Preparation and Characterization of SrTiO_3 Thin Film on Functional Organic Self-Assembled Monolayers

SrTiO3 thin film was successfully prepared on the functionalized organic self-assembled monolayers（SAMs） by the Liquid Phase Deposition（LPD） method.The as-prepared samples were characterized by X-ray diffraction（XRD）,atomic force microscope（AFM）,scanning electron microscopy（SEM） and metallographic microscope.Measurement of contact angle showed that the hydrophobe substrate was changed into hydrophile by UV irradiation.AFM photographs of octadecyl-trichloro-silane self-assembled monolayer（OTS-SAM） surface approved that UV irradiation did change the morphology of OTS monolayer and provided evidence for the conversion of hydrophilic characteristic.Photographs of Metallographic Microscope showed that OTS-SAM had an active effect on the deposition of SrTiO3 thin film.XRD and SEM indicated that the thin film was of pure cubic phase SrTiO3 and composed of nanosized grains with a size in the range of 100-500 nm.The formation mechanism of the SrTiO3 film was proposed.

Dielectric and Structural Properties of SrTiO_3 Thin Films Grown by Laser Molecular Beam Epitaxy

Here I will review recent progress on the study of dielectric SrTiO3 （STO） thin films. In our work, laser molecular beam epitaxy has been used to prepare multilayer heterostructures consisting of dielectric STO and high temperature superconducting YBa2Cu3Oy （YBCO） thin films for tunable applications. Since the tunability of the dielectric constant and dielectric loss of STO are the key parameters determining the performance of tunable devices and hence the feasibility of this technology, the correlations between the deposition parameters of STO thin films, their structural characteristics, and dielectric properties were studied. An enhanced tunability of 74.7%, comparable to that of STO single-crystal, was observed in our grown STO thin films suitable for tunable YBCO applications. On the other hand, we have grown epitaxial STO （110） films on Si without any buffer layer. The nature of epitaxial growth and interfacial structures of the grown films were examined by various techniques, such as Laue diffraction, high-resolution transmission electron microscopy （HRTEM） and x-ray photoelectron spectroscopy. The in-plane alignments for the STO （110） films grown directly on Si （100） was found as STO//Si and STO//Si . HRTEM study has showed a crystalline transition across the STO/Si interface, indicating it is free from any amorphous oxide layer. We provide clear evidence that the interface mainly consists of Sr silicate phase. The results suggest that such Sr silicate interfacial layer exhibits favourable structural and chemical properties that are particularly useful for epitaxial STO （110） growth on Si. Such STO thin films will be useful for practical applications.

Reversible alternation between bipolar and unipolar resistive switching in La-SrTiO_3 thin films

The alternation from bipolar to unipolar resistive switching is observed in perovskite La0.01Sr0.99TiO3 thin films. These two switching modes can be activated separately depending on the compliance current （Icomp） during the electroforming process： with a higher Icomp （5 mA） the unipolar resistance switching behavior is measured, while the bipolar resistance switching behavior is observed with a lower Icomp （1 mA）. On the basis of I–V characteristics, the switching mechanisms for the URS and BRS modes are considered as being a change in the Schottky-like barrier height and/or width at the Pt/La-SrTiO3 interface and the formation and disruption of conduction filaments, respectively.

Structure,ferroelectric,and enhanced fatigue properties of sol–gel-processed new Bi-based perovskite thin films of Bi(Cu_(1/2)Ti_(1/2))O_(3)–PbTiO_(3)

Bi-based perovskite ferroelectric thin films have wide applications in electronic devices due to their excellent ferroelectric properties.New Bi-based perovskite thin films Bi(Cu_(1/2)Ti_(1/2))O_(3)–PbTiO_(3)(BCT–PT) are deposited on Pt(111)/Ti/SiO_(2)/Si substrates in the present study by the traditional sol–gel method.Their structures and related ferroelectric and fatigue characteristics are studied in-depth.The BCT–PT thin films exhibit good crystallization within the phase-pure perovskite structure,besides,they have a predominant(100) orientation together with a dense and homogeneous microstructure.The remnant polarization(2P_(r)) values at 30 μC/cm^(2) and 16 μC/cm^(2) are observed in 0.1BCT–0.9PT and 0.2BCT–0.8PT thin films,respectively.More intriguingly,although the polarization values are not so high,0.2BCT–0.8PT thin films show outstanding polarization fatigue properties,with a high switchable polarization of 93.6% of the starting values after 10^(8) cycles,indicating promising applications in ferroelectric memories.

