Sea spray induced air-sea heat and salt fluxes based on the wavesteepnessdependent sea spray model

Sea spray,which comprises amounts of small ocean droplets,plays a significant role in the air-sea coupling,atmospheric and oceanic dynamics,and climate.However,it remains arduous to arrive at estimates for the efficiency and accuracy of the sea spray induced air-sea heat and salt fluxes.This is because the microphysical process of sea spray evolution in the air is of extreme complexity.In this study,we iteratively calculated the sea spray induced air-sea heat and salt fluxes at various weather condition.To do so,we implemented one novel wave-steepness-dependent sea spray model into a bulk air-sea fluxes algorithm and utilized other sea spray models as comparisons.Based on the improved wave-dependent bulk turbulent algorithm,we observed that despite the negative contribution of sea spray to the sensible heat fluxes,the sea spray positively contributes to the air-sea latent heat fluxes,leading to an overall increase in the total air-sea heat fluxes.The additional heat fluxes caused by sea spray may be the missing critical process that can clarify the discrepancies observed between measured and modelled Tropical Cyclone’s development and intensification.In addition to heat fluxes,we observed that sea spray has significant impacts on the air-sea salt fluxes.As the sea salt particles are one of the main sources of the atmosphere aerosol,our results imply that sea spray could impact global and regional climate.Thus,given the significance of sea spray on the air-sea boundary layer,sea spray effects need to be considered in studies of air-sea interaction,dynamics of atmosphere and ocean.

LPCS Ni-Zn-Al_(2)O_(3) Intermediate Layer Enhanced SPS NiCr-Cr_(3)C_(2) Coating with Higher Corrosion and Wear Resistances

The double-layer NiCr-Cr_(3)C_(2)/Ni-Zn-Al_(2)O_(3) coatings with sufficient corrosion and wear resistance were prepared on low carbon steel substrates.The intermediate layers Ni-Zn-Al_(2)O_(3) were fabricated by using low-pressure cold spray (LPCS) method to improve the salt fog corrosion resistance properties of the supersonic plasma spray (SPS) NiCr-Cr_(3)C_(2) coatings.The friction and wear performance for the double-layer and single-layer NiCr-Cr_(3)C_(2) coatings were carried out by line-contact reciprocating sliding,respectively.Combined with the coating surface analysis techniques,the effect of the salt fog corrosion on the tribological properties of the double-layer coatings was studied.The results showed that the double-layer coatings exhibited better wear resistance than that of the single-layer coatings,due to the better corrosion resistance of the intermediate layer;the wear mass losses of the double-layer coatings was reduced by 70%than that of the single layer coatings and the wear mechanism of coatings after salt fog corrosion conditions is mainly corrosion wear.

Preparation and Properties of Spray Polyurea Elastomer for Aquaculture Foam Floating Balls

[Objectives] This study was conducted to develop a polyurea elastomer which can be sprayed on the surface of expanded polystyrene (EPS) floating balls, so as to improve the surface strength and service life of the floating balls. [Methods] The effects of the types and amounts of isocyanate, chain extenders and polyether polyols on the gelation rate, adhesion and wear resistance of polyurea elastomer were investigated, and it was finally determined the preparation process of polyurea elastomer using liquid isophorone diisocyanate (IPDI) and amino-terminated polyether (D2000) as the main raw materials, dimethylthiotoluene diamine (E300) as the chain extender and silica as the wear resistance modifier through two-step solution polymerization of prepolymerization and chain extension. [Results] The physical properties and chemical resistance tests of spray polyurea elastomer showed that it had good physical properties and acid and alkali resistance, and could meet the requirements of spraying and protection of EPS floating ball surface in marine environment. [Conclusions] Polyurea elastomer coating can improve the aging resistance, wear resistance and acid and alkali resistance of EPS floating balls, and prevent them from being fragile and floating randomly to form marine floating garbage which results in "white pollution".

Growth and physiological responses of four kiwifruit genotypes to salt stress and resistance evaluation

In this study,four genotypes(Acva-1,Acva-2,Acva-3 and ZM-2) of Actinidia germplasm resources were grown in different NaCl concentrations(0,0.4,0.8 and 1.2 g L–1).The growth,physiological and biochemical indicators were measured,and a graded scale was developed as the salt damage index(SDI) according to different damage symptoms in leaves.The results showed SDI increased gradually,and average number and length of new shoot decreased significantly.Three antioxidant enzymes(superoxide dismutase,peroxidase and catalase) and two osmotic adjustment substances(soluble sugar and proline) showed different changes in old and new leaves of four genotypes.SPAD values exhibited a decreased trend in the whole except in the new leaves of Acva-2.Malonaldehyde contents increased and root activity decreased with the increasing salt concentrations.Principal component analysis was used to assess the salt tolerance,and the results showed Acva-3,from Actinidia valvata Dunn.,had the strongest tolerance to salt,and could be a potential resistant resource to the salt-tolerance dedicated rootstock breeding of kiwifruit.

