Fabricating SiC matrix with controllable Si/C ratio for C/C-SiC composites via precursor infiltration and pyrolysis is difficult to realize due to the absence of suitable precursors.Here,SiC precursors with Si-rich(Si...Fabricating SiC matrix with controllable Si/C ratio for C/C-SiC composites via precursor infiltration and pyrolysis is difficult to realize due to the absence of suitable precursors.Here,SiC precursors with Si-rich(Si/C=1.23),nearstoichiometric(Si/C=1.01),and C-rich(Si/C=0.88)pyrolyzed ceramics at 1200℃ were successfully synthesized by the novel modification of polymethysilane.The structure and ceramization of synthesized SiC precursors were studied,and C/C-SiC composites with similar Si/C ratio in SiC matrix were also fabricated.The results revealed that the defects and Young’s modulus of SiC matrix and the thermal residual stress on pyrolytic carbon coated carbon fiber were determined by the Si/C ratio.As a result,the Si/C ratio exerted significant effects on the crack deflection behavior and the mechanical properties of the composites.The composites with near-stoichiometric SiC matrix showed excellent mechanical properties because of the effective crack deflection and the moderate Young’s modulus of their SiC matrix.The flexural strength,flexural modulus,and compressive strength were 423±27 MPa,33.41±4.52 GPa,and 393±8 MPa,respectively.Meanwhile,after a heat treatment at 1600℃,the role of carbon fiber toughening was improved and accompanied by a decrease in mechanical properties for all composites,which was attributed to the increased defects in SiC matrix and the damaged interfaces by the thermal residual stress.展开更多
BACKGROUND Coronary heart disease(CHD)and heart failure(HF)are the major causes of morbidity and mortality worldwide.Early and accurate diagnoses of CHD and HF are essential for optimal management and prognosis.Howeve...BACKGROUND Coronary heart disease(CHD)and heart failure(HF)are the major causes of morbidity and mortality worldwide.Early and accurate diagnoses of CHD and HF are essential for optimal management and prognosis.However,conventional diagnostic methods such as electrocardiography,echocardiography,and cardiac biomarkers have certain limitations,such as low sensitivity,specificity,availability,and cost-effectiveness.Therefore,there is a need for simple,noninvasive,and reliable biomarkers to diagnose CHD and HF.AIM To investigate serum cystatin C(Cys-C),monocyte/high-density lipoprotein cholesterol ratio(MHR),and uric acid(UA)diagnostic values for CHD and HF.METHODS We enrolled 80 patients with suspected CHD or HF who were admitted to our hospital between July 2022 and July 2023.The patients were divided into CHD(n=20),HF(n=20),CHD+HF(n=20),and control groups(n=20).The serum levels of Cys-C,MHR,and UA were measured using immunonephelometry and an enzymatic method,respectively,and the diagnostic values for CHD and HF were evaluated using receiver operating characteristic(ROC)curve analysis.RESULTS Serum levels of Cys-C,MHR,and UA were significantly higher in the CHD,HF,and CHD+HF groups than those in the control group.The serum levels of Cys-C,MHR,and UA were significantly higher in the CHD+HF group than those in the CHD or HF group.The ROC curve analysis showed that serum Cys-C,MHR,and UA had good diagnostic performance for CHD and HF,with areas under the curve ranging from 0.78 to 0.93.The optimal cutoff values of serum Cys-C,MHR,and UA for diagnosing CHD,HF,and CHD+HF were 1.2 mg/L,0.9×10^(9),and 389μmol/L;1.4 mg/L,1.0×10^(9),and 449μmol/L;and 1.6 mg/L,1.1×10^(9),and 508μmol/L,respectively.CONCLUSION Serum Cys-C,MHR,and UA are useful biomarkers for diagnosing CHD and HF,and CHD+HF.These can provide information for decision-making and risk stratification in patients with CHD and HF.展开更多
