Impact of well placement and flow rate on production efficiency and stress field in the fractured geothermal reservoirs

Geothermal energy has gained wide attention as a renewable alternative for mitigating greenhouse gas emissions.The advancements in enhanced geothermal system technology have enabled the exploitation of previously inaccessible geothermal resources.However,the extraction of geothermal energy from deep reservoirs poses many challenges due to high‐temperature and high‐geostress conditions.These factors can significantly impact the surrounding rock and its fracture formation.A comprehensive understanding of the thermal–hydraulic–mechanical(THM)coupling effect is crucial to the safe and efficient exploitation of geothermal resources.This study presented a THM coupling numerical model for the geothermal reservoir of the Yangbajing geothermal system.This proposed model investigated the geothermal exploitation performance and the stress distribution within the reservoir under various combinations of geothermal wells and mass flow rates.The geothermal system performance was evaluated by the criteria of outlet temperature and geothermal productivity.The results indicate that the longer distance between wells can increase the outlet temperature of production wells and improve extraction efficiency in the short term.In contrast,the shorter distance between wells can reduce the heat exchange area and thus mitigate the impact on the reservoir stress.A larger mass flow rate is conducive to the production capacity enhancement of the geothermal system and,in turn causes a wider range of stress disturbance.These findings provide valuable insights into the optimization of geothermal energy extraction while considering reservoir safety and long‐term sustainability.This study deepens the understanding of the THM coupling effects in geothermal systems and provides an efficient and environmentally friendly strategy for a geothermal energy system.

Analysis of Modeling the Influence of Electromagnetic Fields Radiated by Industrial Static Converters and Impacts on Operators Using Maxwell’s Equations

The study of Electromagnetic Compatibility is essential to ensure the harmonious operation of electronic equipment in a shared environment. The basic principles of Electromagnetic Compatibility focus on the ability of devices to withstand electromagnetic disturbances and not produce disturbances that could affect other systems. Imperceptible in most work situations, electromagnetic fields can, beyond certain thresholds, have effects on human health. The objective of the present article is focused on the modeling analysis of the influence of geometric parameters of industrial static converters radiated electromagnetic fields using Maxwell’s equations. To do this we used the analytical formalism for calculating the electromagnetic field emitted by a filiform conductor, to model the electromagnetic radiation of this device in the spatio-temporal domain. The interactions of electromagnetic waves with human bodies are complex and depend on several factors linked to the characteristics of the incident wave. To model these interactions, we implemented the physical laws of electromagnetic wave propagation based on Maxwell’s and bio-heat equations to obtain consistent results. These obtained models allowed us to evaluate the spatial profile of induced current and temperature of biological tissue during exposure to electromagnetic waves generated by this system. The simulation 2D results obtained from computer tools show that the temperature variation and current induced by the electromagnetic field can have a very significant influence on the life of biological tissue. The paper provides a comprehensive analysis using advanced mathematical models to evaluate the influence of electromagnetic fields. The findings have direct implications for workplace safety, potentially influencing standards and regulations concerning electromagnetic exposure in industrial settings.

Enhancing economic sustainability in mature oil fields:Insights from the clustering approach to select candidate wells for extended shut-in

Fluctuations in oil prices adversely affect decision making situations in which performance forecasting must be combined with realistic price forecasts.In periods of significant price drops,companies may consider extended duration of well shut-ins(i.e.temporarily stopping oil production)for economic reasons.For example,prices during the early days of the Covid-19 pandemic forced operators to consider shutting in all or some of their active wells.In the case of partial shut-in,selection of candidate wells may evolve as a challenging decision problem considering the uncertainties involved.In this study,a mature oil field with a long(50+years)production history with 170+wells is considered.Reservoirs with similar conditions face many challenges related to economic sustainability such as frequent maintenance requirements and low production rates.We aimed to solve this decision-making problem through unsupervised machine learning.Average reservoir characteristics at well locations,well production performance statistics and well locations are used as potential features that could characterize similarities and differences among wells.While reservoir characteristics are measured at well locations for the purpose of describing the subsurface reservoir,well performance consists of volumetric rates and pressures,which are frequently measured during oil production.After a multivariate data analysis that explored correlations among parameters,clustering algorithms were used to identify groups of wells that are similar with respect to aforementioned features.Using the field’s reservoir simulation model,scenarios of shutting in different groups of wells were simulated.Forecasted reservoir performance for three years was used for economic evaluation that assumed an oil price drop to$30/bbl for 6,12 or 18 months.Results of economic analysis were analyzed to identify which group(s)of wells should have been shut-in by also considering the sensitivity to different price levels.It was observed that wells can be characterized in the 3-cluster case as low,medium and high performance wells.Analyzing the forecasting scenarios showed that shutting in all or high-and medium-performance wells altogether results in better economic outcomes.The results were most sensitive to the number of active wells and the oil price during the high-price period.This study demonstrated the effectiveness of unsupervised machine learning in well classification for operational decision making purposes.Operating companies may use this approach for improved decision making to select wells for extended shut-in during low oil-price periods.This approach would lead to cost savings especially in mature fields with low-profit margins.

