Theoretical calculations of thermophysical properties of single-wall carbon nanotube bundles

Carbon nanotube bundles are promising thermal interfacial materials due to their excellent thermal and mechanical characteristics. In this study, the phonon dispersion relations and density of states of the single-wall carbon nanotube bundles are calculated by using the force constant model. The calculation results show that the inter-tube interaction leads to a significant frequency raise of the low frequency modes. To verify the applied calculation method, the specific heat of a single single-wall carbon nanotube is calculated first based on the obtained phonon dispersion relations and the results coincide well with the experimental data. Moreover, the specific heat of the bundles is calculated and exhibits a slight reduction at low temperatures in comparison with that of the single tube. The thermal conductivity of the bundles at low temperatures is calculated by using the ballistic transport model. The calculation results indicate that the inter-tube interaction, i.e. van der Waals interaction, hinders heat transfer and cannot be neglected at extremely low temperatures. For （5, 5） bundles, the relative difference of the thermal conductivity caused by ignoring inter-tube effect reaches the maximum value of 26% around 17 K, which indicates the significant inter-tube interaction effect on the thermal conductivity at low temperatures.

Single-Wall Carbon Nanotube Growth from Graphite Layers-a Tight Binding Molecular Dynamics Simulation

The growth of single-wall carbon nanotube from graphite layers is studied by tight binding molecular dynamics simulation. Given temperature of 2500 K or 3500 K and an interval of 0.25 nm for the two layers of graphite, a single-wall carbon nanotube with a zigzag shell will be produced. On the other conditions the carbon nanotube cannot grow or grows with too many defects. All carbon nanotube ends have pentagons which play an important role during the tube ends closing.

Prediction of the Frontier Electronic States in a Finite Single-wall Carbon Nanotube

A theoretical model is summarized into the shorter vector principle. It is used to predict the topological structure of wave function and the oscillation rule of energy gap in various types of finite carbon nanotubes （CNTs）. The theoretical model indicates that the characteristics of the electronic states only depend on the nanotube size and its symmetry along the shorter vector direction. In this direction, the wave functions of the original 3m （or 3m/2） periodicity are also suitable for armchair, chiral and zigzag finite CNTs with the C2 （Cs）, C1 and Cn point groups, respectively. Energy gaps present the oscillation with 3m （or 3m/2） or odd-even n. The first principle calculations for some prototype systems are performed. The results are consistent with the theoretical model.

Effects of doping, Stone Wales and vacancy defects on thermal conductivity of single-wall carbon nanotubes

The thermal conductivity of carbon nanotubes with certain defects （doping, Stone-Wales, and vacancy） is investigated by using the non-equilibrium molecular dynamics method. The defective carbon nanotubes （CNTs） are compared with perfect tubes. The influences of type and concentration of the defect, length, diameter, and chirality of the tube, and the ambient temperature are taken into consideration. It is demonstrated that defects result in a dramatic reduction of thermal conductivity. Doping and Stone-Wales （SW） defects have greater effect on armchair tubes, while vacancy affects the zigzag ones more. Thermal conductivity of the nanotubes increases, reaches a peak, and then decreases with increasing temperature. The temperature at which the thermal conductivity peak occurs is dependent on the defect type. Different from SW or vacancy tubes, doped tubes are similar to the perfect ones with a sharp peak at the same temperature. Thermal conductivity goes up when the tube length grows or diameter declines. It seems that the length of thermal conductivity convergence for SW tubes is much shorter than perfect or vacancy ones. The SW or vacancy tubes are less sensitive to the diameter change, compared with perfect ones.

A CONTINUUM MODEL FOR AXIAL-STRAIN-INDUCED TORSION IN SINGLE-WALL CARBON NANOTUBES

Using the atomistic-based finite-deformation shell theory, we analytically investigate the coupling between the axial deformation and the torsion in single-wall carbon nanotubes. We find that the axial-strain-induced torsion（ASIT） response is limited only to chiral nanotubes. This response is affected by chiralities and radii of carbon nanotubes. Our results are similar to that of molecular dynamic simulations reported in the literatures.

Material and structural instabilities of single-wall carbon nanotubes

The nonlinear atomistic interactions usually involve softening behavior. Instability resulting directly from this softening are called the material instability, while those unrelated to this softening are called the structural instability. We use the finite-deformation shell theory based on the interatomic potential to show that the tension instability of single-wall carbon nanotubes is the material instability, while the compression and torsion instabilities are structural instability.

