, et al are degraded. The concrete, which were subjected to the aggressive media in the environment, were resulted in randomly distributed pre-loading flaws and defects. The propagation of these corrosion flaws during the procedure of loading was the main reason of degradation of corroded concrete properties. By the application of the statistic theory of continuum damage, the compressive stress-strain curve of corroded concrete was simulated. The initial damage factor was introduced to represent the corrosive effects of different media. The present damage constitutive model agreed well with the test results.

The relationship between microstructure and stress-strain behavior in tension in high strength pipeline steel

In this paper the relationship between microstructure and stress-strain behavior in tensile test of high strength pipeline steel was investigated.The steel with polygonal ferrite-bainite(PF + B) microstructure has a "round-house" type tensile stress-strain curve with low Y/T ratio,highly uniform elongation and high n-value,which means PF + B microstructure has the best deformability(i.e.Ideal stress-strain behavior) among the four microstructures.The steel with acicular ferrite-martensite&austenite(AF + MA) microstructure has a "continuous-yielding" type tensile stress-strain curve,whose deformability is worse than that of PF + B microstructure.Both the steels of polygonal ferrite-acicular ferrite(PF + AF) and polygonal ferrite-pearlite (PF+P) microstructure have "luders elongation" type tensile stress-strain curve with high Y/T ratio,low uniform elongation and low n-value,which means PF + AF and PF + P microstructures have the worst deformability among the four microstructures.

MODELLING OF TENSILE STRESS-STRAIN CURVE OF WOVEN FABRICS

A general shape of tensile stress-strain curves of woven fabrics is first recognised by puttingtested and predicted results together.An exponential function with two parameters is then selectedfor the prediction of tensile stress-strain relationship.The predicted results by using the proposedfunction show excellent agreement with experimental data.

ANALYSIS OF THE LOCALIZATION OF DAMAGE AND THE COMPLETE (STRESS-STRAIN) RELATION FOR MESOSCOPIC HETEROGENEOUS ROCK UNDER UNIAXIAL TENSILE LOADING

The mechanical behavior of rock under uniaxial tensile loading is different from that of rock under compressive loads. A micromechanics-based model was proposed for mesoscopic heterogeneous brittle rock undergoing irreversible changes of their microscopic structures due to microcrack growth. The complete stress-strain relation including linear elasticity, nonlinear hardening,rapid stress drop and strain softening was obtained. The influence of all microcracks with different sizes and orientations were introduced into the constitutive relation by using the probability density function describing the distribution of orientations and the probability density function describing the distribution of sizes. The influence of Weibull distribution describing the distribution of orientations and Rayleigh function describing the distribution of sizes on the constitutive relation were researched. Theoretical predictions have shown to be consistent with the experimental results.

ANALYSIS OF THE LOCALIZATION OF DAMAGE AND THE COMPLETE STRESS-STRAIN RELATION FOR MESOSCOPIC HETEROGENEOUS BRITTLE ROCK SUBJECTED TO COMPRESSIVE LOADS

A micromechanics-based model is established. The model takes the interaction among sliding cracks into account, and it is able to quantify the effect of various parameters on the localization condition of damage and deformation for brittle rock subjected to compressive loads. The closed-form explicit expression for the complete stress-strain relation of rock containing microcracks subjected to compressive loads was obtained. It is showed that the complete stress-strain relation includes linear elasticity,nonlinear hardening,rapid stress drop and strain softening.The behavior of rapid stress drop and strain softening is due to localization of deformation and damage. Theoretical predictions have shown to be consistent with the experimental results.