In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and externa...In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and external rotors are distributed in Halbach array,the inner rotor PMs are equally divided into 3 small pieces,and the outer rotor PMs are equally divided into 2 small pieces.At the same time,the static magnetic modulation ring iron blocks are slotted,each iron block has 3 slots,the width of the slot is 0.4°,and the depth of the single side slot is 1mm.Finally,a two-dimensional model is established,and the eddy current loss and iron loss of the model are optimized,compared with the conventional CMG model,it is found that the changed pattern can increase the internal and external output torque by 4%and 4.12%,respectively.The eddy current loss is reduced by 66.57%,and the iron loss is reduced by 8.9%,which significantly improve the operation efficiency of the CMG.展开更多
To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse importa...To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse important fish habitats in the lower reaches of the Daduhe River in Southwest China.Therefore,a vertical slot fishway(VSF)and a nature-like fishway(NLF)were built near the backwater area of the reservoir to connect the upstream and downstream habitats.Hydrodynamic and aquatic ecological surveys were conducted after the completion of the project to estimate the fish passing effect of the two fishways.The results indicated that both fishways were in effective operation and could maintain the desired hydrodynamic conditions and be used by several local fish species.During the survey,149 fish from 15 species and 111 fish from 17 species were captured by the traps in the VSF and NLF,respectively,while 1263 fish from 27 species were found in the downstream area.Some species captured in the VSF were not found in the NLF,and vice versa,which implied the different preferences of fish.Meanwhile,3789 signals including 2099 upward ones and 1690 downward ones were monitored with an ultrasonic fish detector at the inlet of the VSF.These findings revealed the characteristics of fish species observed in and near the fishways and provided valuable insights into the different fish passing capabilities of VSFandNLF.展开更多
In this study, we examine the hydrodynamic characteristics of three rows of vertical slotted wall breakwaters in which the front and middle walls are permeable and partially immersed in a water channel of constant dep...In this study, we examine the hydrodynamic characteristics of three rows of vertical slotted wall breakwaters in which the front and middle walls are permeable and partially immersed in a water channel of constant depth, whereas the third wall is impermeable. The wave–structure interaction and flow behavior of this type of breakwater arrangement are complicated and must be analyzed before breakwaters can be appropriately designed. To study the hydrodynamic breakwater performance, we developed a mathematical model based on the eigenfunction expansion method and a least squares technique for predicting wave interaction with three rows of vertical slotted wall breakwaters. We theoretically examined the wave transmission, reflection, energy loss, wave runup, and wave force under normal regular waves. Comparisons with experimental measurements show that the mathematical model results adequately reproduce most of the important features. The results of this investigation provide a better understanding of the hydrodynamic performance of triple-row vertical slotted wall breakwaters.展开更多
Valve piezoelectric pumps usually have larger flow rate than that of valveless ones. However, the traditional cantilever valve easily induces stress concentration which impacts the reliability of pumps. Therefore, a c...Valve piezoelectric pumps usually have larger flow rate than that of valveless ones. However, the traditional cantilever valve easily induces stress concentration which impacts the reliability of pumps. Therefore, a cymbal-shaped slotted check valve is proposed to be applied in a piezoelectric pump in order to reduce the stress concentration of the valve and thus improve the reliability of the piezoelectric pump. The structure and working principle of the piezoelectric pump are analyzed; the stress analysis of the cymbal-shaped slotted valve diaphragm is conducted. In addition, finite element software is employed to analyze the difference of the Von-Mises stress between the cymbal-shaped slotted diaphragm and the slotted flat diaphragm. The simulation results show that, the Von-Mises stress of cymbal-shaped slotted diaphragm is smaller than that of the slotted flat one. Furthermore, the cymbal-shaped slotted valve piezoelectric pump is also fabricated, and flow rate experiment is performed. The experimental results indicate that the flow rate of piezoelectric pump working in low frequencies(0 Hz < f< 50 Hz) is larger than that working in high frequencies(200 Hz < f< 2000 Hz). When driven at voltage of 160 V and frequency of 5 Hz, the pump reaches its maximum flow rate of 6.6 g/min. The experimental results validate the feasibility of the cymbal-shaped slotted check valve. This research can effectively solve the problem of stress concentration of valve piezoelectric pumps and is helpful for improving the reliability of them.展开更多
