Effects of soil crust on the collapsing erosion of colluvial deposits with granite residual soil

Collapsing erosion is a unique phenomenon commonly observed on the granite residue hillslopes in the tropical and subtropical regions of southern China,characterized by its abrupt occurrence and significant erosion volumes.However,the impacts of soil crust conditions on the erosion of colluvial deposits with granite residual soils have only been studied to a limited extent.To address this issue,this study investigates the impacts of three soil crust conditions(i.e.,without crust,10-minute crust,and 20-minute crust)on gully morphology,rainfall infiltration,and runoff and sediment yield during slope erosion of colluvial deposits with granite residues(classified as Acrisols)in Yudu County,Ganzhou City,Jiangxi Province,China,using simulated rainfall tests and photographic methods.The results showed that as the strength of the soil crust increased,the capacity of moisture infiltration and the width and depth of the gully as well as the sediment concentration and yield ratio decreased;at the same time,the runoff ratio increased.The sediment yield in the without-crust test was found to be 1.24 and 1.43 times higher than that observed in the 10-minute crust and 20-minute crust tests,respectively.These results indicate that soil crusts can effectively prevent slope erosion and moisture infiltration,while providing valuable insights for the management of soil erosion in natural environments.

Effect of petroleum chemical fraction and residual oil content in saline lacustrine organic-rich shale: A case study from the Paleogene Dongpu Depression of North China

Halite and gypsum minerals in saline shale make the retention mechanism and chemical fractionation of residual oil unique. The Dongpu Depression in North China is a typically saline lacustrine basin with developing halite and gypsum. The effect of gypsum minerals on residual oil content and chemical fractionation remains unclear. In this study, shale samples with different gypsum contents were used in organic geochemical experiments, showing that the high total organic matter (TOC) content and type II kerogen leads to a high residual oil content, as shown by high values of volatile hydrocarbon (S1) and extractable organic matter (EOM). XRD and FE-SEM result indicate that the existence of gypsum in saline shale contributes to an enhanced pore space and a higher residual oil content in comparison to non-gypsum shale. Additionally, the increase in the gypsum mineral content leads to an increase in the saturated hydrocarbon percentage and a decrease in polar components percentage (resins and asphaltene). Furthermore, thermal simulation experiments on low-mature saline shale show that the percentage of saturated hydrocarbons in the residual oil is high and remains stable and that the storage space is mainly mesoporous (> 20 nm) in the oil expulsion stage. However, the saturated hydrocarbons percentage decreases rapidly, and oil exists in mesopores (> 20 nm and < 5 nm) in the gas expulsion stage. In general, gypsum is conducive to the development of pore space, the adsorption of hydrocarbons and the occurrence of saturated hydrocarbon, leading to large quantities of residual oil. The data in this paper should prove to be reliable for shale oil exploration in saline lacustrine basins.

Utilization mechanism of foam flooding and distribution situation of residual oil in fractured-vuggy carbonate reservoirs

The development of fractured-vuggy carbonate reservoirs is extremely difficult because of the complex fractured-vuggy structure and strong heterogeneity.Foam flooding is a potential enhanced oil recovery(EOR)technology in fractured-vuggy carbonate reservoirs.Based on the similarity criterion,three types of 2D visual physical models of the fractured-vuggy structure were made by laser ablation technique,and a 3D visual physical model of the fractured-vuggy reservoir was made by 3D printing technology.Then the physical analog experiments of foam flooding were carried out in these models.The experimental results show that foam can effectively improve the mobility ratio,control the flow velocity of the fluid in different directions,and sweep complex fracture networks.The effect of foam flooding in fractures can be improved by increasing foam strength and enhancing foam stability.The effect of foam flooding in vugs can be improved by reducing the density of the foam and the interfacial tension between foam and oil.Three types of microscopic residual oil and three types of macroscopic residual oil can be displaced by foam flooding.This study verifies the EOR of foam flooding in the fractured-vuggy reservoir and provides theoretical support for the application of foam flooding in fractured-vuggy reservoirs.

