CdS microcrystallite doped SiO 2 glass films on titanium metal substrates were prepared by sol gel process. The effects of solution composition and viscosity, heat treatment parameters and substrate pretreatment m...CdS microcrystallite doped SiO 2 glass films on titanium metal substrates were prepared by sol gel process. The effects of solution composition and viscosity, heat treatment parameters and substrate pretreatment method on the film qualities were studied. The transformation process of gel to CdS doped SiO 2 glass film, the structure of these films, the substrate/film interface bonding state and crystalline phase were analyzed by DTA, IRRS, SEM, EDS and XRD. The IRRS results show that Si O Ti linkages are formed between titanium substrate and thin film during heat treatment process. The preferential heat treatment of titanium surface in oxidizing atmosphere will be beneficial to increase the interface bonding strength. The thin films bonded with the substrates chemically and contained very fine CdS crystals with 20~40 nm in size.展开更多
The supported membranes of Al 2O 3 and its modification membranes were prepared.Al 2O 3,Al 2O 3 SiO 2 TiO 2 and Al 2O 3 SiO 2 TiO 2 ZrO 2 membranes were mamufatured by the slip casting process using...The supported membranes of Al 2O 3 and its modification membranes were prepared.Al 2O 3,Al 2O 3 SiO 2 TiO 2 and Al 2O 3 SiO 2 TiO 2 ZrO 2 membranes were mamufatured by the slip casting process using mixing boehmite,silicate,titania and zirconia sols under proper conditions,then the composite membrane was prepared.The structure and characteristics of the membrane were determined by XRD,SEM and AFM measurement.The conditions of preparation of the membrane are discussed.The thickness of the layer is about 1-2μm,the diameter of an average pore is 200-300nm and has a narrow pore distribution without crack forming.By changing the ratios of Al∶Si∶Ti∶Zr(mol),variations of surface pore size of Al 2O 3 SiO 2 TiO 2 ZrO 2 membrane can be gained.展开更多
Mesoporous poly(styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis was achieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydrid...Mesoporous poly(styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis was achieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydride copolymer in the presence of 3-aminopropyl triethoxysilane (APTES) as a coupling agent and citric acid as a nonsurfactant template or pore-forming agent, followed by ethanol extraction. Characterization results from nitrogen sorption isotherms and powder X-ray diffraction indicate that polymer-modified mesoporous materials with large specific surface areas (e.g. 900 m(2)/g) and pore volumes (e.g. 0.6 cm(3)/g) could be prepared. As the citric acid concentration is increased, the specific surface areas, pore volumes and pore diameters of the hybrid materials increase.展开更多
Nanosized cerium-doped lutetium aluminum garnet (LuAG:Ce) phosphors were prepared by nitrate-citrate solgel combustion process using 1:1 ratio of the citrate:nitrate. The prepared LuAG:Ce phosphors were characte...Nanosized cerium-doped lutetium aluminum garnet (LuAG:Ce) phosphors were prepared by nitrate-citrate solgel combustion process using 1:1 ratio of the citrate:nitrate. The prepared LuAG:Ce phosphors were characterized by XRD, TEM, photoluminescence and radioluminescence spectra excited by UV and X-ray, respectively. The purified crystalline phase of LuAG:Ce was obtained at 900 ℃ by directly crystallizing from amorphous materials. The resultant Lu- AG:Ce phosphors were uniform and had good dispersivity with an average particle size of about 30 urn. Both photoluminescence and radioluminescence were well-known Ce^3+ emissions located in the range of 470 -600 nm consisting of two emission bands because of the transition from the lowest 5d excited state (2D) to the 4f ground state of Ce^3+, which matched well with the sensitivity curve of the Si-photodiode. There was a little red shift for the emission components from the UV-excited emission spectrum to the X-ray-excited emission spectrum. The fast scintillation decay component of 26 ns satisfies the requirements of fast scintillators.展开更多
CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared s...CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.展开更多
