High ionic conductivity and superior interfacial stability of solid electrolytes at the electrodes are crucial factors for high-performance all-solid-state sodium batteries. Herein, a composite solid electrolyte Na3PS...High ionic conductivity and superior interfacial stability of solid electrolytes at the electrodes are crucial factors for high-performance all-solid-state sodium batteries. Herein, a composite solid electrolyte Na3PS4-polyethylene oxide is synthesized by the solution-phase reaction method with an improved ionic conductivity up to 9.4 × 10-5 S/cm at room temperature. Moreover, polyethylene oxide polymer layer is wrapped homogeneously on the surface of Na3PS4 particles, which could effectively avoid the direct contact between Na3PS4 electrolyte and sodium metal, thus alleviate their side reactions. We demonstrate that all-solid-state battery SnS2/Na with the composite solid electrolyte Na3PS4-polyethylene oxide delivers an enhanced electrochemical performance with 230 m Ah/g after 40 cycles.展开更多
Photocatalytic method has been intensively explored for Cr(VI)reduction owing to its efficient and environmentally friendly natures.In order to obtain a high efficiency in practical application,efficient photocatalyst...Photocatalytic method has been intensively explored for Cr(VI)reduction owing to its efficient and environmentally friendly natures.In order to obtain a high efficiency in practical application,efficient photocatalysts need to be developed.Here,ZnIn2S4/SnS2 with a three-dimensional(3D)heterostructure was prepared by a hydrothermal method and its photocatalytic performance in Cr(VI)reduction was investigated.When the mass ratio of SnS2 to ZnIn2S4 is 1:10,the ZnIn2S4/SnS2 composite exhibits the highest photocatalytic activity with 100%efficiency for Cr(VI)(50 mg/L)reduction within 70 min under visible-light irradiation,which is much higher than those of pure ZnIn2S4 and SnS2.The enhanced charge separation and the light absorption have been confirmed from the photoluminescence and UV-vis absorption spectra to be the two reasons for the increased activity towards photocatalytic Cr(VI)reduction.In addition,after three cycles of testing,no obvious degradation is observed with the 3D heterostructured ZnIn2S4/SnS2,which maintains a good photocatalytic stability.展开更多
Generally,the practical capacity of an electrode should include the weight of non-active components such as current collector,polymer binder,and conductive additives,which were as high as 70 wt%in current reported wor...Generally,the practical capacity of an electrode should include the weight of non-active components such as current collector,polymer binder,and conductive additives,which were as high as 70 wt%in current reported works,seriously limiting the practical capacity.This work pioneered the usage of ultralight reduced graphene fiber(rGF)fabrics as conductive scaffolds,aiming to reduce the weight of nonactive components and enhance the practical capacity.Ultrathin SnS2 nanosheets/rGF hybrids were prepared and used as binder-free electrodes of sodium-ion batteries(SIBs).The interfused graphene fibers endow the electrode a porous,continuous,and conductive network.The in situ phase transformation from SnO2 to SnS2 could preserve the strong interfacial interactions between SnS2 and graphene.Benefitting from these,the designed binder-free electrode delivers a high specific capacity of 500 mAh g?1 after 500 cycles at a current rate of 0.5 A g?1 with almost 100%Coulombic efficiency.Furthermore,the weight percentage of SnS2 in the whole electrode could reach up to 67.2 wt%,much higher than that of common electrode configurations using Cu foil,Al foil,or carbon cloth,significantly highlighting the ultralight characters and advantages of the rGF fabrics for using as binder-free electrodes of SIBs.展开更多
Heterostructure photocatalysts with a built-in electric field have become one of the most promising strategies to enhance photogenerated electron-hole pair separation. However, close contact between the two active com...Heterostructure photocatalysts with a built-in electric field have become one of the most promising strategies to enhance photogenerated electron-hole pair separation. However, close contact between the two active components of heterogeneous photocatalysts remains a problem. Herein, the in-situ fabrication of an SnO2/SnS2 heterostructure photocatalyst was performed;the structure showed enhanced photocatalytic performance resulting from the tight-contact heterostructures. The results of photoelectrochemical measurements further verified that a tight-contact heterostructure improved the separation of photogenerated electron-hole pairs. The results of EIS Bode plots also demonstrated that such in-situ fabricated SnO2/SnS2 samples exhibited the longest carrier lifetime(41.6 μs) owing to the intimate interface of SnO2/SnS2 heterostructures.展开更多