Reservoir heterogeneity controls of CO_(2)-EOR and storage potentials in residual oil zones:Insights from numerical simulations

Residual oil zones(ROZs)have large potential for CO_(2)enhanced oil recovery(EOR)and geologic storage.During CO_(2)injection,the migration of CO_(2)in ROZs controls the performance of both EOR and storage.However,it has not been clearly visualized and understood that how geological heterogeneity factors control the transport of CO_(2)in ROZs.In this study,the oil recovery performance and geologic storage potential during continuous CO_(2)injection in a representative ROZ are studied based on geostatistical modelling and high-fidelity three-phase flow simulation.We examined the influence of autocorrelation length of permeability,global heterogeneity(DykstraeParsons coefficient),and permeability anisotropy on cumulative oil recovery and CO_(2)retention fraction.Simulation results indicate that,as the permeability autocorrelation length increases,the cumulative oil recovery and CO_(2)storage efficiency decrease.This results from the accelerated migration of CO_(2)along high permeability zones(i.e.,gas channeling).The increase in global heterogeneity and permeability anisotropies can lead to low oil recovery and poor CO_(2)sequestration performance,depending on the degree of CO_(2)channeling.The net utilization ratio of CO_(2)(CO_(2)retained/oil produced)unfavorably increases with both autocorrelation length and Dykstra eParsons coefficient,but decreases with the increase in kv/kh.Such a decrease is attributed to enlarged swept volume induced by gravity override.The study provides important implications for fieldscale CO_(2)EOR and storage applications in ROZs.

Numerical analysis of water-alternating-CO_(2) flooding for CO_(2)-EOR and storage projects in residual oil zones

Residual oil zones(ROZs)have high residual oil saturation,which can be produced using CO_(2) miscible flooding.At the same time,these zones are good candidates for CO_(2) sequestration.To evaluate the coupled CO_(2)-EOR and storage perfor-mance in ROZs for Water-Alternating-CO_(2)(WAG)flooding,a multi-compositional CO_(2) miscible model with molecular diffusion was developed.The effects of formation parameters(porosity,permeability,temperature),operation parameters(bottom hole pressure,WAG ratio,pore volume of injected water),and diffusion coeffcient on the coupled CO_(2)-EOR and storage were investigated.Five points from the CO_(2) sequestration curve and the oil recovery factor curve were selected to help better analyze coupled CO_(2)-EOR and storage.The results demonstrate that enhanced performance is observed when formation permeability is higher and a larger volume of water is injected.On the other hand,the performance diminishes with increasing porosity,molecular diffusion of gas,and the WAG ratio.When the temperature is around 100℃,coupled CO_(2)-EOR and storage performance is the worst.To achieve optimal miscible flooding,it is recommended to maintain the bottom hole pressure(BHP)of the injection well above 1.2 minimum miscibility pressure(MMP),while ensuring that the BHP of the production well remains sufficiently high.Furthermore,the tapered WAG flooding strategy proves to be profitable for enhanced oil recovery,as compared to a WAG ratio of 0.5:1,although it may not be as effective for CO_(2) sequestration.

CO_(2) gas stripped off membranous residual oil from pore surfaces: Effects of temperature, pressure and wettability

The threshold values of CO_(2) gas stripped off membranous residual oil from the pore walls are not clear under different temperatures, pressures and wettability conditions. The extent to which temperature, pressure and wettability influence CO_(2) flooding for enhancing the recovery of residual oil in membranous formations also remains uncertain. Therefore, further quantitative characterization is entailed. In this study, the molecular dynamics method was employed to explore CO_(2) flooding under different temperatures, pressures and wettability conditions, aiming to enhance the production of membranous residual oil. The results reveal that the interaction energy between CO_(2), decane molecules and pore walls exhibits a decrease with increasing temperature and an increase with increasing pressure, respectively, in distinct wettability scenarios. When the temperature was at or below 363 K and the pressure was not lower than 40 MPa, CO_(2) gas could detach the membranous residual oil from the pore walls in the water-wet systems. When the temperature was equal to 363 K and the pressure remained under 40 MPa, or the temperature surpassed 363 K, CO_(2) gas failed to detach the membranous residual oil from the pore walls in the water-wet systems. For the mixed-wet and oil-wet systems, CO_(2) molecules could not detach the membranous residual oil from the pore walls. The hierarchy of influence regarding temperature, pressure and wettability on the competitive adsorption capacity of CO_(2) and decane molecules on the pore walls emerged as follows: wettability > temperature > pressure. The findings of this study offer valuable insights into the application of CO_(2) gas flooding for the exploitation of membranous residual oil on pore walls.

