Influences affecting the soil-water characteristic curve

The soil-water characteristic curve (SWCC) is the primary partially saturated soil information as its behavior and properties can be derived from it. Although there have been many studies of unsaturated soils and the SWCC, there is still no combined constitutive model that can simulate soil characteristics accurately. In cases when hydraulic hysteresis is dominant (e.g. under cyclic loading) it is particularly important to use the SWCC. In the past decades, several mathematical expressions have been proposed to model the curve. There are various influences on the SWCC as a source of information, so the curves obtained from conventional tests often cannot be directly applied; and the mathematical expressions from one scenario cannot be used to simulate another situation. The effects of void ratio, initial water content, stress state and high suction were studied in this work revealing that water content and stress state are more important than the other effects; but that the influences tend to decrease when suction increases. The van Genuchten model was modified to simulate better the changes in the degree of saturation at low values of suction. Predictions were compared with experimental results to determine the simulation capability of the model.

Prediction of loess soil-water characteristic curve by mercury intrusion porosimetry

Mercury intrusion porosimetry(MIP)is a simple and fast way to obtain the pore distribution of soil and can be used to estimate the soil-water characteristic curve(SWCC).In previous studies,soil was assumed to be a perfect wettability material,and the contact angle(CA)of the soil-water interface was taken as zero in the SWCC prediction method.However,the CA has proved to be much greater than zero even for hydrophilic soils according to some soil wettability experiments,and it has a significant effect on predicting the SWCC.In this research,a method for predicting the SWCC by MIP,which takes the CA as a fitting coefficient,is proposed.The pore size distribution curves are measured by MIP,and the SWCCs of two loess soils are measured by pressure plate and filter paper tests.When the CA is taken as70°and 50°for the wetting and drying process,respectively,the SWCCs predicted by the pore size distribution curves agree well with the measured SWCCs.The predicted suction range of the proposed method is 0-105 k Pa.The consistency of the results suggests that utilizing the MIP test to predict the SWCC with a proper CA is effective for loess.

Effects of sample dimensions and shapes on measuring soil-water characteristic curves using pressure plate

It is well known that soilewater characteristic curve （SWCC） plays an important role in unsaturated soil mechanics, but the measurement of SWCC is inconvenient. In laboratory it requires days of testing time. For fine-grained clays, it may last for a couple of months using pressure plate tests. In this study, the effects of sample dimensions and shapes on the balance time of measuring SWCCs using pressure plate tests and the shape of SWCCs are investigated. It can be found that the sample dimensions and shapes have apparent influence on the balance time. The testing durations for circular samples with smaller diameters and annular samples with larger contact area are significantly shortened. However, there is little effect of sample dimensions and shapes on the shape of SWCCs. Its mechanism is explored and discussed in details through analysing the principle of pressure plate tests and microstructure of the sample. Based on the above findings, it is found that the circular samples with smaller dimensions can accelerate the testing duration of SWCC using the pressure plate.

Predicting the entire soil-water characteristic curve using measurements within low suction range

The soil-water characteristic curve(SWCC) is widely used in the design and evaluation in the practice of geotechnical and geoenvironmental engineering such as the slope stability under the influence of environmental factors. The SWCC has distinct features in the capillary and adsorption zones due to different physical mechanisms. Measurements of the SWCC are typically limited within the capillary zone(i.e., low suction range). It is cumbersome and time-consuming to measure the SWCC in the adsorption zone(i.e., high suction range). This study presents a simple method to predict the entire SWCC within both the capillary and adsorption zones, using measured data only from low suction range(e.g., from 0 to 500 kPa). Experimental studies were performed on a completely weathered granite residual soil to determine its entire SWCC from saturated to dry conditions. The resultant SWCC, along with the SWCC measurements of 14 soils reported in the literature, were used to validate the proposed method. The results indicate that the proposed method has good consistency with a wide array of measured data used in this study. The proposed method is easy to use as it only requires a simple parameter calibration for a commonly used SWCC model. It can be used to improve the reliability in the prediction of the SWCC over the entire suction range when measurements are limited within the low suction range.

