Carbonation of Dicalcium Silicate Enhanced by Ammonia Bicarbonate and Its Mechanism

The strength development law of γ-type dicalcium silicate (γ-C_(2)S) under different carbonation processes was investigated,and the carbonation mechanism of γ-C_(2)S under the action of NH_(4)HCO_(3) was clarified by using a wide range of test methods,including XRD and SEM.A method of saturated NH_(4)HCO_(3) solution as a curing agent was identified to improve the carbonation efficiency and enhance the carbonation degree of γ-C_(2)S,and then a high-strength carbonated specimen was obtained.Microhardness analysis and SEM morphology analysis were conducted on the carbonised specimens obtained under atmospheric pressure carbonisation conditions using the curing agent.It was found that γ-C_(2)S could perform carbonisation well under atmospheric pressure,which promoted the carbonisation efficiency and decreased the carbonisation cost simultaneously.Therefore,a new carbonisation process solution was proposed for the rapid carbonisation of γ-C_(2)S.

Natural Silicate as a Solid Support for the Calix[4]Thiophosphorus Derivative for Removal Mercury (II), as Picrate from Water

Currently a technique widely used for gold extraction is mercury by amalgamation technique, the tailing produced pollutes water of all kinds, so it is necessary to develop a form of selective mitigation, for which it is necessary to use complexing agents based on calixarene functionalized with mercury sequestering agents. These are immobilized by adding supports based on natural silica to form polymers and make them insoluble in all types of solvents, so that they can be used as an extractor and at the same time regenerate to their original properties for continuous reuse.

Effectiveness of Sodium Silicate on the Corrosion Protection of AA7075-T6 Aluminium Alloy in Sodium Chloride Solution

The influence of sodium silicate on the corrosion behaviour of aluminium alloy 7075-T6 in 0.1 M sodium chloride solution was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) techniques. Scanning electron microscopy (SEM) was used to characterize the AA7075-T6 surface. Silicate can significantly reduce corrosion deterioration and the inhibition efficiency increases with the concentration of Na2SiO3. The corrosion inhibition mechanism involves the formation of a protective film over the alloy surface by adsorption of aluminosilicate anions from solution, as has also been suggested by others in literature.

Influence of Na_(2)SiO_(3)/NaOH Ratio on Calcined Magnesium Silicate Based Geopolymer——Experimental and Predictive Study

This study aims to investigate the behavior of alkali activated mortar,which is made of naturally available magnesium silicate as source material.For magnesium silicate,ultrafine natural steatite powder(UFNSP)is used as the primary source of binder,and the activation is initiated through the alkali liquid which is proportioned in various combinations of silicate to hydroxide ratio(Na_(2)SiO_(3)/Na OH)ratio,and this ratio in this study varies from 1 to 3.The UFNSP is calcined at two difierent temperatures,700 and 1000℃.The mortar mix is proportioned as 1:3 between powder and the fine aggregate,and the mortar is prepared with hydroxide molarity(M)of 10 M.The mortar is cured for 48 hours at 60℃and the compressive strength was studied.All the mix were studied for its microstructural behavior along with compressive strength.The mix proportion of the mortar,and the results obtained through microstructural characterization were combinedly formed as input for artificial neural network(ANN)predictive modelling.The model is designed to predict the compressive strength,which is trained through Bayesian regularization algorithm with varying hidden neurons of 7 to 10.This experimental and predictive study shows that the strength is influenced by both Na_(2)SiO_(3)/Na OH ratio and calcination process.And the ANN is influenced by mainly calcination temperature and uncorrelation occurs in selected samples of 1000℃calcined UFNSP mix.

Selecting the Technology of Sodium Silicate Modified Poplar with the Highest Performance by Fuzzy Orthogonal Method