Slotted breakwaters have been used to provide economical protection from waves in harbors where surface waves and currents may co-exist. In this paper, the effects of currents on the wave scattering by slotted breakwa...Slotted breakwaters have been used to provide economical protection from waves in harbors where surface waves and currents may co-exist. In this paper, the effects of currents on the wave scattering by slotted breakwaters are investigated by using a simple model. The model is based on a long wave approximation. The effects of wave height, barrier geometry and current strength on the reflection and transmission coefficients are examined by the model. The model results are compared with recent experimental data. It is found that both the wave-following and wave-opposing currents can increase the reflection coefficient and reduce the transmission coefficient. The model can be used to study the interaction between long waves and slotted breakwaters in coastal waters.展开更多
The adoption of slotted breakwaters can be an ideal option in the protection of very large near-shore floating struc-trees that may extend offshore to a considerable water depth. In this paper, we experimently investi...The adoption of slotted breakwaters can be an ideal option in the protection of very large near-shore floating struc-trees that may extend offshore to a considerable water depth. In this paper, we experimently investigated the behaviour of wave transmission and reflection coefficients of double slotted barriers in the presence of a steady opposing current. The experimental results show that opposing currents have only minor effects on wave reflection, but can significantly reduce the wave transmission through double slotted barriers. The experimental results suggest that coastal currents should be taken into consideration for an economical design of slotted breakwaters.展开更多
A novel slotted helix slow-wave structure (SWS) is proposed to develop a high power, wide-bandwidth, and high reliability millimeter-wave traveling-wave tube (TWT). This novel structure, which has higher heat capa...A novel slotted helix slow-wave structure (SWS) is proposed to develop a high power, wide-bandwidth, and high reliability millimeter-wave traveling-wave tube (TWT). This novel structure, which has higher heat capacity than a conven- tional helix SWS, evolves from conventional helix SWS with three parallel rows of rectangular slots made in the outside of the helix tape. In this paper, the electromagnetic characteristics and the beam-wave interaction of this novel structure operating in the Ka-band are investigated. From our calculations, when the designed beam voltage and beam current are set to be 18.45 kV and 0.2 A, respectively, this novel circuit can produce over 700-W average output power in a frequency range from 27.5 GHz to 32.5 GHz, and the corresponding conversion efficiency values vary from 19% to 21.3%, and the maximum output power is 787 W at 30 GHz.展开更多
A high-voltage transverse pulsed nanosecond discharge with a slotted hollow cathode was found to be a source of high-energy (few kV) ribbon electron beams. Conditions for the formation and extinction of electron bea...A high-voltage transverse pulsed nanosecond discharge with a slotted hollow cathode was found to be a source of high-energy (few kV) ribbon electron beams. Conditions for the formation and extinction of electron beams were experimentally studied in discharges in helium at pressures of 1-100 Torr. It was found that interaction of fast electrons with a non-uniform electric field near the slotted cathode led to limitation of the magnitude of the discharge current. A physical model was developed to describe the discharge current self-limitation that was in satisfactory agreement with the experimental results. Some technical solutions that are expected to increase the upper current limits in transverse nanosecond discharge are discussed.展开更多
In this paper, the analyzing approaches proposed by Zhao Dongfeng, et al.(1997) have been extensively studied. The average cyclic times of the slotted multiple access systems are analyzed by using the average cycle me...In this paper, the analyzing approaches proposed by Zhao Dongfeng, et al.(1997) have been extensively studied. The average cyclic times of the slotted multiple access systems are analyzed by using the average cycle method. Analytic formulae for mean values of a successful period and a colliding period and an idle period are derived. The upper bounds of the system throughput with capture effect and collision resolution are provided. Finally, the simulation results of the slotted multiple access channels are given.展开更多
Fractal antennas are characterized by space filling and self-similarity properties which results in considerable size reduction and multiband operation as compared to conventional microstrip antenna. This paper outlin...Fractal antennas are characterized by space filling and self-similarity properties which results in considerable size reduction and multiband operation as compared to conventional microstrip antenna. This paper outlines a multiband antenna design based on fractal concepts. Fractal antennas show multiband behavior due to self-similarity in their structure. The plus shaped fractal antenna has been designed on a substrate of dielectric constant €r = 4.4 and thickness 1.6mm. The proposed antenna is characterized by a compact size and it is microstrip feed fractal patch of order 1/3. It is observed that the antenna is radiating at multiple resonant frequencies. The resonant frequency is reduced from 2.2 GHz to 900 MHz after I & II iterations respectively. Thus considerable size reduction of 81.77% & overall bandwidth of 12.92% are achieved. The proposed antenna is simulated using the method of moment based commercial software (IE3D) and it is found that simulated results are in good agreement with the experimental results.展开更多
