The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magn...The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.展开更多
SiC particles reinforced AZ91 Mg matrix composites （SiCp/AZ91） with SiC volume fractions of 5%, 10% and 15% were fabricated by stir casting. After T4 treatment, these composites were extruded at 350 °C with an ...SiC particles reinforced AZ91 Mg matrix composites （SiCp/AZ91） with SiC volume fractions of 5%, 10% and 15% were fabricated by stir casting. After T4 treatment, these composites were extruded at 350 °C with an extrusion ratio of 12：1. In the as-cast composite, particles segregated at a microscopic scale within the intergranular regions. Hot extrusion almost eliminated this particle aggregation and improved the particle distribution of the composites. In addition, extrusion refined the grains of matrix. The results show that hot extrusion significantly improves the mechanical properties of the composites. In the as-extruded composite, with the increase of SiCp contents, the grain size of the extruded composites decreases, the strength and elastic modulus increase but the elongation decreases.展开更多
In order to improve the interface bonding of SiCp/AZ61 composites prepared by powder metallurgy followed by hot extrusion, the electroless plating of Ni-P coating on SiCp was carried out. The influence of Ni coating o...In order to improve the interface bonding of SiCp/AZ61 composites prepared by powder metallurgy followed by hot extrusion, the electroless plating of Ni-P coating on SiCp was carried out. The influence of Ni coating on microstructure and mechanical properties of the composites was analyzed. The results show that SiC particles distribute more uniformly in the composites after surface Ni plating and there are fewer defects in Ni-coated composite. The Ni coating reacts with the magnesium matrix forming the Mg2Ni interfacial compound layer during the sintering process. The relative density of the composite increases from 97.9% to 98.4% compared with uncoated one and the hardness of the Ni-coated composite increases more rapidly as the volume fraction of SiCp increases. The tensile test results show that the tensile strength increases from 320 to 336 MPa when the volume friction of SiC particle is 9% and the Ni-coated composites have larger elongation, indicating that Ni coating improves the interfacial bonding strength and the performance of the composites. In addition, the fracture properties of SiCp/AZ61 composites were analyzed.展开更多
SiC nanoparticles reinforced magnesium matrix composites were fabricated by ultrasonic method.The AZ91 alloy and SiC nanoparticles with the average diameter of 50 nm were used as the matrix alloy and the reinforcement...SiC nanoparticles reinforced magnesium matrix composites were fabricated by ultrasonic method.The AZ91 alloy and SiC nanoparticles with the average diameter of 50 nm were used as the matrix alloy and the reinforcement,respectively.The addition of nanoparticles was 0.1%,0.3%,and 0.5%(mass fraction) of the composites.The results of microstructural evaluation and mechanical properties indicate that the nanoparticles can be dispersed into magnesium alloys efficiently and uniformly with the aid of ultrasonic vibration.As compared with the matrix alloys,the grains of composites were refined and the mechanical properties of composites were improved significantly.The SEM and DSC analyses show that the SiC nanoparticles can act as the heterogeneous nucleation of α-Mg.Also,the strengthening mechanism responsible for the composites reinforced with SiC nanoparticles was discussed.展开更多
Mg-based alloys are potential candidate materials for a fabrication of lightweight boron carbide based composites through a reactive melt infiltration approach. In this paper, the effect of a mechanical purification o...Mg-based alloys are potential candidate materials for a fabrication of lightweight boron carbide based composites through a reactive melt infiltration approach. In this paper, the effect of a mechanical purification of molten AZ91 alloy’s surface on its wettability with polycrystalline B_(4)C is experimentally evaluated for the first time. For this purpose, sessile drop experiments were performed under the same operating conditions(700℃/5 min;Ar atmosphere), by using both the classical contact heating(CH) and the improved capillary purification(CP) procedure. It was found that the evolution of contact angle values was strongly influenced by the applied procedure. In particular, by using the classical CH procedure, the presence of a native oxide layer on the metal surface hinders the observations