Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on ...Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.展开更多
The rheological behavior and microstructure of semi-solid AZ91D was studied using a Couette type viscometer. The results show that the apparent viscosity of semi-solid AZ91D increases with the cooling rate increasing ...The rheological behavior and microstructure of semi-solid AZ91D was studied using a Couette type viscometer. The results show that the apparent viscosity of semi-solid AZ91D increases with the cooling rate increasing when it is continuously cooled and mechanically stirred and the empiric relation of the apparent viscosity with the cooling rate and solid fraction at shearing rate 93.7 s-1 is expressed as η=[0.66-0.63e(-ε/3.01)]e(fa/0.14), and with the shearing rate and solid fraction at cooling rate 4℃/min is shown as η=0.55e(fa/0.11-γ/87.59), as well as the cooling rate and shearing rate have an important effect on the microstructure of the semi-solid AZ91D alloy slurry, and decreasing the cooling rate and increasing the shearing rate are favorable to the nondendritic evolution of the primary grains.展开更多
The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites w...The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites were dealt with. The viscosity ( h ) and dynamic modulus ( G ) of the composite melts were higher than those of PP matrix, especially those for systems treated with silane, which was attributed to the interfacial adhesion enhancement. However, surface-treatment of mica by titanate resulted in lower h and G, as compared with the treatment by silane. The reason for this is believed to be the formation of the mono-molecular layer on the mica surface.展开更多
Low cement (LC) and ultra low cement (ULC) bauxite SiC castables are important and high performance monolithic refractories and they have been widely used in iron making and incinerator linings. In this work, rheol...Low cement (LC) and ultra low cement (ULC) bauxite SiC castables are important and high performance monolithic refractories and they have been widely used in iron making and incinerator linings. In this work, rheological behavior of LC and ULC bauxite based SiC containing castables has been studied, including the effects of SiC content and cement content on rheological properties of the castables. The results show that with an increase of SiC and cement content, rheological properties of the castables deteriorate. On the other hand, moderate amounts of SiC (4%~8%) and of calcium aluminate cement (2%~4%) have very slight influence on rheological properties, (i.e. when the castables are sheared their torque and yield torque only slightly increase with the shearing speed). The rheological characteristics of the castables follow Bingham fluid and always show shear thinning behavior.展开更多
The effects of milling and active surfactants on the rheological behavior of powder injection molding feedstock were discussed. The feedstock consists of traditional compositional 90W 7Ni 3Fe powder mixture and a wax ...The effects of milling and active surfactants on the rheological behavior of powder injection molding feedstock were discussed. The feedstock consists of traditional compositional 90W 7Ni 3Fe powder mixture and a wax based polymer binder. Before mixing feedstock, the powder mixture was milled for different times in a QM 1 high energy ball mill. The viscosity of the feedstock was examined in a capillary rheometer. The rheological behavior was evaluated from viscosity data. The results show that the feedstock belongs to a pseudoplastic fluid, milling decreases viscosity of the feedstock and the sensitivity of viscosity to shear strain rate. The flowability, rheology and powder loading of this feedstock are improved by milling. Active surfactants such as stearic acid (SA) and di n octyl o phthalate (DOP) have great influences on the rheological properties of the feedstock. DOP improves the flowability and rheological stability of the feedstock further. [展开更多
The rheological behavior of a low epoxy resin system-SR8100/SD8734 for RTM in aviation industry was studied with viscosity experiments. The dual-Arrhenius rheological model and the improved engineering viscosity model...The rheological behavior of a low epoxy resin system-SR8100/SD8734 for RTM in aviation industry was studied with viscosity experiments. The dual-Arrhenius rheological model and the improved engineering viscosity model were introduced and compared with the experimental data. The results indicated that the viscosity in the earlier stage calculated by dual-Arrhenius model matched the experimental data. As rising to 400 m.Pas, the viscosity calculated by the improved engineering model was closer to the experimental data. The processing windows of the resin system for RTM were determined by combining the two models, which could predict the theological behavior of the resin system in a more credible way. 30-45 ℃ was the optimum processing temperature.展开更多
Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of h...Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of heterogeneous titanium-bearing molten slag. By measuring the relationships among the viscosity, the shear stress and the shear rate of molten slags with different Ti C contents at different temperatures, the rheological constitutive equations were established along with the rheological parameters; in addition, the non-Newtonian fluid types of the molten slags were determined. The results indicated that, with increasing Ti C content, the viscosity of the molten slag tended to increase. If the Ti C content was less than 2wt%, the molten slag exhibited the Newtonian fluid behavior when the temperature was higher than the critical viscosity temperature of the molten slag. In contrast, the molten slag exhibited the non-Newtonian pseudoplastic fluid characteristic and the shear thinning behavior when the temperature was less than the critical viscosity temperature. However, if the Ti C content exceeded 4wt%, the molten slag produced the yield stress and exhibited the Bingham and plastic pseudoplastic fluid behaviors when the temperature was higher and lower than the critical viscosity temperature, respectively. When the Ti C content increased further, the yield stress of the molten slag increased and the shear thinning phenomenon became more obvious.展开更多
The chemorheological behaviors of a low viscosity epoxy resin system (Huntsman 1564/3486) for vacuum infusion moulding process (VIMP) were studied with viscosity experiments.The dual-Arrhenius rheological model an...The chemorheological behaviors of a low viscosity epoxy resin system (Huntsman 1564/3486) for vacuum infusion moulding process (VIMP) were studied with viscosity experiments.The dual-Arrhenius rheological model and the engineering viscosity model were established and compared with the experimental data.The result showed that the viscosity in the earlier stage calculated by dual-Arrhenius model were smaller than the experimental data,while the data calculated by the engineering model were larger.Combining the two models together can predict the rheological behaviors of the resin system in a more credible manner.The processing windows of the resin system for VIMP were determined based on the two models.The optimum processing temperature is 30-45 ℃.展开更多
Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) ...Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) over dot), psi (10)((gamma) over dot) and shear rate ((gamma) over dot), and topologically constrained dimension number n ' and a were derived. Linear viscoelastic parameters (eta (0) and G(N)(0)) and topologically constrained dimension number (n ' a and <(<upsilon>)over bar>) as a function of the primary molecular weight (M-n), molecular weight between entanglements (M-C) and the entanglement sites sequence distribution in polymer chain were determined. A new method for determination of viscoelastic parameters (eta (0), psi (10), G(N)(0) and J(e)(0)), topologically constrained dimension number (n ', a and v) and molecular weight (M-n, M-c and M-e) from the shear flow measurements was proposed. It was used to determine those parameters and structures of HDPE, making a good agreement between these values and those obtained by other methods. The agreement affords a quantitative verification for the molecular theory of nonlinear viscoelasticity with constrained entanglement in polymer melts.展开更多
Blends of polyphenylene sulfide (PPS) containing trace amounts of branching and/or cross-linking in chain and Polyamide-66 (PA-66) have been prepared by melt blending. The rheological behavior of PPS/PA-66 blends has ...Blends of polyphenylene sulfide (PPS) containing trace amounts of branching and/or cross-linking in chain and Polyamide-66 (PA-66) have been prepared by melt blending. The rheological behavior of PPS/PA-66 blends has been studied by means of capillary rheometer, and compared with PPS. The effects of shear rate, shear stress and temperature on the how of PPS/PA-66 blends and PPS are discussed. The non-Newtonian indexes and the activation energies of viscous how are obtained. The results show that the apparent viscosity of PPS/PA-66 blends is not sensitive to shear rate and stress, but decreases with the elevation of temperature. On the contrary, the apparent viscosity of the PPS decreases obviously with the increasing of shear rate and shear stress, but it is increased by the elevation of temperature.展开更多
This paper deals with a peculiar rheological behavior of aluminum at near-solidus temperatures. It has been experimentally estab- lished that there is an inverse strain rate dependence of strain resistance at temperat...This paper deals with a peculiar rheological behavior of aluminum at near-solidus temperatures. It has been experimentally estab- lished that there is an inverse strain rate dependence of strain resistance at temperatures ranging between 560 and 640℃ and strain rates ranging from 0.06 to 1.2 s-1. Electron backscatter diffraction analysis has shown that at temperatures ranging between 540 and 640℃ and strain rates ranging from 0.06 to 0.1 s-1, the main process of softening is dynamic polygonization, resulting in in situ recrystallization. At higher strain rates, ranging between 0.8 and 1.2 s-1, and temperatures ranging between 560 and 640℃, the recovery is dynamic. This unusual behavior of the mechanism of softening and the presence of the inverse strain rate dependence of strain resistance can be explained by blocking the motion of free dislocations by foreign atoms, which occurs at strain rates ranging between 0.06 and 0.1 s-1 This process results in dislocation pile-up, thereby causing in sire recrystallization. At strain rates exceeding 0.16 s-1, there is no intensive blocking of dislocations, leading to a direct strain rate dependence of strain resistance.展开更多
