Investigation on Material Response of 55% SiCp/Al Composites Induced by Pulsed Laser

Silicon carbide particle reinforced aluminum matrix composites(SiCp/Al composites)are widely used in aviation,aerospace and electronic package.However,low machining efficiency,severe tool wear and poor surface quality are severe during the machining of SiCp/Al composites.Laser-induced oxidation is capable to improve the machinability of SiCp/Al composites.The material response of 55%(volume fraction)SiCp/Al composites induced by a nanosecond pulsed laser is studied.A metamorphic layer which is composed of an oxide layer and sub-layer is produced.The effects of reaction surrounding and laser average power on the microstructure and thickness of the oxide layer and sub-layer are investigated.Experimental results show that:A thicker oxide layer and a sub-layer are formed in an oxygen-rich atmosphere.The oxides are mainly composed of 2Al2O3·SiO2(mullite).A positive correlation between the laser average power and thicknesses of oxide layers and sub-layers is found.A loose oxide layer of 138μm and a sub-layer of 21μm are formed at the laser average power of 6 W,laser scanning pitch of 10μm,and laser scanning speed of 1 mm/s under an oxygen-rich atmosphere.The high efficient machining of Si Cp/Al composites can be realized by laser-induced oxidation.

Experimental Study of Machinability in Millgrinding of SiCp/Al Composites

An attempt was made to investigate the machinability of Si Cp/Al composites based on the experimental study using mill-grinding processing method. The experiments were carried out on a high-speed CNC machining center using integrated abrasive cutting tool. The effects of combined machining parameters, e g, cutting speed（vs）, feed rate（vf）, and depth of cut（ap）, with the same change of material removal rate（MRR） on the mill-grinding force and surface roughness（Ra） were investigated. The formation mechanism of typical machined surface defects was analyzed by SEM. The experimental results reveal that with the same change of material removal rate, lower mill-grinding force values can be gained by increasing depth of cut and feed rate simultaneously at higher cutting speed. With the same change of MRR value, lower surface roughness values can be gained by increasing the feed rate at higher cutting speed, rather than just increasing the depth of cut, or increasing the feed rate and depth of cut simultaneously. The machined surface of Si Cp/Al composites reveals typical defects which can influence surface integrity.

Particle Removal Mechanism of High Volume Fraction SiCp/Al Composites by Single Diamond Grit Tool

Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.

Effect of a Slight Interfacial Reaction on Mechanical Properties of SiCp/Al Composites

A slight interfacial reaction in squeeze-cast SiCp/6061AI composites has been studied. It is found that this kind of reaction has a particular effect on the mechanical properties of the composites. The results of fie-cure tests show that this reaction in the composites obviously increases the elastic properties, but is not beneficial to the fracture strength and ductility.This phenomenon can be interpreted in terms of two different micromechanisms which have been analyzed using TEM and HREM observations, acoustic emission (AE) technique and SEM fractography. In addition, a new method of SiC surface modification which can control the interface state is initially presented.

Effect of Na3AlF6 Addition and Surface Modification of SiCp on the Microstructure and Mechanical Properties of SiCp/Al Composites

Al-matrix composites reinforced with 56.5 vol% SiC were prepared by powder metallurgy with different amounts of additives and surface modifications of SiCp. The crystalline phase, morphology, elements on the surface of SiCp and the interface between SiCp and Al were characterized by XRD, SEM, EDS and EPMA. The results show that it is favorable for the reaction between TiO2-C on the surface of SiCp and Al at the SiCp-Al interface at 1 050 ℃. Besides, the process of Na3 AlF6 melting, dissolving and then contacting with Al2 O3 formed the NaF-AlF3-Al2 O3 system, which generated OAlF2-, promoting the dessolution of Al2 O3 film on the surface of Al powder. Na3 AlF6 meets the needs of chemical reaction in TiO2-C-Al system at the SiCpAl interface in the way of offering more molten Al. After 0.75 wt% Na3 AlF6 was added into raw materials, the whole TiO2-C film and most SiO2 film were destroyed and the interfacial bonding between SiCp and Al was keeping good, in which no obvious void and crack were observed. Meanwhile, no brittle Al4 C3 phase formed in the system. At this time, the flexure strength and density of samples presented optimal values, reaching up to 106.5 MPa and 90.77% respectively.