A new technique which is a combination of fractal antenna and array antenna is presented to design Plus Slotted Fractal Antenna Array (PSFAA) in this paper. PSFAA with corporate feed operates at 2.5 GHz frequency. PSF...A new technique which is a combination of fractal antenna and array antenna is presented to design Plus Slotted Fractal Antenna Array (PSFAA) in this paper. PSFAA with corporate feed operates at 2.5 GHz frequency. PSFAA is designed on FR4 substrate material with permittivity 4.4 and height 1.6 mm. PSFAA is designed up to 2nd iteration. High Frequency Structure Simulator (HFSS) software is used for simulation of PSFAA. The proposed antenna array operates at three bands with five frequencies 2.5 GHz, 4.1 GHz, 6.9 GHz, 7.4 GHz and 8.2 GHz. Simulated Return losses results of proposed PSFAA are -22.15 dB, -19.44 dB, -25.21 dB, -10 dB, -12.45 dB at above frequencies respectively. It has a gain of 9.22 dB at resonant frequency 2.5 GHz whereas conventional antenna array has a gain of 5.15 dB at resonant frequency 2.5 GHz. Return losses and gain of PSFAA also improved from conventional antenna array at various resonant frequencies.展开更多
This study investigates the effect of Reynolds number on the performance of Savonius wind turbine with slotted blades.The turbine performance investigation was based on the torque coefficient(Ct),power coefficient(Cp)...This study investigates the effect of Reynolds number on the performance of Savonius wind turbine with slotted blades.The turbine performance investigation was based on the torque coefficient(Ct),power coefficient(Cp),and tip speed ratio(TSR).The experiment used two number of blade configuration,blade overlap ratio of 10%,12.5%and 20%,slotted position of 15%,20%,25%and 35%,and also slotted gap width of 3 mm,5 mm,7 mm,and 9 mm.The wind speed carried out in this experiment are 5.94 m/s,6.46 m/s,6.99 m/s,and 7.27 m/s,which are generated from the fan blowers as a wind source.The Savonius turbine with 10%overlap ratio shows the best performance.The highest Cp obtained is 0.138 by the variation of a 3 mm gap with Re of 1.44×10^(4) and 0.526 TSR.展开更多
The photo-elastic method has been employed to determine stress concentration factor (SCF) for square plates containing holes and inclined slots when the plate edges are subjected to in-plane tension combined with comp...The photo-elastic method has been employed to determine stress concentration factor (SCF) for square plates containing holes and inclined slots when the plate edges are subjected to in-plane tension combined with compression. Analyses given of the isochromatic fringe pattern surrounding the hole provides the SCF conveniently. The model material is calibrated from the known solution to the stress raiser arising from a small circular hole in a plate placed under biaxial tension-compression. These results also compare well with a plane stress FE analysis. Consequently, photo-elasticity has enabled SCF’s to be determined experimentally for a biaxial stress ratio, nominally equal to –4, in plates containing a long, thin slot arranged to be in alignment with each stress axis. The two, principal stresses lying along axes of symmetry in the region surrounding the notch are separated within each isochromatic fringe by the Kuske method [1]. FE provides a comparable full-field view in which contours of maximum shear stress may be identified with the isochromatic fringe pattern directly. The principal stress distributions referred to the plate axes show their maximum concentrations at the notch boundary. Here up to a fourfold magnification occurs in the greater of the two nominal stresses under loads applied to the plate edges. Thus, it is of importance to establish the manner in which the tangential stress is distributed around the slot boundary. Conveniently, it is shown how this distribution is also revealed from an isochro-matic fringe pattern, within which lie the points of maximum tension and maximum compression.展开更多
The interactions between regular surface waves and a surface-pitching slotted barrier are investigated both analytically and experimentally. A quasi-linear theory is developed using the eigenfunction expansion method....The interactions between regular surface waves and a surface-pitching slotted barrier are investigated both analytically and experimentally. A quasi-linear theory is developed using the eigenfunction expansion method. The energy dissipation within the barriers is modeled by a quadratic friction factor, and an equivalent linear dissipation coefficient, which is depth-varying, wave-height dependent, is introduced to linearize the matching condition at the surface-pitching barrier. By comparing the theoretical results with laboratory experiments, it is shown that the present method can satisfactorily predict the variation of the reflection and transmission coefficients with wave height.展开更多