The viscoelastic properties of melts of nanocomposites with partially exfoliated structures, which were composed of low-density polyethylene (LDPE), ethylene vinyl acetate copolymer (EVA), and montmofillonite and ...The viscoelastic properties of melts of nanocomposites with partially exfoliated structures, which were composed of low-density polyethylene (LDPE), ethylene vinyl acetate copolymer (EVA), and montmofillonite and modified by cetyltrimethyl ammonium bromide and octadecyltrimethyl ammonium bromide, were studied. The results obtained through measurements of the dynamic storage modulus G′, the dynamic loss modulus G″, and the transiem stress relaxation modulus G(t) of the composites, reveal that the viscoelastic properties of the composites strongly depend on the amount of montmorillonite that is exfoliated into the composites. With the increase in montmoriUonite content, the composites show an obvious property of pseudo solid-like materials within the region of lower frequencies (ω). The montmorillonite layers are aligned along the stress direction, and the dependence of dynamic modulus on ω, appears quite different for the composites before and after being exposed to a large amplitude oscillatory shears.展开更多
Poly(vinyl alcohol)/collagen (PVA/COL) micro-nanofibers were successfully prepared by electrospinning process. Water, green, and non-toxic was used as the solvent. The electrospun mats consisted of micro-nanoscale...Poly(vinyl alcohol)/collagen (PVA/COL) micro-nanofibers were successfully prepared by electrospinning process. Water, green, and non-toxic was used as the solvent. The electrospun mats consisted of micro-nanoscale fibers with mean diameter ranging from approximately 363 nm to 179 nm. It was observed that the mean diameters of PVA/COL electrospun fibers decreased with increasing collagen content. The effects of PVA/COL blending ratio on the rheological behavior of PVA/COL blended solutions were investigated by rotate rheometer. It was found that PVA/COL blended solutions behaved as Non-Newtonian fluids. With increasing collagen content, the Non-Newtonian index (n) of PVA/COL blended solutions decreased. Meanwhile, a linear relationship was found between the Non-Newtonian index (n) and the mean diameters of the PVA/COL micro- nanofibers. The chemical structures of PVA/COL electrospun fibers were also characterized by FTIR.展开更多
The apparent kinetics and cure behavior of novel interpenetrating polymer networks(IPNs) based on cycloaliphatic epoxy resin(CER) and tri-functional acrylate have been investigated by means of differential scanning ca...The apparent kinetics and cure behavior of novel interpenetrating polymer networks(IPNs) based on cycloaliphatic epoxy resin(CER) and tri-functional acrylate have been investigated by means of differential scanning calorimetry(DSC) and Fourier transform infrared spectroscopy(FT-IR).The results of DSC measurements show that the curing reaction of the TMPTMA component is much earlier than that of the CER component,which can lead to the formation of the IPNs.In contrast to neat anhydride-CER system,the anhydri...展开更多
In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the ...In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the apparent viscosity and microstructure were investigated. The results showed that adding Ti B2 is effective for optimizing primary α-Al, but compared with the 4.5wt.%Ti B2/7075 composite, the addition of 9wt.%Ti B2 had no further significant refinement role in the 9wt.%Ti B2/7075 composite due to particle aggregation. The viscosities of semi-solid 7075 alloy and Ti B2/7075 composite slurries increased with an increase in solid fraction, but decreased with an increase in shear rate. The viscosity of 4.5wt.% Ti B2/7075 was the lowest among the three samples, and that of 7075 alloy was the highest under the same conditions. The primary α-Al grain size was decreased, and the dendritic grains grew into spherical shapes after shearing. Based on the experimental results, viscosity models of the semi-solid 7075 alloy and 4.5wt.% and 9wt.%Ti B2/7075 composites were formulated. According to the simulation results, the shrinkage porosity of the 4.5wt.%Ti B2/7075 wheel was lower than those of the 7075 alloy and 9wt.%Ti B2/7075 wheels.展开更多
