In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency poi...In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.展开更多
An X-band four-way combined GaN solid-state power amplifier module is fabricated based on a self- developed AlGaN/GaN HEMT with 2.5-mm gate width technology on SiC substrate. The module consists of an Al- GaN/GaN HEMT...An X-band four-way combined GaN solid-state power amplifier module is fabricated based on a self- developed AlGaN/GaN HEMT with 2.5-mm gate width technology on SiC substrate. The module consists of an Al- GaN/GaN HEMT, Wilkinson power hybrids, a DC-bias circuit and microstrip matching circuits. For the stability of the amplifier module, special RC networks at the input and output, a resistor between the DC power supply and a transistor gate at the input and 3λ/4 Wilkinson power hybrids are used for the cancellation of low frequency self-oscillation and crosstalk of each amplifier. Under Vds = 27 V, Vgs = -4.0 V, CW operating conditions at 8 GHz, the amplifier module exhibits a line gain of 5 dB with a power added efficiency of 17.9%, and an output power of 42.93 dBm; the power gain compression is 2 dB. For a four-way combined solid-state amplifier, the power combining efficiency is 67.5%. It is concluded that the reduction in combining efficiency results from the non-identical GaN HMET, the loss of the hybrid coupler and the circuit fabricating errors of each one-way amplifier.展开更多
Based on a self-developed A1GaN/GaN HEMT with 2.5 mm gate width technology on a SiC substrate, an X-band GaN combined solid-state power amplifier module is fabricated. The module consists of an AIGaN/GaN HEMT, Wilkins...Based on a self-developed A1GaN/GaN HEMT with 2.5 mm gate width technology on a SiC substrate, an X-band GaN combined solid-state power amplifier module is fabricated. The module consists of an AIGaN/GaN HEMT, Wilkinson power couplers, DC-bias circuit and microstrip line. For each amplifier, we use a bipolar DC power source. Special RC networks at the input and output and a resistor between the DC power source and the gate of the transistor at the input are used for cancellation of self-oscillation and crosstalk of low-frequency of each amplifier. At the same time, branches of length 3λ/4 for Wilkinson power couplers are designed for the elimination of self-oscillation of the two amplifiers. Microstrip stub lines are used for input matching and output matching. Under Vds = 27 V, Vgs = -4.0 V, CW operating conditions at 8 GHz, the amplifier module exhibits a line gain of 5.6 dB with power added efficiency of 23.4%, and output power of 41.46 dBm (14 W), and the power gain compression is 3 dB. Between 8 and 8.5 GHz, the variation of output power is less than 1.5 dB.展开更多
The new 1 kW power module for ADS project needs the optimization of cooling design including water flow and tunnel layout, and the water flow of three tons per hour was chosen to be a goal for a 20 kW power source.Acc...The new 1 kW power module for ADS project needs the optimization of cooling design including water flow and tunnel layout, and the water flow of three tons per hour was chosen to be a goal for a 20 kW power source.According to analysis from the insertion and integrated loss, about 24 modules were integrated into the rated power. Thus, every module has a cooling flow of 2.1 L/min for RF heat load and power supply loss, which is very hard to achieve if no special consideration and techniques. A new thermal simulation method was introduced for thermal analysis of cooling plate through CST multi-physics suite,especially for temperature of power LDMOS transistor.Some specific measures carried out for the higher heat transfer were also presented in this paper.展开更多
In this paper,we present the general design methods and parameter measurements of a 1-k W solidstate radio frequency(RF) power amplifier at 2856 MHz,for the soft X-ray free electron laser facility.Three-stage amplific...In this paper,we present the general design methods and parameter measurements of a 1-k W solidstate radio frequency(RF) power amplifier at 2856 MHz,for the soft X-ray free electron laser facility.Three-stage amplification with a 4-way combination is used.An RF switch module is integrated with the solid-state RF power amplifier to convert the continuous wave(CW) signal into pulse signal,with adjustable pulse width.The power gain is measured at 57.7 d B at 60 d Bm output.The RF phase noise,which is measured by the low-level RF system,is\0.015 degree(RMS),while the pulse frontier jitter is\5 ns.展开更多
In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined a...In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.展开更多