Sodium silicate modification can improve the overall performance of wood.The modification process has a great influence on the properties of modified wood.In this study,a new method was introduced to analyze the wood modification process,and the properties of modified wood were studied.Poplar wood was modified with sodium silicate by vacuum-pressure impregnation.After screening using single-factor experiments,an orthogonal experiment was carried out with solution concentration,impregnation time,impregnation pressure,and the cycle times as experimental factors.The modified poplar with the best properties was selected by fuzzy mathematics and characterized by SEM,FT-IR,XRD and TG.The results showed that some lignin and hemicellulose were removed from the wood due to the alkaline action of sodium silicate,and the orderly crystal area of poplar became disorderly,resulting in the reduction of crystallinity of the modified poplar wood.FT-IR analysis showed that sodium silicate was hydrolyzed to form polysilicic acid in wood,and structural analysis revealed the formation of Si-O-Si and Si-O-C,indicating that sodium silicate reacted with fibers on the wood cell wall.TG-DTG curves showed that the final residual mass of modified poplar wood increased from 25%to 67%,and the temperature of the maximum loss rate decreased from 343℃ to 276℃.The heat release and smoke release of modified poplar wood decreased obviously.This kind of material with high strength and fire resistance can be used in the outdoor building and indoor furniture.

Thermoluminescent response of gamma irradiated Na^(+)–Cu^(+) ionexchanged silicate glass in large dose range

The introduction of metals into vitreous matrices is the origin of various interesting phenomena;in particular,the presence of copper ions in glass has been the subject of considerable research because of its numerous applications.The ion-exchange process is primarily used to introduce copper ions into glass matrices.The thermoluminescence(TL)of silicate glass was studied to evaluate its potential as gamma-sensitive material for dosimetric applications;the effect of copper doping on the thermoluminescent sensitivity was investigated using the Cu-Na ion-exchange technique for different concentrations and doping conditions,over a wide dose range of 10 mGy to 100 kGy.The results showed that Cu doping significantly improved the sensitivity of the glasses to gamma radiation.After the ion-exchange,two peaks appeared in the glow curves at approximately 175 and 230°C,respectively,which possibly originated from the Cu^(+) centers,along with a weak TL peak at around 320℃.We also attempted to explain the origin of the observed thermoluminescence by exploiting the Electron paramagnetic resonance(EPR)spectra.The results clearly show quenching of the TL emission with increasing copper concentrations.The present work indicates that the thermoluminescence response of these glasses to gamma rays can be reasonably measured in the range of 0.001-100 kGy.This study also facilitates the understanding of the basic TL mechanism in this glass system.

Variation in concentration of dissolved silicate in the Eastern Philippine deep sea

Upper Circumpolar Deep Water(UCDW)and North Pacifi c Deep Water(NPDW)coexist in the upper deep layer(i.e.,with a 1.2-2.0-℃potential temperature range and a 2000-4100-dbar pressure range)of the Eastern Philippine Sea.They have similar properties in potential temperature and salinity,while have a signifi cant diff erence in dissolved silicate.Based on the repeated observations along a 137°E transect from the World Ocean Database(WOD18),this study revealed the interannual variability of dissolved silicate in the upper deep layer of the Eastern Philippine Sea.Dissolved silicate increased in 1995,1996,2005,2006,and 2007,and decreased in 1997,2000,2001,2002,and 2004.Composition analysis showed that the large diff erence between positive and negative dissolved silicate anomalies occurred mainly at~15°N and north of 25°N,with the concentration reaching 4.25μmol/g.Further analysis indicated that the interannual dissolved silicate variability was related to the zonal current variation in the upper deep layer.The relatively strong(weak)westward current transport increased(decreased)NPDW to the Eastern Philippine Sea,thereby resulting in increased(decreased)dissolved silicate.

Reclamation of CO_(2) sodium silicate used sands by steam leaching

The bond film on the surface of the CO_(2) sodium silicate used sands is not easy to decompose,therefore,it is difficult to reclaim used sands.A new reclamation method of CO_(2) sodium silicate used sands was developed by steam leaching,which can reduce the water consumption of reclamation and improve the removal effect of sodium silicate bond film.Firstly,the leaching effect of the sodium silicate sands after 20/200/400/600/800/1,000°C heat preservation treatment was simulated.Furthermore,the influence of the leaching time on the removal effect of the sodium silicate bond film was studied.Finally,the casting properties of the reclaimed sands after the leaching reclamation treatment were tested.The results show for simulated used sands after 30 min of steam leaching,the removal ratio of the alkali exceeds 84.1%,the removal ratio of silicate is 86.2%,and the removal ratio of carbonate is 93.6%.The removal rate of alkali,silicate and carbonate is relatively low in the leaching time of 30-50 min.Considering the reclamation effect and cost,the leaching time is controlled in 30 min.Water consumption is only 60%of the mass of used sands for 30 min steam leaching,while it is 200%for wet reclamation.Morphological analysis shows that most of the hazardous substances in the used sands are removed in 30 min steam leaching,and the reclaimed sands surface after steam leaching in 50 min is as smooth as new sands.After 30 min of steam leaching,the alkali removal effect of the factory used sands can reach 81.5%,the water consumption by the steam leaching reclamation is 58%of the mass of the used sand,which is similar to the result of simulated used sands.The performance of reclaimed sands obtained after 30 min steam leaching is better than that of new sands when the amount of sodium silicate added is 6%of the mass of the reclaimed sands and the CO_(2) blowing time is 15 s:the 24 h ultimate compressive strength of reclaimed sands is 5.6 MPa(equated with new sands),and the collapsibility compressive strength is 5.2 MPa,which is lower than the collapsibility compressive strength of new sands(7.7 MPa).This indicates that the reclamation of CO_(2) sodium silicate used sands by steam leaching is a feasible method.