Electromagnetic holographic sensitivity field of two-phase flow in horizontal wells

Electromagnetic holographic data are characterized by two modes, suggesting that image reconstruction requires a dual-mode sensitivity field as well. We analyze an electromagnetic holographic field based on tomography theory and Radon inverse transform to derive the expression of the electromagnetic holographic sensitivity field （EMHSF）. Then, we apply the EMHSF calculated by using finite-element methods to flow simulations and holographic imaging. The results suggest that the EMHSF based on the partial derivative of radius of the complex electric potential φ is closely linked to the Radon inverse transform and encompasses the sensitivities of the amplitude and phase data. The flow images obtained with inversion using EMHSF better agree with the actual flow patterns. The EMHSF overcomes the limitations of traditional single-mode sensitivity fields.

On the Bacteriostatic Activity of Bacillus subtilis and Pyraclostrobin as Well as Their Mixtures to Grape Anthracnose and the Field Disease Control Efficiency

[Objective] To screen out the biological compound bactericides for grape anthracnose, reduce and replace the use of chemical pesticide. [Methods] The de- termination on the indoor bacteriostatic activity of different proportions of Bacillus subtilis and pyraclostrobin to grape anthracnose was carried out, and mycelial growth rate method was adopted to determine the toxicity of Bacillus subtilis and pyraclostrobin as well as their 5 mixtures to grape anthracnose. [Results] The EC50 of Bacillus subtilis and pyraclostrobin as well as their mixture combinations of 1：1, 1：2, 1：3, 1：4 and 1：5 to grape anthracnose were respectively 1.969 8, 1.527 4, 1.373 2, 1.294 8 and 1.247 3 μg/ml; the synergistic coefficients （SR） of the 5 mix- ture combinations to grape anthracnose were 1.70, 1.25, 1.13, 1.12 and 1.12, re- spectively, in which the synergistic effect of 1：1 was the largest. The indoor biologi- cal activity of pyraclostrobin（EC50 was 1.054 0μg/ml） was higher than that of Bacil- lus subtilis（EC50 was 15.017 5 μg/ml）. 50 d after the agentia（before the harvesting）, the investigation results showed that 1 000-fold dilution, 1 500-fold dilution and 2 000- fold dilution as well as each single dosage of 20% pyraclostrobin .200×10^8 cfu/g Bacillus subtili wettable powder all had better control efficiency to grape anthracnose after fruit setting and before bagging, in which the treatments of high concentration and middle concentration were higher than the treatments of low concentration and two single dosages： the highest control efficiency of high concentration was 90.03%, which was higher than all other treatments; the control efficiency of middle concen- tration was 87.01%, which was higher than that of low concentration and each sin- gle dosage; the control efficiency of low concentration was 84.11%, which was high- er than 1 000-fold dilution of 1 000×10^8 cfu/g Bacillus subti/i wettable powder （the control efficiency was 64.60%） and 2 000-fold dilution of 250 g/L Bacillus subti/i wettable powder （the control efficiency was 81.07%）. In addition, each treatment al- so had better control efficiency to other cluster diseases, such as white rot, etc., and the control efficiency was almost the same as that of anthracnose. [Conclusion] It was suggested that the prevention concentration of 20% pyraclostrobin .200×10^8 cfu/g Bacillus subtili wettable powder to grape anthracnose after fruit setting and before bagging was 1 000-fold - 2 000-fold dilution.

Bound Polaron in a Quantum Well Under an Electric Field

We conduct a theoretical study on the properties of a bound polaron in a quantum well under an electric field using linear combination operator and unitary transformation methods, which are valid in the whole range of electron-LO phonon coupling. The changing relations between the ground-state energy of the bound polaron in the quantum well and the Coulomb bound potential, the electric field strength, and the well width are derived. The numerical results show that the ground-state energy increases with the increase of the electric field strength and the Coulomb bound potential and decreases as the well width increases.

