On Distributed Concurrent Multi-Port Router Test System

This paper presents a framework of the distributed concurrent multi-port-testing test system (CMPT-TS) for IP routers under development at Sichuan Network Communication Key Laboratory. Having analyzed the actuality of concurrent testing for routers, this paper develops a distributed architecture of CMPT-TS and discusses its functional components in detail. Moreover, a new test definition language, CMPT definition language, is also introduced simply.

Room-temperature test system for 162.5 MHz high-power couplers

Fundamental power couplers are crucial components for feeding radio frequency power to accelerating cavities. Couplers must be tested and conditioned on a room-temperature test stand to evaluate and potentially improve their performance before being installed in an accelerating cavity. A new test system has been designed and is under construction at the institute of modern physics.For this test system, multiple conditioning modes, including the pulse mode, CW mode, and amplitude-sweeping mode, have been embedded in the low-level radio frequency system of the test stand. All of these conditioning modes can be run manually or automatically. In addition, a novel test cavity is proposed and has been designed, which facilitates non-contact conditioning and a multi-purpose test stand.

Design and Experimental Investigation for Subsea Control Module Test System

As a core part of subsea production systems,subsea control modules(SCMs)are costly,difficult,and expensive to install and inconvenient to use in underwater maintenance.Therefore,performance and function tests must be carried out before launching SCMs.This study developed a testing device and an SCM test by investigating SCMs and their underwater.The testing device includes four parts:a hydraulic station,an SCM test stand,a signal generating device,and an electronic test unit.First,the basic indices of the testing device were determined from the performance and working parameters of the SCM.Second,the design scheme of the testing device for the SCM was tentatively proposed,and each testing device was designed.Finally,a practical measurement of the SCM,in combination with the hydraulic station,SCM test stand,signal generator,electronic unit,and highpressure water tank,was carried out according to the test requirements.The measurement mainly involved equipment inspection before testing and an experimental test for the SCM.The validity and feasibility of the testing device and method were simultaneously verified through an association test.

Flexible substructure online hybrid test system using conventional testing devices

This paper presents a substructure online hybrid test system that is extensible for geographically distributed tests. This system consists of a set of devices conventionally used for cyclic tests to load the tested substructures onto the target displacement or the target force. Due to their robustness and portability, individual sets of conventional loading devices can be transported and reconfigured to realize physical loading in geographically remote laboratories. Another appealing feature is the flexible displacement-force mixed control that is particularly suitable for specimens having large disparities in stiffness during various performance stages. To conduct a substructure online hybrid test, an extensible framework is developed, which is equipped with a generalized interface to encapsulate each substructure. Multiple tested substructures and analyzed substructures using various structural program codes can be accommodated within the single framework, simply interfaced with the boundary displacements and forces. A coordinator program is developed to keep the boundaries among all substructures compatible and equilibrated. An Interuet-based data exchange scheme is also devised to transfer data among computers equipped with different software environments. A series of online hybrid tests are introduced, and the portability, flexibility, and extensibility of the online hybrid test system are demonstrated.

Temperature Control and Simulation of Temperature-Altitude Test System

The temperature-Altitude Test System(TATS) supplies various testing environments.The traditional PID method controls the temperature in TATS Temperature-Pressure Cabin(TPC) over a long adjusting time and with a large overshoot.In order to solve this problem simply,a temperature control strategy with temperature difference corresponding factors is presented through a dynamic analysis and modeling of TPC temperature change.The TPC temperature descending process is simulated,and the results show that this control strategy can allot the proportion of PID heating controller and PID cooling controller in the whole control process and TPC temperature can be controlled at a set point quickly and effectively.

