Abstract： The most popularly used fin types in compact heat exchangers are the serrated fins, wavy fins, louvered fins and plain fins. Amongst these fin types the serrated fins assume lot of importance due to its enh...Abstract： The most popularly used fin types in compact heat exchangers are the serrated fins, wavy fins, louvered fins and plain fins. Amongst these fin types the serrated fins assume lot of importance due to its enhanced thermo-hydraulic performance. Thermo-hydraulic design of CHEs （Compact heat exchangers） is strongly dependent upon the predicted/measured dimensionless performance （Colburnj factor and Fanning friction vs. Reynolds number） of heat transfer surfaces. This paper describes the numerical analysis to study the heat transfer coefficient and friction factor of Serrated fins in water medium. CFD （Computational fluid dynamics） methodology has been used to develop the single phase water heat transfer coefficient and friction factor correlations for serrated fins using ANSYS Fluent 14.5. The results are compared with previous air-cooled models and experimental results of water. The water cooled CFD analysis results shows that the Prandtl number has a large effect on the Nusselt number of the serrated fin geometry. Finally, the generalized correlations are developed for serrated fins taking all geometrical parameters into account. This numerical estimation can reduce the number of tests/experiments to a minimum for similar applications.展开更多
Plowing-extruding tool was designed and plowing-extruding process was investigated.Then,a manufacturing method of integral serrated high-finned tube,plowing-extruding based on variational feed was proposed,in which pl...Plowing-extruding tool was designed and plowing-extruding process was investigated.Then,a manufacturing method of integral serrated high-finned tube,plowing-extruding based on variational feed was proposed,in which plowing-extruding tool moved forward at two different feeds,f1 and f2,in turn.In this method,overlaps that are usually avoided in practical application were utilized to manufacture high fins and average height of fins was up to 1.58 mm.The critical feed(fc) of overlaps forming and terms of high fins forming were analyzed.The main technical parameters that affect the fins height were discussed.The experimental results show that the fins height increases with extruding inclination angle and plowing-extruding depth,and the fins height increases with f1 increasing when f1 is smaller than fc,and decreases with f1 increasing if f1 is larger than fc.展开更多
文摘Abstract： The most popularly used fin types in compact heat exchangers are the serrated fins, wavy fins, louvered fins and plain fins. Amongst these fin types the serrated fins assume lot of importance due to its enhanced thermo-hydraulic performance. Thermo-hydraulic design of CHEs （Compact heat exchangers） is strongly dependent upon the predicted/measured dimensionless performance （Colburnj factor and Fanning friction vs. Reynolds number） of heat transfer surfaces. This paper describes the numerical analysis to study the heat transfer coefficient and friction factor of Serrated fins in water medium. CFD （Computational fluid dynamics） methodology has been used to develop the single phase water heat transfer coefficient and friction factor correlations for serrated fins using ANSYS Fluent 14.5. The results are compared with previous air-cooled models and experimental results of water. The water cooled CFD analysis results shows that the Prandtl number has a large effect on the Nusselt number of the serrated fin geometry. Finally, the generalized correlations are developed for serrated fins taking all geometrical parameters into account. This numerical estimation can reduce the number of tests/experiments to a minimum for similar applications.
基金Project(50605023) supported by the National Natural Science Foundation of China
文摘Plowing-extruding tool was designed and plowing-extruding process was investigated.Then,a manufacturing method of integral serrated high-finned tube,plowing-extruding based on variational feed was proposed,in which plowing-extruding tool moved forward at two different feeds,f1 and f2,in turn.In this method,overlaps that are usually avoided in practical application were utilized to manufacture high fins and average height of fins was up to 1.58 mm.The critical feed(fc) of overlaps forming and terms of high fins forming were analyzed.The main technical parameters that affect the fins height were discussed.The experimental results show that the fins height increases with extruding inclination angle and plowing-extruding depth,and the fins height increases with f1 increasing when f1 is smaller than fc,and decreases with f1 increasing if f1 is larger than fc.