Structural properties of residual carbon in coal gasification fine slag and their influence on flotation separation and resource utilization:A review

Coal gasification fine slag(FS)is a typical solid waste generated in coal gasification.Its current disposal methods of stockpil-ing and landfilling have caused serious soil and ecological hazards.Separation recovery and the high-value utilization of residual carbon(RC)in FS are the keys to realizing the win-win situation of the coal chemical industry in terms of economic and environmental benefits.The structural properties,such as pore,surface functional group,and microcrystalline structures,of RC in FS(FS-RC)not only affect the flotation recovery efficiency of FS-RC but also form the basis for the high-value utilization of FS-RC.In this paper,the characteristics of FS-RC in terms of pore structure,surface functional groups,and microcrystalline structure are sorted out in accordance with gasification type and FS particle size.The reasons for the formation of the special structural properties of FS-RC are analyzed,and their influence on the flotation separation and high-value utilization of FS-RC is summarized.Separation methods based on the pore structural characterist-ics of FS-RC,such as ultrasonic pretreatment-pore-blocking flotation and pore breaking-flocculation flotation,are proposed to be the key development technologies for improving FS-RC recovery in the future.The design of low-cost,low-dose collectors containing polar bonds based on the surface and microcrystalline structures of FS-RC is proposed to be an important breakthrough point for strengthening the flotation efficiency of FS-RC in the future.The high-value utilization of FS should be based on the physicochemical structural proper-ties of FS-RC and should focus on the environmental impact of hazardous elements and the recyclability of chemical waste liquid to es-tablish an environmentally friendly utilization method.This review is of great theoretical importance for the comprehensive understand-ing of the unique structural properties of FS-RC,the breakthrough of the technological bottleneck in the efficient flotation separation of FS,and the expansion of the field of the high value-added utilization of FS-RC.

Effects of residual plastic film on crop yield and soil fertility in a dryland farming system

Plastic film mulch in agricultural production becomes essential to maintaining crop yields in arid and semiarid areas.However,the presence of residual film in farmland soil has also drawn much attention.In this study,three experiments were conducted.The first two experimental designs included 0,450,1350,and 2700 kg ha^(-1) of residual film pieces of approximately 5 cm side length added to field soil(0-20 cm soil depth)for seven years and added to pots for four years.In the third experiment,1350 kg ha^(-1)of the residual film with different side lengths(2-5,5-10,10-15,and 15-20 cm)was added to field soil for six years to explore the effect of residual film fragment size on soil nutrients,soil microorganisms,crop growth and yields.The residual film had little effect on the soil moisture at a field depth of 0-2(or 0-1.8)m.There were no significant effects on organic carbon,total nitrogen,inorganic nitrogen,total phosphorus or available phosphorus in the 0-20 cm soil layer.The presence of residual film decreased the richness and diversity of the bacterial community of the surface soil of the residual film,but it had no significant effect on the microbial community of the non-surface soil.The emergence rates of wheat and lentils occasionally decreased significantly with different amounts of residue fragments added to the field.At 450-2700 kg ha^(-1),the residual film reduced the plant height and stem diameter of maize and significantly reduced the shoot biomass of harvested maize by 11-19%.The average yields of maize and potato over the seven years decreased,but there were almost no significant statistical differences among the treatments.These results provide important data for a comprehensive scientific understanding of the effects of residual film on soil and crops in dryland farming systems.