NUMERICAL MODELING OF MULTI-CYLINDER ELECTRO-HYDRAULIC SYSTEM AND CONTROLLER DESIGN FOR SHOCK TEST MACHINE

A high fidelity dynamic model of a high-energy hydraulically-actuated shock test machine for heavy weight devices is presented to satisfy the newly-built shock resistance standard and simulate the actual underwater explosion environments in laboratory as well as increase the testing capability of shock test machine. In order to produce the required negative shock pulse in the given time duration, four hydraulic actuators are utilized. The model is then used to formulate an advanced feedforward controller for the system to produce the required negative waveform and to address the motion synchronization of the four cylinders. The model provides a safe and easily controllable way to perform a ＂virtual testing＂ before starting potentially destructive tests on specimen and to predict performance of the system. Simulation results have demonstrated the effectiveness of the controller.

TEST AND CONTROL SYSTEM DEVELOPMENT AND APPLICATION OF LANDING GEAR DROP TEST RIG

A control and test system of a landing gear drop test rig is developed considering the drop test specifica- tions for the ＂Seagull 300＂ multi-functional amphibious airplane. In order to realize the automation of drop test process, a servo system is proposed and programmable logic controller（PLC） technology is used. Several key technologies for measuring the horizontal load, the vertical load and the transient rotational speed are studied. According to the requirements of CCAR-23-R3, the drop test of landing gears of the ＂Seagull 300＂ airplane is accomplished. Test results show that the system has a high accuracy of data collection. The system is stable and reliable. The drop test satisfies the requirements of the drop test specifications and the results can be used as the certification of airworthiness for this kind of airplane.

Automatic test system development for digital beam position monitor of HEPS and BEPCII

Purpose Hundreds of digital beam position monitor processors(DBPM)are required to be produced during the construction of projects such as High Energy Photon Source(HEPS)and the upgrade project of the Beijing Electron Positron Collider(BEPCII),which brings great challenges to the test work.In order to achieve accurate,fast,and complete mass production tests of DBPMs,an automatic test system(ATS)has been developed in this article.Methods According to the test items of DBPM,the standardized testing softwareflow is designed based on virtual instru-ment program control technology and experimental physics and industrial control system(EPICS),which realize automatic adjustment of test parameters and automatic acquisition of test result data.Results and conclusions The ATS can realize one-button testing of channel coefficients,channel linearity,attenuator linearity,beam current dependence(BCD)and sampling signal-to-noise ratio(SNR),and generate test reports.The total test time is less than 3 minutes,which is significantly more efficient compared to manual testing.More than 90 BEPCII DBPMs has been tested by this ATS in the lab.The test results proved that such a system could automatically recognize defective products and satisfy the requirements of mass testing.

Shaking table test and numerical analysis of offshore wind turbine tower systems controlled by TLCD

A wind turbine system equipped with a tuned liquid column damper （TLCD） is comprehensively studied via shaking table tests using a 1/13-scaled model. The effects of wind and wave actions are considered by inputting response- equivalent accelerations on the shaking table. The test results show that the control effect of the TLCD system is significant in reducing the responses under both wind-wave equivalent loads and ground motions, but obviously varies for different inputs, Further, a blade-hub-tower integrated numerical model for the wind turbine system is established. The model is capable of considering the rotational effect of blades by combining Kane＇s equation with the finite element method. The responses of the wind tower equipped with TLCD devices are numerically obtained and compared to the test results, showing that under both controlled and uncontrolled conditions with and without blades＇ rotation, the corresponding responses exhibit good agreement. This demonstrates that the proposed numerical model performs well in capturing the wind-wave coupled response of the offshore wind turbine systems under control. Both numerical and experimental results show that the TLCD system can significantly reduce the structural response and thus improve the safety and serviceability of the offshore wind turbine tower systems. Additional issues that require further study are discussed.

2-D algebraic test for robust stability of time-delay systems with interval parameters

The robust stability test of time-delay systems with interval parameters can be concluded into the robust stability of the interval quasipolynomials. It has been revealed that the robust stability of the quasipolynomials depends on that of their edge polynomials. This paper transforms the interval quasipolynomials into two-dimensional （2-D） interval polynomials （2-D s-z hybrid polynomials）, proves that the robust stability of interval 2-D polynomials are sufficient for the stability of given quasipolynomials. Thus, the stability test of interval quasipolynomials can be completed in 2-D s-z domain instead of classical 1-D s domain. The 2-D s-z hybrid polynomials should have different forms under the time delay properties of given quasipolynomials. The stability test proposed by the paper constructs an edge test set from Kharitonov vertex polynomials to reduce the number of testing edge polynomials. The 2-D algebraic tests are provided for the stability test of vertex 2-D polynomials and edge 2-D polynomials family. To verify the results of the paper to be correct and valid, the simulations based on proposed results and comparison with other presented results are given.

