Influence of pressure disturbance wave on dynamic response characteristics of liquid film seal for multiphase pump

Slug flow or high GVF(Gas Volume Fraction)conditions can cause pressure disturbance waves and alternating loads at the boundary of mechanical seals for multiphase pumps,endangering the safety of multiphase pump units.The mechanical seal model is simplified by using periodic boundary conditions and numerical calculations are carried out based on the Zwart-Gerber-Belamri cavitation model.UDF(User Define Function)programs such as structural dynamics equations,alternating load equations,and pressure disturbance equations are embedded in numerical calculations,and the dynamic response characteristics of mechanical seal are studied using layered dynamic mesh technology.The results show that when the pressure disturbance occurs at the inlet,as the amplitude and period of the disturbance increase,the film thickness gradually decreases.And the fundamental reason for the hysteresis of the film thickness change is that the pressure in the high-pressure area cannot be restored in a timely manner.The maximum value of leakage and the minimum value of axial velocity are independent of the disturbance period and determined by the disturbance amplitude.The mutual interference between enhanced waves does not have a significant impact on the film thickness,while the front wave in the attenuated wave has a promoting effect on the subsequent film thickness changes,and the fluctuation of the liquid film cavitation rate and axial velocity under the attenuated wave condition deviates from the initial values.Compared with pressure disturbance conditions,alternating load conditions have a more significant impact on film thickness and leakage.During actual operation,it is necessary to avoid alternating load conditions in multiphase pump mechanical seals.

Stress response characteristics of BFRP anchors on loess mudstone slope under rainfall conditions

To investigate the stress response characteristics and shear stress transfer mechanism of BFRP(basalt fiber reinforced plastics)anchors under rainfall conditions and to explore the reinforcement effect of BFRP anchors,a comparative indoor physical model test was conducted in this study using loess mudstone slope as a typical case,and multi-attribute response data,such as slope displacement,BFRP anchor strain and axial force,were obtained.Based on the variation law of slope displacement,it can be concluded that the deformation displacement of the slope on the side reinforced by BFRP anchors is smaller than that of slopes reinforced with steel anchors;the bearing capacity of BFRP anchor is given priority in time,and the anchoring effect of BFRP anchor at the top of the slope is given priority,and the axial force value of anchor is characterized by a surface amplification effect in space;the axial force is higher around the anchor head and tends to decay as a negative exponential function as the anchor extends in the direction of the interior of the slope;the shear stress of BFRP anchor and anchorage body are unevenly distributed along the axial direction,with the maximum value occurring in the free section near the slope surface and decreases as the BFRP anchor extends towards the interior of the slope.These results can provide a theoretical basis for the optimal design of BFRP anchors.

Dynamic response characteristics of a circular lined tunnel under anisotropy frost heave of overlying soil at the tunnel portal section in cold regions

The rapid development of traffic engineering in cold regions and its consequent problems need to be considered.In this paper,the dynamic response characteristics of the tunnel portal section in cold regions with harmonic load acting on the lining were studied in the frequency domain.The lining is in close contact with the frozen soil,and there is relative movement between the frozen and unfrozen soil due to the phase change.The analytical solution of the vibration of tunnel portal section caused by the harmonic load acting on the lining was derived under the consideration of the anisotropy frost heave of overlying soil.Based on the continuity conditions and boundary conditions,the undetermined coefficients were obtained,and the analytical solutions for different medium displacements and stresses of the cold-region tunnel system were acquired.The vertical pressure coefficient was equivalently simplified as a variable that could be used to replace the thickness of the overlying soil above the tunnel.The analysis of the parameter model shows that the change of the medium parameters(lining,frozen,and unfrozen soil)affects the circumferential stresses,the radial displacements and their peak frequencies of the soil.For example,the increase of density ratio of tunnel lining to frozen soil decreases the radial stresses of the frozen and unfrozen soil;the increase of volumetric frost heaving strain of the frozen soil increases the radial displacements of the frozen surface and decreases the stability of the frozen surface;the increasing of thickness of the frozen soil significantly reduces the radial displacement of unfrozen soil at dimensionless radius η=4.5 compared with that of frozen soil at η=1.5.