Doping, which is the intentional introducti on of impurities into a material, can improve the metal-semiconductor interface by reducing Schottky barrier width. Here, we prese nt high-quality two-dime nsional SnS2 nano...Doping, which is the intentional introducti on of impurities into a material, can improve the metal-semiconductor interface by reducing Schottky barrier width. Here, we prese nt high-quality two-dime nsional SnS2 nano sheets with well-controlled Sb dopi ng concen tration via direct vapor growth approach and following micromechanical cleavage process. X-ray photoelectro n spectroscopy (XPS) measureme nt dem on strates that Sb contents of the doped samples are approximately 0.22%, 0.34% and 1.21%, respectively, and doping in duces the upward shift of the Fermi level with respect to the pristi ne SnS2. Tran smissio n electro n microscopy (TEM) characterizatio n exhibits that Sb-doped SnS2 nano sheets have a high-quality hexagonal symmetry structure and Sb element is uniformly distributed in the nano sheets. The phototra nsistors based on the Sb-doped SnS2 mono layers show n-type behavior with high mobility which is one order of magn itude higher than that of pristi ne SnS2 phototra nsistors. The photorespo nsivity and exter nal quantum efficiency (EQE) of Sb-S nS2 mono layers phototra nsistors are approximately three orders of magnitude higher than that of pristine SnS2 phototransistor. The results suggest that the method of reducing Shottky barrier width to achieve high mobility and photoresp on sivity is effective, and Sb-doped SnS2 mono layer has significant potential in future nanoelectronic and optoelectronic applications.展开更多
The severe bulk recombination and sluggish oxygen evolution reaction(OER)dynamics of photoanodes severely restrict the application of photoelectrochemical(PEC)devices.To solve these two problems,crystallographic facet...The severe bulk recombination and sluggish oxygen evolution reaction(OER)dynamics of photoanodes severely restrict the application of photoelectrochemical(PEC)devices.To solve these two problems,crystallographic facet orientation and cocatalyst emergence with a high-quality photoanode/cocatalyst interface were realized through an air annealing-assisted strategy to treat atomic layer deposition(ALD)-modified SnSnanosheet arrays.Based on experimental observations and theoretical calculations,the reduced(001)crystal facet of SnSdecreases the recombination of photogenerated carriers in the bulk and improves the carrier separation of the photoanode.Moreover,the unexpectedly formed ZnTiOSfilm decreases the overpotential of the surface OER,reduces interface recombination,and extends the carrier lifetime.These synergistic effects lead to significantly enhanced PEC performance,with a high photocurrent density of 1.97 mA cm^(-2)at 1.23 V vs.reversible hydrogen electrode(RHE)and a low onset potential of 0.21 V vs.RHE,which are superior to reported mostly SnS-based photoanodes.展开更多
基金funding support from 1000 Talent Plan program(NO.31370086963030)research projects from Shandong Province(2018JMRH0211,2017CXGC1010 and 2016GGX104001)+2 种基金Taishan Scholar Program(11370085961006)the National Science Foundation of Shandong Province(ZR2017MEM002)the Fundamental Research Funds of Shandong University(201810422046,2017JC010,2017JC042,and 2016JC005)。
文摘High ionic conductivity and superior interfacial stability of solid electrolytes at the electrodes are crucial factors for high-performance all-solid-state sodium batteries. Herein, a composite solid electrolyte Na3PS4-polyethylene oxide is synthesized by the solution-phase reaction method with an improved ionic conductivity up to 9.4 × 10-5 S/cm at room temperature. Moreover, polyethylene oxide polymer layer is wrapped homogeneously on the surface of Na3PS4 particles, which could effectively avoid the direct contact between Na3PS4 electrolyte and sodium metal, thus alleviate their side reactions. We demonstrate that all-solid-state battery SnS2/Na with the composite solid electrolyte Na3PS4-polyethylene oxide delivers an enhanced electrochemical performance with 230 m Ah/g after 40 cycles.
基金the support of the National Natural Science Foundation of China (51702087 and 21673066)~~
文摘Photocatalytic method has been intensively explored for Cr(VI)reduction owing to its efficient and environmentally friendly natures.In order to obtain a high efficiency in practical application,efficient photocatalysts need to be developed.Here,ZnIn2S4/SnS2 with a three-dimensional(3D)heterostructure was prepared by a hydrothermal method and its photocatalytic performance in Cr(VI)reduction was investigated.When the mass ratio of SnS2 to ZnIn2S4 is 1:10,the ZnIn2S4/SnS2 composite exhibits the highest photocatalytic activity with 100%efficiency for Cr(VI)(50 mg/L)reduction within 70 min under visible-light irradiation,which is much higher than those of pure ZnIn2S4 and SnS2.The enhanced charge separation and the light absorption have been confirmed from the photoluminescence and UV-vis absorption spectra to be the two reasons for the increased activity towards photocatalytic Cr(VI)reduction.In addition,after three cycles of testing,no obvious degradation is observed with the 3D heterostructured ZnIn2S4/SnS2,which maintains a good photocatalytic stability.
基金financially supported by the National Natural Science Foundation of China(Nos.21503025,21503178 and 21603019)Fundamental Research Funds for the Central Universities(Nos.0903005203377 and 106112016CDJZR325520)+3 种基金Key Program for International Science and Technology Cooperation Projects of Ministry of Science and Technology of China(No.2016YFE0125900)Venture and Innovation Support Program for Chongqing Overseas Returnees(cx2017060 and cx2017115)Chongqing Research Program of Basic Research and Frontier Technology(No.cstc2016jcyjA1059)Hundred Talents Program of Chongqing University.