To improve the current understanding of the reduction of tsunami-like solitary wave runup by the pile breakwater on a sloping beach, we developed a 3D numerical wave tank based on the CFD tool OpenFOAM in this study. ...To improve the current understanding of the reduction of tsunami-like solitary wave runup by the pile breakwater on a sloping beach, we developed a 3D numerical wave tank based on the CFD tool OpenFOAM in this study. The Navier Stokes equations were applied to solve the two-phase incompressible flow, combined with an LES model to solve the turbulence and a VOF method to capture the free surface. The adopted model was firstly validated with existing empirical formulas for solitary wave runup on the slope without the pile structure. It is then validated using our new laboratory observations of the free surface elevation, the velocity and the pressure around a row of vertical slotted piles subjected to solitary waves, as well as the wave runup on the slope behind the piles. Subsequently, a set of numerical simulations were implemented to analyze the wave reflection, the wave transmission, and the shoreline runup with various offshore wave heights, offshore water depths, adjacent pile spaces and beach slopes. Finally, an improved empirical equation accounting for the maximum wave runup on the slope was proposed by taking the presence of the pile breakwater into consideration.展开更多
Modeling of the roughness in micro-nano scale and its influence have not been fully investigated, however the roughness will cause amplitude and phase errors of the radiating slot, and decrease the precision and effic...Modeling of the roughness in micro-nano scale and its influence have not been fully investigated, however the roughness will cause amplitude and phase errors of the radiating slot, and decrease the precision and efficiency of the SWA in Ku-band. Firstly, the roughness is simulated using the electromechanical coupled(EC) model. The relationship between roughness and the antenna's radiation properties is obtained. For verification, an antenna proto- type is manufactured and tested, and the simulation method is introduced. According to the prototype, a contrasting experiment dealing with the flatness of the radiating plane is conducted to test the simulation method. The advantage of the EC model is validated by comparisons of the EC model and two classical roughness models (sine wave and fractal function), which shows that the EC model gives a more accurate description model for roughness, the maxi- mum error is 13%. The existence of roughness strongly broadens the beamwidth and raises the side-lobe level of SWA, which is 1.2 times greater than the ideal antenna. In addition, effect of the EC model's evaluation indices is investigated, the most affected scale of the roughness is found, which is 1/10 of the working wavelength. The proposed research provides the instruction for antenna designing and manufacturing.展开更多
After the release of the unlicensed Ultra Wideband (UWB) spectrum 3.1 GHz to 10.6 GHz for the commercial purposes by the Federal Communications Commission (FCC), industries and academia pay much attention due to its p...After the release of the unlicensed Ultra Wideband (UWB) spectrum 3.1 GHz to 10.6 GHz for the commercial purposes by the Federal Communications Commission (FCC), industries and academia pay much attention due to its properties of excellent immunity to multi-path interference, high secured data rate, low power consumption, and simple configuration. The feasible UWB antenna design face some challenges including the ultra wide impedance matching, omni directional radiation pattern, constant gain, high radiation efficiency, low profile, compact antenna size and easy manufacturing. since the CPW fed planar slot antennas have the advantages of wide bandwidth, simple structure, less radiation loss, low cost and easy integration of monolithic microwave integrated circuits (MMIC). In general two parameters affect planar slot antennas impedance bandwidth, the slot width and feed structure. CPW-Fed Slot Antenna with Triangular Tuning Stub, the slot shape could be bow-tie slot, wide rectangular slot, circular slot and hexagonal slot. The impedance tuning can also be performed by using coupling techniques like inductively and capacitively coupled slots, dielectric resonator coupling and other techniques such as using photonic band gap (PGB). Using these techniques, large impedance bandwidth could be obtained but they are quite complicated. Planar slot antennas have two parameters that affect impedance bandwidth, the slot width and the feed structure. The optimum feed structure gives the good impedance matching and the wider slot gives more bandwidth. The proposed antenna in this paper is designed with a compact rectangular slot and a rectangular spiral feeding structure at the interior portion of the feed. The antenna is cleft and slotted at the edge and the effects is studied. The antenna only one of its kinds in structure, small in size and simple design due to less number of design parameters compared with the existing ultra wideband antennas in the literature. The bandwidth, gain, directivity and other antenna parameters are at acceptable level. IE3D method of moments based simulation software is used for this analysis. The proposed antenna design and its experimental result details is presented and discussed.展开更多
基金supported in part by National Natural Science Foundation of China and China Postdoctoral Science Foundation.(Project No.51707072,2018M632855).