Analysis and application of the response characteristics of DLL and LWD resistivity in horizontal well

There exist different response characteristics in the resistivity measurements of dual laterolog （DLL） and logging while drilling （LWD） electromagnetic wave propagation logging in highly deviated and horizontal wells due to the difference in their measuring principles. In this study, we first use the integral equation method simulated the response characteristics of LWD resistivity and use the three dimensional finite element method （3D-FEM） simulated the response characteristics of DLL resistivity in horizontal wells, and then analyzed the response differences between the DLL and LWD resistivity. The comparative analysis indicated that the response differences may be caused by different factors such as differences in the angle of instrument inclination, anisotropy, formation interface, and mud intrusion. In the interface, the curves of the LWD resistivity become sharp with increases in the deviation while those of the DLL resistivity gradually become smooth. Both curves are affected by the anisotropy although the effect on DLL resistivity is lower than the LWD resistivity. These differences aid in providing a reasonable explanation in the horizontal well. However, this can also simultaneously lead to false results. At the end of the study, we explain the effects of the differences in the interpretation of the horizontal well based on the results and actual data analysis.

High-power microwaves response characteristics of silicon and GaAs solar cells

The high-power microwave(HPM)effect heats solar cells,which is an important component of a satellite.This creates a serious reliability problem and affects the normal operation of a satellite.In this paper,the different HPM response characteristics of two kinds of solar cells are comparatively researched by simulation.The results show that there are similarities and differences in hot spot distribution and damage mechanisms between both kinds of solar cell,which are related to the amplitude of HPM.In addition,the duty cycle of repetition frequency contributes more to the temperature accumulation of the solar cells than the carrier frequency.These results will help future research of damage assessment technology,reliability enhancement and the selection of materials for solar cells.

The Seismic Response Characteristics of Polyhalite with Shaded Potash Mine in Central Sichuan

Potash deposition is the result of final phase of brine sedimentary evolution,it’s a limited distribution and easily soluble mineral,it is difficult to find the features on the ground,therefore the prospecting is extremely tough.

THE DYNAMIC PLASTIC RESPONSE CHARACTERISTICS OF CIRCULAR BEAM

In this paper the problem of a circular beam subjected to radial impact by a rigid mass at its lip in its own plane is investigaleil on the basis of rigid-perfectly plastic assumption. The analytical solution of the particle velocities is obtained as the junction of travelling plastic hinge location. Ky analysing the solution, some special properties oj circular beam problem are found.

Research on coupled thermo-hydro-mechanical dynamic response characteristics of saturated porous deep-sea sediments under vibration of mining vehicle

The excessive deformation of deep-sea sediments caused by the vibration of the mining machine will adversely affect the efficiency and safety of mining.Combined with the deep-sea environment,the coupled thermo-hydro-mechanical problem for saturated porous deep-sea sediments subject to the vibration of the mining vehicle is investigated.Based on the Green-Lindsay(G-L)generalized thermoelastic theory and Darcy’s law,the model of thermo-hydro-mechanical dynamic responses for saturated porous deep-sea sediments under the vibration of the mining vehicle is established.We obtain the analytical solutions of non-dimensional vertical displacement,excess pore water pressure,vertical stress,temperature,and change in the volume fraction field with the normal mode analysis method,and depict them graphically.The normal mode analysis method uses the canonical coordinate transformation to solve the equation,which can quickly decouple the equation by ignoring the modal coupling effect on the basis of the canonical mode.The results indicate that the vibration frequency has obvious influence on the vertical displacement,excess pore water pressure,vertical stress,and change in volume fraction field.The loading amplitude has a great effect on the physical quantities in the foundation,and the changes of the physical quantities increase with the increase in loading amplitude.

Response characteristics of sonar receiver under intense sound pulse

For anti-jamming and anti-countermeasure techniques of the sonar receiver, the response characteristics of the automatic gain control （AGC） circuit and the survivability of the prime circuit under strong interference are analyzed by simulations and experiments. An AGC simulation model based on the voltage control amplifier VCA810 prototype is proposed. Then static and dynamic simulations are realized with single frequency signal and linear frequency modulated （LFM） signal commonly used in the active sonar. Based on intense sound pulse （ISP） interference experiments, the real-time response characteristics of each module of the receiver are studied to verify the correctness of the model as well as the simulation results. Simulation and experiment results show that, under 252 dB/20 μs ISP interference, the specific sonar receiver will produce sustained cut top oscillation above 30 ms, which may affect the receiver and block the regular sonar signal.