Structure, Formation, Properties, and Application of Calcium and Magnesium Silicate Hydrates System—A Review

In order to expand the advantages of strong durability and high compressive strength of calcium silicate hydrates(C-S-H),at the same time to make up for the poor early mechanical strength of magnesium silicate hydrates (M-S-H),we present the features and advantages of C-S-H and M-S-H and a comprehensive review of the progress on CaO-MgO-SiO_(2)-H_(2)O.Moreover,we systematically describe natural calcium and magnesium silicate minerals and thermodynamic properties of CaO-MgO-SiO_(2)-H_(2)O.The effect of magnesium on C-S-H and calcium on M-S-H is summarized deeply;the formation and structural feature of CaO-MgO-SiO_(2)-H_(2)O is also explained in detail.Finally,the development of calcium and magnesium silicate hydrates in the future is pointed out,and the further research is discussed and estimated.

Improvement of Selected Morphological, Physiological, and Biochemical Parameters of Banana (Musa acuminata L.) Using Potassium Silicate under Drought Stress Condition Grown in vitro

Drought stress has become more common in recent years as a result of climate change impacts on the production of banana crops and other fruit trees.The growth and productivity of Musa spp are severely impacted by the gradual degradation of water resources and the erratic distribution pattern of annual precipitation amount.The aim of the work includes increased drought tolerance in light of water scarcity in the world as a result of the bananas’being gluttonous for water needs.This investigation was carried out from 2019 to 2020 to study the effect of potassium silicate on morphological growth and biochemical parameters of Musa acuminata L under drought stress by PEG.As a result,drought stress reduced the morphological characteristics such as shoots number,shoot length,roots number,and survival percentage and biochemical characteristics such as chlorophyll a,b,carotenoids,stomatal status,and RWC.While proline content increased in the leaf of M.acuminata L.Media complemented with K2SiO3(2 to 6 mM)either individually or in combination with PEG led to an improvement in all morphological and biochemical characteristics.The activities of CAT,POD,and PPO enzymes increased significantly compared to control.Furthermore,the lowest PPO,CAT,and POD activity were achieved.Additionally,K2SiO3 treatments under drought stress successfully enhanced the leaf stomatal behavior.Our results suggest that K2SiO3 can help to maintain plant integrity in the tested cultivar under drought stress.

Study on the Attack of Molten Silicates on Plasma-Sprayed Thermal Barrier Coatings

Thermal barrier coating (TBC) revolutionized the industry by allowing higher operating temperatures for equipment, such as gas turbines in the aeronautical industry. However, at high temperatures, the TBC is exposed to the attack of molten silicates, known as CMAS (Calcium-Magnesium-Alumino-Silicate), which are particles from the environment that infiltrate the TBC, causing delamination. In this study, samples coated with TBC by thermal spray and covered with CMAS were evaluated at temperatures of 1200˚C and 1250˚C. For each temperature, exposure times of 1 h and 5 h were used. Samples with longer exposure time had a considerable volume increase. The main contribution of this work was to demonstrate the non-wettability of the CMAS, even in the 5-h heat treatments, which prevented its infiltration in the deeper regions. The conditions to guarantee the formation of the silicate and its consequent wettability are also discussed.