Molecular Dynamics Simulation of Formaldehyde Adsorption and Diffusion in Single-Wall Carbon Nanotube

For gas sensor application,adsorption and diffusion of formaldehyde gas in single-wall carbon nanotube were investigated by using molecular dynamics simulation.The conformations of formaldehyde molecule adsorbed in carbon nanotube were optimized according to principle of minimum energy.The axis of conformation is parallel to the axis of carbon nanotube and about 0.3 nm～0.4 nm away from carbon nanotube wall.The conformation,which is different from that of the formaldehyde molecule in the gas-phase,rotates around carbon nanotube axis.The adsorption energy and diffusivity of formaldehyde molecule in single-wall carbon nanotube is of-56.2 kJ/mol and of 0.2×10^(-4) cm^2/s,respectively.

Simple Method for Preparing Glucose Biosensor Based on Glucose Oxidase in Nanocomposite Material of Single-Wall Carbon Nanotubes/Ionic Liquid

Based on electric conductivity and wide potential window of ionic liquid (IL) and electric property of single-wall car- bon nanotubes (SWCNTs), composite material of IL-SWCNTs was prepared, glucose sensor was built with this mate-rial for immobilizing glucose oxidase (GOx). It showed good response, sensitivity and stability for long time for glu-cose detection. Linear range for the detection of glucose was from 0.5 × 10–6 M to 12 × 10–6 M while detection limit was 6.26 × 10–8 M (S/N = 3).

Pyramid-Textured Antireflective Silicon Surface In Graphene Oxide/Single-Wall Carbon Nanotube–Silicon Heterojunction Solar Cells

Antireflection layers are commonly used in photovoltaics to increase light absorption and therefore increase maximum photocurrent.Here,pyramid structures are created on Si surfaces with alkaline solution etching.The extent of pyramid coverage depends directly on the reaction time and as a result,the surface reflectance decreases with reaction time.

Nickel Decorated Single-Wall Carbon Nanotube as CO Sensor

Based on spin-polarized density functional theory (DFT) calculations, the interaction between nickel cluster decorated single-wall carbon nanotube (CNT) and CO molecule has been investigated. DFT calculations are performed with generalized gradient approximation (GGA) using Perdew-Burke-Ernzerhof (PBE) functional. Interaction of CNT and cluster induces spin polarization in the CNT. Nickel decorated CNT has a large magnetic moment of 4.00 μB which decreases to 0.10 μB when CO molecule is absorbed to it. Such a drastic reduction in magnetization may be detected by SQUID magnetometer. Hence by measuring magnetization change, CNT-cluster system may be used as gas detectors. The charge transfer between the systems has been discussed through Mulliken charge analysis for different orientations of the adsorbed CO molecule. We observed that CNT-cluster system acts as electron donor and CO molecule acts as electron acceptor in this study.

Electrochemical behaviors of lomefloxacin at a single-wall carbon nanotube-modified electrode and its interaction with bovine serum albumin

The electrochemical behaviors of lomefloxacin at a single-wall carbon nanotube-modified glassy carbon electrode have been investigated by cyclic voltammetry.In a Britton-Robinson buffer (pH 4.5),lomefloxacin yields a sensitive and well-defined oxidation peak at ca.1.24 V (vs.SCE) on the modified electrode.Compared with the bare glassy carbon electrode,the oxidation peak current of lomefloxacin significantly increases and the oxidation peak potential positively shifts.Under the optimal conditions,the interaction of lomefloxacin with bovine serum albumin is also investigated.The results indicate that an electrochemically inactive supramolecular complex is formed and the formation of complex between lomefloxacin and bovine serum albumin is an intercalation mechanism.The proposed methods offer a reference for the studies on the biological effects and action mechanism of lomefloxacin with albumins in vivo.

Single-wall carbon nanotube fiber non-woven fabrics with a high electrothermal heating response

Carbon nanotube(CNT)fibers have great promise for constructing multifunctional fabrics with high electrical conductivity,good electro-heating ability,excellent flexibility,and a low density.However,the inter-fiber contacts in the fabric greatly reduce these advantages and limit their application.Herein,a simple pressure-fusing method to fabricate single-wall CNT(SWCNT)fiber non-woven fabrics(NWFs)that are composed of interconnected SWCNT fibers with fused joints is reported,which have good flexibility,a low density of 0.46 g/cm^(3),a high electrical conductivity of 3.7×10^(5)S/m,and a record high specific electrical conductivity of 803(S·m^(2))/kg.They also showed excellent electrical heating ability,so that a temperature of~160℃was rapidly reached at a low voltage of 2 V.Combined with their low density,the SWCNT fiber NWFs are promising for use as a heating unit for low temperature battery protection and de-icing applications.