The operation of biomass treatment devices such as gasifiers is based on the control of key parameters that play an important role in product formation. These include: temperature, excess oxygen, relative humidity and...The operation of biomass treatment devices such as gasifiers is based on the control of key parameters that play an important role in product formation. These include: temperature, excess oxygen, relative humidity and biomass composition. This work focuses on excess oxygen and temperature. Unfortunately, flue gas oxygen analyzers are expensive and not accessible to small industries. However, the equivalence ratio is linked to excess oxygen and has the advantage of not depending on biomass composition. This study therefore focuses on the design and development of a device for controlling this equivalence ratio by measuring oxygen concentration using a self-propelled Lambda probe, and a system for monitoring this equivalence ratio using an Arduino Uno 3 microcontroller. The temperature is recorded with an accuracy of ±1.5°C. For a heating time of 10 minutes, the response time to temperature change is around 3 seconds, which is sufficient for the device to function properly. This simple device is an efficient and cost-effective means of checking the equivalence ratio.展开更多
Fiber-reinforced composites possess anisotropic mechanical and heat transfer properties due to their anisotropic fibers and structure distribution.In C/Si C composites,the out-of-plane thermal conductivity has mainly ...Fiber-reinforced composites possess anisotropic mechanical and heat transfer properties due to their anisotropic fibers and structure distribution.In C/Si C composites,the out-of-plane thermal conductivity has mainly been studied,whereas the in-plane thermal conductivity has received less attention due to their limited thickness.展开更多
The performance of solid solution aging treatment on aluminum matrix composites prepared by powder metallurgy and reinforced with 6061 aluminum alloy powder as matrix;meanwhile, nano silicon carbide particles(nm Si Cp...The performance of solid solution aging treatment on aluminum matrix composites prepared by powder metallurgy and reinforced with 6061 aluminum alloy powder as matrix;meanwhile, nano silicon carbide particles(nm Si Cp), submicron silicon carbide particles(1 μm Si Cp) and Ti particles were studied. The Al/Si Cp composite powder was prepared by high-energy ball milling, and then cold-pressed, sintered, hotextruded, and then heat-treated with different solution temperatures and aging times for the extruded composites. Optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy(EDS), X-ray diffractometer(XRD) and extrusion testing were used to analyze and test the microstructure and mechanical properties of aluminum matrix composites. The results show that after the multi-stage solid solution at 530 ℃×2 h+535 ℃×2 h+540 ℃×2 h, the particles are mainly equiaxed grains and uniformly distributed. There is no reinforcement agglomeration, and the surface is dense and the insoluble phase is basically dissolved. In the matrix, the strengthening effect is good, and the hardness and compressive strength are 179.43 HV and 680.42 MPa, respectively. Under this solution process, when the aluminum matrix composites are aged at 170 ℃ for 10 h, the hardness and compressive strength can reach their peaks and increase to 195.82 HV and 721.48 MPa, respectively.展开更多
Background: Preeclampsia is reported to complicate 2% - 8% of pregnancies globally and is an important cause of maternal and perinatal morbidity and mortality. The aetiology and pathogenesis are still poorly understoo...Background: Preeclampsia is reported to complicate 2% - 8% of pregnancies globally and is an important cause of maternal and perinatal morbidity and mortality. The aetiology and pathogenesis are still poorly understood and substantial improvement has not been made in the prediction, prevention and treatment of the disease. Objective: To compare the frequency of activated protein C resistance (APC-R) in patients with pre-eclampsia to that of normotensive pregnant women and to determine the correlation between activated protein ratio (APC-ratio) and the severity of pre-eclampsia. Methodology: A cross-sectional study was carried out in 100 pre-eclamptic patients and 100 normotensive pregnant controls. The APC-ratio was determined using the modified activated partial thromboplastin time. Study participants with APC-ratio of less than 2.0 were defined