Effect of sodium starch octenyl succinate-based Pickering emulsion on the physicochemical properties of hairtail myofibrillar protein gel subjected to multiple freeze-thaw cycles

A Pickering emulsion based on sodium starch octenyl succinate(SSOS)was prepared and its effects on the physicochemical properties of hairtail myofibrillar protein gels(MPGs)subjected to multiple freeze-thaw(F-T)cycles were investigated.The whiteness,water-holding capacity,storage modulus(G')and texture properties of the MPGs were significantly improved by adding 1%-2%Pickering emulsion(P<0.05).Meanwhile,Raman spectral analysis demonstrated that Pickering emulsion promoted the transformation of secondary structure,enhanced hydrogen bonds and hydrophobic interactions,and promoted the transition of disulfide bond conformation from g-g-g to g-g-t and t-g-t.At an emulsion concentration of 2%,theα-helix content decreased by 10.37%,while theβ-sheet content increased by 7.94%,compared to the control.After F-T cycles,the structure of the MPGs was destroyed,with an increase in hardness and a decrease in whiteness and water-holding capacity,however,the quality degradation of MPGs was reduced with 1%-2%Pickering emulsion.These findings demonstrated that SSOS-Pickering emulsions,as potential fat substitutes,can enhance the gel properties and the F-T stability of MPGs.

Oil-in-water nanoemulsions loaded with lycopene extracts encapsulated by spray drying:Formulation,characterization and optimization

Lycopene is very susceptible to degradation once released from the protective chromoplast environment.In this study,oil-in-water(O/W)nanoemulsions coupled with spray drying technology were applied for the encapsulation and stabilization of lycopene extracted from tomato waste.Tomato extract was obtained by ultrasound-assisted extraction.Nanoemulsions were prepared by a high-speed rotor stator using isopropyl myristate as the oil phase and Pluronic F-127 as the emulsifier for the aqueous external phase.The effect of emulsification process parameters was investigated.Spray drying of the produced emulsions was attempted to obtain a stabilized dry powder after the addition of a coating agent.The effect of different coating agents(maltodextrin,inulin,gum arabic,pectin,whey and polyvinylpyrrolidone),drying temperature(120-170℃),and feed flow rate(3-9 ml·min^(-1))on the obtained particles was evaluated.Results revealed that the emulsion formulation of 20/80(O/W)with 1.5%(mass fraction)of Pluronic F-127 as stabilizer in the aqueous phase resulted in a stable nanoemulsion with droplet sizes in the range of 259-276 nm with a unimodal and sharp size distribution.The extract in the nanoemulsion was well protected at room temperature with a degradation rate of lycopene of about 50%during a month of storage time.The most stable emulsions were then processed by spray drying to obtain a dry powder.Spray drying was particularly successful when using maltodextrin as a coating agent,obtaining dried spherical particles with mean diameters of(4.87±0.17)μm with a smooth surface.The possibility of dissolving the spray dried powder in order to repristinate.The original emulsion was also successfully verified.

Insights into the enhancement of food flavor perception:strategies,mechanism and emulsion applications

The core drivers of the modern food industry are meeting consumer demand for tasty and healthy foods.The application of food flavor perception enhancement can help to achieve the goals of salt-and sugar-reduction,without compromising the sensory quality of the original food,and this has attracted increasing research attention.The analysis of bibliometric results from 2002 to 2022 reveals that present flavor perception enhancement strategies(changing ingredient formulations,adding salt/sugar substitutes,emulsion delivery systems)are mainly carry out based on sweetness,saltiness and umami.Emulsion systems is becoming a novel research foci and development trends of international food flavor perception-enhancement research.The structured design of food emulsions,by using interface engineering technology,can effectively control,or enhance the release of flavor substances.Thus,this review systematically summarizes strategies,the application of emulsion systems and the mechanisms of action of food flavor perception-enhancement technologies,based on odor-taste cross-modal interaction(OTCMI),to provide insights into the further structural design and application of emulsion systems in this field.