The phase-transformation in sol-gel preparation of barium hexaferrite and the formation of barium hexaferrite doped with La 3+ were studied by chemical p hase analysis, X-ray diffraction and infrared spectrometry an...The phase-transformation in sol-gel preparation of barium hexaferrite and the formation of barium hexaferrite doped with La 3+ were studied by chemical p hase analysis, X-ray diffraction and infrared spectrometry analysis. The expe rimental results show that phase transformation reactions of FeCO 3, Fe 2O 3 and BaFe 2O 4, barium hexaferrite and γ-Fe 2O 3 take place in the heat tr eatment of gel. While the doping lanthanide ion replace barium ion, an equivalen t quantity of Fe 3+ are reduced to Fe 2+ to maintain the charge equili brium.展开更多
In order to prevent BaMgAl10O17∶Eu (BAM) phosphor from thermal degradation, MgF2-coatings on the surface of BAM were prepared by a sol-gel process. The coatings were characterized by X-ray photoelectron spectroscop...In order to prevent BaMgAl10O17∶Eu (BAM) phosphor from thermal degradation, MgF2-coatings on the surface of BAM were prepared by a sol-gel process. The coatings were characterized by X-ray photoelectron spectroscopy and scanning electron microscopy. The results indicate that BAM is successfully coated with homogenous, close MgF2 coatings. The photoluminescence and anti-thermal degradation properties of coated BAM were investigated under 254 and 147 nm excitations. The optimum anti-thermal degradation properties are obtained at the mass ratio of MgF2 to BAM 0.2% under 254 nm excitation and 0.5% under 147 nm excitation, respectively. It is considered that trace MgO formed after baked would cause different optimum coating thicknesses under 254 and 147 nm excitations.展开更多
Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals ...Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals of ZnO grow well.Scanning electron microscopy and atomic force microscopy results indicate that the samples have a good structure and lower surface roughness.The nonlinear V–I characteristics of the films show that La2 O3 develops the electrical properties largely and the best doped content is 0.3% lanthanum ion,with the leakage current of 0.25 mA,the threshold field of 150 V/mm and the nonlinear coefficient of 4.0 in detail.展开更多
Hafnium oxide thin films (HOTFs) were successfully deposited onto amorphous glasses using chemical bath deposition, successive ionic layer absorption and reaction (SILAR), and sol-gel methods. The same reactive pr...Hafnium oxide thin films (HOTFs) were successfully deposited onto amorphous glasses using chemical bath deposition, successive ionic layer absorption and reaction (SILAR), and sol-gel methods. The same reactive precursors were used for all of the methods, and all of the films were annealed at 300℃ in an oven (ambient conditions). After this step, the optical and structural properties of the films produced by using the three different methods were compared. The structures of the films were analyzed by X-ray diffTaction (XRD). The optical properties are investigated using the ultraviolet-visible (UV-VIS) spectroscopic technique. The film thickness was measured via atomic force microscopy (AFM) in the tapping mode. The surface properties and elemental ratios of the films were investigated and measured by scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDX). The lowest transmittance and the highest reflectance values were observed for the films produced using the SILAR method. In addition, the most intense characteristic XRD peak was observed in the diffraction pattern of the film produced using the SILAR method, and the greatest thickness and average grain size were calculated for the film produced using the SILAR method. The films produced using SILAR method contained fewer cracks than those produced using the other methods. In conclusion, the SILAR method was observed to be the best method for the production of HOTFs.展开更多
A new organic/inorganic hybrid nonlinear optical (NLO) material was developed by the sol-gel process of an alkoxysilane dye with tetraethoxysilane. A NLO moiety based on 4-nitro-4 ' -hydroxy azobenzene was covalen...A new organic/inorganic hybrid nonlinear optical (NLO) material was developed by the sol-gel process of an alkoxysilane dye with tetraethoxysilane. A NLO moiety based on 4-nitro-4 ' -hydroxy azobenzene was covalently bonded to the triethoxysilane derivative, i.e, gamma -isocyanatopropyl triethoxysilane. The preparation process and properties of the sol-gel derived NLO polymer were studied and characterized by SEM, FTIR,H-1-NMR, UV-Vis, DSC and second harmonic generation (SHG) measurement. The results indicated that the chemical bonding of the chromophores to the inorganic SiO2 networks induces low dipole alignment relaxation and preferable orientational stability. The SHG measurements also showed that the bonded polymer film containing 75 wt% of the akoxysilane dye has a high electro-optic coefficient (r(33)) of 7.1 pm/V at 1.1 mum wavelength, and exhibit good SHG stability, the r(33) values can maintain about 92.7% of its initial value at room temperature for 90 days, and can maintain about 59.3% at 100 degreesC for 300 min.展开更多
