Design of foundation structures of sea-crossing bridges on serviceability limit state

The target reliability indices of the foundation structures of sea-crossing bridges on the serviceability limit state （SLS） are different from those of common bridges due to their different surroundings. Consequently, three levels of the target reliability indices, which are 1.5, 2. 0 and 2. 3, respectively, for those structures on the SLS are suggested based on the Joint Committee on Structural Safety （JCSS） model code, and a new method of calibrating factors of live loads, which is based on the contribution ratio of tensile stresses of reinforcing bars produced by various loads to the maximum crack width of concrete, is proposed. Finally, the calibration of the reliability-based factors of the frequent value and the quasi-permanent value of live loads is conducted by the Joint Committee （JC） method through an actual design, and the indices are proved to be reasonable and the new method is proved to be feasible.

Reliability Analysis of Numerical Simulation of Sea-Crossing Bridge Deformation Under Wave Forces

To study on the numerical simulation calculation reliability of sea-crossing bridge under complex wave forces,the paper applied GPS deformation monitoring and numerical simulation calculation by researching Qingdao Jiaozhou Bay Sea-Crossing Bridge.The db3 wavelet three-layer decomposition was used on the horizontal movement of the sea-crossing bridge and the wind speed of the waves to analyze their correlation.The complex wave forces value of Qingdao Jiaozhou Bay Sea-Crossing Bridge was loaded on FLAC3D software successfully to make numerical simulation calculation of bridge deformation.Since the accuracy of the GPS deformation monitoring reaches millimeter level,it was used to monitor the exact value of the bridge deformation to judge the reliability of numerical simulation.The relative errors of displacement in X,Y and Z directions were between 33%and 41%through comparison.It could be seen that the numerical simulation error was relatively large,which was mainly due to various environmental factors and the deviation of applied wave forces.However,numerical simulation generally reflects the deformation law of the sea-crossing bridge under complex wave forces,providing an effectively technical support for the safe operation assessment of the sea-crossing bridge.

Scour effect on a sea-crossing bridge under combined action of service and extreme seismic loads

Foundation scour is an important cause for structural failure of sea-crossing bridges. Usually, the sea-crossing bridges operate under the harsh natural environment in which service wind, wave and vehicle loads are stronger and extreme loads such as earthquake, hurricane, and ship collision, are more frequent. As a result of the foundation scour,the dynamic behavior of bridge under different combined action of service and extreme loads may be further escalated.In particular, this work has investigated the scour effect on a sea-crossing bridge under service wind, wave and vehicle loads as well as extreme seismic loads. The dynamic coupled earthquake-wind-wave-vehicle-bridge(EWWVB) system is established by considering the interactions within the system, and the p-y curve method is used to calculate the loaddisplacement relation of the pile and soil under various levels of foundation scour. After that, a case study has been performed on a cable-stayed bridge with foundation scour. The results indicate that the dynamic characteristics of bridge structure will change after considering bridge scour, and the dynamic responses of bridge and vehicle will be affected to different degrees under service and seismic loads considering bridge scour.

Pavement structure and materials design for sea-crossing bridges and tunnel:Case study of the Hong Kong-Zhuhai-Macao Bridge

With the continuous development of bridge and tunnel construction technologies,large-scale sea-crossing bridges and tunnels have gradually become the preferred choice for regional traffic.The construction technology of Hong Kong-Zhuhai-Macao Bridge(HZMB),one of the most representative sea-crossing passageways,is instructive for the construction of other large sea-crossing infrastructures.At present,the pavement design method of sea-crossing passageways lacks pertinence as it still refers to specifications for design of common pavement.Therefore,it is necessary to consider the bridge and tunnel pavement of HZMB as a typical example to analyze key technical problems encountered in its design,construction and operation.Novel solutions for material selection and structural design built upon the analysis of such critical problems should thus follow up.Based on comprehensive literature research,it can be found that environmental variability,tunnel closure,structural differential settlement and expansion deformation are the key technical problems faced by pavement of sea-crossing passageways.In view of the environmental variability,the steel deck-paving material and structure design of GMA-10 t SMA-13 is innovatively proposed.As for the closure of immersed tube tunnel,warm-mix flame retardant asphalt mixture is used to control pavement design through key indexes such as temperature and limit oxygen index.Regarding the deformation of immersed pipe joints,BJ200 asphalt seamless expansion joint material is introduced,which effectively satisfies the multi-directional deformation between pipe joints and ensures the smoothness of the road surface and driving comfort.For segmental joints,double-layer waterproof-coiled material is used to effectively prevent reflective cracks while ensuring the continuity of asphalt concrete pavement.Therefore,this paper provides a panel of ideas and methods for the pavement design of the same type of sea-crossing passageways.