Anti-abrasion collagen fiber-based membrane functionalized by UiO-66-NH_(2)with ultra-high efficiency and stability for oil-in-water emulsions separation

Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present significant challenges.In this study,we report a CFM@UiO-66-NH_(2)membrane with high separation flux,efficiency and stability,through utilizing a robust anti-abrasion collagen fiber membrane(CFM)as the multifunctional support and UiO-66-NH_(2)by an in-situ growth as the separation layer.The high mechanical strength of the CFM compensated for the weakness of the separation layer,while the charge-breaking effect of UiO-66-NH_(2),along with the size sieving of its constituent separating layers and the capillary effect of the collagen fibers,contributed to the potential for efficient separation.Additionally,the CFM@UiO-66-NH_(2)membrane exhibited superhydrophilic properties,making it suitable for separating oil-in-water microemulsions and nanoemulsions stabilized by anionic surfactants.The membrane demonstrated remarkable separation efficiencies of up to 99.960%and a separation flux of370.05 L·m^(-2)·h^(-1).Moreover,it exhibits stability,durability,and abrasion resistance,maintaining excellent separation performance even when exposed to strong acids and alkalis without any damage to its structure and performance.After six cycles of reuse,it achieved a separation flux of 417.97 L·m^(-2)·h^(-1)and a separation efficiency of 99.747%.Furthermore,after undergoing 500 cycles of strong abrasion,the separation flux remained at 124.39 L·m^(-2)·h^(-1),with a separation efficiency of 99.992%.These properties make it suitable for the long-term use in harsh operating environments.We attribute these properties to the electrostatic effect resulting from the amino group on UiO-66-NH_(2)and its in-situ growth on the CFM,which forms a size-screening separation layer.Our work highlights the potential of the CFM@UiO-66-NH_(2)membrane as an environmentally friendly size-screening material for the efficient emulsion wastewater separation.

Pickering emulsion transport in skeletal muscle tissue:A dissipative particle dynamics simulation approach

Lymph node targeting is a commonly used strategy for particulate vaccines,particularly for Pickering emulsions.However,extensive research on the internal delivery mechanisms of these emulsions,especially the complex intercellular interactions of deformable Pickering emulsions,has been surprisingly sparse.This gap in knowledge holds significant potential for enhancing vaccine efficacy.This study aims to address this by summarizing the process of lymph-node-targeting transport and introducing a dissipative particle dynamics simulation method to evaluate the dynamic processes within cell tissue.The transport of Pickering emulsions in skeletal muscle tissue is specifically investigated as a case study.Various factors impacting the transport process are explored,including local cellular tissue environmental factors and the properties of the Pickering emulsion itself.The simulation results primarily demonstrate that an increase in radial repulsive interaction between emulsion particles can decrease the transport efficiency.Additionally,larger intercellular gaps also diminish the transport efficiency of emulsion droplet particles due to the increased motion complexity within the intricate transport space compared to a single channel.This study sheds light on the nuanced interplay between engineered and biological systems influencing the transport dynamics of Pickering emulsions.Such insights hold valuable potential for optimizing transport processes in practical biomedical applications such as drug delivery.Importantly,the desired transport efficiency varies depending on the specific application.For instance,while a more rapid transport might be crucial for lymph-node-targeted drug delivery,certain applications requiring a slower release of active components could benefit from the reduced transport efficiency observed with increased particle repulsion or larger intercellular gaps.

Hyperspectral remote sensing identification of marine oil emulsions based on the fusion of spatial and spectral features

Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protection of marine environments.However,the spectrum of oil emulsions changes due to different water content.Hyperspectral remote sensing and deep learning can use spectral and spatial information to identify different types of oil emulsions.Nonetheless,hyperspectral data can also cause information redundancy,reducing classification accuracy and efficiency,and even overfitting in machine learning models.To address these problems,an oil emulsion deep-learning identification model with spatial-spectral feature fusion is established,and feature bands that can distinguish between crude oil,seawater,water-in-oil emulsion(WO),and oil-in-water emulsion(OW)are filtered based on a standard deviation threshold–mutual information method.Using oil spill airborne hyperspectral data,we conducted identification experiments on oil emulsions in different background waters and under different spatial and temporal conditions,analyzed the transferability of the model,and explored the effects of feature band selection and spectral resolution on the identification of oil emulsions.The results show the following.(1)The standard deviation–mutual information feature selection method is able to effectively extract feature bands that can distinguish between WO,OW,oil slick,and seawater.The number of bands was reduced from 224 to 134 after feature selection on the Airborne Visible Infrared Imaging Spectrometer(AVIRIS)data and from 126 to 100 on the S185 data.(2)With feature selection,the overall accuracy and Kappa of the identification results for the training area are 91.80%and 0.86,respectively,improved by 2.62%and 0.04,and the overall accuracy and Kappa of the identification results for the migration area are 86.53%and 0.80,respectively,improved by 3.45%and 0.05.(3)The oil emulsion identification model has a certain degree of transferability and can effectively identify oil spill emulsions for AVIRIS data at different times and locations,with an overall accuracy of more than 80%,Kappa coefficient of more than 0.7,and F1 score of 0.75 or more for each category.(4)As the spectral resolution decreasing,the model yields different degrees of misclassification for areas with a mixed distribution of oil slick and seawater or mixed distribution of WO and OW.Based on the above experimental results,we demonstrate that the oil emulsion identification model with spatial–spectral feature fusion achieves a high accuracy rate in identifying oil emulsion using airborne hyperspectral data,and can be applied to images under different spatial and temporal conditions.Furthermore,we also elucidate the impact of factors such as spectral resolution and background water bodies on the identification process.These findings provide new reference for future endeavors in automated marine oil spill detection.

Influence of the Powder on the Properties of the Liquid Crystal Emulsions

The purpose of study was to evaluate the effect of four powder including titanium dioxide,bismuth oxychloride,silica,and kaolin on the properties of the liquid crystal emulsions.The results show that the addition of titanium dioxide and bismuth oxychloride had no obvious effect on the liquid crystal structure.In addition,the addition of Kaolin and silica have an effect on the stability of the liquid crystal structure.Sensory evaluation and Texture analyzer results shown that the addition of titanium dioxide and bismuth oxychloride had no obvious effect on the spreadability of liquid crystal system.The addition of silica and Kaolin was increased the hardness and adhesive of the liquid crystal system.Rheological experiments shown that the kaolin system had lower structural stability.the system with titanium dioxide,bismuth oxychloride,and silica has good stability.This paper provides data support for the application of powders in the formulation of liquid crystal system,which aims to provide a data basis for the preparation and applications of liquid crystal emulsion.

Experimental investigation on using CO_(2)/H_(2)O emulsion with high water cut in enhanced oil recovery

CO_(2) emulsions used for EOR have received a lot of interest because of its good performance on CO_(2)mobility reduction.However,most of them have been focusing on the high quality CO_(2) emulsion(high CO_(2) fraction),while CO_(2) emulsion with high water cut has been rarely researched.In this paper,we carried out a comprehensive experimental study of using high water cut CO_(2)/H_(2)O emulsion for enhancing oil recovery.Firstly,a nonionic surfactant,alkyl glycosides(APG),was selected to stabilize CO_(2)/H_(2)O emulsion,and the corresponding morphology and stability were evaluated with a transparent PVT cell.Subsequently,plugging capacity and apparent viscosity of CO_(2)/H_(2)O emulsion were measured systematically by a sand pack displacement apparatus connected with a 1.95-m long capillary tube.Furthermore,a high water cut(40 vol%) CO_(2)/H_(2)O emulsion was selected for flooding experiments in a long sand pack and a core sample,and the oil recovery,the rate of oil recovery,and the pressure gradients were analyzed.The results indicated that APG had a good performance on emulsifying and stabilizing CO_(2) emulsion.An inversion from H_(2)O/CO_(2) emulsion to CO_(2)/H_(2)O emulsion with the increase in water cut was confirmed.CO_(2)/H_(2)O emulsions with lower water cuts presented higher apparent viscosity,while the optimal plugging capacity of CO_(2)/H_(2)O emulsion occurred at a certain water cut.Eventually,the displacement using CO_(2)/H_(2)O emulsion provided 18.98% and 13.36% additional oil recovery than that using pure CO_(2) in long sand pack and core tests,respectively.This work may provide guidelines for EOR using CO_(2) emulsions with high water cut.