Spark Effect on the Densification of SiCp/Al Composites by SPS

SiCp/ Al composites containing high volume fraction of SiC particles were fabricated by spark plasma sintering （SPS）. and their thermophysical properties, such as thermal conductivity （TC） and co.lent of thermal expansion （CTE）, were characterized. The electric field in the vacuum column was calculated and the generation condition of the spark was analyzed. Spark can be generated by a low current if the cavity in the green body is large enough. A high relative density of the composites was successfully achieved through the optimization of sintering parameters. The measured TCs of the SiCp/ Al composites fabricated by SPS are higher than 195 W/m ·K.

Reactive Diffusion Bonding of SiCp/Al Composites by Insert Powder Layers with Eutectic Composition

Mixed Al-Si and Al-Cu powders were investigated as insert layers to reactive diffusion bond SiCp/6063 metal matrix composite （MMC）. The results show that SiCp/6063 MMC joints bonded by the insert layers of the mixed Al-Si and Al-Cu powders have a dense joining layer of high quality. The mass transfer between the bonded materials and insert layers during bonding leads to the hypoeutectic microstructure of the joining layers bonded by both the mixed Al-Si and Al-Cu powders with eutectic composition. At fixed bonding time （temperature）, the shear strength of the joints by both insert layers of the mixed Al-Si and Al-Cu powders increases with increasing the bonding temperature （time）, but get maxima at bonding temperature 600℃ （time 90 min）.

Reactive diffusion bonding of SiCp/Al composites by insert layers of mixed Al-Si and Al-Si-SiC powders

Mixed Al-Si and Al-Si-SiC powders were employed as insert layers to reactive diffusion bond SiCp/6063 MMC （metal matrix composites）. The results show that SiCp/6063 MMC joints bonded by the insert layer of the mixed Al-Si powder have a dense joining layer with a typical hypoeutectic microstructtn＇e. Using the mixed Al-Si-SiC powder as the insert layer, SiCp/6063 MMC can be reactive diffusion bonded by a composite joint. Because of the SiC segregation, however, there are a number of porous zones in the joining layer, which results in the bad shear strength of the joints reactive diffusion bonded by the insert layer of the mixed A1-Si- SiC powder, even lower than that of the joints reactive diffusion bonded by the insert layer of the mixed Al-Si powder. Ti and Mg added in the insert layers obviously improve the strength of the joints reactive diffusion bonded by the insert layer of the mixed Al- Si-SiC powder, especially, Mg has a more obvious effect.

Pressureless infiltration processing and thermal properties of SiCp/Al composites with high SiC particle content

SiCp/1060Al, SiCp/ZL101,SiCp/ZL102 composites with SiCp volume fraction of 55% were fabricated by pressureless infiltration. The microstructure was examined and thermal properties were characterized for SiCp/Al composites. The results show that the composites are dense and macroscopically homogeneous. With the increase of temperature, the mean linear coefficient of thermal expansion(CTE) at 25-200℃of the composites increases and ranges from 7.23×10-6 to 10.4×10-6K-1, but thermal conductivity declines gradually at the same time. With the increase of Si content in the Al matrix, CTE of the composites declines and thermal conductivity also declines but not linearly, when Si content is up to 7%, the average thermal conductivity is 140.4 W/(m·K), which is close to that of the SiCp/1060Al composite (144.6 W/(m·K)). While Si content is 11.7%, the average thermal conductivity declines markedly to 87.74 W/(m·K). The annealing treatment is better than the solution aging treatment in reducing CTE and improving thermal conductivity of the composites. Compared with conventional thermal management materials, SiCp/Al composites are potential candidate materials for advanced electronic packaging due to their tailorable thermo-physical properties.