Influence of Polarization-Induced Electric Fields on Optical Properties of Intersubband Transitions in Al_xGa_(1-x)N/GaN Double Quantum Wells

The influence of polarization-induced electric fields on the electron distribution and the optical properties of intersubband transitions （ISBT） in AlxGa（1-x）N/GaN coupled double quantum wells （DQWs） is investigated by self-consistent calculation. It is found that the polarization-induced potential drop leads to an asymmetric potential profile of AlxGa（1-x）N/GaN DQWs even though the two wells have the same width and depth. The polarization effects result in a very large Stark shift between the odd and even order subbands,thus shortening the wavelength of the ISBT between the first odd order and the second even order （1odd-2 ） subbands. Meanwhile, the electron distribution becomes asymmetric due to the polarization effects, and the absorption coefficient of the 1odd-2 ISBT decreases with increasing polarization field discontinuity.

Numerical simulation of wellbore and formation temperature fields in carbonate formations during drilling and shut-in in the presence of lost circulation

Temperature curves reflect geothermal gradients and local temperature anomalies, thus providing a new understanding of the underground reservoir conditions. When encountering caverns or fractures and fissures during drilling, lost circulation may occur and result in a change to the original formation temperature field, and in severe cases, even the conventional open hole well logging data cannot be obtained. This paper uses finite element analysis software COMSOL to establish a heat transfer model for the wellbore/reservoir formation system during drilling and shut-in in the presence of lost circulation, and a case study is made in a carbonate reservoir in the Tahe oilfield. On the basis of the above, we analyze the temperature distribution in the leakage zone, and the studies have shown that the leakage and petrophysical properties have an impact on the temperature of the wellbore and formation, hence we can estimate the reservoir permeability using the temperature data. In addition, the determination of the temperature recovery time after some drilling fluids have leaked into the formation will help in recognizing the subsurface temperature field of the carbonate formation correctly, thus enhancing production logging interpretation accuracy and improving the understanding of later measurements.

Tunneling between double wells of atom in crossed electromagnetic fields

The tunneling between double wells of atom in crossed electromagnetic fields is investigated by a one-dimensional Hamiltonian model. The crossed fields induced outer well is apart from the nuclear origin and it is very difficult to access by means of spectroscopy but it will be possible if there exists the tunneling of the electron between the outer well and the Coulomb potential predominated well at the nuclear origin. A one-dimensional quantum calculation with B-spline basis has been performed for hydrogen atom in crossed fields accessible in our laboratory, at B = 0.8 T and F = -220 V.cm^-1. The calculation shows that the wavefunctions of some excited states close to the Stark saddle point in the outer well extend over to the Coulomb potential well, making it possible to penetrate the quantum information of the outer well. However, the tunneling rate is very small and the spectral measurement of the transitions from the ground state should be of a high resolution and high sensitivity.

A Quantitative Evaluation of Shale Gas Content in Different Occurrence States of the Longmaxi Formation: A New Insight from Well JY-A in the Fuling Shale Gas Field,Sichuan Basin

Comprehensive quantitative evaluation of shale gas content and the controlling factors in different occurrence states is of great significance for accurately assessing gas-bearing capacity and providing effective well-production strategies. A total of 122 core samples from well JY-A in the Fuling shale gas field were studied to reveal the characteristics of S_1 l shale,15 of which were selected to further predict the shale gas content in different occurrence states, which are dependent on geological factors in the thermal evolution process. Geological parameters were researched by a number of laboratory programs, and the factors influential in controlling shale gas content were extracted by both PCA and GRA methods and prediction models were confirmed by the BE method using SPSS software. Results reveal that the adsorbed gas content is mainly controlled by TOC, Ro, SSA, PD and pyrite content, and the free gas content is mainly controlled by S_2, quartz content, gas saturation and formation pressure for S_1 l in well JY-A. Three methods, including the on-site gas desorption method, the empirical formula method, and the multiple regression analysis method were used in combination to evaluate the shale gas capacity of well JY-A, all of which show that the overall shale gas content of well JY-A is in the range of 2.0–5.0 m^3/t and that the free gas ratio is about 50%, lower than that of well JY-1. Cause analysis further confirms the tectonics and preservation conditions of S_1 l in the geological processes, especially the influence of eastern boundary faults on well JY-A, as the fundamental reasons for the differences in shale gas enrichment in the Jiaoshiba area.