of melting process, resulting in a misleading conclusion that the system is non-wettable. Contrarily, during the wetting test performed by applying the CP procedure, the surface oxide layer was mechanically removed by squeezing the molten AZ91 alloy through a capillary. Accordingly, the oxide-free AZ91 drop with a regular and spherical shape was successfully obtained and dispensed on the B_(4)C substrate. A reliable contact angle value of θ =83° was measured at the AZ91/B_(4)C triple line at 700 ℃, which in turn proves that B_(4)C is wetted by the liquid AZ91 alloy. In contradiction to the literature, these good wetting conditions were assisted by a non-reactive wetting mechanism occurring at the AZ91/B_(4)C interface. To succeed in the fabrication of AZ91/B_(4)C composites by liquid metal infiltration, such experimental observations make it reasonable to expect a spontaneous infiltration process exclusively driven by capillarity, which in turn increases the efficiency of the process by the absence of reaction products that could be a potentially detrimental factor.展开更多
In-situ TiB_2/AZ31 composites were prepared by utilizing the SHS reaction of Al-Ti-B system in the molten magnesium,and the effects of external physical fields on the dispersion of TiB_2 particles were investigated.Th...In-situ TiB_2/AZ31 composites were prepared by utilizing the SHS reaction of Al-Ti-B system in the molten magnesium,and the effects of external physical fields on the dispersion of TiB_2 particles were investigated.The results show that high-energy ultrasonic vibration could effectively break up the particle clusters and make the TiB2 particles uniformly distributed in the melt of TiB_2/AZ31 composites.The compound field(high-energy ultrasonic field coupling with electromagnetic field)could not only distribute the TiB_2 particles into the matrix uniformly,but also make the grains of α-Mg free and uniform further than the ultrasonic field solo.The average grain size of as-cast TiB_2/AZ31 composites was reduced from 173μm to 94μm.展开更多
基金National Natllral S(tience l.'oundation of China (No. 59631080).
文摘The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.
基金Projects (51101043, 50801017, 51001036) supported by the National Natural Science Foundation of ChinaProject (HIT.NSRIF.201130) supported by the Fundamental Research Funds for the Central Universities, China
文摘SiC particles reinforced AZ91 Mg matrix composites （SiCp/AZ91） with SiC volume fractions of 5%, 10% and 15% were fabricated by stir casting. After T4 treatment, these composites were extruded at 350 °C with an extrusion ratio of 12：1. In the as-cast composite, particles segregated at a microscopic scale within the intergranular regions. Hot extrusion almost eliminated this particle aggregation and improved the particle distribution of the composites. In addition, extrusion refined the grains of matrix. The results show that hot extrusion significantly improves the mechanical properties of the composites. In the as-extruded composite, with the increase of SiCp contents, the grain size of the extruded composites decreases, the strength and elastic modulus increase but the elongation decreases.
基金Project(CXZZ20140506150310438)support by the Science and Technology Program of Shenzhen,ChinaProject(2017GK2261)supported by the Science and Technology Program of Hunan,ChinaProject(2017zzts111)supported by the Fundamental Research Funds for the Central Universities of Central South University,China
文摘In order to improve the interface bonding of SiCp/AZ61 composites prepared by powder metallurgy followed by hot extrusion, the electroless plating of Ni-P coating on SiCp was carried out. The influence of Ni coating on microstructure and mechanical properties of the composites was analyzed. The results show that SiC particles distribute more uniformly in the composites after surface Ni plating and there are fewer defects in Ni-coated composite. The Ni coating reacts with the magnesium matrix forming the Mg2Ni interfacial compound layer during the sintering process. The relative density of the composite increases from 97.9% to 98.4% compared with uncoated one and the hardness of the Ni-coated composite increases more rapidly as the volume fraction of SiCp increases. The tensile test results show that the tensile strength increases from 320 to 336 MPa when the volume friction of SiC particle is 9% and the Ni-coated composites have larger elongation, indicating that Ni coating improves the interfacial bonding strength and the performance of the composites. In addition, the fracture properties of SiCp/AZ61 composites were analyzed.