Mesoscopic measurement of damage and shear bands of granite residual soil using Micro-CT and digital volume correlation

The mesomechanics of geotechnical materials are closely related to the macromechanical properties,especially the mesoscale evolution of shear bands,which is helpful for understanding the failure mechanism of geotechnical materials.However,there is lack of effective quantitative analysis method for the complex evolution mechanism of threedimensional shear bands.In this work,we used X-ray computed tomography(CT)to reconstruct volume images and used the digital volume correlation(DVC)method to calculate the three-dimensional strain fields of granite residual soil samples at different loading stages.The trend of the failure surface of the shear bands was obtained by the planar fitting method,and the connectivity index was constructed according to the projection characteristics of the shear bands on the failure trend surface.The results support the following findings:the connectivity index of the shear band increases rapidly and then slowly with increasing axial strain,which is characterized by a near'S'curve.As the stress reaches the peak value,the connectivity index of the shear bands almost exceeds 0.7.The contribution of the new shear band volume to the connectivity of the shear bands becomes increasingly small with increasing axial loading.Affected by quartz grains and stress at the initial stage,the dip angle gradually and finally approaches the included angle of the maximum shear stress from the discrete state with increasing axial loading.The tendency and dip angle of the resulting shear bands are dynamic,and the tendency slightly deflects with increasing loading.

A Model for the Determination of Semi-Circular Spot Corrosion Damage and Residual Strength in Oil Pipes

Pitting corrosion often occurs due to the presence of various corrosive substances,such as CO_(2) and H_(2)S,in the pipe service environment.As a result of this process,the residual strength of oil pipes is reduced and this can compromise the integrity of the entire pipe string.In the present work,a model is introduced on the basis of the API579 standard to determine the so-called stress concentration coefficient.The model accounts for pitting corrosion shapes such as shallow semi-circles,semi-circles,and deep semi-circles.The relationship between the corrosion pit depth and opening diameter and the residual strength of the oil casing is obtained.The results show that the influence of the pit opening diameter on the stress concentration coefficient is smaller than that of the pit depth.For a constant pit opening diameter,the coefficient increases gradually with increasing the pit depth.The compressive strength and internal pressure strength of the carbon steel oil casing decrease accordingly.When the depth of the corrosion pit is relatively small,the growth of the coefficient is slower;when the depth of the corrosion pit increases to a certain value,the increase in stress concentration coefficient becomes obvious.

Geochemical characteristics and exploration significance of ultra-deep Sinian oil and gas from Well Tashen 5,Tarim Basin,NW China

The Well Tashen 5(TS5),drilled and completed at a vertical depth of 9017 m in the Tabei Uplift of the Tarim Basin,NW China,is the deepest well in Asia.It has been producing both oil and gas from the Sinian at a depth of 8780e8840 m,also the deepest in Asia in terms of oil discovery.In this paper,the geochemical characteristics of Sinian oil and gas from the well were investigated and compared with those of Cambrian oil and gas discovered in the same basin.The oil samples,with Pr/Ph ratio of 0.78 and a whole oil carbon isotopic value of31.6‰,have geochemical characteristics similar to those of Ordovician oils from the No.1 fault in the North Shuntuoguole area(also named Shunbei area)and the Middle Cambrian oil from wells Zhongshen 1(ZS1)and Zhongshen 5(ZS5)of Tazhong Uplift.The maturity of light hydrocarbons,diamondoids and aromatic fractions all suggest an approximate maturity of 1.5%e1.7%Ro for the samples.The(4-+3-)methyldiamantane concentration of the samples is 113.5 mg/g,indicating intense cracking with a cracking degree of about 80%,which is consistent with the high bottom hole temperature(179℃).The Sinian gas samples are dry with a dryness coefficient of 0.97.The gas is a mixture of kerogen-cracking gas and oil-cracking gas and has Ro values ranging between 1.5%and 1.7%,and methane carbon isotopic values of41.6‰.Based on the equivalent vitrinite reflectance(R_(eqv)=1.51%e1.61%)and the thermal evolution of source rocks from the Cambrian Yu'ertusi Formation of the same well,it is proposed that the Sinian oil and gas be mainly sourced from the Cambrian Yu'ertusi Formation during the Himalayan period but probably also be joined by hydrocarbon of higher maturity that migrated from other source rocks in deeper formations.The discovery of Sinian oil and gas from Well TS5 suggests that the ancient ultra-deep strata in the northern Tarim Basin have the potential for finding volatile oil or condensate reservoirs.