Progress in Preparation and Application of Gel-Emulsions

Compared to conventional emulsions, gel-emulsions have a higher internal phase volume fraction, unique structures and properties, higher viscosity, and tunable internal structures. These advantages make them widely applicable in the cosmetics industry, food industry, aerospace, and biomedicine, with significant potential in the development of new materials and high-performance products. The factors affecting the stability of gel-emulsions, as well as the types of stabilizers required for their preparation (including solid particles, surfactants, and small molecule gelators), and the corresponding preparation methods (including the one-step method, two-step method, and phase inversion method) are reviewed in this article. The applications of gel-emulsions in porous materials, food, cosmetics, and stimuli-responsive materials are introduced, and future research directions are also discussed.

The use of bacterial cellulose from kombucha to produce curcumin loaded Pickering emulsion with improved stability and antioxidant properties

Curcumin is a bioactive molecule with limited industrial application because of its instability and poor solubility in water.Herein,curcumin-loaded Pickering emulsion was produced using purified bacterial cellulose from fermented kombucha(KBC).The morphology,particle size,stability,rheological properties,and antioxidant activities of the curcumin-loaded Pickering emulsion were investigated.The fluorescence microscope and scanning electron microscopy images showed that the curcumin-loaded Pickering emulsion formed circular droplets with good encapsulation.The curcumin-load Pickering emulsion exhibited better stability under a wide range of temperatures,low p H,sunlight,and UV-365 nm than the free curcumin,indicating that the KBC after high-pressure homogenization improved the stability of the CPE.The encapsulated curcumin retained its antioxidant capacity and exhibited higher functional potential than the free curcumin.The study demonstrated that the KBC could be an excellent material for preparing a Pickering emulsion to improve curcumin stability and antioxidant activity.

Rheo-optic in situ synchronous study on the gelation behaviour and mechanism of waxy crude oil emulsions

An improved rheo-optic in situ synchronous measurement system was employed to investigate the gelation behaviour and mechanism of waxy crude oil emulsions. By combining transmitted natural light and reflected polarized light microscopy, a multiangle composite light source was built to achieve the simultaneous observation of wax crystals and emulsified water droplets, as well as their dynamic aggregation process. Main outcomes on the microscopic mechanism were obtained by developed microscopic image processing method. It was found that the microstructure of W/O waxy crude oil emulsion has the evolution of “individual structure--homogeneous aggregate structure--heterogeneous coaggregate structure--floc structure” during the static cooling, which results in the four stages during gelation process. Different from previous studies, the aggregation of emulsified water droplets was found to be more significant and contributes to the formation and development of the wax crystals-emulsified water droplets coaggregate, which plays a decisive role in the further evolution of the gelled microstructure. Time series microscopic images show the dynamic aggregation of emulsified water droplets and wax crystals. Two different aggregation behaviours between wax crystals and water droplets were observed. That wax crystals can not only embed in gaps between adjacent water droplets and enhance the structure, but also surround the outside of the water droplets and continue to grow resulting in the interconnection of different coaggregates to form a larger floc structure. In addition, correlation between viscoelasticity and microstructure evolution of waxy crude oil emulsions of different water contents was discussed. With increasing water contents, the microstructure is changed from wax crystal flocculation structure as the main skeleton and the emulsified water droplets embedded in it, into the aggregation of emulsified water droplets occupying the main position. When the number of wax crystals and water droplets reaches a certain ratio, did wax crystals form coaggregates with emulsified water droplets, and the remaining wax crystals formed an overall flocculation structure, the viscoelasticity of the waxy crude oil emulsion is the highest.

Synthesis of Microcrystalline Cellulose—Polyvinyl Alcohol Stabilized Polyvinyl Acetate Emulsion

Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.

Design and manufacture of emulsion liquid membrane based on various amine extractants for separation and extraction of succinic acid from fermentation broth

The aim of this study was to design a new emulsion liquid membrane(ELM)system for the separation of succinic acid from aqueous solutions.The concentration of succinic acid varied from 20 to 60 mmol·L^(-1).The prepared ELM system includes tributylamine(TBA)as a carrier,commercial kerosene as a solvent,Span 80 as a surfactant,and Na2CO3as a stripping agent.In order to control the membrane swelling,different values of cyclohexanone were added to the membrane phase.The effect of various empirical variables on the extraction of the succinic acid such as acid concentration in the feed solution,initial feed concentration,carrier concentration,the stirring speed of the extraction,Na2CO3,surfactant,and cyclohexanone concentrations,and treat ratio in the ELM system.The best result was obtained when TBA was used as the carrier.The final acid extraction efficiency was independent of pH variations of the aqueous feed solution.The extraction of succinic acid solution with a concentration of 40 mmol·L^(-1)was improved by increasing the treat ratio 1:7-1:3,stripping phase concentration 0.5-1.5 mol·L^(-1),stirring speed 300-500 r·min^(-1)and cyclohexanone concentration in the membrane phase 1.2-1.6 mol·L^(-1).No considerable effect on the extraction rate was observed for the carrier concentration in the membrane phase.But,the surfactant concentration in the feed phase showed a dual effect on the extraction efficiency.