as having APC-R. Data was analyzed using SPSS version 22.0. Results: Mean APC-ratio was significantly lower in pre-eclamptics (2.89 ± 1.70) compared to normotensive pregnant women (3.57 ± 1.06) (p = 0.0008) and the levels were also higher in mild (2.95 ± 1.15) compared to severe pre-eclamptics (2.62 ± 1.14). The frequency of APC-R was 26% among women with pre-eclampsia compared to 4% among normotensive controls (p = 0.000). Among 100 pre-eclamptic women 7 (21.2%) out of 33 with mild pre–eclampsia had APC-R, while 19 (28.4%) out of 67 with severe pre-eclampsia had APC-R. APC-ratio had a significant negative correlation with mean arterial blood pressure (r = −0.324;p = 0.000) and proteinuria (r = −0.379;p = 0.000) among study participants. Conclusion: The frequency of activated protein c resistance is significantly higher in pre-eclamptics compared to normotensive pregnant women and this is more pronounced in those with severe pre-eclampsia compared with those with mild disease. APC-R may therefore be used as a marker of severity in the disease.展开更多
In order to further improve the catalytic performance of zeolite catalyst for methanol to aromatics(MTA)technology, the double-tier SAPO-34/ZSM-5/quartz composite zeolite films were successfully synthesized via hydrot...In order to further improve the catalytic performance of zeolite catalyst for methanol to aromatics(MTA)technology, the double-tier SAPO-34/ZSM-5/quartz composite zeolite films were successfully synthesized via hydrothermal crystallization. The Si/Al ratio of SAPO-34 film was used as the only variable to study this material. The composite zeolite material with 0.6Si/Al ratio of SAPO-34 has the largest mesoporous specific surface area and the most suitable acid distribution. The catalytic performance for the MTA process showed that 0.6-SAPO-34/ZSM-5/quartz film has as high as 50.3% benzene-toluenexylene selectivity and 670 min lifetime. The MTA reaction is carried out through the path we designed to effectively avoid the hydrocarbon pool circulation of ZSM-5 zeolite, so as to improve the aromatics selectivity and inhibit the occurrence of deep side reactions to a great extent. The coke deposition behavior was monitored by thermogravimetric analysis and gas chromatograph/mass spectrometer, it is found that with the increase of Si/Al ratio, the active intermediates changed from low-substituted methylbenzene to high-substituted methylbenzene, which led to the rapid deactivation of the catalyst. This work provides a possibility to employ the synergy effect of composite zeolite film synthesizing anti-carbon deposition catalyst in MTA reaction.展开更多
基金supported by the National Key R&D Program of China(2021YFA0715802).
文摘Fabricating SiC matrix with controllable Si/C ratio for C/C-SiC composites via precursor infiltration and pyrolysis is difficult to realize due to the absence of suitable precursors.Here,SiC precursors with Si-rich(Si/C=1.23),nearstoichiometric(Si/C=1.01),and C-rich(Si/C=0.88)pyrolyzed ceramics at 1200℃ were successfully synthesized by the novel modification of polymethysilane.The structure and ceramization of synthesized SiC precursors were studied,and C/C-SiC composites with similar Si/C ratio in SiC matrix were also fabricated.The results revealed that the defects and Young’s modulus of SiC matrix and the thermal residual stress on pyrolytic carbon coated carbon fiber were determined by the Si/C ratio.As a result,the Si/C ratio exerted significant effects on the crack deflection behavior and the mechanical properties of the composites.The composites with near-stoichiometric SiC matrix showed excellent mechanical properties because of the effective crack deflection and the moderate Young’s modulus of their SiC matrix.The flexural strength,flexural modulus,and compressive strength were 423±27 MPa,33.41±4.52 GPa,and 393±8 MPa,respectively.Meanwhile,after a heat treatment at 1600℃,the role of carbon fiber toughening was improved and accompanied by a decrease in mechanical properties for all composites,which was attributed to the increased defects in SiC matrix and the damaged interfaces by the thermal residual stress.