In view of the existing design challenges for Terahertz(THz)power amplifiers(PAs),the common design methods and the efforts of the State Key Laboratory of Millimeter Wave,Southeast University,China in the development ...In view of the existing design challenges for Terahertz(THz)power amplifiers(PAs),the common design methods and the efforts of the State Key Laboratory of Millimeter Wave,Southeast University,China in the development of silicon-based THz PAs,mainly including silicon-based PAs with operating frequencies covering 100–300 GHz,are summarized in this paper.Particularly,we design an LC-balun-based two-stage differential cascode PA with a center frequency of 150 GHz and an output power of 14 dBm.Based on a Marchand balun,we report a 220 GHz three-stage differential cascode PA with a saturated output power of 9.5 dBm.To further increase the output power of THz PA,based on a four-way differential power combining technique,we report a 211–263 GHz dual-LC-tank-based broadband PA with a recorded 14.7 dBm Psat and 16.4 dB peak gain.All the above circuits are designed in a standard 130 nm silicon germanium(SiGe)BiCMOS process.展开更多
Switch electro-hydraulic proportional amplifier(PA) widely employs single switch modulation power driving(SSMPD) or reverse discharging power driving(RDPD) at present. SSMPD has slow dynamic response, and can't...Switch electro-hydraulic proportional amplifier(PA) widely employs single switch modulation power driving(SSMPD) or reverse discharging power driving(RDPD) at present. SSMPD has slow dynamic response, and can't adjust independently the dither signal's amplitude and frequency; RDPD accelerates the current decay; consequently, it increases current ripple and power loss. For the purpose of solving the above mentioned problem, the tri-state modulation power driving(TSMPD) scheme was proposed for improving the performance of power driving. Detailedly, the hardware circuit for the tri-state modulation power driving is designed; the tri-state modulation algorithm is realized by digital signal processor(DSP). The tri-state modulation power driving is investigated by experiments, comparetive experiments among the single switch modulation power driving(SSMPD), reverse discharging power driving(RDPD), and the TSMPD are implemented, and the experimental results demonstrate that the linearity error of TSMDP meets the requirement of PA; the current response of TSMSP is the best; the amplitude of ripple current of the TSMPD can be reduced without increasing frequency of PWM, in addition, dither signal amplitude and frequency can be adjusted independently for each other. It is very meaningful to guide the development of high performance proportional amplifier for high frequency response proportional solenoid.展开更多
In memory polynomial predistorter design, the coefficient estimation algorithm based on normalized least mean square is sensitive to initialization parameters. A predistorter based on generalized normalized gradient d...In memory polynomial predistorter design, the coefficient estimation algorithm based on normalized least mean square is sensitive to initialization parameters. A predistorter based on generalized normalized gradient descent algorithm is proposed. The merit of the GNGD algorithm is that its learning rate provides compensation for the independent assumptions in the derivation of NLMS, thus its stability is improved. Computer simulation shows that the proposed predistorter is very robust. It can overcome the sensitivity of initialization parameters and get a better linearization performance.展开更多
To compensate for nonlinear distortion introduced by RF power amplifiers (PAs) with memory effects, two correlated models, namely an extended memory polynomial (EMP) model and a memory lookup table (LUT) model, ...To compensate for nonlinear distortion introduced by RF power amplifiers (PAs) with memory effects, two correlated models, namely an extended memory polynomial (EMP) model and a memory lookup table (LUT) model, are proposed for predistorter design. Two adaptive digital predistortion (ADPD) schemes with indirect learning architecture are presented. One adopts the EMP model and the recursive least square (RLS) algorithm, and the other utilizes the memory LUT model and the least mean square (LMS) algorithm. Simulation results demonstrate that the EMP-based ADPD yields the best linearization performance in terms of suppressing spectral regrowth. It is also shown that the ADPD based on memory LUT makes optimum tradeoff between performance and computational complexity.展开更多
The reliability of electronic device is threatened in high power microwave (HPM) environment. In accordance with the situation that the emulation is ineffective in evaluating the accuracy and precision of the HPM effe...The reliability of electronic device is threatened in high power microwave (HPM) environment. In accordance with the situation that the emulation is ineffective in evaluating the accuracy and precision of the HPM effect to electronic device, the experimental method is used to resolve the problem. Low Noise Amplifier (LNA) and Limiter are selected as the objects for the experiments, the structural characteristic of the front-end of radar receiver is described, the phenomena and criterion are elaborated and analyzed using injection method due to its ability to get an accurate threshold avoiding the complex