Enhanced Electrical Properties of Bi_(2−x)Sb_(x)Te_(3) Nanoflake Thin Films Through Interface Engineering

The structure–property relationship at interfaces is difficult to probe for thermoelectric materials with a complex interfacial microstructure.Designing thermoelectric materials with a simple,structurally-uniform interface provides a facile way to understand how these interfaces influence the transport properties.Here,we synthesized Bi_(2−x)Sb_(x)Te_(3)(x=0,0.1,0.2,0.4)nanoflakes using a hydrothermal method,and prepared Bi_(2−x)Sb_(x)Te_(3) thin films with predominantly(0001)interfaces by stacking the nanoflakes through spin coating.The influence of the annealing temperature and Sb content on the(0001)interface structure was systematically investigated at atomic scale using aberration-corrected scanning transmission electron microscopy.Annealing and Sb doping facilitate atom diffusion and migration between adjacent nanoflakes along the(0001)interface.As such it enhances interfacial connectivity and improves the electrical transport properties.Interfac reactions create new interfaces that increase the scattering and the Seebeck coefficient.Due to the simultaneous optimization of electrical conductivity and Seebeck coefficient,the maximum power factor of the Bi_(1.8)Sb_(0.2)Te_(3) nanoflake films reaches 1.72 mW m^(−1)K^(−2),which is 43%higher than that of a pure Bi_(2)Te_(3) thin film.

Numerical Analysis on the Effect of n-Si on Cu(In, Ga)Se2 Based Thin-Films for High-Performance Solar Cells by 1D-SCAPS

We report the performances of a chalcopyrite Cu(In, Ga)Se2 CIGS-based thin-film solar cell with a newly employed high conductive n-Si layer. The data analysis was performed with the help of the 1D-Solar Cell Capacitance Simulator (1D-SCAPS) software program. The new device structure is based on the CIGS layer as the absorber layer, n-Si as the high conductive layer, i-In2S3, and i-ZnO as the buffer and window layers, respectively. The optimum CIGS bandgap was determined first and used to simulate and analyze the cell performance throughout the experiment. This analysis revealed that the absorber layer’s optimum bandgap value has to be 1.4 eV to achieve maximum efficiency of 22.57%. Subsequently, output solar cell parameters were analyzed as a function of CIGS layer thickness, defect density, and the operating temperature with an optimized n-Si layer. The newly modeled device has a p-CIGS/n-Si/In2S3/Al-ZnO structure. The main objective was to improve the overall cell performance while optimizing the thickness of absorber layers, defect density, bandgap, and operating temperature with the newly employed optimized n-Si layer. The increase of absorber layer thickness from 0.2 - 2 µm showed an upward trend in the cell’s performance, while the increase of defect density and operating temperature showed a downward trend in solar cell performance. This study illustrates that the proposed cell structure shows higher cell performances and can be fabricated on the lab-scale and industrial levels.

Thickness effect on solar-blind photoelectric properties of ultrathinβ-Ga_(2)O_(3)films prepared by atomic layer deposition

Theβ-Ga_(2)O_(3)films with different thicknesses are prepared by an atomic layer deposition system.The influence of film thickness on the crystal quality is obvious,indicating that the thicker films perform better crystal quality,which is verified from x-ray diffraction(XRD)and scanning electron microscope(SEM)results.The Ga_(2)O_(3)-based solar blind photodetectors with different thicknesses are fabricated and studied.The experimental results show that the responsivity of the photodetectors increases exponentially with the increase of the film thickness.The photodetectors with inter-fingered structure based on 900 growth cyclesβ-Ga_(2)O_(3)active layers(corresponding film thickness of 58 nm)exhibit the best performances including a low dark current of 134 fA,photo-to-dark current ratio of 1.5×10^(7),photoresponsivity of 1.56 A/W,detectivity of 2.77×10^(14)Jones,and external quantum efficiency of 764.49%at a bias voltage of 10 V under 254-nm DUV illumination.The photoresponse rejection ratio(R_(254)/R_(365))is up to 1.86×10^(5).In addition,we find that the photoelectric characteristics also depend on the finger spacing of the MSM structure.As the finger spacing decreases from 50μm to10μW,the photoresponsivity,detectivity,and external quantum efficiency increase significantly.

