An adaptive finite-difference method for seismic traveltime modeling based on 3D eikonal equation

3D eikonal equation is a partial differential equation for the calculation of first-arrival traveltimes and has been widely applied in many scopes such as ray tracing,source localization,reflection migration,seismic monitoring and tomographic imaging.In recent years,many advanced methods have been developed to solve the 3D eikonal equation in heterogeneous media.However,there are still challenges for the stable and accurate calculation of first-arrival traveltimes in 3D strongly inhomogeneous media.In this paper,we propose an adaptive finite-difference(AFD)method to numerically solve the 3D eikonal equation.The novel method makes full use of the advantages of different local operators characterizing different seismic wave types to calculate factors and traveltimes,and then the most accurate factor and traveltime are adaptively selected for the convergent updating based on the Fermat principle.Combined with global fast sweeping describing seismic waves propagating along eight directions in 3D media,our novel method can achieve the robust calculation of first-arrival traveltimes with high precision at grid points either near source point or far away from source point even in a velocity model with large and sharp contrasts.Several numerical examples show the good performance of the AFD method,which will be beneficial to many scientific applications.

Comparative structural and electrochemical properties of mixed P2/O′3-layered sodium nickel manganese oxide prepared by sol-gel and electrospinning methods:Effect of Na-excess content

The effect of Na-excess content in the precursor on the structural and electrochemical performances of sodium nickel manganese oxide(NNMO)prepared by sol-gel and electrospinning methods is investigated in this paper.X-ray diffraction results of the prepared NNMO without adding Na-excess content indicate sodium loss,while the mixed phase of P2/O′3-type layered NNMO presented after adding Na-excess content.Compared with the sol-gel method,the secondary phase of NiO is more suppressed by using the electrospinning method,which is further confirmed by field emission scanning electron microscope images.N_(2) adsorption-desorption isotherms show no remarkably difference in specific surface areas between different preparation methods and Na-excess contents.The analysis of X-ray absorption near edge structure indicates that the oxidation states of Ni and Mn are+2 and+4,respectively.For the electrochemical properties,superior electrochemical performance is observed in the NNMO electrode with a low Na-excess content of 5wt%.The highest specific capacitance is 36.07 F·g^(-1)at0.1 A·g^(-1)in the NNMO electrode prepared by using the sol-gel method.By contrast,the NNMO electrode prepared using the electrospinning method with decreased Na-excess content shows excellent cycling stability of 100%after charge-discharge measurements for 300 cycles.Therefore,controlling the Na excess in the precursor together with the preparation method is important for improving the electrochemical performance of Na-based electrode materials in supercapacitors.

3-Turns教学法在实践共同体促进深度学习中的应用

在电气工程专业实践教学过程中凝练出由Turn up、Turn away、Turn back等环节组成的3-Turns教学法。经过多轮的实践应用,3-Turns教学法在实践共同体中提供了一个兼具解释性与可操作性的教学样例。研究发现,3-Turns教学法对实践共同体促进工科生深度学习起到了提质增效的作用;3-Turns教学法为工程实践学习情境的强化设计提供了理论依据与经验支持。该研究验证了基于3-Turns教学法的实践共同体促进工科生深度学习的有效性,为助力工科人才培养质量的持续提升做出了积极的探索与实践。

电液3-UPS/S并联稳定平台参数振动特性分析

针对电液3-UPS/S并联稳定平台驱动液压缸的压力脉动所产生的参数振动,建立了稳定平台的参数振动方程并利用多尺度法求解了主共振响应与组合共振响应的一次近似解;分析了主共振与组合共振响应特性以及振动幅值在初始工作空间内的变化规律,最后采用四阶龙格库塔法与模态试验对参数振动模型进行验证。结果表明:数值解与理论解之间的最大误差为4.20%,固有频率理论值与试验值之间的最大误差为4.66%,可验证参数振动模型的正确性。

Pr掺杂Sm_(0.5)Sr_(0.5)CoO_(3)阴极的性能研究

固体氧化物燃料电池(SOFC)因能量转换效率高,绿色无污染而备受关注。研究发现,钙钛矿结构的Sm_(0.5)Sr_(0.5)CoO_(3-δ)(SSC)是电子-离子混合导体,具有良好的氧还原活性,以及电导率高、极化电阻低等优点。为了探究镧系元素Pr掺杂对SSC阴极性能的影响,采用溶胶-凝胶法制备Pr_(x)Sm_(0.5-x)Sr_(0.5)CoO_(3)(x=0.1,0.2,0.3,0.4,0.5)阴极粉体,对其进行一系列表征和电化学性能测试。电化学阻抗谱(EIS)测试表明,当Pr掺杂量为0.3时,PSSC-30阴极在550~750℃范围内的极化电阻均小于其他掺杂量;在700℃时,全电池的功率密度达到最大,为311.06mW/cm^(2)。

