Study on the Attack of Molten Silicates on Plasma-Sprayed Thermal Barrier Coatings

Thermal barrier coating (TBC) revolutionized the industry by allowing higher operating temperatures for equipment, such as gas turbines in the aeronautical industry. However, at high temperatures, the TBC is exposed to the attack of molten silicates, known as CMAS (Calcium-Magnesium-Alumino-Silicate), which are particles from the environment that infiltrate the TBC, causing delamination. In this study, samples coated with TBC by thermal spray and covered with CMAS were evaluated at temperatures of 1200˚C and 1250˚C. For each temperature, exposure times of 1 h and 5 h were used. Samples with longer exposure time had a considerable volume increase. The main contribution of this work was to demonstrate the non-wettability of the CMAS, even in the 5-h heat treatments, which prevented its infiltration in the deeper regions. The conditions to guarantee the formation of the silicate and its consequent wettability are also discussed.

Spray pyrolysis feasibility of tungsten substitution for cobalt in nickel-rich cathode materials

Cobalt(Co)serves as a stabilizer in the lattice structure of high-capacity nickel(Ni)-rich cathode materials.However,its high cost and toxicity still limit its development.In general,it is possible to perform transition metal substitution to reduce the Co content.However,the traditional coprecipitation method cannot satisfy the requirements of multielement coprecipitation and uniform distribution of elements due to the differences between element concentration and deposition rate.In this work,spray pyrolysis was used to prepare LiNi_(0.9)Co_(0.1-x)W_(x)O_(2)(LNCW).In this regard,the pyrolysis behavior of ammonium metatungstate was analyzed,together with the substitu-tion of W for Co.With the possibility of spray pyrolysis,the Ni-Co-W-containing oxide precursor presents a homogeneous distribution of metal elements,which is beneficial for the uniform substitution of W in the final materials.It was observed that with W substitution,the size of primary particles decreased from 338.06 to 71.76 nm,and cation disordering was as low as 3.34%.As a consequence,the pre-pared LNCW exhibited significantly improved electrochemical performance.Under optimal conditions,the lithium-ion battery assembled with LiNi_(0.9)Co_(0.0925)W_(0.0075)O_(2)(LNCW-0.75mol%)had an improved capacity retention of 82.7%after 200 cycles,which provides insight in-to the development of Ni-rich low-Co materials.This work presents that W can compensate for the loss caused by Co deficiency to a cer-tain extent.

HVOF-sprayed HAp/S53P4 BG composite coatings on an AZ31 alloy for potential applications in temporary implants

Bioactive thermal spray coatings produced via high-velocity oxygen fuel spray(HVOF)from hydroxyapatite(HAp)and bioactive glasses(BG)have the potential to be employed on temporary implants due to the ability of both HAp and BG to dissolve and promote osseointegration,considering that both phases have different reaction and dissolution rates under in-vitro conditions.In the present work,75%wt.HAp-25%wt.S53P4 bioactive glass powders were HVOF-sprayed to obtain HAp/S53P4 BG composite coatings on a bioresorbable AZ31 alloy.The study is focused on exploring the effect of the stand-off distance and fuel/oxygen ratio variation as HVOF parameters to obtain stable structural coatings and to establish their effect on the phases and microstructure produced in those coatings.Different characterization techniques,such as scanning electron microscopy,X-ray diffraction,and Fourier transform infrared spectroscopy,were employed to characterize relevant structural and microstructural properties of the composite coatings.The results showed that thermal gradients during coating deposition must be managed to avoid delamination due to the high temperature achieved(max 550℃)and the differences in coefficients of thermal expansion.It was also found that both spraying distance and oxygen/fuel ratio allowed to keep the hydroxyapatite as the main phase in the coatings.In addition,in-vitro electrochemical studies were performed on the obtained HAp/S53P4 BG composite coatings and compared against the uncoated AZ31 alloy.The results showed a significant decrease in hydrogen evolution(at least 98%)when the bioactive coating was applied on the Mg alloy during evaluation in simulated body fluid(SBF).