XPS Study of Electroless Deposited Sb2Se3 Thin Films for Solar Cell Absorber Material

As a thin film solar cell absorber material, antimony selenide (Sb2Se3) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb2Se3 thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.

Corrosion characteristics of single-phase Mg-3Zn alloy thin film for biodegradable electronics

Biodegradable metals as electrodes, interconnectors, and device conductors are essential components in the emergence of transient electronics, either for passive implants or active electronic devices, especially in the fields of biomedical electronics. Magnesium and its alloys are strong candidates for biodegradable and implantable conducting materials because of their high conductivity and biocompatibility, in addition to their well-understood dissolution behavior. One critical drawback of Mg and its alloys is their considerably high dissolution rates originating from their low anodic potential, which disturbs the compatibility to biomedical applications. Herein, we introduce a single-phase thin film of a Mg-Zn binary alloy formed by sputtering, which enhances the corrosion resistance of the device electrode, and verify its applicability in biodegradable electronics. The formation of a homogeneous solid solution of single-phase Mg-3Zn was confirmed through X-ray diffraction and transmission electron microscopy. In addition, the dissolution behavior and chemistry was also investigated in various biological fluids by considering the effect of different ion species. Micro-tensile tests showed that the Mg-3Zn alloy electrode exhibited an enhanced yield strain and elongation in relation to a pure Mg electrode. Cell viability test revealed the high biocompatibility rate of the Mg-3Zn binary alloy thin film. Finally, the fabrication of a wireless heater demonstrated the integrability of biodegradable electrodes and highlighted the ability to prolong the lifecycle of thermotherapy-relevant electronics by enhancing the dissolution resistance of the Mg alloy.

Depth Profile Study of Electroless Deposited Sb2S3 Thin Films Using XPS for Photovoltaic Applications

Sb2S3 has gained tremendous research recently for thin film solar cell absorber material because of their easy synthesis, unique electrical and optical properties. The stoichiometry and composition of electroless Sb2S3 thin films were analyzed using XPS depth profile studies. The surface layers were found nearly stoichiometric. On the other hand, the inner layer was rich in antimony composition making it more conductive electrically.

Investigation of Sprayed Lu2O3 Thin Films Using XPS

Spray pyrolysis method was used to deposit Lutetium Oxide (Lu2O3) thin films using lutetium (III) chloride as source material and water as oxidizer. Annealing was carried out in argon atmosphere at 450°C for 60 minutes of the films. To investigate the composition and stoichiometry of sprayed as-deposited and annealed Lu2O3 thin films, depth profile studies using X-ray photoelectron spectroscopy (XPS) was done. Nearly stoichiometric was observed for both annealed and as-deposited films in inner and surface layers.

XPS Depth Profile Study of Sprayed Ga2O3 Thin Films

Ga2O3 thin films were fabricated by spray pyrolysis method using gallium acetylacetonate as source material and water as oxidizer. The films were annealed at 450°C for 60 minutes in argon atmosphere. X-ray photoelectron spectroscopy (XPS) depth profile studies were carried out to analyze the stoichiometry and composition of sprayed as-deposited and annealed Ga2O3 thin films. Surface layers and the inner layers of as-deposited and annealed films were found nearly stoichiometric.

Transfer film effects induced by 3D-printed polyether-ether-ketone with excellent tribological properties for joint prosthesis

Based on the building principle of additive manufacturing,printing orientation mainly determines the tribological properties of joint prostheses.In this study,we created a polyether-ether-ketone(PEEK)joint prosthesis using fused filament fabrication and investigated the effects of printing orientation on its tribological properties using a pin-on-plate tribometer in 25% newborn calf serum.An ultrahigh molecular weight polyethylene transfer film is formed on the surface of PEEK due to the mechanical capture of wear debris by the 3D-printed groove morphology,which is significantly impacted by the printing orientation of PEEK.When the printing orientation was parallel to the sliding direction of friction,the number and size of the transfer film increased due to higher steady stress.This transfer film protected the matrix and reduced the friction coefficient and wear rate of friction pairs by 39.13%and 74.33%,respectively.Furthermore,our findings provide a novel perspective regarding the role of printing orientation in designing knee prostheses,facilitating its practical applications.