Photovoltaic Response Characteristics of GaAs Photoconductive Switches Under High Gain Mode

Given is the experiment results in which the laser pulses of 1 046 nm and 532 nm are used to trigger the semi-insulation GaAs photoconductive semiconductor switch(PCSS) with an electrode distance of 4 mm. And made is an analysis of the switchs photovoltaic response characteristics under the high gain mode when the biased field is bigger than the Geng effect field. Also a theory is presented that the main reason for the photovoltaic pulse response delay is the transmission of charge domain, caused by the presence of EL2 energy level in the chip material. Finally, the transmission time of charge domain is calculated and a result that inosculates with the experiment is attained.

Numerical Investigation on Dynamic Response Characteristics of Fluid-Structure Interaction of Gas-Liquid Two-Phase Flow in Horizontal Pipe

Fluid-structure interaction(FSI)of gas-liquid two-phase fow in the horizontal pipe is investigated numerically in the present study.The volume of fluid model and standard k-e turbulence model are integrated to simulate the typical gas-liquid two-phase fow patterns.First,validation of the numerical model is conducted and the typical fow patterns are consistent with the Baker chart.Then,the FSI framework is established to investigate the dynamic responses of the interaction between the horizontal pipe and gas-liquid two-phase fow.The results show that the dynamic response under stratified fow condition is relatively flat and the maximum pipe deformation and equivalent stress are 1.8 mm and 7.5 MPa respectively.Meanwhile,the dynamic responses induced by slug fow,wave fow and annular fow show obvious periodic fuctuations.Furthermore,the dynamic response characteristics under slug flow condition are maximum;the maximum pipe deformation and equivalent stress can reach 4mm and 17.5 MPa,respectively.The principal direction of total deformation is different under various flow patterns.Therefore,the periodic equivalent stress will form the cyclic impact on the pipe wall and affect the fatigue life of the horizontal pipe.The present study may serve as a reference for FSI simulation under gas-liquid two-phase transport conditions.

Research on Dynamic Response Characteristics of 6 MW Spar-Type Floating Offshore Wind Turbine

A 6 MW spar-type floating offshore wind turbine （FOWT） model is put forward and a fully coupled aero-hydro-servo-elastic time domain model is established in the fatigue, aerodynamics, structures and turbulence （FAST） code. Influence rules of wind 10ad and wave load on the characteristics of 6 MW spar-type FOWT are investigated. Firstly, validation of the model is carried out and a satisfactory result is obtained. The maximal deviations of rotor thrust and power between simulation results and reference values are 4.54% and -2.74%, respectively. Then the characteristics, including rotor thrust, rotor power, out-of-plane blade deflection, tower base fore-aft bending moment, and mooring line tension, are researched. The results illustrate that the mean value of dynamic response characteristics is mainly controlled by the wind-induced action. For characteristics of tower base fore-aft bending moment and platform pitch motion, the oscillation is dominated by the wave-induced action during all conditions considered. For characteristics of out-of-plane blade tip deflection and mooring line tension, the oscillation is commanded by combination effect of wave and wind loads when the wind speed is lower than the rated wind speed （hereinafter referred to as below rated wind speed） and is controlled by the wave-induced action when the wind speed is higher than the rated wind speed （hereinafter referred to as above rated wind speed）. As to the rotor thrust and power, the oscillation is dominated by the wind induced action at below rated wind speed and by the combination action of wind and wave loads at above rated wind speed. The results should be useful to the detailed design and model basin test of the 6 MW spar-type FOWT.

Response characteristics of an ascending auditory neuron AN3 and its projections in the brain of the bushcricket Gampsocleis grationsa

The phonotaxis of bushcrickets demonstrates that they have goodcapability of recognizing conspecific songs and locating the sound source,which bases on complicated auditory mechanisms of the central nervoussystem(CNS).This article describes the response characteristics of AN3,an auditory ascending neuron in the prothoracic ganglion,and its projec-tions within the brain.The AN3,with a quasi-tonic discharge pattern,has high sensitivity,directionality and ability to encode sound intensity.Therefore,it plays an important role in auditory information processingof CNS.Its projections in the brain are mainly concentrated in the lateralzone of the deutencephalon,where synaptically connecting local auditoryinterneurons in the brain.