文摘BACKGROUND Coronary heart disease(CHD)and heart failure(HF)are the major causes of morbidity and mortality worldwide.Early and accurate diagnoses of CHD and HF are essential for optimal management and prognosis.However,conventional diagnostic methods such as electrocardiography,echocardiography,and cardiac biomarkers have certain limitations,such as low sensitivity,specificity,availability,and cost-effectiveness.Therefore,there is a need for simple,noninvasive,and reliable biomarkers to diagnose CHD and HF.AIM To investigate serum cystatin C(Cys-C),monocyte/high-density lipoprotein cholesterol ratio(MHR),and uric acid(UA)diagnostic values for CHD and HF.METHODS We enrolled 80 patients with suspected CHD or HF who were admitted to our hospital between July 2022 and July 2023.The patients were divided into CHD(n=20),HF(n=20),CHD+HF(n=20),and control groups(n=20).The serum levels of Cys-C,MHR,and UA were measured using immunonephelometry and an enzymatic method,respectively,and the diagnostic values for CHD and HF were evaluated using receiver operating characteristic(ROC)curve analysis.RESULTS Serum levels of Cys-C,MHR,and UA were significantly higher in the CHD,HF,and CHD+HF groups than those in the control group.The serum levels of Cys-C,MHR,and UA were significantly higher in the CHD+HF group than those in the CHD or HF group.The ROC curve analysis showed that serum Cys-C,MHR,and UA had good diagnostic performance for CHD and HF,with areas under the curve ranging from 0.78 to 0.93.The optimal cutoff values of serum Cys-C,MHR,and UA for diagnosing CHD,HF,and CHD+HF were 1.2 mg/L,0.9×10^(9),and 389μmol/L;1.4 mg/L,1.0×10^(9),and 449μmol/L;and 1.6 mg/L,1.1×10^(9),and 508μmol/L,respectively.CONCLUSION Serum Cys-C,MHR,and UA are useful biomarkers for diagnosing CHD and HF,and CHD+HF.These can provide information for decision-making and risk stratification in patients with CHD and HF.
文摘The operation of biomass treatment devices such as gasifiers is based on the control of key parameters that play an important role in product formation. These include: temperature, excess oxygen, relative humidity and biomass composition. This work focuses on excess oxygen and temperature. Unfortunately, flue gas oxygen analyzers are expensive and not accessible to small industries. However, the equivalence ratio is linked to excess oxygen and has the advantage of not depending on biomass composition. This study therefore focuses on the design and development of a device for controlling this equivalence ratio by measuring oxygen concentration using a self-propelled Lambda probe, and a system for monitoring this equivalence ratio using an Arduino Uno 3 microcontroller. The temperature is recorded with an accuracy of ±1.5°C. For a heating time of 10 minutes, the response time to temperature change is around 3 seconds, which is sufficient for the device to function properly. This simple device is an efficient and cost-effective means of checking the equivalence ratio.
基金supported by the National Natural Science Foundation of China(Grant Nos.52276086 and 52130604)the Basic Research Program of China(Grant No.514010303-102)the K.C.Wong Education Foundation。
文摘Fiber-reinforced composites possess anisotropic mechanical and heat transfer properties due to their anisotropic fibers and structure distribution.In C/Si C composites,the out-of-plane thermal conductivity has mainly been studied,whereas the in-plane thermal conductivity has received less attention due to their limited thickness.