Experimental investigation on effective aerosol scavenging using different spray configurations with pre-injection of water mist for Fukushima Daiichi decommissioning

During the decommissioning of the Fukushima Daiichi nuclear power plant,it is important to consider the retrieval of resolidified debris both in air and underwater configurations.For the subsequent retrieval of debris from the reactor building,the resolidified debris must be cut into smaller pieces using various cutting methods.During the cutting process,aerosol particles are expected to be generated at the submicron scale.It has been noted that such aerosols sizing within the Greenfield gap(0.1-1μm)are difficult to remove effectively using traditional spraying methods.Therefore,to improve the aerosol removal efficiency of the spray system,a new aerosol agglomeration method was recently proposed,which involves injecting water mist to enlarge the sizes of the aerosol particles before removing them using water sprays.In this study,a series of experiments were performed to clarify the proper spray configurations for effective aerosol scavenging and to improve the performance of the water mist.The experimental results showed that the spray flow rate and droplet characteristics are important factors for the aerosol-scavenging efficiency and performance of the water mist.The results obtained from this study will be helpful for the optimization of the spray system design for effective aerosol scavenging during the decommissioning of the Fukushima Daiichi plant.

Simulation Study on the Heat Transfer Characteristics of a Spray-Cooled Single-Pipe Cooling Tower

The current study focuses on spray cooling applied to the heat exchange components of a cooling tower.An optimization of such processes is attempted by assessing different spray flow rates and droplet sizes.For simplicity,the heat exchanger of the cooling tower is modeled as a horizontal round tube and a cooling tower spray cooling model is developed accordingly using a computational fluid dynamics(CFD)software.The study examines the influence of varying spray flow rates and droplet sizes on the heat flow intensity between the liquid layer on the surface of the cylindrical tube and the surrounding air,taking into account the number of nozzles.It is observed that on increasing the spray flow strength,the heat flow intensity and extent of the liquid film in the system are enhanced accordingly.Moreover,the magnitude of droplet size significantly impacts heat transfer.A larger droplet size decreases evaporation in the air and enhances the deposition of droplets on the round tube.This facilitates the creation of the liquid film and enhances the passage of heat between the liquid film and air.Increasing the number of nozzles,while maintaining a constant spray flow rate,results in a decrease in the flow rate of each individual nozzle.This decrease is not favorable in terms of heat transfer.

Preparation and Properties of Spray Polyurea Elastomer for Aquaculture Foam Floating Balls

[Objectives] This study was conducted to develop a polyurea elastomer which can be sprayed on the surface of expanded polystyrene (EPS) floating balls, so as to improve the surface strength and service life of the floating balls. [Methods] The effects of the types and amounts of isocyanate, chain extenders and polyether polyols on the gelation rate, adhesion and wear resistance of polyurea elastomer were investigated, and it was finally determined the preparation process of polyurea elastomer using liquid isophorone diisocyanate (IPDI) and amino-terminated polyether (D2000) as the main raw materials, dimethylthiotoluene diamine (E300) as the chain extender and silica as the wear resistance modifier through two-step solution polymerization of prepolymerization and chain extension. [Results] The physical properties and chemical resistance tests of spray polyurea elastomer showed that it had good physical properties and acid and alkali resistance, and could meet the requirements of spraying and protection of EPS floating ball surface in marine environment. [Conclusions] Polyurea elastomer coating can improve the aging resistance, wear resistance and acid and alkali resistance of EPS floating balls, and prevent them from being fragile and floating randomly to form marine floating garbage which results in "white pollution".

Effect of Spray Rails on Takeoff Performance of Amphibian Aircraft

Amphibian aircraft have seen a rise in popularity in the recreational and utility sectors due to their ability to take off and land on both land and water, thus serving a myriad of purposes, such as aerobatics, surveillance, and firefighting. Such seaplanes must be aerodynamically and hydrodynamically efficient, particularly during the takeoff phase. Naval architects have long employed innovative techniques to optimize the performance of marine vessels, including incorporating spray rails on hulls. This research paper is dedicated to a comprehensive investigation into the potential utilization of spray rails to enhance the takeoff performance of amphibian aircraft. Several spray rail configurations obtained from naval research were simulated on a bare Seamax M22 amphibian hull to observe an approximate 10% - 25% decrease in water resistance at high speeds alongside a 3% reduction in the takeoff time. This study serves as a motivation to improve the design of the reference airplane hull and a platform for detailed investigations in the future to improve modern amphibian design.