coupling, the basic principle of injection experiment is demonstrated, and the method and process of effect experiment about Low Noise Amplifier and Limiter are also explained. The experimental system is established, and the system is composed of low power microwave source such as TWT, test equipment for obtaining the effect parameters, and some of auxiliary equipments as camera, optical microscope or electron microscopy, attenuator, detector, and directional coupler etc. The microwave delivered from source is adjusted to the power infused by attenuator, and pour in the decanting point of effecter via directional coupler, then the couple signal created by directional coupler is input to the recording instrument after detecting by detector, finally the power of effecter is obtained. The value of power, which damages the effecter in the microwave pulse environment, is classified at the index of sensitivity, and the threshold is obtained by power diagnose and wave test. Some regular understandings of the HPM effect to electronic device are obtained based on the results of the experiments. It turns out that the index of electronic device is influenced significantly by the energy via front door coupling, the MOSFET made up of GaAs is the most wearing part to HPM in LNA, the damage threshold of LNA is about 40dBm under single pulse while in repetitive pulse the value is from 33.3dBm to 43.9dBm according to different wave band. The damage threshold of Limiter is about 56dBm to80dBm.展开更多
This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency (RF) power amplifiers (PAs) as well as the use of these technologies in mobile broadb...This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency (RF) power amplifiers (PAs) as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking (ET) design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.展开更多
The vertical position of plasma in the HT-7U Tokamak is inherently unstable. In order to realize active stabilization, the response rate of the high-power high-frequency amplifier feeding the active control coils must...The vertical position of plasma in the HT-7U Tokamak is inherently unstable. In order to realize active stabilization, the response rate of the high-power high-frequency amplifier feeding the active control coils must be fast enough. This paper analyzes the paralleling scheme of the power amplifier through two kinds of control mode. One is the synchronous control; the other is the asynchronous control. Via the comparison of the two kinds of control mode, both of their characteristics are given in the text. At last, the analyzed result is verified by a small power experiment.展开更多
In this paper, a novel technique for power amplifier (PA) linearization is presented. The Legendre wavelet neural networks (LWNN) is first utilized to model PA and inverse structure of the PA by applying practical tra...In this paper, a novel technique for power amplifier (PA) linearization is presented. The Legendre wavelet neural networks (LWNN) is first utilized to model PA and inverse structure of the PA by applying practical transmission signals and the gradient descent algorithm is applied to estimate the coefficients of the LWNN. Secondly, this technique is implemented to identify and optimize the coefficient parameters of the proposed pre-distorter (PD), i.e., the inversion model of the PA. The proposed method is most efficient and the pre-distorter shows stability and effectiveness because of the rich properties of the LWNN. A quite significant improvement in linearity is achieved based on the measured data of the PA characteristics and out power spectrum has been compared.展开更多
In this letter, a novel model is proposed for modeling the nonlinearity and memory effects of power amplifiers. The classical Volterra model is modified through a function of the sum of nonlinearity order with sum of ...In this letter, a novel model is proposed for modeling the nonlinearity and memory effects of power amplifiers. The classical Volterra model is modified through a function of the sum of nonlinearity order with sum of memory length. The parameters of this model can be extracted in digital domain since the model is analyzed based on the envelope signals. The model we proposed enables a substantial reduction in the number of coefficients involved, and with excellent accuracy.展开更多