文摘Generally,the practical capacity of an electrode should include the weight of non-active components such as current collector,polymer binder,and conductive additives,which were as high as 70 wt%in current reported works,seriously limiting the practical capacity.This work pioneered the usage of ultralight reduced graphene fiber(rGF)fabrics as conductive scaffolds,aiming to reduce the weight of nonactive components and enhance the practical capacity.Ultrathin SnS2 nanosheets/rGF hybrids were prepared and used as binder-free electrodes of sodium-ion batteries(SIBs).The interfused graphene fibers endow the electrode a porous,continuous,and conductive network.The in situ phase transformation from SnO2 to SnS2 could preserve the strong interfacial interactions between SnS2 and graphene.Benefitting from these,the designed binder-free electrode delivers a high specific capacity of 500 mAh g?1 after 500 cycles at a current rate of 0.5 A g?1 with almost 100%Coulombic efficiency.Furthermore,the weight percentage of SnS2 in the whole electrode could reach up to 67.2 wt%,much higher than that of common electrode configurations using Cu foil,Al foil,or carbon cloth,significantly highlighting the ultralight characters and advantages of the rGF fabrics for using as binder-free electrodes of SIBs.
文摘Heterostructure photocatalysts with a built-in electric field have become one of the most promising strategies to enhance photogenerated electron-hole pair separation. However, close contact between the two active components of heterogeneous photocatalysts remains a problem. Herein, the in-situ fabrication of an SnO2/SnS2 heterostructure photocatalyst was performed;the structure showed enhanced photocatalytic performance resulting from the tight-contact heterostructures. The results of photoelectrochemical measurements further verified that a tight-contact heterostructure improved the separation of photogenerated electron-hole pairs. The results of EIS Bode plots also demonstrated that such in-situ fabricated SnO2/SnS2 samples exhibited the longest carrier lifetime(41.6 μs) owing to the intimate interface of SnO2/SnS2 heterostructures.
基金the National Natural Science Foundation of China (Nos. 61804050, 51872086, 61622406, 11674310, and 61571415)the Double First-Class Initiative of Hunan University (No. 531109100004)the Fundamental Research Funds of the Central Universities (Nos. 531107051078 and 531107051055).
文摘Doping, which is the intentional introducti on of impurities into a material, can improve the metal-semiconductor interface by reducing Schottky barrier width. Here, we prese nt high-quality two-dime nsional SnS2 nano sheets with well-controlled Sb dopi ng concen tration via direct vapor growth approach and following micromechanical cleavage process. X-ray photoelectro n spectroscopy (XPS) measureme nt dem on strates that Sb contents of the doped samples are approximately 0.22%, 0.34% and 1.21%, respectively, and doping in duces the upward shift of the Fermi level with respect to the pristi ne SnS2. Tran smissio n electro n microscopy (TEM) characterizatio n exhibits that Sb-doped SnS2 nano sheets have a high-quality hexagonal symmetry structure and Sb element is uniformly distributed in the nano sheets. The phototra nsistors based on the Sb-doped SnS2 mono layers show n-type behavior with high mobility which is one order of magn itude higher than that of pristi ne SnS2 phototra nsistors. The photorespo nsivity and exter nal quantum efficiency (EQE) of Sb-S nS2 mono layers phototra nsistors are approximately three orders of magnitude higher than that of pristine SnS2 phototransistor. The results suggest that the method of reducing Shottky barrier width to achieve high mobility and photoresp on sivity is effective, and Sb-doped SnS2 mono layer has significant potential in future nanoelectronic and optoelectronic applications.
基金support from the National Key Research and Development Program of China(2021YFA1500800)the National Natural Science Foundation of China(52025028)+1 种基金the Priority Academic Program Development(PAPD)of Jiangsu Higher Education Institutionssupport of the National Natural Science Foundation of China(21973006)。
文摘The severe bulk recombination and sluggish oxygen evolution reaction(OER)dynamics of photoanodes severely restrict the application of photoelectrochemical(PEC)devices.To solve these two problems,crystallographic facet orientation and cocatalyst emergence with a high-quality photoanode/cocatalyst interface were realized through an air annealing-assisted strategy to treat atomic layer deposition(ALD)-modified SnSnanosheet arrays.Based on experimental observations and theoretical calculations,the reduced(001)crystal facet of SnSdecreases the recombination of photogenerated carriers in the bulk and improves the carrier separation of the photoanode.Moreover,the unexpectedly formed ZnTiOSfilm decreases the overpotential of the surface OER,reduces interface recombination,and extends the carrier lifetime.These synergistic effects lead to significantly enhanced PEC performance,with a high photocurrent density of 1.97 mA cm^(-2)at 1.23 V vs.reversible hydrogen electrode(RHE)and a low onset potential of 0.21 V vs.RHE,which are superior to reported mostly SnS-based photoanodes.