文摘In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and external rotors are distributed in Halbach array,the inner rotor PMs are equally divided into 3 small pieces,and the outer rotor PMs are equally divided into 2 small pieces.At the same time,the static magnetic modulation ring iron blocks are slotted,each iron block has 3 slots,the width of the slot is 0.4°,and the depth of the single side slot is 1mm.Finally,a two-dimensional model is established,and the eddy current loss and iron loss of the model are optimized,compared with the conventional CMG model,it is found that the changed pattern can increase the internal and external output torque by 4%and 4.12%,respectively.The eddy current loss is reduced by 66.57%,and the iron loss is reduced by 8.9%,which significantly improve the operation efficiency of the CMG.
基金supported by the National Outstanding Youth Science Fund Project of the National Natural Science Foundation of China(Grant No.51922065)the National Natural Science Foundation of China(Grant No.52179070)the Open Research Fund of Hubei International Science and Technology Cooperation Base of Fish Passage(Grant No.HIBF2020007).
文摘To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse important fish habitats in the lower reaches of the Daduhe River in Southwest China.Therefore,a vertical slot fishway(VSF)and a nature-like fishway(NLF)were built near the backwater area of the reservoir to connect the upstream and downstream habitats.Hydrodynamic and aquatic ecological surveys were conducted after the completion of the project to estimate the fish passing effect of the two fishways.The results indicated that both fishways were in effective operation and could maintain the desired hydrodynamic conditions and be used by several local fish species.During the survey,149 fish from 15 species and 111 fish from 17 species were captured by the traps in the VSF and NLF,respectively,while 1263 fish from 27 species were found in the downstream area.Some species captured in the VSF were not found in the NLF,and vice versa,which implied the different preferences of fish.Meanwhile,3789 signals including 2099 upward ones and 1690 downward ones were monitored with an ultrasonic fish detector at the inlet of the VSF.These findings revealed the characteristics of fish species observed in and near the fishways and provided valuable insights into the different fish passing capabilities of VSFandNLF.
基金King Abdul-Aziz City for Science and Technology,General Directorate of Research Grants Programs(LGP-35-287)
文摘In this study, we examine the hydrodynamic characteristics of three rows of vertical slotted wall breakwaters in which the front and middle walls are permeable and partially immersed in a water channel of constant depth, whereas the third wall is impermeable. The wave–structure interaction and flow behavior of this type of breakwater arrangement are complicated and must be analyzed before breakwaters can be appropriately designed. To study the hydrodynamic breakwater performance, we developed a mathematical model based on the eigenfunction expansion method and a least squares technique for predicting wave interaction with three rows of vertical slotted wall breakwaters. We theoretically examined the wave transmission, reflection, energy loss, wave runup, and wave force under normal regular waves. Comparisons with experimental measurements show that the mathematical model results adequately reproduce most of the important features. The results of this investigation provide a better understanding of the hydrodynamic performance of triple-row vertical slotted wall breakwaters.
基金Supported by National Natural Science Foundation of China(Grant No.51605200)Jiangsu Provincial Natural Science Foundation of China (Grant No.BK20150518)+1 种基金Jiangsu Provincial Postdoctoral Science Foundation of China (Grant No.1501108B)Senior Talent Start-up Foundation of Jiangsu University(Grant No.14JDG145)
文摘Valve piezoelectric pumps usually have larger flow rate than that of valveless ones. However, the traditional cantilever valve easily induces stress concentration which impacts the reliability of pumps. Therefore, a cymbal-shaped slotted check valve is proposed to be applied in a piezoelectric pump in order to reduce the stress concentration of the valve and thus improve the reliability of the piezoelectric pump. The structure and working principle of the piezoelectric pump are analyzed; the stress analysis of the cymbal-shaped slotted valve diaphragm is conducted. In addition, finite element software is employed to analyze the difference of the Von-Mises stress between the cymbal-shaped slotted diaphragm and the slotted flat diaphragm. The simulation results show that, the Von-Mises stress of cymbal-shaped slotted diaphragm is smaller than that of the slotted flat one. Furthermore, the cymbal-shaped slotted valve piezoelectric pump is also fabricated, and flow rate experiment is performed. The experimental results indicate that the flow rate of piezoelectric pump working in low frequencies(0 Hz < f< 50 Hz) is larger than that working in high frequencies(200 Hz < f< 2000 Hz). When driven at voltage of 160 V and frequency of 5 Hz, the pump reaches its maximum flow rate of 6.6 g/min. The experimental results validate the feasibility of the cymbal-shaped slotted check valve. This research can effectively solve the problem of stress concentration of valve piezoelectric pumps and is helpful for improving the reliability of them.