Temperature-induced hydrophobicity transition of MXene membrane for directly preparing W/O emulsions

Although hydrophilic membranes are desired for reducing resistance to water permeation, hydrophilic surfaces are not used in the water-in-oil(W/O) membrane emulsification process because water spreads on the hydrophilic surface without forming droplets. Here, we report that a hydrophilic ceramic membrane can form a hydrophobic interface in diesel at a higher temperature;interestingly, the experiments show that the contact angle increases when the temperature rises. The hydrophilic membrane surface evolves into a hydrophobic interface, particularly near the boiling point of water, resulting in a water contact angle of 147.5° ± 1.2°. This work established a method for preparing W/O monodispersed emulsions by direct emulsification of hydrophilic ceramic membranes at a temperature close to the boiling point of water.Additionally, it made high flux of membrane emulsification of monodispersed W/O emulsions possible,which satisfied the industrial requirements of fluidized catalytic cracking in the petrochemical industry.

Demulsification Behavior, Characteristics, and Performance of Surfactant Stabilized Oil-in-Water Emulsion under Bidirectional Pulsed Electric Field

As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsification behavior,characteristics,and stages under BPEF were explored.It was discovered that BPEF drove SSO/W emulsion to move and form vortexes,during which the oil droplets aggregated and accumulated to generate an oil droplet layer(ODL).ODL subsequently transformed into a continuous oil layer(COL)leading to the demulsification and separation of SSO/W emulsion.The conversion rate of ODL to COL was defined and used to evaluate the demulsification process and reflect the coalescence ability and transformation efficiency of dispersed oil droplets into COL.Furthermore,the effects of BPEF voltage,frequency,duty cycle,ratio of pulse output time,and surfactant type and content on the demulsification performance were examined.The optimal values of BPEF parameters for demulsification operation were 400 V,25 Hz,50%,and 4:1.O/W emulsion containing anionic surfactant was apt to be demulsified by BPEF,nonionic surfactant took the second place and cationic surfactant was the most difficult.A high surfactant content was not conducive to the BPEF demulsification.This work is anticipated to provide useful guidance for oil/water separation and oil recovery from actual emulsified oily wastewater by BPEF.

Interaction of 28Si with Emulsion Nuclei at 4.5 AGeV/c in View of Thermo-Statistical Approach

In this work, we study some changes of nuclear matter in the interactions of 28Si with emulsion nuclei at 4.5 AGeV/c. From the experimental quantities investigated using Tsallis’ statistics, we deduced the temperature, entropy density and non-equilibrium factor of the nuclear medium. These obtained parameters were used to reveal variations in the nuclear matter at the stated interaction energy. The results that came up from this study were compared with their corresponding results obtained from other heavy ion collision experiments at wide energy range.

Effect of carboxymethyl konjac glucomannan coating on curcumin-loaded multilayered emulsion:stability evaluation

The stability against various environmental stresses of the curcumin-loaded secondary and tertiary emulsions that was emulsified by whey protein isolate(WPI)and coated by chitosan(CHI),carboxymethyl konjac glucomannan(CMKGM),or their combination through layer-by-layer assembly was investigated.Generally,the multilayered emulsions were destabilized in high Na Cl concentrations or medium p H that could interrupt the electrostatic interaction between the three polyelectrolytes or deprotonate CHI,indicating that electrostatic interaction played an important role in the stability of emulsions.Compared with the primary emulsion that was solely stabilized by WPI,extra coating with CHI and CMKGM generally increased the stability of the emulsion against repeated freezing-thawing,improved the retention of curcumin against heating,UV irradiation,and long-term storage,and the effects were more remarkable in the tertiary emulsion with CMKGM locating in the outmost layer.Since CMKGM has shown the colon-targeted delivery potency,the multilayered emulsions assembled by layer-by-layer deposition,especially the tertiary emulsion,could be used as an effective carrier for the targeted delivery of curcumin.