Effect of Salt Spray Corrosion on Tribological Properties of HVOF Sprayed NiCr-Cr3C2 Coating with Intermediate Layer

The objective of the present work was to determine the influence of the neutral salt spray corrosion on the wear resistance of HVOF sprayed NiCr-Cr3C2 coating with intermediate layer. Ni-Zn-Al2O3 coatings as interlayers were prepared by low pressure cold spray（LPCS） between NiCr-Cr3C2 cermet coatings to form a sandwich structure to enhance the corrosion resistance properties. The tribological properties were examined using the UMT-3 fricition and wear tester by line-contact reciprocating sliding under dry and salt spray one week corrosion. The morphology, element distribution, and phase compositions of the coating and worn sufaces were analyzed by using scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction respectively. The corrosion behavior of the coating was studied by the open-circuit potential, the electrochemical impedance spectroscopy, potentiodynamic polarization, and salt spray corrosion methods. It is found that the sandwich structured coating has better corrosion resistance than the single layer coating. The results show that under dry wear conditions, the wear mechanism is abrasive and adhesive wear, whereas under salt spray corrosion conditions it becomes corrosion wear. The friction coefficient of the sandwich structured coating after salt spray corrosion is slightly lower than the dry friction coefficient, but the weight of the wear loss is lower than that under dry condition.

Salt spray corrosion test of micro-plasma oxidation ceramic coatings on Ti alloy

Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation （MPO）. The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.

The corrosion behaviors of Mg-7Gd-5Y-1Nd-0.5Zr alloy under(NH4)_(2)SO_(4),NaCl and Ca(NO_(3))_(2)salts spray condition

The corrosion behaviors of Mg–7Gd–5Y–1Nd–0.5Zr alloys after T5 treatment under(NH4)_(2)SO_(4),NaCl and Ca(NO_(3))_(2)salt spray condition were investigated by weight loss rates,residual mechanical properties,scanning electron microscope(SEM),X-ray Diffraction(XRD)and potentiodynamic polarization tests.The corrosion degree of Mg–7Gd–5Y–1Nd–0.5Zr alloys in Ca(NO_(3))_(2)salt spray was very shallow by corrosion morphology and the corrosion route was extended along the surface in texture-like shape,while the alloy in NaCl and(NH4)_(2)SO_(4)salt spray were major local corrosion and there were serious corrosion pits on the surface.The weight loss rates in(NH4)_(2)SO_(4),NaCl and Ca(NO_(3))_(2)salt spray was respectively 0.4147,0.1618 and 0.0725 mg/(cm2 d−1).The results of residual mechanical properties indicated that the corrosion order in salts spray of Mg–7Gd–5Y–1Nd–0.5Zr alloys is NH4SO4>NaCl>Ca(NO_(3))_(2),which was consistent with the results of potentiodynamic polarization tests.The type of the salts will play a vital role in the initiation of the corrosion of EW75 alloy when they are used in the atmosphere environments.Inorganic salts with the smaller PH value after dissolution will have a stronger impact on the corrosion of EW75 magnesium alloys.

The Surface Morphologies and Spectroscopy Analysis of VC Coatings on the Substrate of Cr12MoV Prepared by TD Process after Salt Spray

The normal temperature corrosion of VC coating on the substrate of Cr12MoV prepared by TD process was tested in 5% NaCl aqueous solution, its surface morphologies and corrosion components after salt spray were observed with SEM and EDS, respectively, and the effects of salt spray on micro-structures of VC coating were analyzed. Moreover, the invalidation mechanism of VC coating after salt spray and its effect on substrate material were discussed. The experimental results shown that the uniformity and integrity of VC coating surface are destroyed by salt spray for 120 h, a large number of the pits are produced on the coating surface, and the coating falls off, which speeds corrosion breakage of its substrate; the oxidated film on its surface becomes rougher, broken and discontinuous, and falls off easily, which reduce the ability of resistance salt spray; the failure modes of VC coating after salt spray are expressed with falling off of oxidated film, stress concentration and pore effect and so on, the corrosion breakage of oxidated film is the corrosion result of deoxidization corrosion from oxygen and HCl produced by NaCl and vapor.