Erwinia (E) gum, an extracellular polysaccharide, is composed of fucose, galatose, glucose and glucuronic acid. Its viscosity behavior was investigated by a low-shear-rate multiball viscometer and a rotational viscome...Erwinia (E) gum, an extracellular polysaccharide, is composed of fucose, galatose, glucose and glucuronic acid. Its viscosity behavior was investigated by a low-shear-rate multiball viscometer and a rotational viscometer. Its weight-average molecular weight M-w and intrinsic viscosity [eta] in 0.2 mol/L NaCl aqueous solution were measured by light scattering method at 35 degrees C and viscometry at 25 degrees C and found to be 1.06 x 10(6) g/mol and 1050 mL/g, respectively, and its aggregates in aqueous solution were proved by gel permeation chromatography (GPC). These results indicated that E gum in water has exceedingly high viscosity and exhibits Binham fluid behavior, owing to its aggregation. The viscosity of E gum decreased with increasing temperature, and the turning point appeared at 38 degrees C for dilute solution and 80 degrees C for concentrated solution suggesting that the aggregates of E gum in water started to disaggregate under these temperatures. In addition, the aggregates can be disrupted by adding either acid or base. The experimental results indicated that the E gum is a good thickening agent, and its fluid behavior is similar to xanthan.展开更多
By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedu...By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedures was established, by which the dynamic rheological parameters of polymer can be acquired, and a set of data management methods to undergo time-domain or frequency-domain analysis was set up for dynamic rheological data of polymer melt. Meantime, the characterization formula of polymer melt's rheological behavior in a vibrating force field was set up. The instantaneous value of capillary entry pressure, capillary volume flow rate and their phase difference were measured and analyzed, and the melt apparent viscosity, which describes the rheological behavior of polymer melt in a vibrating force field, was obtained.展开更多
The waterborne dispersions of epoxy resin were prepared by the phase inversion emulsification technique. Rheological behavior and its relationship with the structural change of the systems were studied. It was shown t...The waterborne dispersions of epoxy resin were prepared by the phase inversion emulsification technique. Rheological behavior and its relationship with the structural change of the systems were studied. It was shown that the concentrated dispersions were highly viscoelastic and pseudoplastic, which was attributed to the formation of a physical network among the waterborne particles via hydrogen bond. The dilute dispersions were Newtonian fluids. The discrete clusters composed of small waterborne particles were found in diluted dispersions. With increasing solid content, there existed a structural transition via percolation through a cluster-cluster aggregation mode to form the physical network, which was qualitatively evidenced by the TEM morphologies.展开更多
Study on rheological properties of gunned refractory is an effective way to optimize the quality of repaired layer and gunning operation. The fluidity of refractory was quantitatively evaluated as well as the rheologi...Study on rheological properties of gunned refractory is an effective way to optimize the quality of repaired layer and gunning operation. The fluidity of refractory was quantitatively evaluated as well as the rheological behavior of refractory particle-water suspensions. The relationship between the fluidity of refractory particle-water suspension and that of gunned refractory, and the relationship between the fluidity and adhesion ability of gunned refractory were studied. The experiments were carried out with a special rheometer and gunning machine. The results show that there is strong influence of some parameters on the rheological behavior of gunned refractory and gunning process. Interactions between particles and water that lead to the formation of gelatinous structures in this suspension are discussed.展开更多
For the concentrated dispersions of epoxy resin prepared by phase inversion emulsification technique, the effects of solid content and temperature on the rheological behavior are studied. It is found that there exists...For the concentrated dispersions of epoxy resin prepared by phase inversion emulsification technique, the effects of solid content and temperature on the rheological behavior are studied. It is found that there exists reversible structural transition in concentrated dispersions subjected to shearing. The viscosity oscillation correlated with high viscoelasticity at lower stress is remarkable in highly concentrated dispersions. There exists storage modules overshot at higher stress during the dynamic stress time ramp test. This could provide some information on dynamics of structure changes during shear action. Besides, the effects of solid content and temperature on the relationship between tangent delta and frequency are essentially different.展开更多
基金This work was supported by the National Science Fund for Distinguished Young Scholars of China (No.50125312) andSpecial Funds for Major State Basic Research Projects (No.G1999064800).