基金The project partially supported by the Hong Kong Research Grant Council under Grant NoHKUST-DAG03/04.EG39 and HKUST6227/04E.
文摘Slotted breakwaters have been used to provide economical protection from waves in harbors where surface waves and currents may co-exist. In this paper, the effects of currents on the wave scattering by slotted breakwaters are investigated by using a simple model. The model is based on a long wave approximation. The effects of wave height, barrier geometry and current strength on the reflection and transmission coefficients are examined by the model. The model results are compared with recent experimental data. It is found that both the wave-following and wave-opposing currents can increase the reflection coefficient and reduce the transmission coefficient. The model can be used to study the interaction between long waves and slotted breakwaters in coastal waters.
基金The work was partially supported bythe Nanyang Technological University,Singapore(Grant No.SUG03/07)partially supported by RGC,Hong Kong,China(Grant No.DAG03/04.EG39)
文摘The adoption of slotted breakwaters can be an ideal option in the protection of very large near-shore floating struc-trees that may extend offshore to a considerable water depth. In this paper, we experimently investigated the behaviour of wave transmission and reflection coefficients of double slotted barriers in the presence of a steady opposing current. The experimental results show that opposing currents have only minor effects on wave reflection, but can significantly reduce the wave transmission through double slotted barriers. The experimental results suggest that coastal currents should be taken into consideration for an economical design of slotted breakwaters.
基金Project supported by the National Natural Science Foundation of China(Grant No.61271029)the Natural Science Key Laboratory Foundationthe Natural Science Fund for Distinguished Young Scholars of China(Grant No.61125103)
文摘A novel slotted helix slow-wave structure (SWS) is proposed to develop a high power, wide-bandwidth, and high reliability millimeter-wave traveling-wave tube (TWT). This novel structure, which has higher heat capacity than a conven- tional helix SWS, evolves from conventional helix SWS with three parallel rows of rectangular slots made in the outside of the helix tape. In this paper, the electromagnetic characteristics and the beam-wave interaction of this novel structure operating in the Ka-band are investigated. From our calculations, when the designed beam voltage and beam current are set to be 18.45 kV and 0.2 A, respectively, this novel circuit can produce over 700-W average output power in a frequency range from 27.5 GHz to 32.5 GHz, and the corresponding conversion efficiency values vary from 19% to 21.3%, and the maximum output power is 787 W at 30 GHz.
基金financially supported by the project part of the state assignment of the Ministry of Education and Science of Russia in scientific activities,project 3.1262.2014K
文摘A high-voltage transverse pulsed nanosecond discharge with a slotted hollow cathode was found to be a source of high-energy (few kV) ribbon electron beams. Conditions for the formation and extinction of electron beams were experimentally studied in discharges in helium at pressures of 1-100 Torr. It was found that interaction of fast electrons with a non-uniform electric field near the slotted cathode led to limitation of the magnitude of the discharge current. A physical model was developed to describe the discharge current self-limitation that was in satisfactory agreement with the experimental results. Some technical solutions that are expected to increase the upper current limits in transverse nanosecond discharge are discussed.
文摘In this paper, the analyzing approaches proposed by Zhao Dongfeng, et al.(1997) have been extensively studied. The average cyclic times of the slotted multiple access systems are analyzed by using the average cycle method. Analytic formulae for mean values of a successful period and a colliding period and an idle period are derived. The upper bounds of the system throughput with capture effect and collision resolution are provided. Finally, the simulation results of the slotted multiple access channels are given.