Quasi-PID control method that is able to effectively inhibit the inherent tracking error of PI control method is proposed on the basis of a rounded theoretical analysis of a model of switching power amplifiers (SPAs)....Quasi-PID control method that is able to effectively inhibit the inherent tracking error of PI control method is proposed on the basis of a rounded theoretical analysis of a model of switching power amplifiers (SPAs). To avoid the harmful impacts of the circuit parameter variations and the random disturbances on quasi-PID control method, a single neuron is introduced to endow it with self-adaptability. Quasi-PID control method and the single neuron combine with each other perfectly, and their formation is named as single-neuron adaptive quasi-PID control method. Simulation and experimental results show that single-neuron adaptive quasi-PID control method can accurately track both the predictable and the unpredictable waveforms. Quantitative analysis demonstrates that the accuracy of single-neuron adaptive quasi-PID control method is comparable to that of linear power amplifiers (LPAs) and so can fulfill the requirements of some high-accuracy applications, such as protective relay test. Such accuracy is very difficult to be achieved by many modern control methods for converter controls. Compared with other modern control methods, the programming realization of single-neuron adaptive quasi-PID control method is more suitable for real-time applications and realization on low-end microprocessors for its simple structure and lower computational complexity.展开更多
In this paper, an envelope Hammerstein (EH) model is introduced to describe dynamic input -output characteristics of RF power amplifiers. In the modeling approach, we use a new truncation method and an established n...In this paper, an envelope Hammerstein (EH) model is introduced to describe dynamic input -output characteristics of RF power amplifiers. In the modeling approach, we use a new truncation method and an established nonlinear time series method to determine model structure. Then, we discuss the process of model parameter extraction in detailed. Finally, a 2 W WCDMA power amplifier is measured to verify the performance of EH model, and good agreement between model output and measurement result shows our model can accurately predict output characteristic of the power amplifier.展开更多
This paper demonstrated a high power and high beam quality diode-pumped 1319-nm Nd:YAG master oscillator-power amplifier laser system. A thermally near-unstable resonator with four-rod birefringence compensation fiat...This paper demonstrated a high power and high beam quality diode-pumped 1319-nm Nd:YAG master oscillator-power amplifier laser system. A thermally near-unstable resonator with four-rod birefringence compensation fiat-fiat cavity was adopted as the master oscillator. A solid etalon was inserted in the unidirectional ring resonator to compress the laser linewidth. Under a repetition rate of 500 Hz and pulse width of 160 μs, the master oscillator delivers an average output power of 16.8 W at 1319 nm with linear polarisation, beam quality factor M^2=1.16 and linewidth of 3.2 GHz. A double-pass power amplifier with two amplifier stages was employed for higher power scaling and the output power was amplified to be 25.9 W with M^2 = 1.43.展开更多
A robust digital predistortion(DPD)technique utilizing negative feedback iteration is introduced for linearizing power amplifiers(PAs)in long term evolution(LTE)/5G systems.Different from the conventional direct learn...A robust digital predistortion(DPD)technique utilizing negative feedback iteration is introduced for linearizing power amplifiers(PAs)in long term evolution(LTE)/5G systems.Different from the conventional direct learning and indirect learning structure,the proposed DPD suggests a two-step method to identify the predistortion.Firstly,a negative feedback based iteration is used to estimate the optimal DPD signal.Then the corresponding DPD parameters are extracted by forward modeling with the input signal and optimal DPD signal.The iteration can be applied to both single-band and dual-band PAs,which will achieve superior linear performance than the conventional direct learning DPD while having a relatively low computational complexity.The measurement is carried out on a broadband Doherty PA(DPA)with a 200 MHz bandwidth LTE signal at 2.1 GHz,and on a 5G DPA with two 10 MHz LTE signals at 3.4/3.6 GHz for validation in dual-band scenarios.展开更多
RF power amplifiers (PAs) are usually considered as memoryless devices in most existing predistortion techniques. Nevertheless, in wideband communication systems, PA memory effects can no longer be ignored and memoryl...RF power amplifiers (PAs) are usually considered as memoryless devices in most existing predistortion techniques. Nevertheless, in wideband communication systems, PA memory effects can no longer be ignored and memoryless predistortion cannot linearize PAs effectively. After analyzing PA memory effects, a novel predistortion method based on wavelet networks (WNs) is proposed to linearize wideband RF power amplifiers. A complex wavelet network with tapped delay lines is applied to construct the predistorter and then a complex backpropagation algorithm is developed to train the predistorter parameters. The simulation results show that compared with the previously published feed-forward neural network predistortion method, the proposed method provides faster convergence rate and better performance in reducing out-of-band spectral regrowth.展开更多
基金supported by National Natural Science Foundation of China(No.62001061)。
文摘In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.