Characterization of salt tolerance and Fusarium wilt resistance of a sweetpotato mutant

The variant LM1 was previously obtained using embryogenic cell suspension cultures of sweetpotato variety Lizixiang by gamma-ray induced mutation, and then its characteristics were stably inherited through six clonal generations, thus this mutant was named LM1. In this study, systematic characterization of salt tolerance and Fusarium wilt resistance were performed between Lizixiang and mutant LM1. LM1 exhibited significantly higher salt tolerance compared to Lizixiang. The content of proline and activities of superoxide dismutase（SOD） and photosynthesis were significantly increased, while malonaldehyde（MDA） and H_2O_2 contents were significantly decreased compared to that of Lizixiang under salt stress. The inoculation test with Fusarium wilt showed that its Fusarium wilt resistance was also improved. The lignin, total phenolic, jasmonic acid（JA） contents and SOD activity were significantly higher, while H_2O_2 content was significantly lower in LM1 than that in Lizixiang. The expression level of salt stress-responsive and disease resistance-related genes was significantly higher in LM1 than that in Lizixiang under salt and Fusarium wilt stresses, respectively. This result provides a novel and valuable material for improving the salt tolerance and Fusarium wilt resistance of sweetpotato.

Chemically Induced Mutants of <i>Brassica oleracea var. botrytis</i>Maintained Stable Resistance to Drought and Salt Stress after Regeneration and Micropropagation

Investigation was made to confirm the stability of drought and salt stress tolerance in cauliflower (Brassica oleracea var.botrytis) mutants after regeneration and micropropagation. The N-nitroso-N-ethyleurea (NEU) and N-nitroso-N-methylurea (NMU) induced mutants of cauliflower were created and screened for drought and salt stress tolerance. The highly tolerant mutants were selected, regenerated by tissue culture techniques, screened again for drought and salt tolerance under in-vitro and in-vivo conditions, correlated the response of in-vitro and in-vivo plants within a clone. Free proline levels in clones were correlated with stress tolerance. Results confirmed the persistence of mutations in clones with enhanced resistance levels to stresses over control plants. The regenerated in-vitro and in-vivo plants within a clone showed a positive significant correlation for drought (R2 = 0.663) and salt (R2 = 0.647) resistance that confirms the stability of mutation in clones after generations. Proline showed a positive and significant correlation with drought (R2 = 0.524) and salt (R2 = 0.786) tolerance. Conclusively, drought and salt resistance can be successfully enhanced in cauliflower by chemical mutagenesis. Further molecular analysis is recommended to study these mutants.

Improving Wear Resistance of the Ni-base Thermal Spray-Welding Coating Using Rare Earths

By adding rare earth alloy and cerium oxide, the effect of rare earths on tribological properties of nickel base alloy layer was studied to approach the possibility of applying rare earths to Ni base thermal spray welding coating. Wear test results showed that the wear rates of the nickel base coating without rare earths were quite high, and the load bearing capacity of coating was low, in contrast, the wear rates of the coating with rare earths were low and the coating had higher load bearing capacity. The results show that rare earths can refine the structure of nickel base alloy, improve the interface of the coating and substrate.

Preparation, characterization and salt-resistance of a coal based super absorbent composite

Potassium humate was extracted from brown coal. A novel super absorbent composite, poly (acrylic acid-co-acryla-mide)/potassium humate (PAA-AM/KHA), was prepared by graft polymerization of acrylic acid, acrylamide and coal based potas-sium humate using N, N’-methylenebisacrylamide as a crosslinker and potassium peroxydisulfate as an initiator. The effects of reaction temperature, degree of neutralization of the poly (acrylic acid) and the amounts of crosslinker, initiator and potassium hu-mate were investigated. Salt resistance tests were also carried out. The composite prepared under optimal conditions had a potas-sium humate content of 10% and exhibited a water absorption of 770 g/g in distilled water, and 349, 286 and 41 g/g in 0.5 mol/L KCl, MgCl2 and AlCl3 solutions respectively. The results indicate that the salt resistance of PAA-AM/KHA was superior to that of poly (acrylic acid-co-acrylamide) because of the collaborative effect of functional groups of the coal based potassium humate. The PAA-AM/KHA micro powder was characterized by IR spectroscopy and the micrographic surface was characterized by scanning electron microscopy. Introduction of potassium humate into the poly (acrylic acid-co-acrylamide) structure creates a composite more suitable for use as a water-managing material in the renewal of arid and desert environments. The salt resisting property of the composite is improved, production costs are reduced and the growth stimulant effect is still present.