Designing an Experimental Device for Swinging Excitation Spray Cooling

In this paper,we introduce the design principle of the oscillating excited spray cooling experimental device.We then designed an oscillating excited spray cooling experimental device.By using the device,the swaying motion can be realized through the control system,and the motion of the droplet under different vibration frequencies can be observed.By measuring the liquid flow rate and pressure,the changes in liquid flow rate,pressure,and temperature with time under different vibration frequencies were studied.The trajectory of the droplet and the temperature distribution of the droplet under different vibration frequencies could be observed.The device has a simple structure,is easy to control,and can achieve continuous observation of the spray cooling process.

Effect of TiO_2 content on properties of Al_2O_3 thermal barrier coatings by plasma spraying

Al2O3 thermal barrier coatings with different TiO2 contents were deposited on 6061 aluminum alloy by plasma spraying. The corrosion resistance, thermal insulation property and phase composition of these coatings were investigated. The results indicate that all the feedstock powders exhibit phase transformation during the spray process. With the increase of the TiO2 content in the powder, the corrosion resistance of the coating is enhanced but the thermal insulation property is decreased. This can be attributed to the higher thermal conductivity but lower melting point and brittleness of TiO2 than those of Al2O3, so it is easy for TiO2 to disperse in the brittle Al2O3 substrate during spraying, in which these dispersively distributed TiO2 play the role of hole sealing, releasing stress and reducing cracks.

Premature failure induced by non-equilibrium grain-boundary tantalum segregation in air-plasma sprayed ZrO_(2)-YO_(1.5)-TaO_(2.5)thermal barrier coatings

ZrO_(2)-YO_(1.5)-TaO_(2.5)(ZYTO)is a promising top-coat material for thermal barrier coatings(TBCs).The bulk properties of ZYTO have been reported by several studies,but its performances as TBCs are less-well understood.In this work,ZYTO TBCs were prepared by air plasma spraying(APS)and their thermal cycling performances were investigated at 1150℃.Despite of the good bulk properties,APS ZYTO TBCs present an extremely short thermal fatigue life.This is attributed to the non-equilibrium grain-boundary segregation of TaO_(2.5) induced by limited solubility and rapid quenching during APS process,resulting in a tetragonal(t)to cubic(c)and metastable-tetragonal(tm)phase transformation in ZYTO TBCs.The volume shrinkage(~0.74vol%)of phase transformation leads to many cracks at the c/tm phase boundaries after deposition.On the other hand,the formation of cubic phase with massive grain-boundary Ta segregation induces a large intergranular embrittlement and a weak bonding strength(~5.3 MPa),resulting in the premature failure of the ZYTO TBCs.

Investigation on plasma-sprayed ZrO_2 thermal barrier coating on nickel alloy substrate

The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY Y 2O 3 stabilized ZrO 2 transition layer and Y 2O 3 stabilized ZrO 2 ceramic layer are prepared on nickel alloy substrates using the plasma spray technique. The relationship among the composition, structure and property of the coatings are investiga ted by means of optical microscope, scanning electronic microscope and the experiments of thermal shock resistance cycling and high temperature oxidation resistance. The results show that the structure design of introdu cing a transition layer between Ni alloy substrate and ZrO 2 ceramic coating guarantees the high quality and properties of the coatings; ZrO 2 coatings doped with a little SiO 2 possesses better thermal shock resistance and more excellent hot corrosion resistance as compared with ZrO 2 coating materials without SiO 2 ;the improvement in performance of ZrO 2 coating doped with SiO 2 is due to forming more dense coating structure by self closing effects of the flaws and pores in the ZrO 2 coatings.