LaCoO_(3)纳米粒子的制备、掺杂及丙酮敏感性能研究

为了开发新型的钙钛矿钴氧化物气敏材料,探究不同掺杂离子及掺杂量对LaCoO_(3)气敏性能的影响,以La(NO_(3))3·6H_(2)O、Co(NO_(3))3·6H_(2)O、丙烯酰胺、柠檬酸为主要原料,采用溶胶-凝胶法制备了钙钛矿结构的LaCoO_(3)及A位Ca^(2+)、Sr^(2+)掺杂的纳米粒子。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、红外光谱(IR)对样品的结构、形貌、半导体性质进行了表征,研究了不同掺杂量对LaCoO_(3)纳米粒子晶粒大小、活化能等的影响。结果表明,A位Ca^(2+)、Sr^(2+)掺杂可以增大LaCoO_(3)晶粒的生长活化能、抑制晶粒生长;对制得样品进行丙酮敏感性能测试后发现,Ca^(2+)、Sr^(2+)掺杂均可提高LaCoO_(3)对丙酮的响应能力,尤其是Ca^(2+)掺杂量为15%时,样品对2%体积分数丙酮的灵敏度可达97.83%。

α-MoO_(3)的结构形貌与其催化合成季戊四醇正辛酸酯的构效关系研究

通过溶胶-凝胶法制备一种用于季戊四醇(PER)和正辛酸(OTA)酯化合成季戊四醇正辛酸酯(POE)的α-MoO_(3)催化剂.采用XRD、SEM、XPS和FITR分析手段对α-MoO_(3)粉体进行了表征.结果表明,焙烧温度对α-MoO_(3)的晶相结构、表观形貌及催化性能的影响显著.当焙烧温度达到450℃时,催化剂为正交晶面结构(021)和(110)同时择优取向的α-MoO_(3),样品表面光洁平整、大小均匀、分散性好,同时表现出较高的催化活性.在适宜的反应条件下(T=200℃, t=4 h,酸醇摩尔比n(OTA)∶n(PER)=4.0∶1,催化剂用量n(α-MoO_(3)-450)∶n(PER)=0.005),PER转化率可达98.8%, POE的选择性可达100%.

Preparation and properties of nanocrystal SmBO_3 by nitrate-citrate sol-gel combustion method

Nanocrystal SmBO3 powders were synthesized by nitrate-citrate sol-gel combustion method. The phase evolution, morphologies and absorbency of the synthesized powders were characterized by X-ray diffraction （XRD）, Field emission scanning electronic microscope （FESEM）, Fourier transform infrared spectroscopy （FFIR） and UV-3101PC spectrophotometer （UVPC）, respectively. XRD and FESEM results showed that pure SmBO3 phase was obtained at 750 ℃, with an average original particle size of about 100 nm. FTIR showed that there were apparently concentrated absorbent peaks between 500 and 1400 cm^-1. Moreover, the reflectivity of the powders apparently decreased at the wavelength between 1.05 and 1.15 μm. Therefore, SmBO3 might be a kind of absorbent material for infrared laser.

Electrochemical performance of Al-substituted Li_3V_2(PO_4)_3 cathode materials synthesized by sol-gel method

The effect of Al-substitution on the electrochemical performances of Li3V2(PO4)3 cathode materials was studied.Samples with stoichiometric proportion of Li3AlxV2-x(PO4)3(x=0,0.05,0.10)were prepared by adding Al(NO3)3 in the raw materials of Li3V2(PO4)3.The XRD analysis shows that the Al-substituted Li3V2(PO4)3 has the same monoclinic structure as the un-substituted Li3V2(PO4)3.The SEM images show that Al-substituted Li3V2(PO4)3 has regular and uniform particles.The electrochemical measurements show that Al-substitution can improve the rate capability of cathode materials.The Li3Al0.05V1.95(PO4)3 sample shows the best high-rate performance.The discharge capacity at 1C rate is 119 mA·h/g with 30th capacity retention rate about 92.97%.The electrode reaction reversibility and electronic conductivity are enhanced,and the charge transfer resistance decreases through Al-substitution.The improved electrochemical performances of Al-substituted Li3V2(PO4)3 cathode materials offer some favorable properties for their commercial application.