Determination of site-specific soil-water characteristic curve from a limited number of test data-A Bayesian perspective

Determining soilewater characteristic curve(SWCC) at a site is an essential step for implementing unsaturated soil mechanics in geotechnical engineering practice, which can be measured directly through various in-situ and/or laboratory tests. Such direct measurements are, however, costly and timeconsuming due to high standards for equipment and procedural control and limits in testing apparatus. As a result, only a limited number of data points(e.g., volumetric water content vs. matric suction)on SWCC at some values of matric suction are obtained in practice. How to use a limited number of data points to estimate the site-specific SWCC and to quantify the uncertainty(or degrees-of-belief) in the estimated SWCC remains a challenging task. This paper proposes a Bayesian approach to determine a site-specific SWCC based on a limited number of test data and prior knowledge(e.g., engineering experience and judgment). The proposed Bayesian approach quantifies the degrees-of-belief on the estimated SWCC according to site-specific test data and prior knowledge, and simultaneously selects a suitable SWCC model from a number of candidates based on the probability logic. To address computational issues involved in Bayesian analyses, Markov Chain Monte Carlo Simulation(MCMCS), specifically Metropolis-Hastings(M-H) algorithm, is used to solve the posterior distribution of SWCC model parameters, and Gaussian copula is applied to evaluating model evidence based on MCMCS samples for selecting the most probable SWCC model from a pool of candidates. This removes one key limitation of the M-H algorithm, making it feasible in Bayesian model selection problems. The proposed approach is illustrated using real data in Unsaturated Soil Database(UNSODA) developed by U.S. Department of Agriculture. It is shown that the proposed approach properly estimates the SWCC based on a limited number of site-specific test data and prior knowledge, and reflects the degrees-of-belief on the estimated SWCC in a rational and quantitative manner.

A dynamic soil freezing characteristic curve model for frozen soil

The soil freezing characteristic curve(SFCC)plays a fundamental role in comprehending thermohydraulic behavior and numerical simulation of frozen soil.This study proposes a dynamic model to uniformly express SFCCs amidst varying total water contents throughout the freezing-thawing process.Firstly,a general model is proposed,wherein the unfrozen water content at arbitrary temperature is determined as the lesser of the current total water content and the reference value derived from saturated SFCC.The dynamic performance of this model is verified through test data.Subsequently,in accordance with electric double layer(EDL)theory,the theoretical residual and minimum temperatures in SFCC are calculated to be-14.5℃to-20℃for clay particles and-260℃,respectively.To ensure that the SFCC curve ends at minimum temperature,a correction function is introduced into the general model.Furthermore,a simplified dynamic model is proposed and investigated,necessitating only three parameters inherited from the general model.Additionally,both general and simplified models are evaluated based on a test database and proven to fit the test data exactly across the entire temperature range.Typical recommended parameter values for various types of soils are summarized.Overall,this study provides not only a theoretical basis for most empirical equations but also proposes a new and more general equation to describe the SFCC.

Effect of the uncertainty in soil-water characteristic curve on the estimated shear strength of unsaturated soil

Most failures or instabilities of geotechnical structures commonly result from shear failure in soil. In addition, many infrastructures are constructed within the unsaturated zone. Therefore, the determination of shear strength of unsaturated soil is crucial in geotechnical design. The soil-water characteristic curve(SWCC) is commonly used to estimate the shear strength of unsaturated soil because the direct measurement is time-consuming and costly. However, the uncertainty associated with the determined SWCC is rarely considered in the estimation of the shear strength. In this paper, the uncertainties of SWCC resulted from different factors are reviewed and discussed. The variability of the estimated shear strength for the unsaturated soil due to the uncertainty of SWCC associated with the best fit process is quantified by using the upper and lower bounds of the determined SWCC. On the other hand, the uncertainties of the estimated shear strength due to different initial void ratios or different confining pressures are quantified by adopting different SWCCs. As a result, it is recommended that the measured SWCC from the conventional Tempe cell or pressure plate needs to be corrected by considering different stress levels in the estimation of the shear strength of unsaturated soil.