Study on soil-pile-structure-TMD interaction system by shaking table model test

The success of the tuned mass damper (TMD) in reducing wind-induced structural vibrations has been well established. However, from most of the recent numerical studies, it appears that for a structure situated on very soft soil, soil-structure interaction (SSI) could render a damper on the structure totally ineffective. In order to experimentally verify the SSI effect on the seismic performance of TMD, a series of shaking table model tests have been conducted and the results are presented in this paper. It has been shown that the TMD is not as effective in controlling the seismic responses of structures built on soft soil sites due to the SSI effect. Some test results also show that a TMD device might have a negative impact if the SSI effect is neglected and the structure is built on a soft soil site. For structures constructed on a soil foundation, this research verifies that the SSI effect must be carefully understood before a TMD control system is designed to determine if the control is necessary and if the SSI effect must be considered when choosing the optimal parameters of the TMD device.

Multiple UIO-based test sequence generation for distributed systems

In developing distributed systems, conformance testing is required to determine whether an implementation under test （IUT） conforms to its specification. With distributed test architectures involving multiple remote testers, testing approaches may become more complicated because of issues known as controllability and observability problems. Based on a finite state machine （FSM） representation of the system＇s specification, this paper proposes a new method to generate a test sequence utilizing multiple UIO sequences. The method is essentially guided by the way of minimizing the use of external coordination messages and input/output operations. Experiments are given to evaluate the proposed method.

Remote Control and Telemetry System for Large-scale Model Test at Sea

Physical testing of large-scale ship models at sea is a new experimental method.It is a cheap and reliable way to research the environment adaptability of a ship in complex and extreme wave conditions.It is necessary to have a stable experimental system for the test.Since the experimental area is large, a remote control system and a telemetry system are essential, and were designed by the authors.An experiment was conducted on the Songhuajiang River to test the systems.The relationship between the model's speed and its electromotor's revolutions was also measured during the model test.The results showed that the two systems make it possible to carry out large-scale model tests at sea.

A test sequence generation method of zone controller based on timed automata

In order to solve the problem of artificial generation and low efficiency of test sequences for zone controller (ZC), a model-based automatic generation method of test sequence is proposed. Firstly, the timed automata model is established based on function analysis of the zone controller, and the correctness of the model is verified by UPPAAL. Then by parsing the timed automata model files, state information and transition conditions can be extracted to generate test case sets. Finally, according to the serialization conditions of test cases, the test cases are serialized into test sequences by using the improved depth first search algorithm. A case, the ZC controls the train running within its jurisdiction, shows that the method is correct and can effectively improve the efficiency of test sequence generation.

APPLICATION OF NONLINEAR PID CONTROLLER IN AERODYNAMICS LOADING SYSTEM

The design idea of tracking-differentiator and the nonlinear PID controllerare introduced, the applicable algorithm and its real result for distributed aerodynamicsloading control system are discussed, and the construction of the test & contro1 system arealso presented. The application shows that the nonlinear PID algorithm has the advan-tages of high reliability, short run time and strong stability.