Bayesian operational modal analysis of a long-span cable-stayed sea-crossing bridge

Sea-crossing bridges have attracted considerable attention in recent years as an increasing number of projects have been constructed worldwide.Situated in the coastal area,sea-crossing bridges are subjected to a harsh environment(e.g.strong winds,possible ship collisions,and tidal waves)and their performance can deteriorate quickly and severely.To enhance safety and serviceability,it is a routine process to conduct vibration tests to identify modal properties(e.g.natural frequencies,damping ratios,and mode shapes)and to monitor their long-term variation for the purpose of early-damage alert.Operational modal analysis(OMA)provides a feasible way to investigate the modal properties even when the cross-sea bridges are in their operation condition.In this study,we focus on the OMA of cable-stayed bridges,because they are usually long-span and flexible to have extremely low natural frequencies.It challenges experimental capability(e.g.instrumentation and budgeting)and modal identification techniques(e.g.low frequency and closely spaced modes).This paper presents a modal survey of a cable-stayed sea-crossing bridge spanning 218 m+620 m+218 m.The bridge is located in the typhoon-prone area of the northwestern Pacific Ocean.Ambient vibration data was collected for 24 h.A Bayesian fast Fourier transform modal identification method incorporating an expectation-maximization algorithm is applied for modal analysis,in which the modal parameters and associated identification uncertainties are both addressed.Nineteen modes,including 15 translational modes and four torsional modes,are identified within the frequency range of[0,2.5 Hz].

Research on Service Life Prediction Model of Concrete Structure of Sea-crossing Bridge

According to the chloride corrosion environment,service life prediction model of concrete structure of sea-crossing bridge was built using modified Fick's second law and the whole probability calculation method,which was suitable for China. Furthermore,a visual service life prediction program of concrete structure was developed by optimized Monte Carlo method. Meanwhile,Life 365 program was compared,indicating reliability of the prediction program. Finally,the validity of prediction model was verified in JinTang Bridge of Zhoushan Island Mainland Linkage Project.

Design and Pilot Programs of Marine Exposure Station of A Sea-crossing Bridge

This paper presents the Location,the structural design as well as the anti-corrosion and the pilot programs of the marine exposure station of Zhoushan Archipelago seas sea-crossing bridges. Subjected to the marine environment,the concrete structures in serve with different mixing proportions,cover thickness,additional anti-corrosion measures such as rust-preventing agent,coating,penetration crystalline waterproof material,silicone and permeable fabric were studied. Those results obtained provide important information for the maintenance of marine concrete and the structural design of sea-crossing bridges in the above sea area.

Making bridges between preclinical and clinical insights into age-related cognitive decline

With people living longer,the societal impact of age-related cognitive decline is becoming more pronounced(Crimmins,2015).Thus,it is increasingly important to comprehend the cognitive shifts linked to aging-whether they are physiological or pathological.