文摘Fractal antennas are characterized by space filling and self-similarity properties which results in considerable size reduction and multiband operation as compared to conventional microstrip antenna. This paper outlines a multiband antenna design based on fractal concepts. Fractal antennas show multiband behavior due to self-similarity in their structure. The plus shaped fractal antenna has been designed on a substrate of dielectric constant €r = 4.4 and thickness 1.6mm. The proposed antenna is characterized by a compact size and it is microstrip feed fractal patch of order 1/3. It is observed that the antenna is radiating at multiple resonant frequencies. The resonant frequency is reduced from 2.2 GHz to 900 MHz after I & II iterations respectively. Thus considerable size reduction of 81.77% & overall bandwidth of 12.92% are achieved. The proposed antenna is simulated using the method of moment based commercial software (IE3D) and it is found that simulated results are in good agreement with the experimental results.
文摘A new technique which is a combination of fractal antenna and array antenna is presented to design Plus Slotted Fractal Antenna Array (PSFAA) in this paper. PSFAA with corporate feed operates at 2.5 GHz frequency. PSFAA is designed on FR4 substrate material with permittivity 4.4 and height 1.6 mm. PSFAA is designed up to 2nd iteration. High Frequency Structure Simulator (HFSS) software is used for simulation of PSFAA. The proposed antenna array operates at three bands with five frequencies 2.5 GHz, 4.1 GHz, 6.9 GHz, 7.4 GHz and 8.2 GHz. Simulated Return losses results of proposed PSFAA are -22.15 dB, -19.44 dB, -25.21 dB, -10 dB, -12.45 dB at above frequencies respectively. It has a gain of 9.22 dB at resonant frequency 2.5 GHz whereas conventional antenna array has a gain of 5.15 dB at resonant frequency 2.5 GHz. Return losses and gain of PSFAA also improved from conventional antenna array at various resonant frequencies.
基金This research was funded by Universitas Sebelas Maret,grant of PNBP with contract number 452/UN27.21/PN/2020.
文摘This study investigates the effect of Reynolds number on the performance of Savonius wind turbine with slotted blades.The turbine performance investigation was based on the torque coefficient(Ct),power coefficient(Cp),and tip speed ratio(TSR).The experiment used two number of blade configuration,blade overlap ratio of 10%,12.5%and 20%,slotted position of 15%,20%,25%and 35%,and also slotted gap width of 3 mm,5 mm,7 mm,and 9 mm.The wind speed carried out in this experiment are 5.94 m/s,6.46 m/s,6.99 m/s,and 7.27 m/s,which are generated from the fan blowers as a wind source.The Savonius turbine with 10%overlap ratio shows the best performance.The highest Cp obtained is 0.138 by the variation of a 3 mm gap with Re of 1.44×10^(4) and 0.526 TSR.
文摘The photo-elastic method has been employed to determine stress concentration factor (SCF) for square plates containing holes and inclined slots when the plate edges are subjected to in-plane tension combined with compression. Analyses given of the isochromatic fringe pattern surrounding the hole provides the SCF conveniently. The model material is calibrated from the known solution to the stress raiser arising from a small circular hole in a plate placed under biaxial tension-compression. These results also compare well with a plane stress FE analysis. Consequently, photo-elasticity has enabled SCF’s to be determined experimentally for a biaxial stress ratio, nominally equal to –4, in plates containing a long, thin slot arranged to be in alignment with each stress axis. The two, principal stresses lying along axes of symmetry in the region surrounding the notch are separated within each isochromatic fringe by the Kuske method [1]. FE provides a comparable full-field view in which contours of maximum shear stress may be identified with the isochromatic fringe pattern directly. The principal stress distributions referred to the plate axes show their maximum concentrations at the notch boundary. Here up to a fourfold magnification occurs in the greater of the two nominal stresses under loads applied to the plate edges. Thus, it is of importance to establish the manner in which the tangential stress is distributed around the slot boundary. Conveniently, it is shown how this distribution is also revealed from an isochro-matic fringe pattern, within which lie the points of maximum tension and maximum compression.