基金supported by the National Natural Science Foundation of China(Nos.60736033,60676048).
文摘An X-band four-way combined GaN solid-state power amplifier module is fabricated based on a self- developed AlGaN/GaN HEMT with 2.5-mm gate width technology on SiC substrate. The module consists of an Al- GaN/GaN HEMT, Wilkinson power hybrids, a DC-bias circuit and microstrip matching circuits. For the stability of the amplifier module, special RC networks at the input and output, a resistor between the DC power supply and a transistor gate at the input and 3λ/4 Wilkinson power hybrids are used for the cancellation of low frequency self-oscillation and crosstalk of each amplifier. Under Vds = 27 V, Vgs = -4.0 V, CW operating conditions at 8 GHz, the amplifier module exhibits a line gain of 5 dB with a power added efficiency of 17.9%, and an output power of 42.93 dBm; the power gain compression is 2 dB. For a four-way combined solid-state amplifier, the power combining efficiency is 67.5%. It is concluded that the reduction in combining efficiency results from the non-identical GaN HMET, the loss of the hybrid coupler and the circuit fabricating errors of each one-way amplifier.
基金Project supported by the National Natural Science Foundation of China (Nos.60736033,60676048)
文摘Based on a self-developed A1GaN/GaN HEMT with 2.5 mm gate width technology on a SiC substrate, an X-band GaN combined solid-state power amplifier module is fabricated. The module consists of an AIGaN/GaN HEMT, Wilkinson power couplers, DC-bias circuit and microstrip line. For each amplifier, we use a bipolar DC power source. Special RC networks at the input and output and a resistor between the DC power source and the gate of the transistor at the input are used for cancellation of self-oscillation and crosstalk of low-frequency of each amplifier. At the same time, branches of length 3λ/4 for Wilkinson power couplers are designed for the elimination of self-oscillation of the two amplifiers. Microstrip stub lines are used for input matching and output matching. Under Vds = 27 V, Vgs = -4.0 V, CW operating conditions at 8 GHz, the amplifier module exhibits a line gain of 5.6 dB with power added efficiency of 23.4%, and output power of 41.46 dBm (14 W), and the power gain compression is 3 dB. Between 8 and 8.5 GHz, the variation of output power is less than 1.5 dB.
基金supported by the ‘‘strategic priority research program’’ of the Chinese Academy of Sciences(No.XDA030205)
文摘The new 1 kW power module for ADS project needs the optimization of cooling design including water flow and tunnel layout, and the water flow of three tons per hour was chosen to be a goal for a 20 kW power source.According to analysis from the insertion and integrated loss, about 24 modules were integrated into the rated power. Thus, every module has a cooling flow of 2.1 L/min for RF heat load and power supply loss, which is very hard to achieve if no special consideration and techniques. A new thermal simulation method was introduced for thermal analysis of cooling plate through CST multi-physics suite,especially for temperature of power LDMOS transistor.Some specific measures carried out for the higher heat transfer were also presented in this paper.