文摘Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
基金The research was supported by the National“973”Project Foundation of China(No.G2000067202)the National“863”Plan of China(No.G2002AA336080).
文摘The rheological behavior and microstructure of semi-solid AZ91D was studied using a Couette type viscometer. The results show that the apparent viscosity of semi-solid AZ91D increases with the cooling rate increasing when it is continuously cooled and mechanically stirred and the empiric relation of the apparent viscosity with the cooling rate and solid fraction at shearing rate 93.7 s-1 is expressed as η=[0.66-0.63e(-ε/3.01)]e(fa/0.14), and with the shearing rate and solid fraction at cooling rate 4℃/min is shown as η=0.55e(fa/0.11-γ/87.59), as well as the cooling rate and shearing rate have an important effect on the microstructure of the semi-solid AZ91D alloy slurry, and decreasing the cooling rate and increasing the shearing rate are favorable to the nondendritic evolution of the primary grains.
文摘The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites were dealt with. The viscosity ( h ) and dynamic modulus ( G ) of the composite melts were higher than those of PP matrix, especially those for systems treated with silane, which was attributed to the interfacial adhesion enhancement. However, surface-treatment of mica by titanate resulted in lower h and G, as compared with the treatment by silane. The reason for this is believed to be the formation of the mono-molecular layer on the mica surface.
文摘Low cement (LC) and ultra low cement (ULC) bauxite SiC castables are important and high performance monolithic refractories and they have been widely used in iron making and incinerator linings. In this work, rheological behavior of LC and ULC bauxite based SiC containing castables has been studied, including the effects of SiC content and cement content on rheological properties of the castables. The results show that with an increase of SiC and cement content, rheological properties of the castables deteriorate. On the other hand, moderate amounts of SiC (4%~8%) and of calcium aluminate cement (2%~4%) have very slight influence on rheological properties, (i.e. when the castables are sheared their torque and yield torque only slightly increase with the shearing speed). The rheological characteristics of the castables follow Bingham fluid and always show shear thinning behavior.
文摘The effects of milling and active surfactants on the rheological behavior of powder injection molding feedstock were discussed. The feedstock consists of traditional compositional 90W 7Ni 3Fe powder mixture and a wax based polymer binder. Before mixing feedstock, the powder mixture was milled for different times in a QM 1 high energy ball mill. The viscosity of the feedstock was examined in a capillary rheometer. The rheological behavior was evaluated from viscosity data. The results show that the feedstock belongs to a pseudoplastic fluid, milling decreases viscosity of the feedstock and the sensitivity of viscosity to shear strain rate. The flowability, rheology and powder loading of this feedstock are improved by milling. Active surfactants such as stearic acid (SA) and di n octyl o phthalate (DOP) have great influences on the rheological properties of the feedstock. DOP improves the flowability and rheological stability of the feedstock further. [
基金Funded by the Freedom Explore Program of Central South University(No.721500254)the Hunan Provincial Innovation Foundation for Postgraduate(No.CX2012B052)
文摘The rheological behavior of a low epoxy resin system-SR8100/SD8734 for RTM in aviation industry was studied with viscosity experiments. The dual-Arrhenius rheological model and the improved engineering viscosity model were introduced and compared with the experimental data. The results indicated that the viscosity in the earlier stage calculated by dual-Arrhenius model matched the experimental data. As rising to 400 m.Pas, the viscosity calculated by the improved engineering model was closer to the experimental data. The processing windows of the resin system for RTM were determined by combining the two models, which could predict the theological behavior of the resin system in a more credible way. 30-45 ℃ was the optimum processing temperature.