Effect of initial gravimetric water content and cyclic wetting-drying on soil-water characteristic curves of disintegrated carbonaceous mudstone

The soil-water characteristic curve(SWCC)is often used to estimate unsaturated soil properties(e.g.strength,permeability,volume change,solute and thermal diffusivity).The SWCC of soil samples is significantly affected by cyclic wetting-drying.To examine how water content and cyclic wetting-drying affect the SWCC of disintegrated carbonaceous mudstone(DCM),SWCC tests were implemented using a pressure-plate apparatus.In addition,SWCC models for DCM considering the initial gravimetric water content and cyclic wetting-drying were developed.The test results showed that the volumetric water content(θ)of the DCM first decreased rapidly and then became stable as matric suction(s)increased.The initial water content affected the SWCC by altering the pore structure of the DCM.For a given number of wetting-drying cycles,the higher the initial water content,the higher the stabilizedθ.At a given s value,θdecreased as the number of wetting-drying cycles increased,which suggests that cyclic wetting-drying reduces the water-holding capacity of DCM.The Gardner model for DCM was constructed considering initial water content and cyclic wetting-drying,and was effective at describing and predicting the SWCC model for DCM.

Water infiltration and soil-water characteristics of compacted loess under applied vertical stress

Additional stress formed by postconstruction buildings in loess-filling areas affects water infiltration in soil and causes soil deformation.To investigate this effect,under constant water head,vertical infiltration tests on compacted loess with two initial dry densities for different applied vertical stresses were developed using vertical stresscontrollable one-dimensional soil columns.The timehistory curves of vertical deformation,wetting front depth,cumulative infiltration depth,volumetric water content(VWC)and suction were measured,and the soil-water characteristic curves(SWCCs)were determined.The results showed that:(1)the infiltration ability of the soil column weakens with increasing applied vertical stress and initial dry density;(2)vertical deformation increases rapidly at first and then tends to be stable slowly at the consolidation and wetting-induced deformation stage,and is positively correlated with applied vertical stress and is negatively correlated with initial dry density.The stability time of wetting-induced deformation and the corresponding wetting front depth increase with the increase of applied vertical stress,while they decrease obviously when initial dry density increases;(3)the influence of applied vertical stress on soilwater characteristics in soil columns with various initial dry densities is related to the deformation depth of soil column.The VG(Van Genuchten)model is suitable for fitting the SWCCs at different monitoring positions.A normalized SWCC model introducing the applied vertical stress was proposed for each initial dry density using the mathematical relationship between the fitting parameters and the applied vertical stress.

Rapid testing and prediction of soil–water characteristic curve of subgrade soils considering stress state and degree of compaction

The subgrade soil is generally in saturated or unsaturated condition. To analyze complex thermo-hydro-mechanical-chemical (THMC) behaviors of subgrade, it is essential to determine the soil–water characteristic curve (SWCC) that represents the relationship between matric suction and moisture content. In this study, a full-automatic rapid stress-dependent SWCC pressure-plate extractor was developed. Then, the influences of overburden stress and degree of compaction on the SWCC of subgrade soil such as high liquid limit silt (MH) and low liquid limit clay (CL) were analyzed. Accordingly, a new model taking into account the influences of overburden stress and degree of compaction based on the well-known Van Genuchten (VG) SWCC fitting model was presented and validated. The results show that with the increase of the degree of compaction and overburden stress, the saturated moisture content of subgrade soil decreases, while the air-entry value increases and the transition section curve becomes flat. The influences of the degree of compaction and overburden stress on the SWCC of MH is greater than that of CL. Meanwhile, there was a satisfactory agreement between the prediction and measurement, indicating a good performance of the new model for predicting the SWCC.