文摘In this paper,we present the general design methods and parameter measurements of a 1-k W solidstate radio frequency(RF) power amplifier at 2856 MHz,for the soft X-ray free electron laser facility.Three-stage amplification with a 4-way combination is used.An RF switch module is integrated with the solid-state RF power amplifier to convert the continuous wave(CW) signal into pulse signal,with adjustable pulse width.The power gain is measured at 57.7 d B at 60 d Bm output.The RF phase noise,which is measured by the low-level RF system,is\0.015 degree(RMS),while the pulse frontier jitter is\5 ns.
基金supported by National Natural Science Foundations of China (No.61971052 and No.U20A20203)Key Research and Development Project of Guangdong Province (2020B0101080001)
文摘In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.
基金supported in part by the National Natural Science Foundation of China under Grant Nos.62101117 and 62188102in part by ZTE Industry-University-Institute Cooperation Fundsin part by the Project funded by China Postdoctoral Science Foundation under Grant Nos.2021M700763 and 2022T150113.
文摘In view of the existing design challenges for Terahertz(THz)power amplifiers(PAs),the common design methods and the efforts of the State Key Laboratory of Millimeter Wave,Southeast University,China in the development of silicon-based THz PAs,mainly including silicon-based PAs with operating frequencies covering 100–300 GHz,are summarized in this paper.Particularly,we design an LC-balun-based two-stage differential cascode PA with a center frequency of 150 GHz and an output power of 14 dBm.Based on a Marchand balun,we report a 220 GHz three-stage differential cascode PA with a saturated output power of 9.5 dBm.To further increase the output power of THz PA,based on a four-way differential power combining technique,we report a 211–263 GHz dual-LC-tank-based broadband PA with a recorded 14.7 dBm Psat and 16.4 dB peak gain.All the above circuits are designed in a standard 130 nm silicon germanium(SiGe)BiCMOS process.
基金supported by National Basic Research and Development Program of China (973 Program, Grant No. 2007CB714000)National Natural Science Foundation of China (Grant No. 50875233)
文摘Switch electro-hydraulic proportional amplifier(PA) widely employs single switch modulation power driving(SSMPD) or reverse discharging power driving(RDPD) at present. SSMPD has slow dynamic response, and can't adjust independently the dither signal's amplitude and frequency; RDPD accelerates the current decay; consequently, it increases current ripple and power loss. For the purpose of solving the above mentioned problem, the tri-state modulation power driving(TSMPD) scheme was proposed for improving the performance of power driving. Detailedly, the hardware circuit for the tri-state modulation power driving is designed; the tri-state modulation algorithm is realized by digital signal processor(DSP). The tri-state modulation power driving is investigated by experiments, comparetive experiments among the single switch modulation power driving(SSMPD), reverse discharging power driving(RDPD), and the TSMPD are implemented, and the experimental results demonstrate that the linearity error of TSMDP meets the requirement of PA; the current response of TSMSP is the best; the amplitude of ripple current of the TSMPD can be reduced without increasing frequency of PWM, in addition, dither signal amplitude and frequency can be adjusted independently for each other. It is very meaningful to guide the development of high performance proportional amplifier for high frequency response proportional solenoid.
基金supported by the National High Technology Research and Development Program of China(2006AA01Z270).
文摘In memory polynomial predistorter design, the coefficient estimation algorithm based on normalized least mean square is sensitive to initialization parameters. A predistorter based on generalized normalized gradient descent algorithm is proposed. The merit of the GNGD algorithm is that its learning rate provides compensation for the independent assumptions in the derivation of NLMS, thus its stability is improved. Computer simulation shows that the proposed predistorter is very robust. It can overcome the sensitivity of initialization parameters and get a better linearization performance.