3D inner-outer asymmetric sponge for enormous-volume emulsion wastewater treatment based on a new“demulsification-transport”mechanism

Although oily wastewater treatment realized by superwetting materials has attracted heightened attention in recent years,how to treat enormous-volume emulsion wastewater is still a tough problem,which is ascribed to the emulsion accumulation.Herein,to address this problem,a material is presented by subtly integrating chemical demulsification and 3D inner-outer asymmetric wettability to a sponge substrate,and thus wettability gradient-driven oil directional transport for achieving unprecedented enormous-volume emulsion wastewater treatment is realized based on a“demulsification-transport”mechanism.The maximum treatment volume realized by the sponge is as large as 3 L(2.08×10^(4) L per cubic meter of the sponge)in one cycle,which is about 100 times of the reported materials.Besides,owing to the large pore size of the sponge,9000 L m^(2)h^(-1)(LMH)separation flux and 99.5%separation efficiency are realized simultaneously,which overcomes the trade-off dilemma.Such a 3D inner-outer asymmetric sponge displaying unprecedented advantage in the treatment volume can promote the development of the oily wastewater treatment field,as well as expand the application prospects of superwetting materials,especially in continuous water treatment.

Preparation and Characterization of Biobased Dehydroabietyl Polyethylene Glycol Glycidyl Ether-Grafted Hydroxyethyl Cellulose with High Emulsifying Property

Dehydroabietyl polyethylene glycol glycidyl ether-grafted hydroxyethyl cellulose(HEC)polymer surfactant(DA(EO)5GE-g-HEC)was prepared using ring-opening polymerization with biobased rosin and hydroxyethyl cellulose as feedstocks.Dehydroabietyl polyethylene glycol glycidyl ether(DA(EO)5GE)was formed by condensation of dehydroabietyl alcohol polyoxyethylene ether(Rosin derivative:DA(EO)5H)and epichlorohydrin.The grafting degree of DA(EO)5GE-g-HEC was manipulated by adjusting the mass ratio of HEC and DA(EO)5GE and confirmed by EA.According to the formula,when m(HEC)/m(DA(EO)2GE)was 1:1~1:5,the grafting rate of DA(EO)5GE in DA(EO)5GE-g-HEC varied from 34.43%to 38.33%.The surface activity and foam properties of DA(EO)5GE-g-HEC aqueous solution were studied.The results showed that with the increase in grafting rate,the critical micellar concentration(CMC)in aqueous solution changed from 1.28 to 0.96 g/L.The results of the thermogravimetric analysis showed that the temperature range of the main stage of mass loss of DA(EO)5GE-g-HEC was 310°C~410°C,and the thermal decomposition processes of the samples with five mass ratios were similar.An oil in water emulsion was prepared by choosing cyclohexane as the oil phase and DA(EO)5GE-g-HEC as the emulsifier.The effect of DA(EO)5GE-g-HEC mass fraction on emulsion particle size and stability was analyzed.The results suggested that when the oil-water ratio was 8:2 with 0.4%emulsifier,the emulsion droplets were the smallest in terms of particle size and were the most stable.The rheological test results showed that the apparent viscosity decreased with the increase in shear rate and showed a typical elastic gel phenomenon.

Effects of Different Heavy Crude Oil Fractions on the Stability of Oil-in-water Emulsions —— Isolation of functional fractions from heavy crude oil and study of their properties

The functional fractions (acid, basic, amphoteric and neutral fractions) are isolated from the Liaohe Du-84 heavy crude oil and Shengli Gudao Kenxi heavy crude oil by ion-exchange chromatography, but the conventional fractions (saturates, aromatics, resins and asphaltenes) are also isolated from the heavy crude oil. These components have been characterized by spectroscopic methods (FT-IR), namely acid number, basic nitrogen number, ultimate analysis and molecular weight measurements using vapor pressure osmometry (VPO). The ion-exchange chromatography method based on separation by a functional group induces a little change on the nature of the crudes and reasonable mass balances can be easily obtained.