Soil-water characteristic surface model of soil-rock mixture

The relationship between the water content or saturation of unsaturated soils and its matrix suction is commonly described by the soilwater characteristic curve(SWCC).Currently,study on the SWCC model is focused on fine-grained soils like clay and silty soils,but the SWCC model for grinding soil-rock mixture(SRM)is less studied.Considering that the SRM is in a certain compaction state in the actual project,this study established a surface model with three variables of coupling compaction degree-substrate suction-moisture content based on the Cavalcante-Zornberg soil-water characteristic curve model.Then,the influence of each fitting parameter on the curve was analyzed.For the common SRM,the soil-water characteristic test was conducted.Moreover,the experimental measurements exhibit remarkable consistency with the mode surface.The analysis shows that the surface model intuitively describes the soil-water characteristics of grinding SRM,which can provide the SWCC of soils with bimodal pore characteristics under specific compaction degrees.Furthermore,it can reflect the influence of compaction degrees on the SWCC of rock-soil mass and has a certain prediction effect.The SWCC of SRM with various soil-rock ratios have a double-step shape.With the increase in compaction degree,the curves as a whole tend toward decreasing mass moisture content.The curve changes are mainly concentrated in the large pore section.

Soil-water characteristics and shear strength in constant water content triaxial tests on Yunnan red clay

The shear strength parameters for geotechnical designs are obtained mainly from consolidated drained （CD） or consolidated undrained （CU） triaxial tests. However, during construction, the excess pore-air pressure generally dissipates instantaneously while the excess pore-water pressure dissipates with time. This condition needs to be simulated in a constant water content （CW） triaxial test. The study on Yunnan red clay is carried out to investigate the soil-water characteristics and the shear strength characteristics under the constant water content condition. Osmotic technique is used to obtain the soil-water characteristic curve. A series of CW triaxial tests are conducted on statically compacted specimens. The experimental results show that the soil-water characteristic curve has a low air entry value of 7 kPa due to large pores in non-uniform pore size distribution, and a high residual value exceeding 10 MPa. In addition, the initial degree of saturation and net confining stress play an important role in affecting the shear characteristics under the constant water content condition. Finally, a new semi-empirical shear strength model in terms of degree of saturation is proposed and then applied to Yuunan red clay. Simulation result shows that the model is capable of capturing some key features of soils. The model can be used in whole engineering practice range, covering both unsaturmed and saturated soils.

The Convergence Characteristic of the Forward I-V Characteristic Curves of a Semiconductor Silicon Barrier at Different Temperatures

The /-V-（T） characteristic curves of p-n junctions with the forward voltage as the independent variable, the logarithm of forward current as the dependent variable, and the junction temperature as the parameter, almost converge at one point in the first quadrant. The voltage corresponding with the convergence point nearly equals the bandgap of the semiconductor material. This convergence point can be used to obtain the I-V characteristic curve at any temperature.

Design and Application of Automatic Test System of Soil Water Characteristic Curve

[Objective] In order to better meet the requirement of crops on a more and more accurate water content under various planting environment of modern agri-culture, an automatic test system of soil water characteristic curve was designed by combining the conceptions of soil moisture content and soil water potential. [Method] Electronic soil moisture tension meter was used to determine the real-time tension value of soil moisture in the tested container, and the electronic Weigh sensor was used to determine soil Weigh. Minusing method was used to calculate soil moisture content, based on which the soil water characteristic curve was plotted. [Result] Through the filed survey of 2 different kinds of soil in Jiangsu Province, the results were as fol ows： soil of different composition showed different trend in soil water characteristic curve that the soil water characteristic relation of the sandy soil in the old course of the Yel ow River in Xuzhou was Y=-0.000 2X3＋0.027 7X2-1.644 5X＋38.161, R2=0.991 9; while the soil water characteristic relation of the saline-alkali soil in Jinhai Farm of Dafeng was Y=-0.00 2X2-0.426X＋39.905, R2=0.991 3. [Con-clusion] The automatic test system of soil water characteristic curve soil water char-acteristics curve could reflect soil moisture content and soil water potential, as wel as reflect the effectiveness of soil water to plant growth, providing basis for the sci-entific irrigation.