基金the Key Projects of Equipment Pre-research Foundation of the Ministry of Equipment Development of the Central Military Commission of China (No.6140922010201)the Key R&D Plan of Zhenjiang in 2018(No.GY2018021)。
文摘The performance of solid solution aging treatment on aluminum matrix composites prepared by powder metallurgy and reinforced with 6061 aluminum alloy powder as matrix;meanwhile, nano silicon carbide particles(nm Si Cp), submicron silicon carbide particles(1 μm Si Cp) and Ti particles were studied. The Al/Si Cp composite powder was prepared by high-energy ball milling, and then cold-pressed, sintered, hotextruded, and then heat-treated with different solution temperatures and aging times for the extruded composites. Optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy(EDS), X-ray diffractometer(XRD) and extrusion testing were used to analyze and test the microstructure and mechanical properties of aluminum matrix composites. The results show that after the multi-stage solid solution at 530 ℃×2 h+535 ℃×2 h+540 ℃×2 h, the particles are mainly equiaxed grains and uniformly distributed. There is no reinforcement agglomeration, and the surface is dense and the insoluble phase is basically dissolved. In the matrix, the strengthening effect is good, and the hardness and compressive strength are 179.43 HV and 680.42 MPa, respectively. Under this solution process, when the aluminum matrix composites are aged at 170 ℃ for 10 h, the hardness and compressive strength can reach their peaks and increase to 195.82 HV and 721.48 MPa, respectively.
文摘Background: Preeclampsia is reported to complicate 2% - 8% of pregnancies globally and is an important cause of maternal and perinatal morbidity and mortality. The aetiology and pathogenesis are still poorly understood and substantial improvement has not been made in the prediction, prevention and treatment of the disease. Objective: To compare the frequency of activated protein C resistance (APC-R) in patients with pre-eclampsia to that of normotensive pregnant women and to determine the correlation between activated protein ratio (APC-ratio) and the severity of pre-eclampsia. Methodology: A cross-sectional study was carried out in 100 pre-eclamptic patients and 100 normotensive pregnant controls. The APC-ratio was determined using the modified activated partial thromboplastin time. Study participants with APC-ratio of less than 2.0 were defined as having APC-R. Data was analyzed using SPSS version 22.0. Results: Mean APC-ratio was significantly lower in pre-eclamptics (2.89 ± 1.70) compared to normotensive pregnant women (3.57 ± 1.06) (p = 0.0008) and the levels were also higher in mild (2.95 ± 1.15) compared to severe pre-eclamptics (2.62 ± 1.14). The frequency of APC-R was 26% among women with pre-eclampsia compared to 4% among normotensive controls (p = 0.000). Among 100 pre-eclamptic women 7 (21.2%) out of 33 with mild pre–eclampsia had APC-R, while 19 (28.4%) out of 67 with severe pre-eclampsia had APC-R. APC-ratio had a significant negative correlation with mean arterial blood pressure (r = −0.324;p = 0.000) and proteinuria (r = −0.379;p = 0.000) among study participants. Conclusion: The frequency of activated protein c resistance is significantly higher in pre-eclamptics compared to normotensive pregnant women and this is more pronounced in those with severe pre-eclampsia compared with those with mild disease. APC-R may therefore be used as a marker of severity in the disease.
基金supported by the National Natural Science Foundation of China (51974312, 51974308)the National Key Research & Development Program of China (2019YFE0100100)。
文摘In order to further improve the catalytic performance of zeolite catalyst for methanol to aromatics(MTA)technology, the double-tier SAPO-34/ZSM-5/quartz composite zeolite films were successfully synthesized via hydrothermal crystallization. The Si/Al ratio of SAPO-34 film was used as the only variable to study this material. The composite zeolite material with 0.6Si/Al ratio of SAPO-34 has the largest mesoporous specific surface area and the most suitable acid distribution. The catalytic performance for the MTA process showed that 0.6-SAPO-34/ZSM-5/quartz film has as high as 50.3% benzene-toluenexylene selectivity and 670 min lifetime. The MTA reaction is carried out through the path we designed to effectively avoid the hydrocarbon pool circulation of ZSM-5 zeolite, so as to improve the aromatics selectivity and inhibit the occurrence of deep side reactions to a great extent. The coke deposition behavior was monitored by thermogravimetric analysis and gas chromatograph/mass spectrometer, it is found that with the increase of Si/Al ratio, the active intermediates changed from low-substituted methylbenzene to high-substituted methylbenzene, which led to the rapid deactivation of the catalyst. This work provides a possibility to employ the synergy effect of composite zeolite film synthesizing anti-carbon deposition catalyst in MTA reaction.