Luminescence properties of red-emitting Ca_2Al_2SiO_7:Eu^(3+) nanoparticles prepared by sol-gel method

A series of red-emitting Ca2_xA12SiOT：xEu^3＋ （x = 1 mol.%-10 tool.%） phosphors were synthesized by the sol-gel method. The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2A12SiO7：Eu^3＋ phosphors were investigated. X-ray diffraction （XRD） profiles showed that all peaks could be attributed to the tetragonal Ca2A12SiO7 phase when the sample was annealed at 1000℃. Scanning electron microscopy （SEM） micrographs indicate that the phosphors have an irregularly rounded mor- phology with particles of about 200 nm. Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu^3＋-O^2- and f-f transitions within the 4f^6 configuration of Eu^3＋ ions, respectively. Emission spectra implied that the red luminescence could be attributed to the transitions from the ^5D0 excited level to the 7Fj （J = 0, 1, 2, 3, 4） levels of Eu3＋ions with the main electric dipole transition ^5D0→^7F2 （618 and 620 nm）, and Eu^3＋ ions prefer to occupy a lower symmetry site in the crystal lattice. Moreover, the photoluminescence （PL） intensity was strongly dependent on both the sintering temperature and doping concentration, and the highest PL intensity was observed at an Eu^3＋ concentration x = 7 mol.% after annealing at ll00℃. The obtained Ca2A12SiO7：Eu^＋3＋ phosphor may have potential application for the red lamp phosphor.

Preparation of Crack-free 3Y-TZP/Al_2O_3 Composite Ceramic Fiber by Electrolysis-sol-gel Method

Polycrystalline 3Y-TZP/Al2O3 tetragonal zirconia fiber was obtained by the pyrolysis of gel fibers using zirconium oxychloride octahydrate（ZOC） as the raw material. The spinnable zirconia sol was prepared by electrolyzing the zirco-nium oxychloride octahydrate（ZOC） solution in the presence of acetic acid and sugar（ sucrose, glucrose or fructose） , in which the molar ratios of CH3 COOH/ZOC and sugar/ZOC were 1.0-4.0 and 0.2-0.4, respectively. The pre- pared tetragonal zireonia fibers sintered at different temperatures showed smooth and crack-free surfaces with diame, ters of 5-10 μm. The addition of Al2O3 enhanced the sintering process and prevented the crystals from growing. Thermogravimetric analysis（TG）, X-ray diffraction （ XRD ）, Fourier transform infrared spectroscopy（FTIR）, and scanning electron microscope（SEM） techniques were used to characterize the prepared fibers.

Upconversion properties of Y_2O_3:Er films prepared by sol-gel method

Y2O3：Er^3＋ films were prepared by a simple sol-gel process. The structural properties of Y2O3：Er^3＋ films were characterized with X-ray diffraction, Fourier transform infrared spectroscopy and field emission scanning electron microscopy. The results indicated that the Y2O3：Er^3＋ films might have high upconversion efficiency because of their low vibrational energy. Under 785 and 980 nm laser excitation, the samples showed green （^2H11/2→^4I15/2, ^4S3/2→^4I15/2） and red （^4F9/2→^4I15/2） upconversion emissions. The upconversion mechanisms were studied in detail through laser power dependence. Excited state absorption and energy transfer process were discussed as possible upconversion mechanisms. The cross relaxation process in Er^3＋ was also investigated.

Preparation of LiTi_2(PO_4)_3 by the Sol-gel Method and Investigation of Its Formation Process

ＬｉＴｉ２（ＰＯ４）３ｃｅｒａｍｉｃｓｍａｙａｃｑｕｉｒｅａｈｉｇｈｅｌｅｃｔｒｉｃａｌｃｏｎｄｕｃｔｉｖｉｔｙｂｙｐａｒｔｉａｌｙｓｕｂｓｔｉｔｕｔｉｎｇｓｏｍｅＭ３＋ｉｏｎｓ（Ｍ＝Ａｌ，Ｓｃ，Ｙ，Ｌａ）ｆｏｒｔｈｅＴｉ４＋ｉｏｎｓｏｒｄｏｐｉｎｇ...