Four phenoxysilicon networks for nonlinear optical (NLO) applications were designed and prepared by an extended sol-gel process without additional H2O and catalyst. All poled polymer network films possess high second-...Four phenoxysilicon networks for nonlinear optical (NLO) applications were designed and prepared by an extended sol-gel process without additional H2O and catalyst. All poled polymer network films possess high second-order nonlinear optical coefficients (d(33)) Of 10(-7)similar to 10(-8) esu. The investigation of NLO temporal stability at room temperature and elevated temperature (120 degreesC) indicated that these films exhibit high d(33) stability because the orientation of the chromophores are locked in the phenoxysilicon organic/inorganic networks.展开更多
In this work, TiO2 nanorods with uniform diameter of about 100 nm and a length of several micrometers were successfully prepared by the sol-gel template method. Also the influence of molar ratios of precursor on the m...In this work, TiO2 nanorods with uniform diameter of about 100 nm and a length of several micrometers were successfully prepared by the sol-gel template method. Also the influence of molar ratios of precursor on the morphology and structure of TiO2 nanorods has been investigated. The prepared samples were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD results indicated that the TiO2 nanorods were crystallized in the anatase and rutile phases, after annealing to 400-700℃ up to 2 h.展开更多
Hydroxyapatite/alumina nanocrystalline composite powders needed for various biomedical applications were successfully synthe- sized by sol-gel process. Structural and morphological investigations of the prepared compo...Hydroxyapatite/alumina nanocrystalline composite powders needed for various biomedical applications were successfully synthe- sized by sol-gel process. Structural and morphological investigations of the prepared composite powders were performed using X-ray dif- fractometer (XRD), scanning electron microscopy (SEM), X'Pert HighScore software, and Clemex Vision image analysis software. The re- suits show that the crystallite size of the obtained composite powders is in the range of 25 to 90 nm. SEM evaluation shows that the obtained composite powders have a porous structure, which is very useful for biomedical applications. The spherical nanoparticles in the range of 60 to 800 nm are embedded in the agglomerated clusters of the prepared composite powders.展开更多
Nanometer ZrO2 - 8% Y2O3 (mole fraction, % ) powders were prepared by the EDTA (ethylenediaminetetraacetic acid) sol-gel process. Effects of the addition of ethylene glycol on agglomerate control was investigated. The...Nanometer ZrO2 - 8% Y2O3 (mole fraction, % ) powders were prepared by the EDTA (ethylenediaminetetraacetic acid) sol-gel process. Effects of the addition of ethylene glycol on agglomerate control was investigated. The results showed that because of the replacement of hydrogen bonds with ethylene glycol in the polymerized gel, gel stabilization and homogeneity were improved and close approach of gel particles was prevented, which led to reduction of hard agglomerates to some extent. Calcined at 4OO t for 2 h and 700 C for 2 h, the powders had a specific surface area of 35 m2/g, average particle size of 28 nm, and median particle size (d50) of 0. 44um with very sharp distribution, mostly being soft agglomerates.展开更多
Nano silica-modified epoxy resins were synthesized by the sol-gel process, The materials have the morphological structure of nano particales dispersed in the epoxy matrix. The dispersed phase formed a physical network...Nano silica-modified epoxy resins were synthesized by the sol-gel process, The materials have the morphological structure of nano particales dispersed in the epoxy matrix. The dispersed phase formed a physical network in the resin and thus influenced the rheological behavior greatly. However, the nano silica did not show a significant influence on the mechanical properties of the cured resins.展开更多