Built-in electric field effect on cyclotron mass of magnetopolarons in a wurtzite In_xGa_(1-x)N/GaN quantum well

The cyclotron mass of magnetopolarons in wurtzite InxGa1-xN/GaN quantum well is studied in the presence of an external magnetic field by using the Larsen perturbation method. The effects of the built-in electric field and different phonon modes including interface, confined and half-space phonon modes are considered in our calculation. The results for a zinc-blende quantum well are also given for comparison. It is found that the main contribution to the transition energy comes from half-space and interface phonon modes when the well width is very small while the confined modes play a more important role in a wider well due to the location of the electron wave function. As the well width increases, the cyclotron mass of magnetopolarons first increases to a maximum and then decreases either with or without the built-in electric field in the wurtzite structure and the built-in electric field slightly reduces the cyclotron mass. The variation of cyclotron mass in a zinc-blende structure is similar to that in a wurtzite structure. With the increase of external magnetic field, the cyclotron mass of polarons almost linearly increases. The cyclotron frequency of magnetopolarons is also discussed.

Input signal design to estimate interwell connectivities in mature fields from the capacitance-resistance model

Interwell connectivities are fundamental parameters required to manage waterfloods in oil reservoirs. Data-driven models, such as the capacitance-resistance model （CRM）, are fast tools to estimate these parameters from time-correlations of input （injection rates） and output （production rates） signals. Noise and structure of the input time-series impose limits on the information that can be extracted from a given data-set. This work uses the CRM to study general prescriptions for the design of input signals that enhance the information content of injection/production data in the estimation of well-to-well interactions. Numerical schemes and general features of the optimal input signal strategy are derived for this problem.

Development Strategies for Achieving High Production with Fewer Wells in Conventional Offshore Heavy Oil Fields in Bohai Bay,China

Development strategy for heavy-oil reservoirs is one of the important research interests in China National Offshore Oil Corp. （CNOOC） that plans a highly effective development for heavy oil fields in multilayered fluvial reservoirs because of their significant influence on marine oil and even on China＇s petroleum production. The characteristics analysis of multilayered fluvial reservoirs in the heavy oil fields in Bohai Bay indicates that large amounts ofoil were trapped in the channel, point bar and channel bar sands. The reserves distribution of 8 oilfields illustrates that the reserves trapped in the main sands, which is 20%-40% of all of the sand bodies, account for 70%-90% of total reserves of the heavy oil fields. The cumulative production from high productivity wells （50% of the total wells） was 75%-90% of the production of the overall oilfield, while only 3%-10% of the total production was from the low productivity wells （30% of the total wells）. And the high productivity wells were drilled in the sands with high reserves abundance. Based on the above information the development strategy was proposed, which includes reserves production planning, selection of well configuration, productivity design, and development modification at different stages.

Evaluation of polarization field in InGaN/GaN multiple quantum well structures by using electroluminescence spectra shift

In order to investigate the inherent polarization intensity in InGaN/GaN multiple quantum well(MQW) structures,the electroluminescence(EL) spectra of three samples with different GaN barrier thicknesses of 21.3 nm, 11.4 nm, and 6.5 nm are experimentally studied. All of the EL spectra present a similar blue-shift under the low-level current injection,and then turns to a red-shift tendency when the current increases to a specific value, which is defined as the turning point.The value of this turning point differs from one another for the three InGaN/GaN MQW samples. Sample A, which has the GaN barrier thickness of 21.3 nm, shows the highest current injection level at the turning point as well as the largest value of blue-shift. It indicates that sample A has the maximum intensity of the polarization field. The red-shift of the EL spectra results from the vertical electron leakage in InGaN/GaN MQWs and the corresponding self-heating effect under the high-level current injection. As a result, it is an effective approach to evaluate the polarization field in the InGaN/GaN MQW structures by using the injection current level at the turning point and the blue-shift of the EL spectra profiles.