Synthesis of Long Afterglow Photoluminescent Materials Sr_2MgSi_2O_7∶Eu^(2+), Dy^(3+) by Sol-Gel Method

Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.

Progress in Research on Nanometer Al_2O_3 Fabricated by Sol-Gel Method

Nanometer Al_2O_3 is one of new types of functional materials with broad application and development prospects in the future. The basic principle and ways of nanometer Al_2O_3 fabricated using sol-gel technique were introduced, and the factors affecting nanometer Al_2O_3 fabricated using sol-gel method were analyzed. The progress in research on nanometer Al_2O_3 and the application fields of nanometer Al_2O_3 were reviewed. The existing problems and the problems prospect for nanometer Al_2O_3 were pointed out.

Preparation of Perovskite-Type Oxides La_(1-x)Sr_xFe_(1-y)Co_yO_3 Using EDTA Sol-Gel Method

Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method(N_2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.

Intense up-conversion emissions of yb3＋/Dy3＋ co-doped A12O3 nanopowders prepared by non-aqueous sol-gel method＊

yb3＋/Dy3＋ co-doped A1203 nanopowders have been prepared by the non-aqueous sol-gel method and their up- conversion photoluminescence spectra are measured under excitation by a 980-nm semiconductor laser. The results show that there are comparatively abundant spectra of up-conversion emissions centered at 378, 408, 527 and 543, and 663 nm, corresponding to 4C9/2→ 6H13/2, 4C9/2→ 6Hll/2, 4115/2 → 6H13/2, and 4F9/2 →6Hll/2 transitions of Dy3＋, respectively. Two-photon and three-photon processes are involved in ultraviolet, violet, green, and red up-conversion emissions. The energy transition between Yb3＋ and Dy3＋ is discussed.

Synthesis of nanocrystalline γ-Al_2O_3 by sol-gel and precipitation methods for methanol dehydration to dimethyl ether

The capability of sol-gel and conventional precipitation techniques for the synthesis of nanocrystalline γ-alumina was investigated. These catalysts were used for vapor-phase dehydration of methanol to dimethyl ether in a fixed-bed reactor under the same operating conditions （T = 300 ？C, P = 1 bar, LHSV = 2.8, 11.7, 26.1 h？1） and characterized by means of N2 adsorption-desorption, NH3-TPD, XRD, TGA and SEM techniques. According to the experimental results, the catalysts prepared using sol-gel method in non-aqueous medium showed better performance compared with those prepared by other methods.

Preparation of YAG:Ce^(3+) phosphor by sol-gel low temperature combustion method and its luminescent properties

YAG:Ce3+ phosphor was prepared by sol-gel low-temperature combustion method. The effects of the precursor properties and calcining temperature on the crystallization process, microscopic morphology and luminescent properties of phosphor were studied. The results indicate that the pure phase of YAG can be obtained at 800 ℃ by sol-gel low temperature combustion method, using citric acid as complexing agent. When the molar ratio of metal ion to citric acid is 2.0 and pH value is 2, the crystallinity increases and the phosphor particle size grows up gradually with the increase of the calcining temperature. The powders were characterized through thermal analysis, X-ray diffraction analysis and scanning electron microscope analysis. The excitation spectra of YAG:Ce3+ phosphor take on a double peak structure, and the peak value of the main excitation spectra occurs at 460 nm and that of the emission spectra is near 530 nm. With the gradual increase of the calcining temperature, the peak position of excitation and emission spectra remains basically unchanged, but its relative intensity increases gradually.

模板法合成g-C_(3)N_(4)基复合材料及其光催化性能的研究进展

石墨相氮化碳(g-C_(3)N_(4))作为一种新型非金属高聚物半导体,具有易于合成、无毒无害、耐酸碱腐蚀、环境亲和性好等性质。独特的层状结构赋予了其较高的比表面积,适中的禁带宽度给予了其较好的光催化性能,使得其在光催化领域受到了广泛的关注。然而,纯相g-C_(3)N_(4)存在着比表面积小、活性位点不足、载流子复合过快和氧化还原能力偏弱等缺点,制约了其光催化领域的有效应用。研究表明,使用模板诱导工艺对g-C_(3)N_(4)进行结构调控可以有效解决上述问题。综述了目前常用于制备石墨相氮化碳的模板法(即硬模板法、软模板法和生物模板法),扩展讨论了多相复合工艺的进展情况,并归纳总结了g-C_(3)N_(4)基材料在光催化降解、CO_(2)转化和制氢等方面的应用情况。