文摘To compensate for nonlinear distortion introduced by RF power amplifiers (PAs) with memory effects, two correlated models, namely an extended memory polynomial (EMP) model and a memory lookup table (LUT) model, are proposed for predistorter design. Two adaptive digital predistortion (ADPD) schemes with indirect learning architecture are presented. One adopts the EMP model and the recursive least square (RLS) algorithm, and the other utilizes the memory LUT model and the least mean square (LMS) algorithm. Simulation results demonstrate that the EMP-based ADPD yields the best linearization performance in terms of suppressing spectral regrowth. It is also shown that the ADPD based on memory LUT makes optimum tradeoff between performance and computational complexity.
文摘The reliability of electronic device is threatened in high power microwave (HPM) environment. In accordance with the situation that the emulation is ineffective in evaluating the accuracy and precision of the HPM effect to electronic device, the experimental method is used to resolve the problem. Low Noise Amplifier (LNA) and Limiter are selected as the objects for the experiments, the structural characteristic of the front-end of radar receiver is described, the phenomena and criterion are elaborated and analyzed using injection method due to its ability to get an accurate threshold avoiding the complex coupling, the basic principle of injection experiment is demonstrated, and the method and process of effect experiment about Low Noise Amplifier and Limiter are also explained. The experimental system is established, and the system is composed of low power microwave source such as TWT, test equipment for obtaining the effect parameters, and some of auxiliary equipments as camera, optical microscope or electron microscopy, attenuator, detector, and directional coupler etc. The microwave delivered from source is adjusted to the power infused by attenuator, and pour in the decanting point of effecter via directional coupler, then the couple signal created by directional coupler is input to the recording instrument after detecting by detector, finally the power of effecter is obtained. The value of power, which damages the effecter in the microwave pulse environment, is classified at the index of sensitivity, and the threshold is obtained by power diagnose and wave test. Some regular understandings of the HPM effect to electronic device are obtained based on the results of the experiments. It turns out that the index of electronic device is influenced significantly by the energy via front door coupling, the MOSFET made up of GaAs is the most wearing part to HPM in LNA, the damage threshold of LNA is about 40dBm under single pulse while in repetitive pulse the value is from 33.3dBm to 43.9dBm according to different wave band. The damage threshold of Limiter is about 56dBm to80dBm.
文摘This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency (RF) power amplifiers (PAs) as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking (ET) design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.
基金The project supported by the National Meg-Science Engineering Project of Chinese Goverment
文摘The vertical position of plasma in the HT-7U Tokamak is inherently unstable. In order to realize active stabilization, the response rate of the high-power high-frequency amplifier feeding the active control coils must be fast enough. This paper analyzes the paralleling scheme of the power amplifier through two kinds of control mode. One is the synchronous control; the other is the asynchronous control. Via the comparison of the two kinds of control mode, both of their characteristics are given in the text. At last, the analyzed result is verified by a small power experiment.
文摘In this paper, a novel technique for power amplifier (PA) linearization is presented. The Legendre wavelet neural networks (LWNN) is first utilized to model PA and inverse structure of the PA by applying practical transmission signals and the gradient descent algorithm is applied to estimate the coefficients of the LWNN. Secondly, this technique is implemented to identify and optimize the coefficient parameters of the proposed pre-distorter (PD), i.e., the inversion model of the PA. The proposed method is most efficient and the pre-distorter shows stability and effectiveness because of the rich properties of the LWNN. A quite significant improvement in linearity is achieved based on the measured data of the PA characteristics and out power spectrum has been compared.
文摘In this letter, a novel model is proposed for modeling the nonlinearity and memory effects of power amplifiers. The classical Volterra model is modified through a function of the sum of nonlinearity order with sum of memory length. The parameters of this model can be extracted in digital domain since the model is analyzed based on the envelope signals. The model we proposed enables a substantial reduction in the number of coefficients involved, and with excellent accuracy.