Synergistic anionic/zwitterionic mixed surfactant system with high emulsification efficiency for enhanced oil recovery in low permeability reservoirs

Emulsification is one of the important mechanisms of surfactant flooding. To improve oil recovery for low permeability reservoirs, a highly efficient emulsification oil flooding system consisting of anionic surfactant sodium alkyl glucosyl hydroxypropyl sulfonate(APGSHS) and zwitterionic surfactant octadecyl betaine(BS-18) is proposed. The performance of APGSHS/BS-18 mixed surfactant system was evaluated in terms of interfacial tension, emulsification capability, emulsion size and distribution, wettability alteration, temperature-resistance and salt-resistance. The emulsification speed was used to evaluate the emulsification ability of surfactant systems, and the results show that mixed surfactant systems can completely emulsify the crude oil into emulsions droplets even under low energy conditions. Meanwhile,the system exhibits good temperature and salt resistance. Finally, the best oil recovery of 25.45% is achieved for low permeability core by the mixed surfactant system with a total concentration of 0.3 wt%while the molar ratio of APGSHS:BS-18 is 4:6. The current study indicates that the anionic/zwitterionic mixed surfactant system can improve the oil flooding efficiency and is potential candidate for application in low permeability reservoirs.

Fate of fertilizer nitrogen and residual nitrogen in paddy soil in Northeast China

The relationship between the fate of nitrogen (N) fertilizer and the N application rate in paddy fields in Northeast China is unclear,as is the fate of residual N.To clarify these issues,paddy field and15N microplot experiments were carried out in 2017 and 2018,with N applications at five levels:0,75,105,135 and 165 kg N ha–1(N0,N75,N105,N135 and N165,respectively).15N-labeled urea was applied to the microplots in 2017,and the same amount of unlabeled urea was applied in 2018.Ammonia (NH3) volatilization,leaching,surface runoff,rice yield,the N contents and15N abundances of both plants and soil were analyzed.The results indicated a linear platform model for rice yield and the application rate of N fertilizer,and the optimal rate was 135 kg N ha–1.N uptake increased with an increasing N rate,and the recovery efficiency of applied N (REN) values of the difference subtraction method were 45.23 and 56.98%on average in 2017and 2018,respectively.The RENwas the highest at the N rate of 135 kg ha–1in 2017 and it was insignificantly affected by the N application rate in 2018,while the agronomic efficiency of applied N (AEN) and physiological efficiency of applied N (PEN) decreased significantly when excessive N was applied.N loss through NH3volatilization,leaching and surface runoff was low in the paddy fields in Northeast China.NH3volatilization accounted for 0.81 and 2.99%of the total N application in 2017 and 2018,respectively.On average,the leaching and surface runoff rates were 4.45% and less than 1.05%,respectively,but the apparent denitrification loss was approximately 42.63%.The residual N fertilizer in the soil layer (0–40 cm) was 18.37–31.81 kg N ha–1in 2017,and the residual rate was 19.28–24.50%.Residual15N from fertilizer in the soil increased significantly with increasing N fertilizer,which was mainly concentrated in the 0–10 cm soil layer,accounting for 58.45–83.54% of the total residual N,and decreased with increasing depth.While the ratio of residual N in the 0–10 cm soil layer to that in the 0–40 cm soil layer was decreased with increasing N application.Furthermore,of the residual N,approximately 5.4%was taken up on average in the following season and 50.2%was lost,but 44.4%remained in the soil.Hence,the amount of applied N fertilizer should be reduced appropriately due to the high residual N in paddy fields in Northeast China.The appropriate N fertilizer rate in the northern fields in China was determined to be 105–135 kg N ha–1in order to achieve a balance between rice yield and high N fertilizer uptake.