Total Organic Carbon Enrichment and Source Rock Evaluation of the Lower Miocene Rocks Based on Well Logs: October Oil Field, Gulf of Suez-Egypt

October oil field is one of the largest hydrocarbon-bearing fields which produces oil from the sand section of the Lower Miocene Asl Formation. Two marl (Asl Marl) and shale (Hawara Formation) sections of possible source enrichment are detected above and below this oil sand section, respectively. This study aims to identify the content of the total organic carbon based on the density log and a combination technique of the resistivity and porosity logs (Δlog R Technique). The available geochemical analyses are used to calibrate the constants of the TOC and the level of maturity (LOM) used in the (Δlog R Technique). The geochemical-based LOM is found as 9.0 and the calibrated constants of the Asl Marl and Hawara Formation are found as 11.68, 3.88 and 8.77, 2.80, respectively. Fair to good TOC% content values (0.88 to 1.85) were recorded for Asl Marl section in the majority of the studied wells, while less than 0.5% is recorded for the Hawara Formation. The lateral distribution maps show that most of the TOC% enrichments are concentrated at central and eastern parts of the study area, providing a good source for the hydrocarbons encountered in the underlying Asl Sand section.

Adaptability Study of Intelligent Well Systems in East China Sea Oil Field

Intelligent well system is the well that has a set of equipment fixed in the down hole including sensing devices, data transmission system and operating devices for information acquiring, data gathering and decision analysis. By this remote control process, the smart well system can ultimately optimize well deliverability; it is used more and more often in oil fields with its stability and control technique. At present, the main intelligent well systems in the worm include SCRAMS, Direct Hydraulic, Digital Hydraulic that belongs to WellDynamics Company, InForce and InCharge that belongs to Baker Oil Tools Company, RMC that belongs to Schlumberger Company. This paper compares different types of systems and their characteristics, recommending the InCharge system as the intelligent well system for East China Sea Oil Field according to its geological and reservoir conditions.

Binding energy of the donor impurities in GaAs-Ga_(1-x)Al_xAs quantum well wires with Morse potential in the presence of electric and magnetic fields

The behavior of a donor in the GaAs–GaAlAs quantum well wire represented by the Morse potential is examined within the framework of the effective-mass approximation. The donor binding energies are numerically calculated for with and without the electric and magnetic fields in order to show their influence on the binding energies. Moreover, how the donor binding energies change for the constant potential parameters(De, re, and a) as well as with the different values of the electric and magnetic field strengths is determined. It is found that the donor binding energy is highly dependent on the external electric and magnetic fields as well as parameters of the Morse potential.

Optical response of an inverted InAs/GaSb quantum well in an in-plane magnetic field

The optical response of an inverted InAs/GaSb quantum well is studied theoretically. The influence of an in-plane magnetic field that is applied parallel to the quantum well is considered. This in-plane magnetic field will induce a dynamical polarization even when the electric field component of the external optical field is parallel to the quantum well.The electron-electron interaction in the quantum well system will lead to the de-polarization effect. This effect is found to be important and is taken into account in the calculation of the optical response. It is found that the main feature in the frequency dependence of the velocity-velocity correlation function remains when the velocity considered is parallel to the in-plane magnetic field. When the direction of the velocity is perpendicular to the in-plane magnetic field, the depolarization effect will suppress the oscillatory behavior in the corresponding velocity-velocity correlation function. The in-plane magnetic field can change the band structure of the quantum well drastically from a gapped semiconductor to a no-gapped semi-metal, but it is found that the distribution of the velocity matrix elements or the optical transition matrix elements in the wave vector space has the same two-tadpole topology.

Numerical Simulation of Temperature and Stress Fields of Ti-Alloy Thin-well Barrel during Quenching Process

The mathematical models have been established to describe the temperature and stress profiles in T16A14V cylinder during quenching. The residual stress and deformation of the workpiece can be predicted precisely based on ANSYS software. The simulated results show that the temperature of the divided element decreases faster at the edge than that at the internal of the workpiece during quenching from 1050 to 20°C. The largest temperature difference and dimension change in diameter are about 90°C and -0.935%, respectively. The position of largest tensile stress occurs around the edge of the cylinder.

Terahertz field-induced modulations of intersubband absorptions in quantum wells

Nonlinear optical properties of intersubband electrons in a 3-level quantum well under intense terahertz field are investigated by using a density matrix approach. The results show that the terahertz fields with different frequencies cause the distinct modulations of the intersubband absorptions. The terahertz-indueed sideband and Autler-Towns splitting in the absorption spectrum are obtained, respectively for the terahertz-photon energy below and close to the transition energy between the ground and first excited state.