Plasmon-enhanced ultra-high photoresponse of single-wall carbon nanotube/copper/silicon near-infrared photodetectors

Single wall carbon nanotube(SWCNT)/Si heterojunction photodetectors have the advantages of high photoresponse ability and simple structure,however,their detection wavelength range are usually lower than 1100 nm,which limits their application in the infrared band.We report a SWCNT/Cu/Si photodetector with both a high photoresponse and a detection range up to the infrared band by depositing a Cu nanoparticles(NPs)layer between a SWCNT film and a n-Si substrate.It was found that the Cu NPs produce strong surface plasmon resonance(SPR)under laser irradiation,which breaks through the limitation of Si band gap and greatly improves the photoresponse of the SWCNT/Cu/Si photodetector in the near infrared band.The responsivity(R)of the photodetector in the wavelength range of 1850–1200 nm reached 2.2–14.15 mA/W,which is the highest value in the reported plasmon enhanced n-Si based photodetectors,and about 20,000 times higher than that of a SWCNT/Si photodetector.Its R value for 1550 nm wavelength used in optical communications reached~8.2 mA/W,which is 64%higher than the previously reported values of commonly used photodetectors.We attribute the significant increase to the strong SPR and low Schottky barrier of Cu with n-Si,which facilitates the generation and transfer of the carriers.

Chirality-dependent concentration boundaries of single-wall carbon nanotubes for photoluminescence characterization and applications

Increasing the concentration of single-wall carbon nanotubes(SWCNTs)is an effective method for enhancing their luminescence intensity.However,an increase in the concentration of SWCNTs would inevitably increase their reabsorption effect,degrading their luminescence efficiency.Herein,we systematically investigated variations in the photoluminescence(PL)intensity of(6,5)single-chirality SWCNTs while increasing their concentration.The results show that the PL intensity first increased to a maximum and then decreased with increasing concentration.Numerical analysis indicates that the concentration boundary corresponding to the maximum PL intensity was strongly dependent on the ratio of the optical absorbances of the SWCNTs at their excitation and emission wavelengths.According to this,statistical analysis by experimentally measuring the optical absorption spectra of 18 kinds of single-chirality SWCNTs shows that the concentration boundaries of SWCNTs were dependent upon their Types and diameters.The concentration boundary of Type I SWCNTs was higher than that of Type II SWCNTs,and the concentration boundaries of both Types increased with increasing diameter.These results provide important guidance for spectral characterization and applications in bioimaging and photoelectronic devices.

Tannic acid coated single-wall carbon nanotube membranes for the recovery of Au from trace-level solutions

The efficient recovery of gold from industrial sewage is important for saving precious metals and remains a big challenge.We report the extraction of gold ions from a trace-level aqueous solution using a tannic acid(TA)coated single-wall carbon nanotube(SWCNT)film.The TA has many redox ligands that efficiently adsorb Au(III)from the solution and reduce them to Au particles.The interwoven SWCNTs not only act as a framework to improve the mechanical stability of the hybrid membrane,but also provide abundant paths for H_(2)O transport,and facilitate the full exposure of the TA.As a result,the hybrid membrane has an excellent ability to capture gold ions from solution with a high flux of 157 L/(m^(2)·h·bar),and an ultra-high adsorption capacity of 2095 mg/g from solutions with an extremely low gold concentration of 20 ppm.The adsorbed gold ions are reduced to Au particles,which can be easily collected by oxidation.The recovered Au nanoparticles on the TA–SWCNT hybrid film had a remarkable surface-enhanced Raman scattering effect that enabled the sensitive detection of rhodamine 6G.

Enhancing the Interaction of Carbon Nanotubes by Metal-Organic Decomposition with Improved Mechanical Strength and Ultra-Broadband EMI Shielding Performance

The remarkable properties of carbon nanotubes(CNTs)have led to promising applications in the field of electromagnetic inter-ference(EMI)shielding.However,for macroscopic CNT assemblies,such as CNT film,achieving high electrical and mechanical properties remains challenging,which heavily depends on the tube-tube interac-tions of CNTs.Herein,we develop a novel strategy based on metal-organic decomposition(MOD)to fabricate a flexible silver-carbon nanotube(Ag-CNT)film.The Ag particles are introduced in situ into the CNT film through annealing of MOD,leading to enhanced tube-tube interactions.As a result,the electrical conductivity of Ag-CNT film is up to 6.82×10^(5) S m^(-1),and the EMI shielding effectiveness of Ag-CNT film with a thickness of~7.8μm exceeds 66 dB in the ultra-broad frequency range(3-40 GHz).The tensile strength and Young’s modulus of Ag-CNT film increase from 30.09±3.14 to 76.06±6.20 MPa(~253%)and from 1.12±0.33 to 8.90±0.97 GPa(~795%),respectively.Moreover,the Ag-CNT film exhibits excellent near-field shield-ing performance,which can effectively block wireless transmission.This innovative approach provides an effective route to further apply macroscopic CNT assemblies to future portable and wearable electronic devices.