An effective and reproducible preparation of silica sol nanospheres via a modified sol-gel process has been described. Monodisperse and stable silica sol nanospheres with uniformsize were successfully obtained through...An effective and reproducible preparation of silica sol nanospheres via a modified sol-gel process has been described. Monodisperse and stable silica sol nanospheres with uniformsize were successfully obtained through the optimized synthesis in which the mixture of tetraethyl orthosilicate (TEOS) and ethanol was followed by the addition of water and ammonium hydroxide (NH3) separately, and the size of silica sol spheres was strictly controlled in the range of 25-119 nm with a narrow size distribution by fine adjustment of several reaction parameters. Results showed that in the presence of low concentration of TEOS, spheres size rose first and reached maximum when H2O concentration was up to 66 g/L. However, the diameter of silica sol spheres decreased above 66 g/L of H2O concentration. Furthermore, it was also found that the size and size distribution of silica sol nanospheres were affected by NH3 concentration. As NH3 concentration increased from 15 to 35 g/L, the diameter declined from 83 to 64 nm. Nevertheless, higher NH3 concentration would result in relatively broad size distribution, and gelation occurred when NH3 concentration reached 44 g/L. In addition, the effect of the different feed rates ofNH3 on the size growth of silica sol nanospheres was also discussed.展开更多
Pr Doped BaTi4O9 gel was prepared by sol-gel method using Ti(OC4H9)4, Ba(CH3COO)2, CH3COOH and CH3OCH2CH2OH as raw materials. Through analyzing dry gel thermal treated at different temperatures, the possible synthesis...Pr Doped BaTi4O9 gel was prepared by sol-gel method using Ti(OC4H9)4, Ba(CH3COO)2, CH3COOH and CH3OCH2CH2OH as raw materials. Through analyzing dry gel thermal treated at different temperatures, the possible synthesis mechanism of Pr doped BaTi4O9 powder was discussed. At first, Ti(OC4H9)4 hydrolyzes and three dimensional networks form, in which Ba2+ and CH3COO- are mostly in the form of ions; organic solvent is gradually volatilized through calefaction at 700 ℃, then the offspring is turned into BaTi5O11. With the temperature increasing to 850 ℃, BaTi5O11 begins resolving partly and forming BaTi4O9, and at 1000℃ Ba4Ti13O22 forms partly, but BaTi4O9 is the main crystal phase. BaTi5O11 and Ba4Ti13O30 decomposes completely at 1200℃ and forms single-phase BaTi4O9. The infrared (IR) analysis also shows that the absorbing peak of Ti-O bond is not in the characteristic absorption range of Ti-O-Ti (700-900 cm-1), but slightly shifted to the higher end (908 cm-1). It is probably because that doping Pr enters into the crystal lattice and causes the abnormal absorption of Ti-O bond.展开更多
文摘CdS microcrystallite doped SiO 2 glass films on titanium metal substrates were prepared by sol gel process. The effects of solution composition and viscosity, heat treatment parameters and substrate pretreatment method on the film qualities were studied. The transformation process of gel to CdS doped SiO 2 glass film, the structure of these films, the substrate/film interface bonding state and crystalline phase were analyzed by DTA, IRRS, SEM, EDS and XRD. The IRRS results show that Si O Ti linkages are formed between titanium substrate and thin film during heat treatment process. The preferential heat treatment of titanium surface in oxidizing atmosphere will be beneficial to increase the interface bonding strength. The thin films bonded with the substrates chemically and contained very fine CdS crystals with 20~40 nm in size.
基金Project cooperated with College of Environment Engineering,Huazhong University of Technology
文摘The supported membranes of Al 2O 3 and its modification membranes were prepared.Al 2O 3,Al 2O 3 SiO 2 TiO 2 and Al 2O 3 SiO 2 TiO 2 ZrO 2 membranes were mamufatured by the slip casting process using mixing boehmite,silicate,titania and zirconia sols under proper conditions,then the composite membrane was prepared.The structure and characteristics of the membrane were determined by XRD,SEM and AFM measurement.The conditions of preparation of the membrane are discussed.The thickness of the layer is about 1-2μm,the diameter of an average pore is 200-300nm and has a narrow pore distribution without crack forming.By changing the ratios of Al∶Si∶Ti∶Zr(mol),variations of surface pore size of Al 2O 3 SiO 2 TiO 2 ZrO 2 membrane can be gained.