Effects of laser heat treatment on salt spray corrosion of 1Cr5Mo heat resistant steel welding joints

The surface of 1Cr5 Mo heat-resistant steel welding joint was processed with CO2 laser, and the corrosion behaviors before and after laser heat treatment(LHT) were investigated in the salt spray corrosion environments. The microstructures, phases, residual stresses and retained austenite content of 1Cr5 Mo steel welding joint before and after LHT were analyzed with optical microscope and X-ray diffraction, respectively. The cracking morphologies and chemical compositions of corrosion products after salt spray corrosion were analyzed with field emission scanning electron microscopy(FESEM) and energy disperse spectroscopy(EDS), respectively, the polarization curves were measured on a PS-268 A type electrochemical workstation, and the mechanism of corrosion resistance by LHT was investigated as well. The results show that the passive film of original sample is destroyed owing to the corrosive media penetrating into the subsurface, resulting in the redox reaction. The content of residual austenite in the surface and the self-corrosion potential are increased by LHT, which is contributed to improving the capability of salt spray corrosion resistance.

Resistance of the diffusive boundary layer to salt release from saline sediments to freshwater

The diffusive boundary layer （DBL） is the zone for matter exchange between surface water and aquatic sediments. To elucidate the influence of DBL on salt release from saline sediments to freshwater, two experiments with or without wind blowing were conducted. According to the experiments, a 3.5 cm DBL is formed above the smoothed sediments at a steady wind field and this thickness is greater than other studies. The observed flux of salt through the DBL is 6% larger than the calculated value from Fick＇ s first law. The results indicate that molecular diffusion is the dominant mechanism for salt transport through the DBL. The presence of DBL suppresses the hydrodynamic enhancement for matter exchange between sediments and overlying water. Therefore, salts in the sediments of a polder reservoir may influence the water quality chronically.

Influence of CeO_2 on the Microstructure and Wear Resistance of M_(80)S_(20) Thermal Spray and Thermal Spray Welding Coatings

The influence of rare earth oxide CeO_2 on microstructure and wear resistance of M_(80)S_(20) thermal spray and thermal spray welding coatings is studied using optical microscope,scanning electron microscope,X-ray energy dispersion spectroscope,X-ray diffractometer and wear testing machine.The results show that the addi- tion of 8% CeO_2 can improve the microstructure,microhardness and wear resistance of coatings significantly.

CORROSION FATIGUE OF HSLA STEELS IN SALT SPRAY

The corrosion fatigue propagation behaviour of high strength low alloy Cr-Ni and Si-Mn steels has been investigated in 3.5 %NaCl solution spryly at the frequencies of 0.1 and 5.5 Hz. It was shown that the fatigue crack initiation resistances of the two steels are significantly re- duced in salt spray;the fatigue crack growth rates of steels increase with the decrease of fre- quency and are much higher in salt spray than in air within low ΔK range.A critical stress in- tensity factor was observed for each steel and the crack growth stoppage will occur if the ΔK values are lower than it.It was found that the active dissolution makes great contribution to the fatigue crack growth within low ΔK range.

Composites Based on GM(1,1)-Markov in the Salt Spray Corrosion Environment

This study was designed to solve the problem of magnesium hazards due to potash extraction in the salt lake region.Using basalt fiber(BF)as the reinforcement material and magnesium oxychloride cement(MOC)as the gelling material,a BF/MOC composite material was prepared.Firstly,the effect of BF addition content on the basic mechanical properties of the composites was investigated.Then,through the salt spray corrosion test,the durability damage deterioration evaluation analysis was carried out from both macroscopic and microscopic aspects using mass change,relative dynamic modulus of elasticity(RDME)change,SEM analysis and FT-IR analysis.Finally,a GM(1,1)-Markov model was established to predict the durability life of composite materials by using durability evaluation indicators.The results show that:when the BF content is 0.10%(by volumetric content),the composites have the best mechanical properties and resistance to salt spray corrosion.However,when the volume of BF content exceeds 0.10%,a large number of magnesium salt crystallization products are observed from the microscopic point of view,and the corrosion of the main strength phase of MOC is more serious.The prediction results of the GM(1,1)-Markov model are highly identical with the raw data.In addition,using the change of RDME as a predictor,RDME is more sensitive to environmental factor compared to the change of mass.Predictions using the change of RDME as a threshold indicate that MOC-BF0.10 has the longest durability life,which is 836 days.The model is important to promote the application of MOC composites in the salt lake region and to promote the healthy development of green building materials.

