To overcome the problems in design methodologies and construction control measures for the large open caisson, systematic research was conducted on the side friction calculation mode of the large open caisson. Based o...To overcome the problems in design methodologies and construction control measures for the large open caisson, systematic research was conducted on the side friction calculation mode of the large open caisson. Based on the field monitoring data of lateral soil pressure on the side wall of the open caisson for the southern anchorage of the Maanshan Yangtze River Highway Bridge, the statistical result of the side friction under different buried depths of the cutting edge of the open caisson was back-analyzed; and the side friction distribution of the large open caisson was underlined. The analysis results indicate that when the buried depth of the cutting edge is smaller than a certain depth H0, the side friction linearly increases with the increase in the buffed depth. However, as the buffed depth of the cutting edge is larger than H0, the side friction shows a distribution with small at both ends and large in the middle. The top of the distribution can be regarded as a linear curve, while the bottom as a hyperbolic curve. As the buffed depth of cutting edge increases continuously, the peak value of the side friction linearly increases and the location of the peak value gradually moves down. Based on the aforementioned conclusions, a revised calculation mode of the large open caisson is presented. Then, the calculated results are compared with the field monitoring data, which verifies the feasibility of the proposed revised calculation mode.展开更多
In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-si...In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-side FSW butt joint with more attention paid to the local characteristic zones.It was shown that a phenomenon of microstructural inhomogeneity existed in the nugget zone(NZ)through the thickness direction.The grain size presented an obvious gradient distribution from the top to the bottom for each single-pass weld,and the microhardness values decreased from both surfaces to the middle of the NZ.The lowest hardness zone(LHZ)exhibited a"hyperbolical"-shaped distribution extending to the middle of the NZ.Similar tensile properties were obtained in the three sliced specimens of the FSW joint,and the joint coefficient reached about 70%which achieved the same level as the conventional FSW Al alloy joints.Finite element modeling proved that the"hyperbolical"-shaped heat affected zone(HAZ)was beneficial to resisting the strain concentration in the middle layer specimen which helped to increase the tensile strength.Based on the analysis of the hardness contour map,tensile property and microstructural evolution of the joints,an Isothermal Softening Layer(ISL)model was proposed and established,which may have a helpful guidance for the optimization on the FSW of ultra-thick Al alloy plates.展开更多
基金Project supported by China Communications Construction Company Limited(No.2008-ZJKJ-11)
文摘To overcome the problems in design methodologies and construction control measures for the large open caisson, systematic research was conducted on the side friction calculation mode of the large open caisson. Based on the field monitoring data of lateral soil pressure on the side wall of the open caisson for the southern anchorage of the Maanshan Yangtze River Highway Bridge, the statistical result of the side friction under different buried depths of the cutting edge of the open caisson was back-analyzed; and the side friction distribution of the large open caisson was underlined. The analysis results indicate that when the buried depth of the cutting edge is smaller than a certain depth H0, the side friction linearly increases with the increase in the buffed depth. However, as the buffed depth of the cutting edge is larger than H0, the side friction shows a distribution with small at both ends and large in the middle. The top of the distribution can be regarded as a linear curve, while the bottom as a hyperbolic curve. As the buffed depth of cutting edge increases continuously, the peak value of the side friction linearly increases and the location of the peak value gradually moves down. Based on the aforementioned conclusions, a revised calculation mode of the large open caisson is presented. Then, the calculated results are compared with the field monitoring data, which verifies the feasibility of the proposed revised calculation mode.
基金supported by the Youth Innovation Promotion Association of the Chinese Academy of Sciences(2017236)National Natural Science Foundation of China under grant No.U1760201.
文摘In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-side FSW butt joint with more attention paid to the local characteristic zones.It was shown that a phenomenon of microstructural inhomogeneity existed in the nugget zone(NZ)through the thickness direction.The grain size presented an obvious gradient distribution from the top to the bottom for each single-pass weld,and the microhardness values decreased from both surfaces to the middle of the NZ.The lowest hardness zone(LHZ)exhibited a"hyperbolical"-shaped distribution extending to the middle of the NZ.Similar tensile properties were obtained in the three sliced specimens of the FSW joint,and the joint coefficient reached about 70%which achieved the same level as the conventional FSW Al alloy joints.Finite element modeling proved that the"hyperbolical"-shaped heat affected zone(HAZ)was beneficial to resisting the strain concentration in the middle layer specimen which helped to increase the tensile strength.Based on the analysis of the hardness contour map,tensile property and microstructural evolution of the joints,an Isothermal Softening Layer(ISL)model was proposed and established,which may have a helpful guidance for the optimization on the FSW of ultra-thick Al alloy plates.