Dynamic Response of Sea-Crossing Rail-cum-Road Cable-Stayed Bridge Influenced by Random Wind–Wave–Undercurrent Coupling

Sea-crossing bridges are affected by random wind–wave–undercurrent coupling loads, due to the complex marine environment. The dynamic response of long-span Rail-cum-Road cable-stayed bridges is particularly severe under their influence, potentially leading to safety problems. In this paper, a fluid–structure separation solution method is implemented using Ansys–Midas co-simulation, in order to solve the above issues effectively while using less computational resources. The feasibility of the method is verified by comparing the tower top displacement response with relevant experimental data. From time and frequency domain perspectives, the displacement and acceleration responses of the sea-crossing Rail-cum-Road cable-stayed bridge influenced by wave-only, wind–wave, and wind–wave–undercurrent coupling are comparatively studied. The results indicate that the displacement and acceleration of the front bearing platform top are more significant than those of the rear bearing platform. The dominant frequency under wind–wave–undercurrent coupling is close to the natural vibration frequencies of several bridge modes,such that wind–wave–undercurrent coupling is more likely to cause a resonance effect in the bridge. Compared with the wave-only and wind–wave coupling, wind–wave–undercurrent coupling can excite bridges to produce larger displacement and acceleration responses: at the middle of the main girder span, compared with the wave-only case, the maximum displacement in the transverse bridge direction increases by 23.58% and 46.95% in the wind–wave and wind–wave–undercurrent coupling cases, respectively;at the tower top, the variation in the amplitude of the displacement and acceleration responses of wind–wave and wind–wave–undercurrent coupling are larger than those in the wave-only case, where the acceleration change amplitude of the tower top is from-0.93 to 0.86 m/s^(2) in the waveonly case, from-2.2 to 2.1 m/s^(2) under wind–wave coupling effect, and from-2.6 to 2.65 m/s^(2) under wind–wave–undercurrent coupling effect, indicating that the tower top is mainly affected by wind loads, but wave and undercurrent loads cannot be neglected.

Experimental Investigation of Wave-Current Loads on a Bridge Shuttle-Shaped Cap–Pile Foundation

To scrutinize the characteristics of wave-current loads on a bridge shuttle-shaped cap–pile foundation,a 1:125 test model was considered in a laboratory flume.The inline,transverse and vertical wave–current forces acting on the shuttle-shaped cap-pile group model were measured considering both random waves and a combination of random waves with a current.The experimental results have shown that the wave-current forces can be well correlated with the wave height,the wavelength,the current velocity,the incident direction and the water level in the marine environment.An increase in the current velocity can lead to a sharp increase in the inline and transverse wave-current forces,while the vertical wave-current force decreases.Moreover,the wave-current forces are particularly strong when a combination of high tide,strong wave and strong current is considered.

Deformation monitoring of long-span railway bridges based on SBAS-InSAR technology

The deformation monitoring of long-span railway bridges is significant to ensure the safety of human life and property.The interferometric synthetic aperture radar(In SAR)technology has the advantage of high accuracy in bridge deformation monitoring.This study monitored the deformation of the Ganjiang Super Bridge based on the small baseline subsets(SBAS)In SAR technology and Sentinel-1A data.We analyzed the deformation results combined with bridge structure,temperature,and riverbed sediment scouring.The results are as follows:(1)The Ganjiang Super Bridge area is stable overall,with deformation rates ranging from-15.6 mm/yr to 10.7 mm/yr(2)The settlement of the Ganjiang Super Bridge deck gradually increases from the bridge tower toward the main span,which conforms to the typical deformation pattern of a cable-stayed bridge.(3)The sediment scouring from the riverbed cause the serious settlement on the bridge’s east side compared with that on the west side.(4)The bridge deformation negatively correlates with temperature,with a faster settlement at a higher temperature and a slow rebound trend at a lower temperature.The study findings can provide scientific data support for the health monitoring of long-span railway bridges.

Auto-parametric resonance of a continuous-beam-bridge model under two-point periodic excitation:an experimental investigation and stability analysis

The auto-parametric resonance of a continuous-beam bridge model subjected to a two-point periodic excitation is experimentally and numerically investigated in this study.An auto-parametric resonance experiment of the test model is conducted to observe and measure the auto-parametric resonance of a continuous beam under a two-point excitation on columns.The parametric vibration equation is established for the test model using the finite-element method.The auto-parametric resonance stability of the structure is analyzed by using Newmark's method and the energy-growth exponent method.The effects of the phase difference of the two-point excitation on the stability boundaries of auto-parametric resonance are studied for the test model.Compared with the experiment,the numerical instability predictions of auto-parametric resonance are consistent with the test phenomena,and the numerical stability boundaries of auto-parametric resonance agree with the experimental ones.For a continuous beam bridge,when the ratio of multipoint excitation frequency(applied to the columns)to natural frequency of the continuous girder is approximately equal to 2,the continuous beam may undergo a strong auto-parametric resonance.Combined with the present experiment and analysis,a hypothesis of Volgograd Bridge's serpentine vibration is discussed.