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

In recent years,the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys.However,the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites,particularly at elevated temperat-ures,remains an understudied area.In this study,Al-Si-Cu-Mg-Ni/20wt%SiC particles(SiCp)composites with varying Ni contents were prepared by using a semisolid stir casting method.The effect of Ni content on the dry sliding wear behavior of the prepared compos-ites was investigated through sliding tests at 25 and 350℃.Results indicated that theθ-Al_(2)Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt%to 3wt%.This change was accompanied by the formation and increase inδ-Al_(3)CuNi andε-Al_(3)Ni phases in microstructures.The hardness and ultimate tensile strength of the as-cast composites improved,and the wear rates of the composites decreased from 5.29×10^(−4)to 1.94×10^(−4)mm^(3)/(N∙m)at 25℃and from 20.2×10^(−4)to 7×10^(−4)mm^(3)/(N∙m)at 350℃with the increase in Ni content from 0wt%to 2wt%.The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites.However,the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of theε-Al_(3)Ni phase.Abrasive wear,delamination wear,and oxidation wear were the predominant wear mechanisms of the investigated composites at 25℃,whereas delamination wear and oxid-ation wear were dominant during sliding at 350℃.

Damping properties and mechanism of aluminum matrix composites reinforced with glass cenospheres

The damping properties were improved by preparing Al matrix composites reinforced with glass cenospheres through the pressure infiltration method.Transmission electron microscopy and scanning electron microscopy were employed to characterize the microstructure of the composites.The low-frequency damping properties were examined by using a dynamic mechanical thermal analyzer,aiming at exploring the changing trend of damping capacity with strain,temperature,and frequency.The findings demonstrated that the damping value rose as temperature and strain increased,with a maximum value of 0.15.Additionally,the damping value decreased when the frequency increased.Dislocation damping under strain and interfacial damping under temperature served as the two primary damping mechanisms.The increase in the density of dislocation strong pinning points following heat treatment reduced the damping value,which was attributed to the heat treatment enhancement of the interfacial bonding force of the composites.

Microstructure,interfacial reaction behavior,and mechanical properties of Ti_3AlC_(2)reinforced Al6061 composites

The interfacial reaction behavior of Al and Ti_3AlC_(2)at different pouring temperatures and its effect on the microstructure and mechanical properties of the composites were investigated.The results show that the addition of3.0 wt.%Ti_3AlC_(2)refines the average grain size ofα(Al)in the composite by 50.1%compared to Al6061 alloy.Morphological analyses indicate that an in-situ Al_(3Ti)transition layer of-180 nm in thickness is generated around the edge of Ti_3AlC_(2)at 720℃,forming a well-bonded Al-Al_(3Ti)interface.At this processing temperature,the ultimate tensile strength of A16061-3.0 wt.%Ti_3AlC_(2)composite is 199.2 MPa,an improvement of 41.5%over the Al6061 matrix.Mechanism analyses further elucidate that 720℃is favourable for forming the nano-sized transition layer at the Ti_3AlC_(2)edges.And,the thermal mismatch strengthening plays a dominant role in this state,with a strengthening contribution of about 74.8%.

Microstructure evolution,mechanical properties and fracture behavior of Al-xSi/AZ91D bimetallic composites prepared by a compound casting

In this paper,the effect of the Si content on microstructure evolution,mechanical properties,and fracture behavior of the Al-xSi/AZ91D bimetallic composites prepared by compound casting was investigated systematically.The obtained results showed that all the Al-xSi/AZ91D bimetallic composites had a metallurgical reaction layer(MRL),whose thickness increased with increasing Si content for the hypoeutectic Al-Si/AZ91D composites,while the hypereutectic Al-Si/AZ91D composites were opposite.The MRL included eutectic layer(E layer),intermetallic compound layer(IMC layer)and transition region layer(T layer).In the IMC layer,the hypereutectic Al-Si/AZ91D composites contained some Si solid solution and flocculent Mg_(2)Si+Al-Mg IMCs phases not presented in the hypoeutectic Al-Si/AZ91D composites.Besides,increasing Si content,the thickness proportion of the T layer increased,forming an inconsistent preferred orientation of the MRL.The shear strengths of the Al-xSi/AZ91D bimetallic composites enhanced with increasing Si content,and the Al-15Si/AZ91D composite obtained a maximum shear strength of 58.6 MPa,which was 73.4% higher than the Al-6Si/AZ91D composite.The fractures of the Al-xSi/AZ91D bimetallic composites transformed from the T layer into the E layer with the increase of the Si content.The improvement of the shear strength of the Al-xSi/AZ91D bimetallic composites was attributed to the synergistic action of the Mg_(2)Si particle reinforcement,the reduction of oxidizing inclusions and the ratio of Al-Mg IMCs as well as the orientation change of the MRL.