基金financially supported by the National Science Foundation of China (Nos. 51090383 and 51174051)
文摘Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of heterogeneous titanium-bearing molten slag. By measuring the relationships among the viscosity, the shear stress and the shear rate of molten slags with different Ti C contents at different temperatures, the rheological constitutive equations were established along with the rheological parameters; in addition, the non-Newtonian fluid types of the molten slags were determined. The results indicated that, with increasing Ti C content, the viscosity of the molten slag tended to increase. If the Ti C content was less than 2wt%, the molten slag exhibited the Newtonian fluid behavior when the temperature was higher than the critical viscosity temperature of the molten slag. In contrast, the molten slag exhibited the non-Newtonian pseudoplastic fluid characteristic and the shear thinning behavior when the temperature was less than the critical viscosity temperature. However, if the Ti C content exceeded 4wt%, the molten slag produced the yield stress and exhibited the Bingham and plastic pseudoplastic fluid behaviors when the temperature was higher and lower than the critical viscosity temperature, respectively. When the Ti C content increased further, the yield stress of the molten slag increased and the shear thinning phenomenon became more obvious.
基金Supported by the 863 National Project of China (No.2007AA03Z563)the Specialized Project of the HUNAN Province of China(No.2006GK1002)
文摘The chemorheological behaviors of a low viscosity epoxy resin system (Huntsman 1564/3486) for vacuum infusion moulding process (VIMP) were studied with viscosity experiments.The dual-Arrhenius rheological model and the engineering viscosity model were established and compared with the experimental data.The result showed that the viscosity in the earlier stage calculated by dual-Arrhenius model were smaller than the experimental data,while the data calculated by the engineering model were larger.Combining the two models together can predict the rheological behaviors of the resin system in a more credible manner.The processing windows of the resin system for VIMP were determined based on the two models.The optimum processing temperature is 30-45 ℃.
基金The authors gratefully a.cknowledge financial supportfrom th6 Natiol-al Natural Science Foundatiol- of CI-h-a. The number of
文摘Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) over dot), psi (10)((gamma) over dot) and shear rate ((gamma) over dot), and topologically constrained dimension number n ' and a were derived. Linear viscoelastic parameters (eta (0) and G(N)(0)) and topologically constrained dimension number (n ' a and <(<upsilon>)over bar>) as a function of the primary molecular weight (M-n), molecular weight between entanglements (M-C) and the entanglement sites sequence distribution in polymer chain were determined. A new method for determination of viscoelastic parameters (eta (0), psi (10), G(N)(0) and J(e)(0)), topologically constrained dimension number (n ', a and v) and molecular weight (M-n, M-c and M-e) from the shear flow measurements was proposed. It was used to determine those parameters and structures of HDPE, making a good agreement between these values and those obtained by other methods. The agreement affords a quantitative verification for the molecular theory of nonlinear viscoelasticity with constrained entanglement in polymer melts.
基金This work was supported by the National High Technology Program Fund(863)of China.
文摘Blends of polyphenylene sulfide (PPS) containing trace amounts of branching and/or cross-linking in chain and Polyamide-66 (PA-66) have been prepared by melt blending. The rheological behavior of PPS/PA-66 blends has been studied by means of capillary rheometer, and compared with PPS. The effects of shear rate, shear stress and temperature on the how of PPS/PA-66 blends and PPS are discussed. The non-Newtonian indexes and the activation energies of viscous how are obtained. The results show that the apparent viscosity of PPS/PA-66 blends is not sensitive to shear rate and stress, but decreases with the elevation of temperature. On the contrary, the apparent viscosity of the PPS decreases obviously with the increasing of shear rate and shear stress, but it is increased by the elevation of temperature.