Dynamic Response Impact of Vehicle Braking on Simply Supported Beam Bridges with Corrugated Steel Webs Based on Vehicle-Bridge Coupled Vibration Analysis

A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking.

Bridge Bidding via Deep Reinforcement Learning and Belief Monte Carlo Search

Contract Bridge,a four-player imperfect information game,comprises two phases:bidding and playing.While computer programs excel at playing,bidding presents a challenging aspect due to the need for information exchange with partners and interference with communication of opponents.In this work,we introduce a Bridge bidding agent that combines supervised learning,deep reinforcement learning via self-play,and a test-time search approach.Our experiments demonstrate that our agent outperforms WBridge5,a highly regarded computer Bridge software that has won multiple world championships,by a performance of 0.98 IMPs(international match points)per deal over 10000 deals,with a much cost-effective approach.The performance significantly surpasses previous state-of-the-art(0.85 IMPs per deal).Note 0.1 IMPs per deal is a significant improvement in Bridge bidding.

Recent Construction Technology Innovations and Practices for Large-Span Arch Bridges in China

Arch bridges provide significant technical and economic benefits under suitable conditions.In particular,concrete-filled steel tubular(CFST)arch bridges and steel-reinforced concrete(SRC)arch bridges are two types of arch bridges that have gained great economic competitiveness and span growth potential due to advancements in construction technology,engineering materials,and construction equipment over the past 30 years.Under the leadership of the author,two record-breaking arch bridges—that is,the Pingnan Third Bridge(a CFST arch bridge),with a span of 560 m,and the Tian’e Longtan Bridge(an SRC arch bridge),with a span of 600 m—have been built in the past five years,embodying great technological breakthroughs in the construction of these two types of arch bridges.This paper takes these two arch bridges as examples to systematically summarize the latest technological innovations and practices in the construction of CFST arch bridges and SRC arch bridges in China.The technological innovations of CFST arch bridges include cable-stayed fastening-hanging cantilevered assembly methods,new in-tube concrete materials,in-tube concrete pouring techniques,a novel thrust abutment foundation for nonrocky terrain,and measures to reduce the quantity of temporary facilities.The technological innovations of SRC arch bridges involve arch skeleton stiffness selection,the development of encasing concrete materials,encasing concrete pouring,arch rib stress mitigation,and longitudinal reinforcement optimization.To conclude,future research focuses and development directions for these two types of arch bridges are proposed.

A Rapid Crack Detection Technique Based on Attention for Intelligent M&O of Cross-Sea Bridge

Rapid and accurate segmentation of structural cracks is essential for ensuring the quality and safety of engineering projects.In practice,however,this task faces the challenge of finding a balance between detection accuracy and efficiency.To alleviate this problem,a lightweight and efficient real-time crack segmentation framework was developed.Specifically,in the network model system based on an encoding-decoding structure,the encoding network is equipped with packet convolution and attention mechanisms to capture features of different visual scales in layers,and in the decoding process,we also introduce a fusion module based on spatial attention to effectively aggregate these hierarchical features.Codecs are connected by pyramid pooling model(PPM)filtering.The results show that the crack segmentation accuracy and real-time operation capability larger than 76%and 15 fps,respectively,are validated by three publicly available datasets.These wide-ranging results highlight the potential of the model for the intelligent O&M for cross-sea bridge.