Heat transfer enhanced inorganic phase change material compositing carbon nanotubes for battery thermal management and thermal runaway propagation mitigation

Developing technologies that can be applied simultaneously in battery thermal management(BTM)and thermal runaway(TR)mitigation is significant to improving the safety of lithium-ion battery systems.Inorganic phase change material(PCM)with nonflammability has the potential to achieve this dual function.This study proposed an encapsulated inorganic phase change material(EPCM)with a heat transfer enhancement for battery systems,where Na_(2)HPO_(4)·12H_(2)O was used as the core PCM encapsulated by silica and the additive of carbon nanotube(CNT)was applied to enhance the thermal conductivity.The microstructure and thermal properties of the EPCM/CNT were analyzed by a series of characterization tests.Two different incorporating methods of CNT were compared and the proper CNT adding amount was also studied.After preparation,the battery thermal management performance and TR propagation mitigation effects of EPCM/CNT were further investigated on the battery modules.The experimental results of thermal management tests showed that EPCM/CNT not only slowed down the temperature rising of the module but also improved the temperature uniformity during normal operation.The peak battery temperature decreased from 76℃to 61.2℃at 2 C discharge rate and the temperature difference was controlled below 3℃.Moreover,the results of TR propagation tests demonstrated that nonflammable EPCM/CNT with good heat absorption could work as a TR barrier,which exhibited effective mitigation on TR and TR propagation.The trigger time of three cells was successfully delayed by 129,474 and 551 s,respectively and the propagation intervals were greatly extended as well.

Extrusion 3D printing of carbon nanotube-assembled carbon aerogel nanocomposites with high electrical conductivity

Carbon nanotubes(CNTs)with high aspect ratio and excellent electrical conduction offer huge functional improvements for current carbon aerogels.However,there remains a major challenge for achieving the on-demand shaping of carbon aerogels with tailored micro-nano structural textures and geometric features.Herein,a facile extrusion 3D printing strategy has been proposed for fabricating CNT-assembled carbon(CNT/C)aerogel nanocomposites through the extrusion printing of pseudoplastic carbomer-based inks,in which the stable dispersion of CNT nanofibers has been achieved relying on the high viscosity of carbomer microgels.After extrusion printing,the chemical solidification through polymerizing RF sols enables 3D-printed aerogel nanocomposites to display high shape fidelity in macroscopic geometries.Benefiting from the micro-nano scale assembly of CNT nanofiber networks and carbon nanoparticle networks in composite phases,3D-printed CNT/C aerogels exhibit enhanced mechanical strength(fracture strength,0.79 MPa)and typical porous structure characteristics,including low density(0.220 g cm^(-3)),high surface area(298.4 m^(2)g^(-1)),and concentrated pore diameter distribution(~32.8nm).More importantly,CNT nanofibers provide an efficient electron transport pathway,imparting 3D-printed CNT/C aerogel composites with a high electrical conductivity of 1.49 S cm^(-1).Our work would offer feasible guidelines for the design and fabrication of shape-dominated functional materials by additive manufacturing.

Hydrodynamic analysis of carbon nanotube clusters in distributor-less conical fluidized beds with step-by-step scaling

As a high-performance material with great application potential,the application of carbon nanotubes has been limited by their production volume.A distributor-less conical fluidized bed is the main equipment used in the industrial production of carbon nanotubes.To improve the production volume and product quality of carbon nanotubes,the study of fluidized-bed-diameter scaling is important.Three different diameters of distributor-less conical fluidized beds were established,and then the particle behavior and bubble characteristics of carbon nanotube clusters at these bed diameters were investigated.Time-series and wavelet analysis methods were used to analyze the pressure-fluctuation signals inside the fluidized beds.Results showed that the distributor-less design caused the airflow to break through the middle of the bed,which did not change with the change in bed diameter.The powder-bridging phenomenon of carbon nanotube clusters in a 100-mm-diameter fluidized bed was related to the special microstructure of carbon nanotube clusters.The frequency of pressure fluctuations in the bed decreased nonlinearly with increasing bed diameter.This study can guide the design and scale-up of distributor-less conical fluidized beds,especially for the scale-up of carbon nanotube production equipment,which can contribute to the improvement of carbon nanotubes’capacity and quality in industrial production.

Carbon nanotube integrated circuit technology:purification,assembly and integration

As the manufacturing process of silicon-based integrated circuits(ICs)approaches its physical limit,the quantum effect of silicon-based field-effect transistors(FETs)has become increasingly evident.And the burgeoning carbon-based semiconductor technology has become one of the most disruptive technologies in the post-Moore era.As one-dimensional nanomaterials,carbon nanotubes(CNTs)are far superior to silicon at the same technology nodes of FETs because of their excellent electrical transport and scaling properties,rendering them the most competitive material in the next-generation ICs technology.However,certain challenges impede the industrialization of CNTs,particularly in terms of material preparation,which significantly hinders the development of CNT-based ICs.Focusing on CNT-based ICs technology,this review summarizes its main technical status,development trends,existing challenges,and future development directions.