Quantification of the adulteration concentration of palm kernel oil in virgin coconut oil using near-infrared hyperspectral imaging

The adulteration concentration of palm kernel oil(PKO)in virgin coconut oil(VCO)was quantified using near-infrared(NIR)hyperspectral imaging.Nowadays,some VCO is adulterated with lower-priced PKO to reduce production costs,which diminishes the quality of the VCO.This study used NIR hyperspectral imaging in the wavelength region 900-1,650 nm to create a quantitative model for the detection of PKO contaminants(0-100%)in VCO and to develop predictive mapping.The prediction equation for the adulteration of VCO with PKO was constructed using the partial least squares regression method.The best predictive model was pre-processed using the standard normal variate method,and the coefficient of determination of prediction was 0.991,the root mean square error of prediction was 2.93%,and the residual prediction deviation was 10.37.The results showed that this model could be applied for quantifying the adulteration concentration of PKO in VCO.The prediction adulteration concentration mapping of VCO with PKO was created from a calibration model that showed the color level according to the adulteration concentration in the range of 0-100%.NIR hyperspectral imaging could be clearly used to quantify the adulteration of VCO with a color level map that provides a quick,accurate,and non-destructive detection method.

Geological characteristics of unconventional tight oil reservoir (10^(9) t): A case study of Upper Cretaceous Qingshankou Formation, northern Songliao Basin, NE China

The Daqing exploration area in the northern Songliao Basin has great potential for unconventional oil and gas resources,among which the total resources of tight oil alone exceed 109 t and is regarded as an important resource base of Daqing oilfield.After years of exploration in the Qijia area,Songliao Basin,NE China,tight oil has been found in the Upper Cretaceous Qingshankou Formation.To work out tight oil’s geological characteristics,taking tight oil in Gaotaizi oil layers of the Upper Cretaceous Qingshankou Formation in northern Songliao Basin as an example,this paper systematically analyzed the geological characteristics of unconventional tight oil in Gao3 and Gao4 layers of the Qijia area,based on the data of the geological survey,well drilling journey,well logging,and test.It is that three sets of hydrocarbon source rocks(K2qn1,K2qn2+3,and K2n1)develop in the examined area,and exhibit excellent type I and II kerogens,high organic matter abundance,and moderate maturity.The reservoir is generally composed of thin-bedded mudstone,siltstone,and sandstone,and presents poor porosity(average 8.5 vol.%)and air permeability(average 4 mD).The main reservoir space primarily includes intergranular pores,secondary soluble pores,and intergranular soluble pores.Three types of orifice throats were identified,namely fine throat,extra-fine throat,and micro-fine throat.The siltstone is generally oil-bearing,the reservoirs with slime and calcium become worse oil-bearing,and the mudstone has no obvious oil-bearing characteristics.The brittleness indices of the sandstone in the tight oil reservoir range from 40%to 60%,and those of the mudstone range from 40%to 45%,indicating a better brittleness of the tight oil reservoir.Based on the study of typical core hole data,this paper gives a comprehensive evaluation of the properties of the tight oil and establishes a tight oil single well composite bar chart as well as the initial evaluation system with the core of properties in the tight oil reservoir.This study has theoretical guiding significance and practical application value for tight oil exploration and evaluation in the Qijia area.

CO_(2)flooding in shale oil reservoir with radial borehole fracturing for CO_(2)storage and enhanced oil recovery

This study introduces a novel method integrating CO_(2)flooding with radial borehole fracturing for enhanced oil recovery and CO_(2)underground storage,a solution to the limited vertical stimulation reservoir volume in horizontal well fracturing.A numerical model is established to investigate the production rate,reservoir pressure field,and CO_(2)saturation distribution corresponding to changing time of CO_(2)flooding with radial borehole fracturing.A sensitivity analysis on the influence of CO_(2)injection location,layer spacing,pressure difference,borehole number,and hydraulic fractures on oil production and CO_(2)storage is conducted.The CO_(2)flooding process is divided into four stages.Reductions in layer spacing will significantly improve oil production rate and gas storage capacity.However,serious gas channeling can occur when the spacing is lower than 20 m.Increasing the pressure difference between the producer and injector,the borehole number,the hydraulic fracture height,and the fracture width can also increase the oil production rate and gas storage rate.Sensitivity analysis shows that layer spacing and fracture height greatly influence gas storage and oil production.Research outcomes are expected to provide a theoretical basis for the efficient development of shale oil reservoirs in the vertical direction.