Microstructural features and properties of plasma sprayed YPSZ/NiCrAlY thermal barrier coating (TBC)

The plasma sprayed thermal barrier coating (TBC) consists of NiCrAlY bond coating and yttria partially stabilized zirconia (YPSZ) top coating. NiCrAlY coating mainly contains Ni solid solution with face centered cubic lattice, Al_2O_3 oxides and pores. The most obvious feature of YPSZ coating with tetragonal zirconia is a lot of vertical microcracks in this coating. The thermal insulation capability of the TBC increased with an increase in YPSZ coating thickness, the temperature drop across the TBC increasing from 60℃ to 92℃ with increasing YPSZ coating thickness from 100 μm to 500 μm. The thermal shock resistance of the TBC decreased with increasing YPSZ coating thickness and cracks initiated mainly in original vertical microcrack tips of the YPSZ coating and propagated not only along YPSZ coating/ NiCrAlY coating interface but also through NiCrAlY coating. The oxidation process of the TBC at 1 200℃ can be divided into two stages: transient oxidation stage with rapid oxidation rate and steady oxidation stage with slow oxidation. Their transition time was about 10 hours. The weight gain for 100 hours was 3.222 mg/mm2. It is favorable to increase YPSZ coating toughness and to decrease the pores and oxides of the TBC system for improving thermal shock resistance and oxidation resistance of the TBC.

Research on fabricating Fe base amorphous alloy by bar plasma spraying

Since amorphous alloys have wider application, they can not be fabricated using the conventional cooling velocity. The bar material plasma spraying is adopted to fabricate, Fe base amorphous alloy in this investigation. The crystallization degree, microstructure, micro-hardness, composition, crystallization temperature of the amorphous alloy and the flying rules of the atomized particles in the process of the plasma spray are tested. The results show that the alloy prepared has the high amorphous degree and homogeneous microstructure, micro-hardness and the crystallization temperature can reach 1 187 HV and 531 ℃ respectively. The atomization is very well during the process of plasma spraying; and there is high thermal gradient, the cooling velocity reaches 6.07 × 10^7 K/s.

Characterization of functionally graded ZrO_2 thermal barrier coatings sprayed by supersonic plasma spray with dual powder feed ports

The functionally graded thermal barrier coatings （FG-TBCs） with 80%ZrO2-13%CeO2-7%Y2O3 （C-YSZ）/NiCoCrAlY were prepared using a recently developed supersonic plasma spraying（S-PS） with dual powder feed ports system. The thermal shock experiment of FG-TBCs specimens was carried out by means of the automatic thermal cycle device, in which the samples were heated to 1200℃ by oxygen-acetylene flame jet then water-quenched to ambient temperature. The temperature—time curves of specimens and photographs can be watched on-line and recorded by a computer during the test. The results show that the totally 1mm-thick FG-TBCs have excellent thermal shock resistance due to the fact that the coatings have no any peeling-off after 200 thermal cycles. The microstructures and morphologies of FG-TBCs were characterized and analyzed by SEM.

Influence of Spray Gun Position and Orientation on Liquid Film Development along a Cylindrical Surface

A method combining computationalfluid dynamics(CFD)and an analytical approach is proposed to develop a prediction model for the variable thickness of the spray-induced liquidfilm along the surface of a cylindrical workpiece.The numerical method relies on an Eulerian-Eulerian technique.Different cylinder diameters and positions and inclinations of the spray gun are considered and useful correlations for the thickness of the liquidfilm and its distribution are determined using various datafitting algorithms.Finally,the reliability of the pro-posed method is verified by means of experimental tests where the robot posture is changed.The provided cor-relation are intended to support the optimization of spray-based coating applications.

Residual stress with asymmetric spray quenching for thick aluminum alloy plates

Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.

