The behavior of slender columns under the effect of eccentric loading has always taken the attention of researchers. When investigating the strengthening of reinforced concrete columns, mainly short and circular colum...The behavior of slender columns under the effect of eccentric loading has always taken the attention of researchers. When investigating the strengthening of reinforced concrete columns, mainly short and circular columns are the targeted elements. This is why the data about slender columns with rectangular sections is limited and infrequent specially when loaded eccentrically. This paper aims to increase the available experimental data in this specific area. The experimental program consisted of twenty seven specimens. The specimens were divided into three groups; one control group and two groups strengthened using two strengthening schemes. Scheme 1 implied the use of near surface mounted （NSM） longitudinal steel bars, while in scheme 2, NSM longitudinal steel bars partially wrapped with one ply of carbon fibers reinforced polymers （CFRP） sheets was used. The test specimen had an overall length of 2000 mm and a 100 x 200 mm rectangular cross section. In addition to the strengthening schemes, the test parameters included three ratios for the internal longitudinal steel bars ＂μ＂ 1%, 1.57% and 2.26%. The parameters were extended to cover three stirrups＇ volumetric ratio ＂ρv＂ 0.73%, 0.49% and 0.37%. The specimens were tested under the effect of eccentric loading with eccentricity-to-section height e/h equals 0.25. The research revealed that the strength gain in specimens strengthened with scheme 2 was higher than with scheme 1. Analytical modeling of the stress strain relation of the strengthened RC columns considering the effect of strengthening scheme, internal reinforcement ratio μ, and stirrups＇ volumetric ratio ＂ρv＂ was proposed. Verification was made using available experimental data. The proposed model showed a reasonable agreement with the experimental results.展开更多
Carbon Fiber Reinforced Polymer(CFRP) has such characteristics as light weight, high strength and corrosion resistance, so it is suitable for corrosive environment and large-span structures. This study investigated th...Carbon Fiber Reinforced Polymer(CFRP) has such characteristics as light weight, high strength and corrosion resistance, so it is suitable for corrosive environment and large-span structures. This study investigated the stability of CFRP slender column, whose slenderness is greater than Euler’s critical load. The columns in this study were formed by a two-step process and the fiber direction was along the same direction of column axis. Firstly, we obtained the basic mechanical properties of the material by tensile experiment. Then, we studied the critical force of 10 CFRP columns with different lengths and widths by axial compression test. Finally, by comparing Euler’s formula with the modified Euler formula and combining with existing literature and experimental result of this paper, we proposed a modified Perry formula which could well predict the critical force of unidirectional CFRP extruded column and could be used for CFRP extruded column research and engineering design.展开更多
Aluminum alloys have been widely applied in coastal and marine structures because of their superior sustainability and corrosion resistance.Concrete-filled double-skin aluminum tubular columns(CFDAT)possess higher str...Aluminum alloys have been widely applied in coastal and marine structures because of their superior sustainability and corrosion resistance.Concrete-filled double-skin aluminum tubular columns(CFDAT)possess higher strength and better ductility than traditional reinforced concrete structures.However,few studies have been conducted on numerical simulation methods for circular CFDATs.Specifically,there has been no experimental or numerical study on intermediate-to-slender circular CFDATs.Here,a comprehensive numerical study was conducted on a modeling method for the first time to simulate the axial behavior of a slender circular CFDAT.This study outlines the development of numerical modeling techniques and presents a series of comparative studies using various material nonlinearities,confinement effects,and nonlinearity of the initial geometric imperfections for a slender column.The numerical results were compared with more than 80 previously available stub and slender experimental test results for verification.It was confirmed that the proposed numerical technique was reliable and accurate for simulating the axial behavior of intermediate and slender circular CFDAT.Furthermore,a parametric study was conducted to investigate the effects of geometric and material properties on the axial capacity of the CFDAT.Additionally,the slenderness and strength-to-width ratio of CFDAT were compared with those of concrete-filled double-skin steel tubular columns(CFDST).The simulated axial strengths were compared with those predicted using AS 5100 and AISC 360.New design equations for the CFDATs should be proposed based on AS 5100.展开更多
This paper reports a study based upon experimental investigation which aims to assess the behaviour of reinforced concrete columns strengthened with a new configuration of steel wire mesh as part of ferrocement layer ...This paper reports a study based upon experimental investigation which aims to assess the behaviour of reinforced concrete columns strengthened with a new configuration of steel wire mesh as part of ferrocement layer under the action of axial compression loads. Square and circular small scale columns with three different slenderness ratios of 5, 6.7 and 10 were adopted. A comprehensive experimental progarmme was then running to measure the load capacity and both lateral and vertical displacements. The failure mode was also monitored for each tested case. The results obtained was compared with the reference column samples (without wire mesh) and with some expressions suggested by ACI Code. The experimental results showed that the most influential parameter on the property of load carrying capacity is the slenderness of column. As the slenderness increases, the load capacity clearly decreases. The use of wire mesh enhanced the capability of column to resist the axial loads due to confinement role provided by such material. The maximum percentage increase in load carrying capacity for the modified columns compared with those for the reference samples was 53% for the circular column at slenderness ratio of 10. The critical path of the failure mode was similar for all of the tested columns and normally began from the top or bottom ends, then, in some cases, passed through the middle zone of the column. A suitable expression was suggested to be used for calculating the modulus of elasticity of the tested column based upon the value of load carrying capacity under compression loads.展开更多