Influence of pier height on the safety of trains running on high-speed railway bridges during earthquakes

Sudden earthquakes pose a threat to the running safety of trains on high-speed railway bridges,and the stiffness of piers is one of the factors affecting the dynamic response of train-track-bridge system.In this paper,a experiment of a train running on a high-speed railway bridge is performed based on a dynamic experiment system,and the corresponding numerical model is established.The reliability of the numerical model is verified by experiments.Then,the experiment and numerical data are analyzed to reveal the pier height effects on the running safety of trains on bridges.The results show that when the pier height changes,the frequency of the bridge below the 30 m pier height changes greater;the increase of pier height causes the transverse fundamental frequency of the bridge close to that of the train,and the shaking angle and lateral displacement of the train are the largest for bridge with 50 m pier,which increases the risk of derailment;with the pier height increases from 8 m to 50 m,the derailment coefficient obtained by numerical simulations increases by 75% on average,and the spectral intensity obtained by experiments increases by 120% on average,two indicators exhibit logarithmic variation.

Seismic fragility analysis of three-tower cable-stayed bridges with different connection configurations

Seismic fragility analysis of three-tower cable-stayed bridges with three different structural systems,including rigid system(RS),floating system(FS),and passive energy dissipation system(PEDS),is conducted to study the effects of connection configurations on seismic responses and fragilities.Finite element models of bridges are established using OpenSees.A new ground motion screening method based on the statistical characteristic of the predominant period is proposed to avoid irregular behavior in the selection process of ground motions,and incremental dynamic analysis(IDA)is performed to develop components and systems fragility curves.The effects of damper failure on calculated results for PEDS are examined in terms of seismic response and fragility analysis.The results show that the bridge tower is the most affected component by different structural systems.For RS,the fragility of the middle tower is significantly higher than other components,and the bridge failure starts from the middle tower,exhibiting a characteristic of local failure.For FS and PEDS,the fragility of the edge tower is higher than the middle tower.The system fragility of RS is higher than FS and PEDS.Taking the failure of dampers into account is necessary to obtain reliable seismic capacity of cable-stayed bridges.

Alkylene-functionality in bridged and fused nitrogen-rich poly-cyclic energetic materials:Synthesis,structural diversity and energetic properties

From the standpoint of chemical structures,the organic backbones of energetic materials can be classified into aromatic rings,nonaromatic rings,and open chains.Although the category of aromatic energetic compounds exhibits several advantages in the regulation of energetic properties,the nonaromatic heterocycles,assembling nitramino explosophores with simple alkyl bridges,still have prevailed in benchmark materials.The methylene bridge plays a pivotal role in the constructions of the classic nonaromatic heterocycle-based energetic compounds,e.g.,hexahydro-1,3,5-trinitro-1,3,5-triazine(RDX)and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine(HMX),whereas ethylene bridge is the core moiety of state-of-the-art explosive 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane(CL-20).In this context,it is of great interest to employ simple and practical bridges to assemble aromatic and nonaromatic nitrogen-rich heterocycles,thereby expanding the structural diversity of energetic materials,e.g.,bridged and fused nitrogen-rich poly-heterocycles.Furthermore,alkyl-bridged poly-heterocycles highlight the potential for the open chain type of energetic materials.In this review,the development of alkyl bridges in linking nitrogen-rich heterocycles is presented,and the perspective of the newly constructed energetic backbones is summarized for the future design of advanced energetic materials.

Bridge Condition Assessment by Visual Inspection-Croatian Experience

Most decisions relating to bridge maintenance are founded on assessments that are based on visual inspections conducted by specially trained engineers,using procedures and aids defined in the management system.Visual inspection is the main tool for bridge condition assessment,and is therefore of crucial significance for planning periodic maintenance activities.Paper shall present the study aimed at harmonizing bridge assessment activities,which was conducted in early 2012 in company Hrvatske ceste-Croatian National Road Authority.Small RC bridges were chosen for this study,since visual inspection is usually only tool utilized for their assessment.Ratings obtained by inspection were analyzed using methods of mathematical statistics.The results point to weaknesses in the current assessment system,while the study itself constitutes a good basis for further improvement of management aids,manuals and procedures for bridge inspection.