基金Project supported by the National Natural Science Foundation of China (No. 29874002) and the Outstanding Young Scientist Award from National Natural Science Foundation of China (No. 29825504)
文摘Mesoporous poly(styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis was achieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydride copolymer in the presence of 3-aminopropyl triethoxysilane (APTES) as a coupling agent and citric acid as a nonsurfactant template or pore-forming agent, followed by ethanol extraction. Characterization results from nitrogen sorption isotherms and powder X-ray diffraction indicate that polymer-modified mesoporous materials with large specific surface areas (e.g. 900 m(2)/g) and pore volumes (e.g. 0.6 cm(3)/g) could be prepared. As the citric acid concentration is increased, the specific surface areas, pore volumes and pore diameters of the hybrid materials increase.
基金we are very grateful to the National Natural Scieneo Founda-tion of China(No.69978017,59802007)Shanghai Edu-cation Comrnittee(No.JW99 TJ-03)for their help and 6nancialsupports.
基金The authors would like to thank the financial support of the Major State Basic Research Development Program of China (No.2002CB613303)the National Natural Science Foundation of China (No.20371038)the Foundation for Innovative Research Team of Hubei Province of China(No.2005ABC004).
基金Project supported by the National Defence Fundamental Research Project of China
文摘Nanosized cerium-doped lutetium aluminum garnet (LuAG:Ce) phosphors were prepared by nitrate-citrate solgel combustion process using 1:1 ratio of the citrate:nitrate. The prepared LuAG:Ce phosphors were characterized by XRD, TEM, photoluminescence and radioluminescence spectra excited by UV and X-ray, respectively. The purified crystalline phase of LuAG:Ce was obtained at 900 ℃ by directly crystallizing from amorphous materials. The resultant Lu- AG:Ce phosphors were uniform and had good dispersivity with an average particle size of about 30 urn. Both photoluminescence and radioluminescence were well-known Ce^3+ emissions located in the range of 470 -600 nm consisting of two emission bands because of the transition from the lowest 5d excited state (2D) to the 4f ground state of Ce^3+, which matched well with the sensitivity curve of the Si-photodiode. There was a little red shift for the emission components from the UV-excited emission spectrum to the X-ray-excited emission spectrum. The fast scintillation decay component of 26 ns satisfies the requirements of fast scintillators.
基金supported by the National Natural Science Foundation of China (NO. 20976013, 21006057)
文摘CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.
文摘The phase-transformation in sol-gel preparation of barium hexaferrite and the formation of barium hexaferrite doped with La 3+ were studied by chemical p hase analysis, X-ray diffraction and infrared spectrometry analysis. The expe rimental results show that phase transformation reactions of FeCO 3, Fe 2O 3 and BaFe 2O 4, barium hexaferrite and γ-Fe 2O 3 take place in the heat tr eatment of gel. While the doping lanthanide ion replace barium ion, an equivalen t quantity of Fe 3+ are reduced to Fe 2+ to maintain the charge equili brium.
基金Project(50272026) supported by the NSFC Project(2003AA324020) supported by the Hi tech Research and Develop ment Program of China
文摘In order to prevent BaMgAl10O17∶Eu (BAM) phosphor from thermal degradation, MgF2-coatings on the surface of BAM were prepared by a sol-gel process. The coatings were characterized by X-ray photoelectron spectroscopy and scanning electron microscopy. The results indicate that BAM is successfully coated with homogenous, close MgF2 coatings. The photoluminescence and anti-thermal degradation properties of coated BAM were investigated under 254 and 147 nm excitations. The optimum anti-thermal degradation properties are obtained at the mass ratio of MgF2 to BAM 0.2% under 254 nm excitation and 0.5% under 147 nm excitation, respectively. It is considered that trace MgO formed after baked would cause different optimum coating thicknesses under 254 and 147 nm excitations.