Study on Multi-Scale Tensile Strength and Tensile Strain of Calcium Silicate Hydrate Layered Nanocomposites Under External Physical Field

Calcium silicate hydrate(C-S-H)is the mainly strength source of cement-based materials,but there is little basic research.In this paper,molecular dynamics method is applied to analyze the multi-scale tensile strength and tensile strain of C-S-H layered materials under the condition of external physical fields(temperature and strain rate).The results show that the tensile strength and strain of C-S-H model decrease with temperature raises.The temperature(from 1 K to 600 K)has obvious influence on the tensile strain and strength of C-S-H layered materials.In addition,at(0.00025 ps^(-1)-0.001 ps^(-1)),the tensile strain and strength of C-S-H layered materials are less sensitive to strain rate.The whole model is closer to a 3-dimensional deformation.However,at(0.001 ps^(-1)-0.005 ps^(-1)),the dynamic load effect begins to increase,and the work done by the load per unit time increased.The tensile strain and strength of C-S-H layered materials indicates intensified by the change of strain rate.The energies are randomly distributed in the system,not concentrated in a certain area.

Research and Advances of Silicate Plugging Agent in the Oilfields

The paper overviews the research and application of silicate plugging agent, according to the different mechanisms and application forms, the plugging agent is divided into silicate gel, silicate precipitation, silicate/polymer, silicate/surfactant, silicate gel/foam and so on. This paper chiefly introduces the conception, mechanism and development tendency of the different systems mentioned above. The development tendency manifests as fully utilize personal properties and cooperate with other plugging agents or technologies, including the study of reaction mechanism, combination of plugging agent, grasping water flood timing, developing deep profile control and water shutoff technology, combining with other measures (chemicals huff and puff), in order to play the role of such blocking agents, further enhance oil recovery.

Occurrence mechanism of silicate and aluminosilicate minerals in Sarcheshmeh copper flotation concentrate

The Sarcheshmeh copper flotation circuit is producing 5× 10^4 t copper concentrate per month with an averaging grade of 28% Cu in rougher, cleaner and recleaner stages. In recent years, with the increase in the open pit depth, the content of aluminosilicate minerals increased in plant feed and subsequently in flotation concentrate. It can motivate some problems, such as unwanted consumption of reagents, decreasing of the copper concentrate grade, increasing of Al2O3 and SiO2 in the copper concentrate, and needing a higher temperature in the smelting process. The evaluation of the composite samples related to the most critical working period of the plant shows that quartz, illite, biotite, chlorite, orthoclase, albeit, muscovite, and kaolinite are the major Al2O3 and SiO2 beating minerals that accompany chalcopyrite, chalcocite, and covellite minerals in the plant feed. The severe alteration to clay minerals was a general rule in all thin sections that were prepared from the plant feed. Sieve analysis of the flotation concentrate shows that Al2O3 and SiO2 bearing minerals in the flotation concentrate can be decreased by promoting the size reduction from 53 to 38 μm. Interlocking of the Al2O3 and SiO2 bearing minerals with chalcopyrite and chalcocite is the occurrence mechanism of silicate and aluminosilicate minerals in the flotation concentrate. The dispersed form of interlocking is predominant.

Identification and Practical Application of Silicate-dissolving Bacteria

Slime-forming bacteria were isolated from soils, rock surface and earthworm intestine, and their effects on dissolving silicate minerals and tomato growth were examined. One of the bacteria, Bacillus mucilaginosus RGBc13, had particularly strong ability to form slime and dissolve silicates. RGBc13 could also colonize and develop in both non-rhizosphere and rhizosphere soil. Total number of slime-forming bacteria increased from 2.9 × 103 cfu·g-1and 8.4 × 103 cfu·g-1 to 9.6 × 106 cfu·g-1 and 6.0 × 107 cfu·g-1 in the non-rhizosphere and rhizosphere soils respectively. Potassium and phosphorus nutritional conditions in the rhizosphere were markedly improved through inoculation of this bacterium. Available K and P respectively increased from 25. 86 and 3. 63mg · kg-1 in the non-rhizosphere soil to 91. 23 and 5. 74mg · kg-1 in the rhizosphere soil. Tomato biomass increased by 125%, K and P uptakes were more than 150%, greater than the non-inoculation. Thus, there is a potential in applying RGBcl3 for improving plant K and P nutrition.