基金financially supported by Russian Science Foundation(No. 14-19-01358)
文摘This paper deals with a peculiar rheological behavior of aluminum at near-solidus temperatures. It has been experimentally estab- lished that there is an inverse strain rate dependence of strain resistance at temperatures ranging between 560 and 640℃ and strain rates ranging from 0.06 to 1.2 s-1. Electron backscatter diffraction analysis has shown that at temperatures ranging between 540 and 640℃ and strain rates ranging from 0.06 to 0.1 s-1, the main process of softening is dynamic polygonization, resulting in in situ recrystallization. At higher strain rates, ranging between 0.8 and 1.2 s-1, and temperatures ranging between 560 and 640℃, the recovery is dynamic. This unusual behavior of the mechanism of softening and the presence of the inverse strain rate dependence of strain resistance can be explained by blocking the motion of free dislocations by foreign atoms, which occurs at strain rates ranging between 0.06 and 0.1 s-1 This process results in dislocation pile-up, thereby causing in sire recrystallization. At strain rates exceeding 0.16 s-1, there is no intensive blocking of dislocations, leading to a direct strain rate dependence of strain resistance.
基金Supported by National Natural Science Foundation of China (No. 50373037) and the Special Funds for Major State Basic Re-search Projects (No. 2005CB623802).
文摘The viscoelastic properties of melts of nanocomposites with partially exfoliated structures, which were composed of low-density polyethylene (LDPE), ethylene vinyl acetate copolymer (EVA), and montmofillonite and modified by cetyltrimethyl ammonium bromide and octadecyltrimethyl ammonium bromide, were studied. The results obtained through measurements of the dynamic storage modulus G′, the dynamic loss modulus G″, and the transiem stress relaxation modulus G(t) of the composites, reveal that the viscoelastic properties of the composites strongly depend on the amount of montmorillonite that is exfoliated into the composites. With the increase in montmoriUonite content, the composites show an obvious property of pseudo solid-like materials within the region of lower frequencies (ω). The montmorillonite layers are aligned along the stress direction, and the dependence of dynamic modulus on ω, appears quite different for the composites before and after being exposed to a large amplitude oscillatory shears.
基金Funded by the National Natural Science Foundation of China(Nos.21076199,51373158)the Department of Science and Technology of Henan Province(No.124300510)
文摘Poly(vinyl alcohol)/collagen (PVA/COL) micro-nanofibers were successfully prepared by electrospinning process. Water, green, and non-toxic was used as the solvent. The electrospun mats consisted of micro-nanoscale fibers with mean diameter ranging from approximately 363 nm to 179 nm. It was observed that the mean diameters of PVA/COL electrospun fibers decreased with increasing collagen content. The effects of PVA/COL blending ratio on the rheological behavior of PVA/COL blended solutions were investigated by rotate rheometer. It was found that PVA/COL blended solutions behaved as Non-Newtonian fluids. With increasing collagen content, the Non-Newtonian index (n) of PVA/COL blended solutions decreased. Meanwhile, a linear relationship was found between the Non-Newtonian index (n) and the mean diameters of the PVA/COL micro- nanofibers. The chemical structures of PVA/COL electrospun fibers were also characterized by FTIR.
基金supported by Shanghai Committee of Science Technology for Major Research Project of ShanghaiCity(No.05dz22303).
文摘The apparent kinetics and cure behavior of novel interpenetrating polymer networks(IPNs) based on cycloaliphatic epoxy resin(CER) and tri-functional acrylate have been investigated by means of differential scanning calorimetry(DSC) and Fourier transform infrared spectroscopy(FT-IR).The results of DSC measurements show that the curing reaction of the TMPTMA component is much earlier than that of the CER component,which can lead to the formation of the IPNs.In contrast to neat anhydride-CER system,the anhydri...
文摘In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the apparent viscosity and microstructure were investigated. The results showed that adding Ti B2 is effective for optimizing primary α-Al, but compared with the 4.5wt.%Ti B2/7075 composite, the addition of 9wt.%Ti B2 had no further significant refinement role in the 9wt.%Ti B2/7075 composite due to particle aggregation. The viscosities of semi-solid 7075 alloy and Ti B2/7075 composite slurries increased with an increase in solid fraction, but decreased with an increase in shear rate. The viscosity of 4.5wt.% Ti B2/7075 was the lowest among the three samples, and that of 7075 alloy was the highest under the same conditions. The primary α-Al grain size was decreased, and the dendritic grains grew into spherical shapes after shearing. Based on the experimental results, viscosity models of the semi-solid 7075 alloy and 4.5wt.% and 9wt.%Ti B2/7075 composites were formulated. According to the simulation results, the shrinkage porosity of the 4.5wt.%Ti B2/7075 wheel was lower than those of the 7075 alloy and 9wt.%Ti B2/7075 wheels.