基金Project(20123227120021)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(BK2012156)supported by the Natural Science Foundation of Jiangsu Province,China+3 种基金Project(KFJJ201105)supported by the Opening Project of State Key Laboratory of Electronic Thin Films and Integrated Devices,ChinaProject(CJ20125001)supported by the Application Program for Basic Research of Changzhou,ChinaProject(13KJB430006)supported by the Universities Natural Science Research project of Jiangsu Province,ChinaProject supported by the Industrial Center of Jiangsu University Undergraduate Practice-Innovation Training Program,China
文摘Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals of ZnO grow well.Scanning electron microscopy and atomic force microscopy results indicate that the samples have a good structure and lower surface roughness.The nonlinear V–I characteristics of the films show that La2 O3 develops the electrical properties largely and the best doped content is 0.3% lanthanum ion,with the leakage current of 0.25 mA,the threshold field of 150 V/mm and the nonlinear coefficient of 4.0 in detail.
文摘Hafnium oxide thin films (HOTFs) were successfully deposited onto amorphous glasses using chemical bath deposition, successive ionic layer absorption and reaction (SILAR), and sol-gel methods. The same reactive precursors were used for all of the methods, and all of the films were annealed at 300℃ in an oven (ambient conditions). After this step, the optical and structural properties of the films produced by using the three different methods were compared. The structures of the films were analyzed by X-ray diffTaction (XRD). The optical properties are investigated using the ultraviolet-visible (UV-VIS) spectroscopic technique. The film thickness was measured via atomic force microscopy (AFM) in the tapping mode. The surface properties and elemental ratios of the films were investigated and measured by scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDX). The lowest transmittance and the highest reflectance values were observed for the films produced using the SILAR method. In addition, the most intense characteristic XRD peak was observed in the diffraction pattern of the film produced using the SILAR method, and the greatest thickness and average grain size were calculated for the film produced using the SILAR method. The films produced using SILAR method contained fewer cracks than those produced using the other methods. In conclusion, the SILAR method was observed to be the best method for the production of HOTFs.
基金This work was supported by the Postdoctoral Science Foundation of Guangdong Province (No. 9644) and the Natural Science Fund of Guangdong Province(No. 990629).
文摘A new organic/inorganic hybrid nonlinear optical (NLO) material was developed by the sol-gel process of an alkoxysilane dye with tetraethoxysilane. A NLO moiety based on 4-nitro-4 ' -hydroxy azobenzene was covalently bonded to the triethoxysilane derivative, i.e, gamma -isocyanatopropyl triethoxysilane. The preparation process and properties of the sol-gel derived NLO polymer were studied and characterized by SEM, FTIR,H-1-NMR, UV-Vis, DSC and second harmonic generation (SHG) measurement. The results indicated that the chemical bonding of the chromophores to the inorganic SiO2 networks induces low dipole alignment relaxation and preferable orientational stability. The SHG measurements also showed that the bonded polymer film containing 75 wt% of the akoxysilane dye has a high electro-optic coefficient (r(33)) of 7.1 pm/V at 1.1 mum wavelength, and exhibit good SHG stability, the r(33) values can maintain about 92.7% of its initial value at room temperature for 90 days, and can maintain about 59.3% at 100 degreesC for 300 min.
文摘Four phenoxysilicon networks for nonlinear optical (NLO) applications were designed and prepared by an extended sol-gel process without additional H2O and catalyst. All poled polymer network films possess high second-order nonlinear optical coefficients (d(33)) Of 10(-7)similar to 10(-8) esu. The investigation of NLO temporal stability at room temperature and elevated temperature (120 degreesC) indicated that these films exhibit high d(33) stability because the orientation of the chromophores are locked in the phenoxysilicon organic/inorganic networks.
文摘In this work, TiO2 nanorods with uniform diameter of about 100 nm and a length of several micrometers were successfully prepared by the sol-gel template method. Also the influence of molar ratios of precursor on the morphology and structure of TiO2 nanorods has been investigated. The prepared samples were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD results indicated that the TiO2 nanorods were crystallized in the anatase and rutile phases, after annealing to 400-700℃ up to 2 h.