Characteristics of In-Situ Soil Water Hysteresis Observed through Multiple-Years Monitoring

A soil water retention curve (SWRC) is an essential soil physical property for analyzing transport and retention of water in a soil layer. A SWRC is often described as a single-valued function that relates the soil water potential ψ to volumetric water content θ of the soil. However, an in-situ ψ − θ relation should show soil water hysteresis, though this fact is often neglected in analyses of field soil water regimes while long-term in-situ soil water hysteresis is not well characterized. This study aimed at probing and characterizing in-situ ψ − θ relations. The developments of large hysteresis in the in-situ ψ − θ relations were observed only a few times during the study period of 82 months. Any of the large hysteretic behaviors in the ψ − θ relations began with an unusually strong continual reduction in ψ. The completion of a hysteresis loop required a recorded maximum rainfall. Because the study field had very small chances to meet such strong rainfall events, it took multiple years to restore the fraction of soil water depleted by the unusually strong continual reduction in ψ. While wetting-drying cycles had occurred within a certain domain of ψ, hysteretic behaviors tended to be so small that the in-situ ψ − θ relation can be approximated as a single-valued function of θ(ψ). These observed patterns of the in-situ ψ − θ relations were characterized by kinds of difference in dθ/dψ between a drying process and a wetting process at a given ψ. Thus, more amounts of experimental facts about wetting SWRCs in parallel with drying SWRCs should be needed for correct modelling, analyzing, and predicting soil water regimes in fields. It is also necessary to increase our understandings about the long-term trends of occurrences of extreme weather conditions associated with possible change in climate.

Soil freezing process and different expressions for the soil-freezing characteristic curve

The soil-freezing characteristic curve(SFCC),which represents the relationship between unfrozen water content and subfreezing temperature(or suction at ice-water interface)in a freezing soil,can be used for understanding the transportation of heat,water,and solute in frozen soils.In this paper,the soil freezing process and the similarity between the SFCC of saturated frozen soil and soil-water characteristic curve(SWCC)of unfrozen unsaturated soil are reviewed.Based on similar characteristics between SWCC and SFCC,a conceptual SFCC is drawn for illustrating the main features of soil freezing and thawing processes.Various SFCC expressions from the literature are summarized.Four widely used expressions(i.e.,power relationship,exponential relationship,van Genuchten 1980 equation and Fredlund and Xing 1994 equation)are evaluated using published experimental data on four different soils(i.e.,sandy loam,silt,clay,and saline silt).Results show that the exponential relationship and van Genuchten(1980)equation are more suitable for sandy soils.The simple power relationship can be used to reasonably best-fit the SFCC for soils with different particle sizes;however,it exhibits limitations when fitting the saline silt data.The Fredlund and Xing(1994)equation is suitable for fitting the SFCCs for all soils studied in this paper.

Prediction of Abdominal Visceral Obesity From Body Mass Index,Waist Circumference and Waist-hip Ratio in Chinese Adults:Receiver Operating Characteristic Curves Analysis

Objective To evaluate the sensitivity and specificity of body mass index (BMI), waist circumference (WC) and waist-to-hip ratio (WHR) measurements in diagnosing abdominal visceral obesity. Methods BMI, WC, and WHR were assessed in 690 Chinese adults (305 men and 385 women) and compared with magnetic resonance imaging (MRI) measurements of abdominal visceral adipose tissue (VA). Receiver operating characteristic (ROC) curves were generated and used to determine the threshold point for each anthropometric parameter. Results 1) MRI showed that 61.7% of overweight/obese individuals (BMI≥25 kg/m2) and 14.2% of normal weight (BMI<25 kg/m2) individuals had abdominal visceral obesity (VA≥100 cm2). 2) VA was positively correlated with each anthropometric variable, of which WC showed the highest correlation (r=0.73-0.77, P<0.001). 3) The best cut-off points for assessing abdominal visceral obesity were as followed: BMI of 26 kg/m2, WC of 90 cm, and WHR of 0.93, with WC being the most sensitive and specific factor. 4) Among subjects with BMI≥28 kg/m2 or WC≥95 cm, 95% of men and 90% of women appeared to have abdominal visceral obesity. Conclusion Measurements of BMI, WC, and WHR can be used in the prediction of abdominal visceral obesity, of which WC was the one with better accuracy.