Purification of Produced Water from a Sour Oilfield in South Kuwait. 1. Oil-Water Separation and Industrial Salt Production

Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified cellulosic material gained from spent coffee grounds as a tertiary adsorption treatment. The earth-alkaline metal ions and heavy metals were separated from the de-oiled produced water by addition of either sodium or potassium hydroxide in the presence of carbon dioxide or by direct addition of solid sodium carbonate. The resulting filtrate gave salt of industrial purity upon selective crystallization on evaporation.

A review:Health benefits and physicochemical characteristics of blended vegetable oils

Oil blending is the method of choice used worldwide to improve oxidative stability and nutritional value.There is no such edible oil/fat that meets all the recommendations from the health point of view.The fatty acid composition of vegetable oils decides the fate of the oil.Pure single oil is unable to provide a balanced amount of fatty acids(FAs)required/recommended on a daily intake basis.Blending oils/fats is an appropriate procedure of physically mixing multiple oils in suitable proportions which may provide functional lipids with improved antioxidant potential and desirable physical and chemical properties.This review piled up the accessible data on the blending of diverse oils/fats in the combination of binary,ternary,quaternary,or other types of oils into a single blended oil.Blending can be found very convincing towards appropriate FA profile,enhancement in physicochemical characteristics,and augmented stability for the period of storage or when used as cooking/frying processes which could ultimately serve as an effectual dietary intervention towards the health protectiveness.

Experiment of dynamic seepage of tight/shale oil under matrix fracture coupling

A physical simulation method with a combination of dynamic displacement and imbibition was established by integrating nuclear magnetic resonance(NMR)and CT scanning.The microscopic production mechanism of tight/shale oil in pore throat by dynamic imbibition and the influencing factors on the development effect of dynamic imbibition were analyzed.The dynamic seepage process of fracking-soaking-backflow-production integration was simulated,which reveals the dynamic production characteristics at different development stages and their contribution to enhancing oil recovery(EOR).The seepage of tight/shale reservoirs can be divided into three stages:strong displacement and weak imbibition as oil produced rapidly by displacement from macropores and fractures,weak displacement and strong imbibition as oil produced slowly by reverse imbibition from small pores,and weak displacement and weak imbibition at dynamic equilibrium.The greater displacement pressure results in the higher displacement recovery and the lower imbibition recovery.However,if the displacement pressure is too high,the injected water is easy to break through the front and reduce the recovery degree.The higher the permeability,the greater the imbibition and displacement recovery,the shorter the time of imbibition balance,and the higher the final recovery.The fractures can effectively increase the imbibition contact area between matrix and water,reduce the oil-water seepage resistance,promote the oil-water displacement between matrix and fracture,and improve the oil displacement rate and recovery of the matrix.The soaking after fracturing is beneficial to the imbibition replacement and energy storage of the fluid;also,the effective use of the carrying of the backflow fluid and the displacement in the mining stage is the key to enhancing oil recovery.

Cosmetic or Dietary Vegetable Oils Sampled in the Cameroonian Market May Not Expose Consumers to Lipid Oxidation Products Generating Oxidative Stress and Inflammation

Vegetable oils are a source of energy, essential fatty acids, antioxidants and fat-soluble vitamins useful for human health care and development. These oils also contribute to organoleptic quality of their products’ derivatives. However, their chemical and physical properties can be modified by the mode of their extraction, storage and distribution. These modifications might negatively affect the nutritional quality of the oils. The goals of this study were to: sample different vegetable oils for cosmetic or dietary use marketed in Cameroon, and verify purity and oxidation states of each kind of oil through determination of its acidity, iodine, peroxide, saponification, refractive indexes and the conformity of the labeling. The carotene content, the level of polar components and specific absorbance were also determined. As the result, six oils namely palm, palm kernel, coconut, black cumin, peanut and shea butter were collected. Apart from labeling, chemicals and physicals parameters analyzed were generally in accordance with the Cameroonian and Codex Alimentarius standard. This study suggests that vegetable oils sampled in the Cameroonian market may not expose consumers to lipid oxidation products generating pathological oxidative stress and inflammation. However, efforts in application of existing standard need to be done as far as labeling are concerned.