文摘The interactions between regular surface waves and a surface-pitching slotted barrier are investigated both analytically and experimentally. A quasi-linear theory is developed using the eigenfunction expansion method. The energy dissipation within the barriers is modeled by a quadratic friction factor, and an equivalent linear dissipation coefficient, which is depth-varying, wave-height dependent, is introduced to linearize the matching condition at the surface-pitching barrier. By comparing the theoretical results with laboratory experiments, it is shown that the present method can satisfactorily predict the variation of the reflection and transmission coefficients with wave height.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51679014 and 51839002)the Hunan Science and Technology Plan Program(Grant No.2017RS3035)the Open Foundation of Key Laboratory of Key Technology on Hydropower Development of Hunan Province(Grant No.PKLHD201706)
文摘To improve the current understanding of the reduction of tsunami-like solitary wave runup by the pile breakwater on a sloping beach, we developed a 3D numerical wave tank based on the CFD tool OpenFOAM in this study. The Navier Stokes equations were applied to solve the two-phase incompressible flow, combined with an LES model to solve the turbulence and a VOF method to capture the free surface. The adopted model was firstly validated with existing empirical formulas for solitary wave runup on the slope without the pile structure. It is then validated using our new laboratory observations of the free surface elevation, the velocity and the pressure around a row of vertical slotted piles subjected to solitary waves, as well as the wave runup on the slope behind the piles. Subsequently, a set of numerical simulations were implemented to analyze the wave reflection, the wave transmission, and the shoreline runup with various offshore wave heights, offshore water depths, adjacent pile spaces and beach slopes. Finally, an improved empirical equation accounting for the maximum wave runup on the slope was proposed by taking the presence of the pile breakwater into consideration.
基金Supported by National Natural Science Foundation of China(Grant Nos.51305322,51405364,51475348)
文摘Modeling of the roughness in micro-nano scale and its influence have not been fully investigated, however the roughness will cause amplitude and phase errors of the radiating slot, and decrease the precision and efficiency of the SWA in Ku-band. Firstly, the roughness is simulated using the electromechanical coupled(EC) model. The relationship between roughness and the antenna's radiation properties is obtained. For verification, an antenna proto- type is manufactured and tested, and the simulation method is introduced. According to the prototype, a contrasting experiment dealing with the flatness of the radiating plane is conducted to test the simulation method. The advantage of the EC model is validated by comparisons of the EC model and two classical roughness models (sine wave and fractal function), which shows that the EC model gives a more accurate description model for roughness, the maxi- mum error is 13%. The existence of roughness strongly broadens the beamwidth and raises the side-lobe level of SWA, which is 1.2 times greater than the ideal antenna. In addition, effect of the EC model's evaluation indices is investigated, the most affected scale of the roughness is found, which is 1/10 of the working wavelength. The proposed research provides the instruction for antenna designing and manufacturing.
文摘After the release of the unlicensed Ultra Wideband (UWB) spectrum 3.1 GHz to 10.6 GHz for the commercial purposes by the Federal Communications Commission (FCC), industries and academia pay much attention due to its properties of excellent immunity to multi-path interference, high secured data rate, low power consumption, and simple configuration. The feasible UWB antenna design face some challenges including the ultra wide impedance matching, omni directional radiation pattern, constant gain, high radiation efficiency, low profile, compact antenna size and easy manufacturing. since the CPW fed planar slot antennas have the advantages of wide bandwidth, simple structure, less radiation loss, low cost and easy integration of monolithic microwave integrated circuits (MMIC). In general two parameters affect planar slot antennas impedance bandwidth, the slot width and feed structure. CPW-Fed Slot Antenna with Triangular Tuning Stub, the slot shape could be bow-tie slot, wide rectangular slot, circular slot and hexagonal slot. The impedance tuning can also be performed by using coupling techniques like inductively and capacitively coupled slots, dielectric resonator coupling and other techniques such as using photonic band gap (PGB). Using these techniques, large impedance bandwidth could be obtained but they are quite complicated. Planar slot antennas have two parameters that affect impedance bandwidth, the slot width and the feed structure. The optimum feed structure gives the good impedance matching and the wider slot gives more bandwidth. The proposed antenna in this paper is designed with a compact rectangular slot and a rectangular spiral feeding structure at the interior portion of the feed. The antenna is cleft and slotted at the edge and the effects is studied. The antenna only one of its kinds in structure, small in size and simple design due to less number of design parameters compared with the existing ultra wideband antennas in the literature. The bandwidth, gain, directivity and other antenna parameters are at acceptable level. IE3D method of moments based simulation software is used for this analysis. The proposed antenna design and its experimental result details is presented and discussed.