Distribution characteristics of dissolved organic carbon in annular wetland soil-water solutions through soil profiles in the Sanjiang Plain,Northeast China

Overwhelming evidence reveals that concentrations of dissolved organic carbon （DOC） have increased in streams which brings negative environmental impacts. DOC in stream flow is mainly originated from soil-water solutions of watershed. Wetlands prove to be the most sensitive areas as an important DOC reserve between terrestrial and fluvial biogeosystems. This reported study was focused on the distribution characteristics and the controlling factors of DOC in soil-water solutions of annular wetland, i.e., a dishing wetland and a forest wetland together, in the Sanjiang Plain, Northeast China. The results indicate that DOC concentrations in soilwater solutions decreased and then increased with increasing soil depth in the annular wetland. In the upper soil layers of 0-10 cm and 10-20 cm, DOC concentrations in soil-water solutions linearly increased from edge to center of the annular wetland （R^2 = 0.3122 and R^2 = 0.443）. The distribution variations were intimately linked to DOC production and utilization and DOC transport processes in annular wetland soil-water solutions. The concentrations of total organic carbon （TOC）, total carbon （TC） and Fe（II）, DOC mobility and continuous vertical and lateral flow affectext the distribution variations of DOC in soil-water solutions. The correlation coefficients between DOC concentrations and TOC, TC and Fe（II） were 0.974, 0.813 and 0.753 respectively. These distribution characteristics suggested a systematic response of the distribution variations of DOC in annular wetland soil-water solutions to the geometry of closed depressions on a scale of small catchments. However, the DOC in soil pore water of the annular wetland may be the potential source of DOC to stream flow on watershed scale. These observations also implied the fragmentation of wetland landscape could bring the spatial-temporal variations of DOC distribution and exports, which would bring negative environmental impacts in watersheds of the Sanjiang Plain.

Effect of temperature on soil-water characteristics and hysteresis of compacted Gaomiaozi bentonite

Laboratory tests under different constraint conditions were carried out to obtain the soil-water retention curves(SWRCs) of highly-compacted confined/unconfined Gaomiaozi(GMZ) bentonite at 20,40 and 80 ℃,respectively. The effect of temperature on the soil-water characteristics of the highly-compacted GMZ bentonite was analyzed. The results show that the water retention capacity of the highly-compacted GMZ bentonite decreases as the temperature increases under unconfined and confined conditions. At a certain temperature,the constraint conditions have little influence on the water retention capacity of the compacted bentonite at high suction,but the water retention capacity of the confined specimen is lower than that of the unconfined specimen at low suction. Under unconfined conditions,the hysteretic behaviour of the compacted bentonite decreases with increasing temperature. At high suction(>4 MPa) ,the hysteretic behaviour of the unconfined bentonite tends to increase with the decrease of the suction. In summary,the hysteretic behaviour of the compacted bentonite is not significant.

Prediction of soil–water characteristic curve for Malan loess in Loess Plateau of China

To predict the soil-water characteristic curve(i.e.SWCC)of natural and remoulded Malan loess from soil physical properties,one-point methods for determining the SWCC that are much simpler than experimental methods are proposed.The predicted SWCC is presented in the form of the BRUTSAERT equation,in which the four model parameters can be estimated from soil physical properties using the best correlations obtained in the present study along with one measured data point.The proposed one-point methods are validated using the measured SWCC data reported in the literature.The results of validation studies suggest that the proposed one-point methods can provide reasonable prediction of the SWCC for natural and remoulded Malan loess.The measured data point should be within the transition zone;the measured suction is suggested between25to100kPa for natural loess,while between100to500kPa for remoulded loess.