Enhancing energetic performance of metal-organic complex-based metastable energetic nanocomposites by spray crystallization

Energetic metal-organic complexes have been involved in nanothermites as novel oxidants.However,the existing preparation methods often lead to mixing inhomogeneity and small contact area of ingredients,the reactivity and functionality of the novel energetic nanocomposites are still limited.In this work,spray crystallization(SC)method was used to prepare novel energetic nanocomposites,the high-energy metal-organic complex[Ni(CHZ)_(3)](ClO_(4))_(2)(CHZ=1,3-diaminourea)was composited with nanoaluminum(n-Al).Results showed that n-Al/[Ni(CH_(2))_(3)](ClO_(4))_(2)energetic nanocomposites prepared by SC method increased heat release to 2977.6 J/g and peak pressure to 3.91 MPa with higher pressurization rate(1324.06 MPa/s),decreased sensitivity thresholds(>100 mJ)to electrostatic discharge(ESD)and enhanced detonation ability compared with[Ni(CHZ)_(3)](ClO_(4))_(2)alone and physically mixed(PM)n-Al/[Ni(CHZ)_(3)](ClO_(4))_(2).These results proved that it is significant to introduce energetic metal-organic complexes with inherent high energy in new-concept n-Al/energetic metal-organic complexes nanocomposites through SC method for a better performance of its application.

The Influence of Sea Sprays on Drag Coefficient at High Wind Speed

Field and laboratory observations indicate that the variation of drag coefficient with wind speed at high winds is different from that under low-to-moderate winds.By taking the effects of wave development and sea spray into account,a new parameterization of drag coefficient applicable from low to extreme winds is proposed.It is shown that,under low-to-moderate wind conditions so that the sea spray effects could be neglected,the nondimensional aerodynamic roughness first increases and then decreases with the increasing wave age;whereas under high wind conditions,the drag coefficient decreases with the increasing wind speed due to the modification of the logarithmic wind profile by the effect of sea spray droplets produced by bursting bubbles or wind tearing breaking wave crests.The drag coefficients and sea surface aerodynamic roughnesses reach their maximum values vary under different wave developments.Correspondingly,the reduction of drag coefficient under high winds reduces the increasing rate of friction velocity with increasing wind speed.

Sea spray induced air-sea heat and salt fluxes based on the wavesteepnessdependent sea spray model

Sea spray,which comprises amounts of small ocean droplets,plays a significant role in the air-sea coupling,atmospheric and oceanic dynamics,and climate.However,it remains arduous to arrive at estimates for the efficiency and accuracy of the sea spray induced air-sea heat and salt fluxes.This is because the microphysical process of sea spray evolution in the air is of extreme complexity.In this study,we iteratively calculated the sea spray induced air-sea heat and salt fluxes at various weather condition.To do so,we implemented one novel wave-steepness-dependent sea spray model into a bulk air-sea fluxes algorithm and utilized other sea spray models as comparisons.Based on the improved wave-dependent bulk turbulent algorithm,we observed that despite the negative contribution of sea spray to the sensible heat fluxes,the sea spray positively contributes to the air-sea latent heat fluxes,leading to an overall increase in the total air-sea heat fluxes.The additional heat fluxes caused by sea spray may be the missing critical process that can clarify the discrepancies observed between measured and modelled Tropical Cyclone’s development and intensification.In addition to heat fluxes,we observed that sea spray has significant impacts on the air-sea salt fluxes.As the sea salt particles are one of the main sources of the atmosphere aerosol,our results imply that sea spray could impact global and regional climate.Thus,given the significance of sea spray on the air-sea boundary layer,sea spray effects need to be considered in studies of air-sea interaction,dynamics of atmosphere and ocean.

Experimental study on the improvement of spray characteristics of aero-engines using gliding arc plasma

A gliding arc plasma fuel atomization actuator suitable for aeroengines was designed,and a gliding arc plasma fuel spray experimental platform was built to address the fuel atomization problem in aeroengine combustion chambers.The spray characteristics for different airflows,fuel flows,and discharge voltages were analyzed using laser particle size analysis.The research shows that the fuel atomization effect is improved from the increased airflow.The decreased fuel flow not only reduces the injection pressure of the fuel but also changes the discharge mode of the gliding arc,which affects reductions in the discharge power and inhibits fuel atomization.Gliding arc discharges accelerate the breaking,atomization,and evaporation of fuel droplets while reducing the particle size,which increases the proportion of small droplets.Compared with the working conditions of plasma-assisted atomization without the gliding arc,the D0.5,D0.9,and average particle size of the fuel droplets are reduced by 4.7%,6.5%,and 4.1%,respectively,when the modulation voltage of the gliding arc power supply is 200 V.