文摘Quasi-PID control method that is able to effectively inhibit the inherent tracking error of PI control method is proposed on the basis of a rounded theoretical analysis of a model of switching power amplifiers (SPAs). To avoid the harmful impacts of the circuit parameter variations and the random disturbances on quasi-PID control method, a single neuron is introduced to endow it with self-adaptability. Quasi-PID control method and the single neuron combine with each other perfectly, and their formation is named as single-neuron adaptive quasi-PID control method. Simulation and experimental results show that single-neuron adaptive quasi-PID control method can accurately track both the predictable and the unpredictable waveforms. Quantitative analysis demonstrates that the accuracy of single-neuron adaptive quasi-PID control method is comparable to that of linear power amplifiers (LPAs) and so can fulfill the requirements of some high-accuracy applications, such as protective relay test. Such accuracy is very difficult to be achieved by many modern control methods for converter controls. Compared with other modern control methods, the programming realization of single-neuron adaptive quasi-PID control method is more suitable for real-time applications and realization on low-end microprocessors for its simple structure and lower computational complexity.
文摘In this paper, an envelope Hammerstein (EH) model is introduced to describe dynamic input -output characteristics of RF power amplifiers. In the modeling approach, we use a new truncation method and an established nonlinear time series method to determine model structure. Then, we discuss the process of model parameter extraction in detailed. Finally, a 2 W WCDMA power amplifier is measured to verify the performance of EH model, and good agreement between model output and measurement result shows our model can accurately predict output characteristic of the power amplifier.
基金Project supported by the National High Technology Research and Development Program and the National Natural Science Foundation of China (Grant No. 60508013)
文摘This paper demonstrated a high power and high beam quality diode-pumped 1319-nm Nd:YAG master oscillator-power amplifier laser system. A thermally near-unstable resonator with four-rod birefringence compensation fiat-fiat cavity was adopted as the master oscillator. A solid etalon was inserted in the unidirectional ring resonator to compress the laser linewidth. Under a repetition rate of 500 Hz and pulse width of 160 μs, the master oscillator delivers an average output power of 16.8 W at 1319 nm with linear polarisation, beam quality factor M^2=1.16 and linewidth of 3.2 GHz. A double-pass power amplifier with two amplifier stages was employed for higher power scaling and the output power was amplified to be 25.9 W with M^2 = 1.43.
基金National Key R&D Program of China under Grant No.2018YFB1801603 and No.2017YFF0206201National Sci⁃ence and Technology Major Project under Grant 2017ZX03001024,NSFC under Grant No.61801259 and Beijing National Research Center for Infor⁃mation Science and Technology(BNRist).
文摘A robust digital predistortion(DPD)technique utilizing negative feedback iteration is introduced for linearizing power amplifiers(PAs)in long term evolution(LTE)/5G systems.Different from the conventional direct learning and indirect learning structure,the proposed DPD suggests a two-step method to identify the predistortion.Firstly,a negative feedback based iteration is used to estimate the optimal DPD signal.Then the corresponding DPD parameters are extracted by forward modeling with the input signal and optimal DPD signal.The iteration can be applied to both single-band and dual-band PAs,which will achieve superior linear performance than the conventional direct learning DPD while having a relatively low computational complexity.The measurement is carried out on a broadband Doherty PA(DPA)with a 200 MHz bandwidth LTE signal at 2.1 GHz,and on a 5G DPA with two 10 MHz LTE signals at 3.4/3.6 GHz for validation in dual-band scenarios.
基金Project (No. 60372026) supported by the National Natural ScienceFoundation of China
文摘RF power amplifiers (PAs) are usually considered as memoryless devices in most existing predistortion techniques. Nevertheless, in wideband communication systems, PA memory effects can no longer be ignored and memoryless predistortion cannot linearize PAs effectively. After analyzing PA memory effects, a novel predistortion method based on wavelet networks (WNs) is proposed to linearize wideband RF power amplifiers. A complex wavelet network with tapped delay lines is applied to construct the predistorter and then a complex backpropagation algorithm is developed to train the predistorter parameters. The simulation results show that compared with the previously published feed-forward neural network predistortion method, the proposed method provides faster convergence rate and better performance in reducing out-of-band spectral regrowth.