文摘The behavior of slender columns under the effect of eccentric loading has always taken the attention of researchers. When investigating the strengthening of reinforced concrete columns, mainly short and circular columns are the targeted elements. This is why the data about slender columns with rectangular sections is limited and infrequent specially when loaded eccentrically. This paper aims to increase the available experimental data in this specific area. The experimental program consisted of twenty seven specimens. The specimens were divided into three groups; one control group and two groups strengthened using two strengthening schemes. Scheme 1 implied the use of near surface mounted （NSM） longitudinal steel bars, while in scheme 2, NSM longitudinal steel bars partially wrapped with one ply of carbon fibers reinforced polymers （CFRP） sheets was used. The test specimen had an overall length of 2000 mm and a 100 x 200 mm rectangular cross section. In addition to the strengthening schemes, the test parameters included three ratios for the internal longitudinal steel bars ＂μ＂ 1%, 1.57% and 2.26%. The parameters were extended to cover three stirrups＇ volumetric ratio ＂ρv＂ 0.73%, 0.49% and 0.37%. The specimens were tested under the effect of eccentric loading with eccentricity-to-section height e/h equals 0.25. The research revealed that the strength gain in specimens strengthened with scheme 2 was higher than with scheme 1. Analytical modeling of the stress strain relation of the strengthened RC columns considering the effect of strengthening scheme, internal reinforcement ratio μ, and stirrups＇ volumetric ratio ＂ρv＂ was proposed. Verification was made using available experimental data. The proposed model showed a reasonable agreement with the experimental results.
基金Sponsored by the Shandong Provincial Natural Science Foundation,China(Grant No.ZR2018MA029)
文摘Carbon Fiber Reinforced Polymer(CFRP) has such characteristics as light weight, high strength and corrosion resistance, so it is suitable for corrosive environment and large-span structures. This study investigated the stability of CFRP slender column, whose slenderness is greater than Euler’s critical load. The columns in this study were formed by a two-step process and the fiber direction was along the same direction of column axis. Firstly, we obtained the basic mechanical properties of the material by tensile experiment. Then, we studied the critical force of 10 CFRP columns with different lengths and widths by axial compression test. Finally, by comparing Euler’s formula with the modified Euler formula and combining with existing literature and experimental result of this paper, we proposed a modified Perry formula which could well predict the critical force of unidirectional CFRP extruded column and could be used for CFRP extruded column research and engineering design.
文摘Aluminum alloys have been widely applied in coastal and marine structures because of their superior sustainability and corrosion resistance.Concrete-filled double-skin aluminum tubular columns(CFDAT)possess higher strength and better ductility than traditional reinforced concrete structures.However,few studies have been conducted on numerical simulation methods for circular CFDATs.Specifically,there has been no experimental or numerical study on intermediate-to-slender circular CFDATs.Here,a comprehensive numerical study was conducted on a modeling method for the first time to simulate the axial behavior of a slender circular CFDAT.This study outlines the development of numerical modeling techniques and presents a series of comparative studies using various material nonlinearities,confinement effects,and nonlinearity of the initial geometric imperfections for a slender column.The numerical results were compared with more than 80 previously available stub and slender experimental test results for verification.It was confirmed that the proposed numerical technique was reliable and accurate for simulating the axial behavior of intermediate and slender circular CFDAT.Furthermore,a parametric study was conducted to investigate the effects of geometric and material properties on the axial capacity of the CFDAT.Additionally,the slenderness and strength-to-width ratio of CFDAT were compared with those of concrete-filled double-skin steel tubular columns(CFDST).The simulated axial strengths were compared with those predicted using AS 5100 and AISC 360.New design equations for the CFDATs should be proposed based on AS 5100.
文摘This paper reports a study based upon experimental investigation which aims to assess the behaviour of reinforced concrete columns strengthened with a new configuration of steel wire mesh as part of ferrocement layer under the action of axial compression loads. Square and circular small scale columns with three different slenderness ratios of 5, 6.7 and 10 were adopted. A comprehensive experimental progarmme was then running to measure the load capacity and both lateral and vertical displacements. The failure mode was also monitored for each tested case. The results obtained was compared with the reference column samples (without wire mesh) and with some expressions suggested by ACI Code. The experimental results showed that the most influential parameter on the property of load carrying capacity is the slenderness of column. As the slenderness increases, the load capacity clearly decreases. The use of wire mesh enhanced the capability of column to resist the axial loads due to confinement role provided by such material. The maximum percentage increase in load carrying capacity for the modified columns compared with those for the reference samples was 53% for the circular column at slenderness ratio of 10. The critical path of the failure mode was similar for all of the tested columns and normally began from the top or bottom ends, then, in some cases, passed through the middle zone of the column. A suitable expression was suggested to be used for calculating the modulus of elasticity of the tested column based upon the value of load carrying capacity under compression loads.