Determination of Iron in Layered Crystal Sodium Disilicate and Sodium Silicate by Flame Atomic Absorption Spectrometry with Boric Acid as a Matrix Modifier

The effects of matrix silicate and experimental conditions on the determination of iron in flame atomic absorption spectrometry （FAAS） were investigated. It was found that boric acid as a matrix modifier obviously eliminated silicate interference. Under the optimum operating conditions, the determination results of iron in layered crystal sodium disilicate and sodium silicate samples by FAAS were satisfactory. The linear range of calibration curve is 0-10.5 μg.mL^-1, the relative standard deviation of method is 1.2%-2.2%, the recovery of added iron is 96.0%- 101%, the sensitivity is 0.19 μg.mL^-l and the detection limit is 77 ng.mL^-1. The effect of the determination of iron of the standard curve method, standard addition calibration and colorimetry method was the same, but the first has the merits of rapid sample preparation, reduced contamination risks and fast analysis.

Effect of Minor Elements on Silicate Cement Clinker

The effect of rare-earth and HX addition agent on the burn-ability of silicate cement dinker was investigated by orthogonal experiment. The result shows, compared with blank sample, f CaO of the .samples added with rare-earth and HX agent drops by 84.95% , its 3 d and 28d compressive strength enhances by 24.40% and 16.90% , respectively. It was discovered by means of X-ray diffrnction and high temperature microscope analysis that sintering temperature of the sample added with rare-earth and HX addition agent is about 1320℃. At the same time, the tmrning temperature of triealeium silicate desends and its crystal growth forming- rate increases. Tricalcium silicate content in burning clinker is higher and its crystal is larger.

STUDY ON THE POLYMERIZATION DEGREE OF SILICATE ANIONS IN THE SILICATE GLASS BY TRIMETHYLSILYLATION METHOD

In the present paper,a mixed solvent method is applied to the trimethylsilylation of silicate glass,and the polymerization degree and its distribution of silicate anions in the silicate glass are measured by means of the analyses of gas chromatography-mass spectrography.

Adsorption of Methylene Blue on magnesium silicate: Kinetics, equilibria and comparison with other adsorbents

Batch adsorption from aqueous solutions in a slightly basic medium of Methylene Blue, up to 2500 mg/L, onto synthetic magnesium silicate （Florisil） of three particle size ranges （mean diameters of 112, 200 and 425 μm） was compared to the corresponding adsorption onto activated carbon and Amberlite XAD-2. The best fit of the kinetic results was achieved by a pseudo second-order equation. The equilibrium data were found to be well represented by the Langmuir isotherm equation. Amberlite XAD-2, an unspecific adsorbent capable of adsorbing exclusively through a surface effect, exhibited a poor dye uptake, confirming that the adsorption mechanism on Florisil was due to electrostatic attraction and ion exchange. Moreover, the comparison between Florisil and the other adsorbents was performed on the basis of the evaluation of the surface area and pore volume occupied by the adsorbed dye.

Fractionation and solubility of cadmium in paddy soils amended with porous hydrated calcium silicate

Previous studies have shown that porous hydrated calcium silicate （PS） is very effective in decreasing cadmium （Cd） content in brown rice. However, it is unclear whether the PS influences cadmium transformation in soil. The present study examined the effect of PS on pH, cadmium transformation and cadmium solubility in Andosol and Alluvial soil, and also compared its effects with CaCO3, acidic porous hydrated calcium silicate （APS） and silica gel. Soil cadmium was operationally fractionationed into exchangeable （Exch）, bound to carbonates （Carb）, bound to iron and manganese oxides （FeMnOx）, bound to organic matters （OM） and residual （Res） fraction. Application of PS and CaCO3 at hig rates enhanced soil pH, while APS and silica gel did not obviously change soil pH. PS and CaCO3 also increased the FeMnOx-Cd in Andosol and Carb-Cd in Alluvial soil, thus reducing the Exch-Cd in the tested soils. However, PS was less effective than CaCO3 at the same application rate. Cadmium fractions in the two soils were not changed by the treatments of APS and silica gel. There were no obvious differences in the solubility of cadmium in soils treated with PS, APS, silica gel and CaCO3 except Andosol treated 2.0% CaCO3 at the same pH of soil-CaC12 suspensions. These findings suggested that the decrease of cadmium availability in soil was mainly attributed to the increase of soil pH caused by PS.