基金Project(2007CB613706) supported by the National Basic Research Program of ChinaProject(00900054R4001) supported by Innovation Project for Talents of BJUTProject(00900054K4004) supported by the Science Foundation for Youths of BJUT
文摘SiC nanoparticles reinforced magnesium matrix composites were fabricated by ultrasonic method.The AZ91 alloy and SiC nanoparticles with the average diameter of 50 nm were used as the matrix alloy and the reinforcement,respectively.The addition of nanoparticles was 0.1%,0.3%,and 0.5%(mass fraction) of the composites.The results of microstructural evaluation and mechanical properties indicate that the nanoparticles can be dispersed into magnesium alloys efficiently and uniformly with the aid of ultrasonic vibration.As compared with the matrix alloys,the grains of composites were refined and the mechanical properties of composites were improved significantly.The SEM and DSC analyses show that the SiC nanoparticles can act as the heterogeneous nucleation of α-Mg.Also,the strengthening mechanism responsible for the composites reinforced with SiC nanoparticles was discussed.
基金the financial support given by the National Science Centre (NCN) in Poland,under the project MINIATURA 2, No. 2018/02/X/ST8/03044 in2019–2020。
文摘Mg-based alloys are potential candidate materials for a fabrication of lightweight boron carbide based composites through a reactive melt infiltration approach. In this paper, the effect of a mechanical purification of molten AZ91 alloy’s surface on its wettability with polycrystalline B_(4)C is experimentally evaluated for the first time. For this purpose, sessile drop experiments were performed under the same operating conditions(700℃/5 min;Ar atmosphere), by using both the classical contact heating(CH) and the improved capillary purification(CP) procedure. It was found that the evolution of contact angle values was strongly influenced by the applied procedure. In particular, by using the classical CH procedure, the presence of a native oxide layer on the metal surface hinders the observations of melting process, resulting in a misleading conclusion that the system is non-wettable. Contrarily, during the wetting test performed by applying the CP procedure, the surface oxide layer was mechanically removed by squeezing the molten AZ91 alloy through a capillary. Accordingly, the oxide-free AZ91 drop with a regular and spherical shape was successfully obtained and dispensed on the B_(4)C substrate. A reliable contact angle value of θ =83° was measured at the AZ91/B_(4)C triple line at 700 ℃, which in turn proves that B_(4)C is wetted by the liquid AZ91 alloy. In contradiction to the literature, these good wetting conditions were assisted by a non-reactive wetting mechanism occurring at the AZ91/B_(4)C interface. To succeed in the fabrication of AZ91/B_(4)C composites by liquid metal infiltration, such experimental observations make it reasonable to expect a spontaneous infiltration process exclusively driven by capillarity, which in turn increases the efficiency of the process by the absence of reaction products that could be a potentially detrimental factor.
基金Item Sponsored by National High Technology Research and Development Program of China[No.2009AA03Z525]Aviation Science Foundation of China[No.20095263005]
文摘In-situ TiB_2/AZ31 composites were prepared by utilizing the SHS reaction of Al-Ti-B system in the molten magnesium,and the effects of external physical fields on the dispersion of TiB_2 particles were investigated.The results show that high-energy ultrasonic vibration could effectively break up the particle clusters and make the TiB2 particles uniformly distributed in the melt of TiB_2/AZ31 composites.The compound field(high-energy ultrasonic field coupling with electromagnetic field)could not only distribute the TiB_2 particles into the matrix uniformly,but also make the grains of α-Mg free and uniform further than the ultrasonic field solo.The average grain size of as-cast TiB_2/AZ31 composites was reduced from 173μm to 94μm.
基金National Natural Science Foundation of China(51201006,51071057,51251201112,5140114)Natural Science Foundation of Shanxi(201601D011034,2015021067)+1 种基金Projects of International Cooperation in Shanxi(2014081002)the"111 Project"(B12012)