超声振动辅助切削SiCp/Al复合材料的加工机理及试验

切削加工过程中材料损伤形式对加工表面质量会产生较大影响,现有仿真分析难以模拟真实颗粒失效行为,通过建立二维微观多相有限元模型能够深入了解材料损伤与表面质量的关系。基于常规切削(Conventional cutting,CC)与超声振动辅助切削(Ultrasonic vibration-assisted cutting,UVAC)两种加工方式,通过有限元仿真软件Abaqus对20%SiCp/Al复合材料的切削过程进行仿真模拟,阐释加工过程中刀具与工件的相互作用机理,并在同一参数下验证有限元仿真的准确性。通过设计单因素试验,对比两种加工方式及不同加工参数对切削力和表面粗糙度的影响规律,得出最佳加工参数组合,并对最佳加工参数下表面形貌进行分析。模拟和试验结果表明,SiC颗粒断裂、颗粒耕犁、颗粒拔出以及Al基体撕裂是影响SiCp/Al复合材料加工质量的主要原因,刀具与颗粒不同的相对作用位置会产生不同的损伤形式。与常规切削相比,施加超声振动后可以有效抑制颗粒失效和基体损伤,使加工中的平均切削力(主切削力)降低33%,工件已加工表面粗糙度值最大减小量为531 nm,显著提高了表面质量。所建立的二维微观多相有限元模型,能够有效模拟铝基复合材料的加工缺陷和裂纹损伤问题,对提高难加工材料的高质量表面制备有重要借鉴意义。

超声振动辅助车削SiCp/Al切屑形成机理及表面粗糙度研究

目的研究切屑形成机理对加工过程的影响。方法超声振动辅助车削技术通过刀具振动的拟间歇切削特征控制切屑尺寸和切屑形态,从而提高了加工表面质量。针对SiCp/Al复合材料的切屑形成机理,探究常规车削和超声振动辅助车削的切屑形成过程。研究了颗粒分布对第一变形区变形阶段的影响,以及不同加工方式下切削参数对切屑形态的影响。最后,描述了切屑自由表面和刀-屑接触界面的颗粒损伤形式,以直观地描述常规车削与超声振动辅助车削SiCp/Al复合材料加工中切屑的形成过程。结果通过测试加工后工件表面形貌发现超声振动辅助车削的切屑更加连续、切屑尺寸较小的加工表面粗糙度更小,常规车削的表面粗糙度为0.805μm,超声振动辅助车削的表面粗糙度为0.404μm,超声振动辅助车削比常规车削的表面粗糙度降低了49.8%。结论与常规车削相比,超声振动辅助车削有利于减小切屑厚度。超声振动辅助车削得到的切屑更加连续,避免了切屑碎裂,促进了切屑的顺利排出。通过对切屑形态进行研究,选择最优切削参数可以有效提高工件表面质量。