Dynamic model and response characteristics of liquid desiccant air-conditioning system driven by heat pump

The liquid desiccant air-conditioning system is considered as an energy-efficient alternative to the vapor compression system.The dynamic response characteristics of the system under variable cooling load play an important role in the air temperature and humidity control performance of the system.However,the dynamic response characteristics have not been fully revealed in previous studies.Thus,a dynamic model for a heat pump driven liquid desiccant air-conditioning(HPLDAC)system is established to investigate the dynamic response characteristics of the system in this study.Subsequently,experiments were conducted to validate the accuracy of the dynamic model.The simulation results show a good agreement with the experimental data.The simulation results reveal that evaporating water from the solution is a time-consuming process,compared to adding water to the solution.It spends a long time for the HPLDAC system to decrease the high relative humidity of supply air to a low value,which limits the air temperature and humidity control performance of the system.The upper band for the water replenishing value opening(△φup)is a crucial parameter to improve the limitation.When△φup decreases from 1.0%产to 0.25%,the time consumed to reduce the supply air relative humidity to the new lower set value can be saved by 30.6%.

Circuit-Level Analysis on Opto-Electronic Characteristics of Ferroelectric Liquid Crystal

We propose an electronic model in Spice, instead of traditional mathematical analysis, for analyzing the performance of ferroelectric liquid crystal （FLC） under various working conditions. Using this equivalent circuit model,it is easy to simulate and analyze the behavior of an FLC layer in three different typical parameters,including temperature, input light wavelength, and the frequency of driving voltage. We conclude that the response velocity drops as the wavelength increases in the range of visible light, and for the parameter of temperature, the velocity reaches its lowest value when the temperature reaches a certain degree,meanwhile,the frequency of driving voltage exerts important effects on the response velocity only when the frequency is beyond a critical value. Excellent agreement is achieved between simulation and experimental results.

Combined Wind-Storage Frequency Modulation Control Strategy Based on Fuzzy Prediction and Dynamic Control

To ensure frequency stability in power systems with high wind penetration,the doubly-fed induction generator(DFIG)is often used with the frequency fast response control(FFRC)to participate in frequency response.However,a certain output power suppression amount(OPSA)is generated during frequency support,resulting in the frequency modulation(FM)capability of DFIG not being fully utilised,and the system’s unbalanced power will be increased during speed recovery,resulting in a second frequency drop(SFD)in the system.Firstly,the frequency response characteristics of the power system with DFIG containing FFRC are analysed.Then,based on the analysis of the generation mechanism of OPSA and SFD,a combined wind-storage FM control strategy is proposed to improve the system’s frequency response characteristics.This strategy reduces the effect of OPSA and improves the FM capability of DFIG by designing the fuzzy logic of the coefficients of FFRC according to the system frequency index in the frequency support stage.During the speed recovery stage,the energy storage(ES)active power reference value is calculated according to the change of DFIG rotor speed,and the ES output power is dynamically adjusted to reduce the SFD.Finally,taking the IEEE 39-bus test system as an example,real-time digital simulation verification was conducted based on the RTLAB OP5707 simulation platform.The simulation results showthat theproposedmethodcan improve theFMcapabilityofDFIG,reduce the SFDunder thepremise of guaranteeing the rapid rotor speed recovery,and avoid the overshooting phenomenon so that the systemfrequency can be quickly restored to a stable state.

Temporal and spatial response of vegetation NDVI to temperature and precipitation in eastern China

Temporal and spatial response characteristics of vegetation NDVI to the variation of temperature and precipitation in the whole year, spring, summer and autumn was analyzed from April 1998 to March 2008 based on the SPOT VGT-NDVI data and daily temperature and precipitation data from 205 meteorological stations in eastern China. The results indicate that as a whole, the response of vegetation NDVI to the variation of temperature is more pronounced than that of precipitation in eastern China. Vegetation NDVI maximally responds to the variation of temperature with a lag of about 10 days, and it maximally responds to the variation of precipitation with a lag of about 30 days. The response of vegetation NDVI to temperature and precipitation is most pronounced in autumn, and has the longest lag in summer. Spatially, the maximum response of vegetation NDVI to the variation of temperature is more pronounced in the northern and middle parts than in the southern part of eastern China. The maximum response of vegetation NDVI to the variation of precipitation is more pronounced in the northern part than in the middle and southern parts of eastern China. The response of vegetation NDVI to the variation of temperature has longer lag in the northern and southern parts than in the middle part of eastern China. The response of vegetation NDVl to the variation of precipitation has the longest lag in the southern part, and the shortest lag in the northern part of eastern China. The response of vegetation NDVI to the variation of temperature and precipitation in eastern China is mainly consistent with other results, but the lag time of vegetation NDVI to the variation of temperature and precipitation has some differences with those results of the monsoon region of eastern China.