基金This work was financially supported by Asahi Chemical Industry Co., Ltd. of Japan and National Natural Science Foundation of China (No. 29374170).
文摘Erwinia (E) gum, an extracellular polysaccharide, is composed of fucose, galatose, glucose and glucuronic acid. Its viscosity behavior was investigated by a low-shear-rate multiball viscometer and a rotational viscometer. Its weight-average molecular weight M-w and intrinsic viscosity [eta] in 0.2 mol/L NaCl aqueous solution were measured by light scattering method at 35 degrees C and viscometry at 25 degrees C and found to be 1.06 x 10(6) g/mol and 1050 mL/g, respectively, and its aggregates in aqueous solution were proved by gel permeation chromatography (GPC). These results indicated that E gum in water has exceedingly high viscosity and exhibits Binham fluid behavior, owing to its aggregation. The viscosity of E gum decreased with increasing temperature, and the turning point appeared at 38 degrees C for dilute solution and 80 degrees C for concentrated solution suggesting that the aggregates of E gum in water started to disaggregate under these temperatures. In addition, the aggregates can be disrupted by adding either acid or base. The experimental results indicated that the E gum is a good thickening agent, and its fluid behavior is similar to xanthan.
文摘By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedures was established, by which the dynamic rheological parameters of polymer can be acquired, and a set of data management methods to undergo time-domain or frequency-domain analysis was set up for dynamic rheological data of polymer melt. Meantime, the characterization formula of polymer melt's rheological behavior in a vibrating force field was set up. The instantaneous value of capillary entry pressure, capillary volume flow rate and their phase difference were measured and analyzed, and the melt apparent viscosity, which describes the rheological behavior of polymer melt in a vibrating force field, was obtained.
基金This work was supported by the National Natural Science Foundation of China (Grant No. 29774038), and 973 project "Fundamental study on enhanced oil recovery" of the Ministry of China Science and Technology.
文摘The waterborne dispersions of epoxy resin were prepared by the phase inversion emulsification technique. Rheological behavior and its relationship with the structural change of the systems were studied. It was shown that the concentrated dispersions were highly viscoelastic and pseudoplastic, which was attributed to the formation of a physical network among the waterborne particles via hydrogen bond. The dilute dispersions were Newtonian fluids. The discrete clusters composed of small waterborne particles were found in diluted dispersions. With increasing solid content, there existed a structural transition via percolation through a cluster-cluster aggregation mode to form the physical network, which was qualitatively evidenced by the TEM morphologies.
基金ItemSponsored by National Natural Science Foundation of China (50174026) Provincial Natural Science Foundation ofAnhui of China (03044704)
文摘Study on rheological properties of gunned refractory is an effective way to optimize the quality of repaired layer and gunning operation. The fluidity of refractory was quantitatively evaluated as well as the rheological behavior of refractory particle-water suspensions. The relationship between the fluidity of refractory particle-water suspension and that of gunned refractory, and the relationship between the fluidity and adhesion ability of gunned refractory were studied. The experiments were carried out with a special rheometer and gunning machine. The results show that there is strong influence of some parameters on the rheological behavior of gunned refractory and gunning process. Interactions between particles and water that lead to the formation of gelatinous structures in this suspension are discussed.
文摘For the concentrated dispersions of epoxy resin prepared by phase inversion emulsification technique, the effects of solid content and temperature on the rheological behavior are studied. It is found that there exists reversible structural transition in concentrated dispersions subjected to shearing. The viscosity oscillation correlated with high viscoelasticity at lower stress is remarkable in highly concentrated dispersions. There exists storage modules overshot at higher stress during the dynamic stress time ramp test. This could provide some information on dynamics of structure changes during shear action. Besides, the effects of solid content and temperature on the relationship between tangent delta and frequency are essentially different.