纵扭超声辅助铣削SiCp/Al复合材料表面质量研究

高体积分数SiCp/Al复合材料具有高比强度、高比模数和良好的耐磨性等优异性能。然而,它们的高硬度和脆性会导致精密制造过程中应力分布更为复杂,这会使材料中产生过大的力和过多的热,从而影响加工精度和工件耐久极限寿命。目的通过分析切削过程中颗粒的去除机理和表面缺陷类型,利用纵扭超声辅助铣削(longitudinal-torsional ultrasonic assisted milling,LTUAM)技术,改善高体积分数SiCp/Al复合材料的加工表面质量。方法利用ABAQUS和PYTHON软件,建立考虑颗粒断裂过程的两相随机分布颗粒SiCp/Al复合材料模型,并采用Johnson-Cook模型和Brittle Cracking模型对SiCp/Al复合材料纵扭超声辅助铣削过程进行有限元模拟仿真。针对不同加工参数,进行SiCp/Al复合材料纵扭超声辅助铣削和常规铣削(conventional milling,CM)试验,评估有限元仿真模拟与试验结果的一致性。结果模拟结果表明,损伤和裂纹主要产生在SiC颗粒(SiCp)中上部的切削线上,凹坑缺陷主要产生在颗粒下部的切削线上。试验结果显示,表面缺陷的类型主要包括颗粒的损伤和拔出、颗粒的损伤和断裂形成凹坑、未损伤的颗粒形成凸起、破损颗粒与刀具在已加工表面上挤压摩擦形成犁沟、铝基体涂覆、表面微裂纹和表面空穴等,并且当加工速度120 m/min,超声振幅3μm时,最大裂纹深度最小,表面缺陷最小,表面质量最好。结论对比有限元仿真结果与试验结果发现,二者的表面质量变化趋势基本具有一致性。纵扭超声辅助铣削技术的应用对提高SiCp/Al复合材料的表面质量有较好效果。

Machining Characteristics in Cryogenic Grinding of SiCp/Al Composites

In this study, liquid nitrogen was applied to grind SiCp/Al composites with high volume fraction and large SiC particle at different levels of cutting conditions, and the effects of grinding depth and speed on grinding force, surface morphology, and surface roughness were investigated. At the same time, the effect of cryogenic cooling was also compared with that of conventional wet grinding. The experimental results indicated that cryogenic cooling is effective in enhancing supporting function of Al matrix to the SiC particles and improving surface quality. Additionally, the brittle fracture of SiC particles was suppressed and some ductile streaks on SiC particle could be observed.

SiCp/Al-Si基复合材料界面结构调控及强化机制的研究进展

SiCp/Al-Si基复合材料具有高的比强度、比刚度、比模量,良好的导热、导电、耐磨性及尺寸稳定性等优点,作为结构功能性材料应用于空间工程、电子封装、交通运输和精密仪器等领域。其研究热点主要集中在界面结构调控、强化机制及性能调控等方面。在SiCp/Al-Si复合材料中存在着增强体与基体界面、析出相与基体界面、析出相与增强体界面,这些界面受各种因素影响,会出现多种界面反应和界面产物,界面结构和结合状态复杂而多样。基于此,本文综述了制备工艺、基体合金成分和SiCp表面改性等方面对SiCp/Al-Si基复合材料界面结构的影响及调控,并总结了影响其力学性能的因素及强化机制的研究现状,最后对复合材料未来的发展及研究方向进行了展望。

A review of friction stir joining of SiCp/Al composites

SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace,automotive industry and other fields.Due to the huge difference in performance between SiC particles and matrix alloys,traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites.Friction stir joining(friction stir welding),as a solid phase joining process,has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process.Although some progress has been made in recent years,there are still full of challenges.In this paper,the research status of friction stir joining of SiCp/Al composites in recent years is expatiated,including the weldability of SiCp/Al composites,the macrostructure and the microstructure of joints,mechanical properties of joints,and tool wear and monitoring.Furthermore,the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.

Effect of rare earth addition on structure and properties of Ni-P coating on SiCp/Al composites

The aim of this work was to improve the properties of Ni-P coating on SiCp/Al composites. The effect of rare earths addition on Ni-P coating structure was investigated by means of scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffractometer (XRD) and electrochemistry methods. The results showed that as Y or La concentration was 0.15 g/L in plating solution, the highest value of deposition rate of Ni-P coating was found. And the structure of the obtained coating was modified...