Electrical responses and classification of complex waterflooded layers in carbonate reservoirs: A case study of Zananor Oilfield, Kazakhstan

Experiments of electrical responses of waterflooded layers were carried out on porous,fractured,porous-fractured and composite cores taken from carbonate reservoirs in the Zananor Oilfield,Kazakhstan to find out the effects of injected water salinity on electrical responses of carbonate reservoirs.On the basis of the experimental results and the mathematical model of calculating oil-water relative permeability of porous reservoirs by resistivity and the relative permeability model of two-phase flow in fractured reservoirs,the classification standards of water-flooded layers suitable for carbonate reservoirs with complex pore structure were established.The results show that the salinity of injected water is the main factor affecting the resistivity of carbonate reservoir.When low salinity water(fresh water)is injected,the relationship curve between resistivity and water saturation is U-shaped.When high salinity water(salt water)is injected,the curve is L-shaped.The classification criteria of water-flooded layers for carbonate reservoirs are as follows:(1)In porous reservoirs,the water cut(fw)is less than or equal to 5%in oil layers,5%–20%in weak water-flooded layers,20%–50%in moderately water-flooded layers,and greater than 50%in strong water-flooded layers.(2)For fractured,porous-fractured and composite reservoirs,the oil layers,weakly water-flooded layers,moderately water-flooded layers,and severely water-flooded layers have a water content of less than or equal to 5%,5%and 10%,10%to 50%,and larger than 50%respectively.

Biological responses of small yellow croaker(Larimichthys polyactis) to multiple stressors: a case study in the Yellow Sea, China

Temporal changes in biological characteristics of small yellow croaker Larimichthys polyactis in the Yellow Sea were examined for the period of 1960–2008. The body size and age of small yellow croaker decreased substantially, in particular, average length of fish in 2008 was reduced by ~85% than those occurring in 1985, and at that time ~93% of the total catch was dominated by one-year-old individuals. Correspondingly, growth parameters also varied significantly over the years, i.e., k（growth coefficient） and t_0（zero-length age） gradually increased from 0.26 and –0.58 year in 1960 to 0.56 and –0.25 year in 2008, respectively. Although, L∞（body length）sharply decreased from 34.21 cm in 1960 to 24.06 cm in 2008, and t_r（inflexion age） decreased from 3.78 year in1960 to 1.61 year in 2008. There was a great increase both in natural mortality coefficient and fishing mortality coefficient. However, according to the gray correlation analysis, changes in the biological characteristics of small yellow croaker were induced by different stressors ranked as： fishing vessel power〉feeding grade〉sea surface temperature. This study suggests that the active fishery management measures for biological characters of fish populations should be considered.

Dynamic Characteristics and Simplified Numerical Methods of An All-Vertical-Piled Wharf in Offshore Deep Water

There has been a growing trend in the development of offshore deep-water ports in China. For such deep sea projects, all-vertical-piled wharves are suitable structures and generally located in open waters, greatly affected by wave action. Currently, no systematic studies or simplified numerical methods are available for deriving the dynamic characteristics and dynamic responses of all-vertical-piled wharves under wave cyclic loads. In this article, we compare the dynamic characteristics of an all-vertical-piled wharf with those of a traditional inshore high-piled wharf through numerical analysis; our research reveals that the vibration period of an all-vertical-piled wharf under cyclic loading is longer than that of an inshore high-piled wharf and is much closer to the period of the loading wave. Therefore, dynamic calculation and analysis should be conducted when designing and calculating the characteristics of an all-vertical-piled wharf. We establish a dynamic finite element model to examine the dynamic response of an all-vertical-piled wharf under wave cyclic loads and compare the results with those under wave equivalent static load; the comparison indicates that dynamic amplification of the structure is evident when the wave dynamic load effect is taken into account. Furthermore, a simplified dynamic numerical method for calculating the dynamic response of an all-vertical-piled wharf is established based on the P-Y curve. Compared with finite element analysis, the simplified method is more convenient to use and applicable to large structural deformation while considering the soil non-linearity. We confirmed that the simplified method has acceptable accuracy and can be used in engineering applications.