Electrochemical corrosion failure mechanism of M152 steel under a salt-spray environment

The corrosion failure mechanism of M152 was studied using the neutral salt-spray test to better understand the corrosion behavior of 1Cr12Ni3Mo2VN（M152）, provide a basis for the optimization of material selection, and prevent the occurrence of failure. Moreover, the mechanism was investigated using the mass loss method, polarization curves, electrochemical impedance spectroscopy（EIS）, stereology microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy（EDS）. The results show that M152 steel suffers severe corrosion, especially pitting corrosion, in a high-salt-spray environment. In the early stage of the experiment, the color of the corrosion products was mainly orange. The products then gradually evolved into a dense, brown substance, which coincided with a decrease of corrosion rate. Correspondingly, the EIS spectrum of M152 in the late test also exhibited three time constants and presented Warburg impedance at low frequencies.

Enhancement of Corrosion Resistance of NiCrFeBSi Coatings Obtained by Flame Thermal Spray Process Adding an Electroless Nickel Coating Ni-P

Flame Thermal Spray (FTS) coatings frequently show some porosity and reduced adherence to substrate, which affect its properties, especially its corrosion resistance. In this work, the corrosion resistance of AISI 1018 carbon steel coated by different methods is compared: electroless nickel (EN) coating, NiCrFeBSi obtained by FTS, duplex coatings of an EN deposit on a layer of NiCrFeBSi obtained by FTS and a layer of NiCrFeBSi on an EN deposit. The coatings were characterized using optical microscopy and scanning electron microscopy techniques, EDS microprobe microanalysis, roughness as well as electrochemical polarization tests to obtain the corrosion rate. The results show the enhancement in the corrosion resistance in saline medium of the duplex coatings, especially of the EN coating on FTS layer.

Continuing Results for Effervescent Aerosol Salt Water Spray Nozzles Intended for Marine Cloud Brightening

Marine Cloud Brightening (MCB) by effervescent spray atomization of mixed sea water brine with air is a candidate for solar radiation management to compensate for global warming. We discovered that the flow from mixing tee nozzle described earlier had occasional unstable slug flow. A new design that adding rotational swirl to the salt brine as it is mixed into the air stabilized the nozzle flow and no longer showed slug flow in spray pictures. Flow equations were developed for the relatively low speed of sound of a choked flow mixed brine and air nozzle. Experimental mixed flow measurements with 300b pressure and a 200 μm diameter nozzle and calculations using perfect gas, and isotropic processes equations compared well with the chocked flow equations. Analysis in EXCEL of particle sizers measurements from both a scanning mobility particle sizer (SMPS) and an aerodynamic particle sizer (APS) showed production of many nanometer sized particles estimated as usable for MCB. A small number of micron sized particles were also always present but with about 90% of the sprayed mass. This is a first report with good data over the complete size range. The micron sized particles measured were similar to the measurements of earlier reports which reported no nanometer sized particles. We hypothesize that many nano-particles are always produced by liquid-air effervescent sprays, but earlier, were not observed because SMPS instruments were not available. The presence of the large mass percentage of large particles in the spray may cause problems by evaporative cooling preventing the rise of the MCB particles. We suggest future systems design with an impactor filter to remove the large particles. Calculations combining increased brine concentration, lower pressure, and larger nozzle area showed that significant reductions in required power and number of nozzles could be realized. An EXCEL model is developed to calculate flow from experimental analysis equations and compare with mixed choked flow equations. Solving with the model predicted the power required and the number of nozzles required to produce 1015 particles/s. The model showed that increasing brine concentration strongly lowered total power. Lowering pressure decreased power and increased number of nozzles. Increasing nozzle area lowered the number of nozzles. This model predicted that, at 300b pressure and 200μm diameter nozzle as the experiment but using an increased brine concentration of 0.1 instead of 0.032 would require only 115 nozzles instead of 358 and power of 146 kw instead of 493 kw. Combining increased brine concentration, lower pressure, and larger nozzle area, the model predicted that with a 1 mm diameter nozzle at 30b pressure and salt concentration of 0.2, the nozzle count and power required would drop to only 24 nozzles and power of 28 kw. Whether extending the model to these conditions is valid is not known but suggests further development should be investigated. Filtering out and reusing the 90% or greater large particles mass sprayed combined with the lower power advantage of higher brine concentration is suggested for future systems.