Control System Design and Implementation at Flexible, Distributed Offshore Sensor Test Sites in the Yangtze Estuary Area

Marine in situ testing is a necessary step for stereotyping newly developed marine sensors. The use of test sites in the Yangtze Estuary area, which has high turbidity and abundant nutrients, can effectively reduce the needed testing time owing to its harsh conditions. Five test stations were established, and a floating buoy and fixed test equipment were designed. A control system, including a sensor connection, data processor, video remote transmission, and corresponding control algorithm, was developed. The control system enabled the nondestructive monitoring of biological attachments and bidirectional, real-time communication between an upper server on land and the control system at the test sites. The dissolved oxygen(DO), temperature, and pH data of DOS600 and DPS600 sensors were compared with those of AP2000 sensors. Temperature recording using the DOS600 sensor was performed nearly as well as that of the AP2000 sensor. The mean DO values(standard deviations) were 8.414 mg L-1(2.068) and 6.896 mg L-1(1.235) for the DOS600 and AP2000 sensors, respectively, indicating that the DOS600 performance was unsatisfactory. The pH recording of the DPS600 was slightly worse than that of the AP2000 sensor. Experimental results showed that the DO value was more easily affected by the buoy movement of waves compared to the pH and temperature. Moreover, data fluctuations showed that the DO and pH parameters were more vulnerable to biofouling than temperature. Waves and biofouling create a harsh test environment, and the performance difference between the developed sensors and a standard sensor can be obtained in a short time period.

An Advanced Control Strategy for Dual-Actuator Driving System in Full-Scale Fatigue Test of Wind Turbine Blades

A new dual-actuator fatigue loading system of wind turbine blades was designed.Compared with the traditional pendulum loading mode,the masses in this system only moved linearly along the loading direction to increase the exciting force.However,the two actuators and the blade constituted a complicated non-linear energy transferring system,which led to the non-synchronization of actuators.On-site test results showed that the virtual spindle synchronous strategy commonly used in synchronous control was undesirable and caused the instability of the blade’s amplitude eventually.A cross-coupled control strategy based on the active disturbance rejection algorithm was proposed.Firstly,a control system model was built according to the synchronization error and tracking error.Furthermore,based on arranging the transition process,estimating the system state and error feedback,and compensating disturbance,an active disturbance rejection controller was designed by adopting the optimal control function.Finally,on-site test results showed that the cross-coupled control strategy based on the active disturbance rejection algorithm could ensure the synchronization of two actuators.The maximum speed synchronization error of the two motors was less than 16 RPM,the displacement synchronization error of the two actuators was less than 0.25 mm and approaching zero after 4 seconds,and the peak value of vibration of the blade was less than 5 mm,which satisfied the fatigue test requirement.

Study of Traction Motor Feedback Testing SystemControlled by Microcomputer

this paper describes the design of a feedback testing system for locomtive tractionmotor. The structures and features of the software and hardware of themicrocomputer control system have been studied. This testing system hasalready been put into operation successfully in several locomotive depots inChina.

Smart Inverter Functionality Testing for Battery Energy Storage Systems

Variable distributed energy resources (DERs) such as photovoltaic (PV) systems and wind power systems require additional power resources to control the balance between supply and demand. Battery energy storage systems (BESSs) are one such possible resource for providing grid stability. It has been proposed that decentralized BESSs could help support microgrids (MGs) with intelligent control when advanced functionalities are implemented with variable DERs. One key challenge is developing and testing smart inverter controls for DERs. This paper presents a standardized method to test the interoperability and functionality of BESSs. First, a survey of grid-support standards prevalent in several countries was conducted. Then, the following four interoperability functions defined in IEC TR 61850-90-7 were tested: the specified active power from storage test (INV4), the var-priority Volt/VAR test (VV) and the specified power factor test (INV3) and frequency-watt control (FW). This study then out-lines the remaining technical issues related to basic BESS smart inverter test protocols.

Optimal Multiperiodic Control for Inventory Coupled Systems: A Multifrequency Second-Order Test

A complex autonomous inventory coupled system is considered. It can take, for example, the form of a network of chemical or biochemical reactors, where the inventory interactions perform the recycling of by-products between the subsystems. Because of the flexible subsystems interactions, each of them can be operated with their own periods utilizing advantageously their dynamic properties. A multifrequency second-order test generalizing the p-test for single systems is described. It can be used to decide which kind of the operation (the static one, the periodic one or the multiperiodic one) will intensify the productivity of a complex system. An illustrative example of the multiperiodic optimization of a complex chemical production system is presented.