文摘Hydroxyapatite/alumina nanocrystalline composite powders needed for various biomedical applications were successfully synthe- sized by sol-gel process. Structural and morphological investigations of the prepared composite powders were performed using X-ray dif- fractometer (XRD), scanning electron microscopy (SEM), X'Pert HighScore software, and Clemex Vision image analysis software. The re- suits show that the crystallite size of the obtained composite powders is in the range of 25 to 90 nm. SEM evaluation shows that the obtained composite powders have a porous structure, which is very useful for biomedical applications. The spherical nanoparticles in the range of 60 to 800 nm are embedded in the agglomerated clusters of the prepared composite powders.
文摘Nanometer ZrO2 - 8% Y2O3 (mole fraction, % ) powders were prepared by the EDTA (ethylenediaminetetraacetic acid) sol-gel process. Effects of the addition of ethylene glycol on agglomerate control was investigated. The results showed that because of the replacement of hydrogen bonds with ethylene glycol in the polymerized gel, gel stabilization and homogeneity were improved and close approach of gel particles was prevented, which led to reduction of hard agglomerates to some extent. Calcined at 4OO t for 2 h and 700 C for 2 h, the powders had a specific surface area of 35 m2/g, average particle size of 28 nm, and median particle size (d50) of 0. 44um with very sharp distribution, mostly being soft agglomerates.
基金This work was supported by the Ford-China Research and Development Fund (No.9415311).
文摘Nano silica-modified epoxy resins were synthesized by the sol-gel process, The materials have the morphological structure of nano particales dispersed in the epoxy matrix. The dispersed phase formed a physical network in the resin and thus influenced the rheological behavior greatly. However, the nano silica did not show a significant influence on the mechanical properties of the cured resins.
基金Funded by the Guangdong Well-Silicasol Company Limited,China
文摘An effective and reproducible preparation of silica sol nanospheres via a modified sol-gel process has been described. Monodisperse and stable silica sol nanospheres with uniformsize were successfully obtained through the optimized synthesis in which the mixture of tetraethyl orthosilicate (TEOS) and ethanol was followed by the addition of water and ammonium hydroxide (NH3) separately, and the size of silica sol spheres was strictly controlled in the range of 25-119 nm with a narrow size distribution by fine adjustment of several reaction parameters. Results showed that in the presence of low concentration of TEOS, spheres size rose first and reached maximum when H2O concentration was up to 66 g/L. However, the diameter of silica sol spheres decreased above 66 g/L of H2O concentration. Furthermore, it was also found that the size and size distribution of silica sol nanospheres were affected by NH3 concentration. As NH3 concentration increased from 15 to 35 g/L, the diameter declined from 83 to 64 nm. Nevertheless, higher NH3 concentration would result in relatively broad size distribution, and gelation occurred when NH3 concentration reached 44 g/L. In addition, the effect of the different feed rates ofNH3 on the size growth of silica sol nanospheres was also discussed.
基金Sponsored by the Scientific Research Foundation of Harbin Institute of Technology (Grant NoHIT200135)
文摘Pr Doped BaTi4O9 gel was prepared by sol-gel method using Ti(OC4H9)4, Ba(CH3COO)2, CH3COOH and CH3OCH2CH2OH as raw materials. Through analyzing dry gel thermal treated at different temperatures, the possible synthesis mechanism of Pr doped BaTi4O9 powder was discussed. At first, Ti(OC4H9)4 hydrolyzes and three dimensional networks form, in which Ba2+ and CH3COO- are mostly in the form of ions; organic solvent is gradually volatilized through calefaction at 700 ℃, then the offspring is turned into BaTi5O11. With the temperature increasing to 850 ℃, BaTi5O11 begins resolving partly and forming BaTi4O9, and at 1000℃ Ba4Ti13O22 forms partly, but BaTi4O9 is the main crystal phase. BaTi5O11 and Ba4Ti13O30 decomposes completely at 1200℃ and forms single-phase BaTi4O9. The infrared (IR) analysis also shows that the absorbing peak of Ti-O bond is not in the characteristic absorption range of Ti-O-Ti (700-900 cm-1), but slightly shifted to the higher end (908 cm-1). It is probably because that doping Pr enters into the crystal lattice and causes the abnormal absorption of Ti-O bond.