Preparation,Characterization and Photothermal Study of PVA/Ti_(2)O_(3) Composite Films

In this work,flexible photothermal PVA/Ti_(2)O_(3) composite films with different amount(0 wt%,5 wt%,10 wt%,15 wt%)of Ti_(2)O_(3) particles modified by steric acid were prepared by a simple solution casting method.The microstructures,XRD patterns,FTIR spectra,UV-Vis-NIR spectra thermo-conductivity,thermo-stability and photothermal effects of these composite films were all characterized.These results indicated that Ti_(2)O_(3) particles were well dispersed throughout the polyvinyl alcohol(PVA)matrix in the PVA/Ti_(2)O_(3) composite films.And Ti_(2)O_(3) particles could also effectively improve the photothermal properties of the composite films which exhibited high light absorption and generated a high temperature(about 57.4℃for film with 15 wt%Ti_(2)O_(3) amount)on the surface when it was irradiated by a simulated sunlight source(1 kW/m^(2)).

Identifying the enhancement mechanism of Al/MoO_(3) reactive multilayered films on the ignition ability of semiconductor bridge using a one-dimensional gas-solid two-phase flow model

Energetic Semiconductor bridge(ESCB)based on reactive multilayered films(RMFs)has a promising application in the miniature and intelligence of initiator and pyrotechnics device.Understanding the ignition enhancement mechanism of RMFs on semiconductor bridge(SCB)during the ignition process is crucial for the engineering and practical application of advanced initiator and pyrotechnics devices.In this study,a one-dimensional(1D)gas-solid two-phase flow ignition model was established to study the ignition process of ESCB to charge particles based on the reactivity of Al/MoO_(3) RMFs.In order to fully consider the coupled exothermic between the RMFs and the SCB plasma during the ignition process,the heat release of chemical reaction in RMFs was used as an internal heat source in this model.It is found that the exothermal reaction in RMFs improved the ignition performance of SCB.In the process of plasma rapid condensation with heat release,the product of RMFs enhanced the heat transfer process between the gas phase and the solid charge particle,which accelerated the expansion of hot plasma,and heated the solid charge particle as well as gas phase region with low temperature.In addition,it made up for pressure loss in the gas phase.During the plasma dissipation process,the exothermal chemical reaction in RMFs acted as the main heating source to heat the charge particle,making the surface temperature of the charge particle,gas pressure,and gas temperature rise continuously.This result may yield significant advantages in providing a universal ignition model for miniaturized ignition devices.

Bipolar Resistive Switching in Epitaxial Mn_3O_4 Thin Films on Nb-Doped SrTiO_3 Substrates

Spinel （O01）-orientated Mn304 thin films on Nb-doped SrTi03 （001） substrates are fabricated via the pulsed laser deposition method. X-ray diffraction and high-resolution transmission electron microscopy indicate that the as-prepared epitaxial fihn is well crystaiHzed. In the film plane the orientation relationship between the film and the substrate is [lOOjMn3 04 ｜｜[110] Nb-doped SrTiO3. After an electroforming process, the film shows bipolar nonvolatile resistance switching behavior. The positive voltage bias drives the sample into a low resistance state, while the negative voltage switches it back to a high resistance state. The switching polarity is different from the previous studies. The complex impedance measurement suggests that the resistance switching behavior is of filament type. Due to the performance reproducibility and state stability, Mn3O4 might be a promising candidate for the resistive random access memory devices.

The third-order optical nonlinearity of the stainless steel doped SrTiO_3 thin film grown by L-MBE

Stainless steel-doped SrTiO3 thin films were fabricated by laser molecular beam epitaxy (L-MBE). Nonlinear optical property of the thin film was measured by the single beam Z-scan technique at the wavelength of 532 nm. Two two-phonon absorption coefficient and nonlinear refractive index were determined to be 9.37 x 10-7 m/W and 1.55 x 10-6 esu, respectively. The merit figure T was calculated to be 1.8, satisfying condition T < 1 for an optical switch. The thin film has a very promising prospect for the applications in optical device.

Target effects on electrical properties and laser induced voltages of La_(0.72)Ca_(0.28)MnO_3 thin films prepared by pulsed laser deposition

La0.72Ca0.28MnO3 thin films were deposited on untilted and 15° tilted LaAlO_3 （100） single crystalline substrates by pulsed laser deposition. The polycrystalline targets used in the deposition process were synthesized by sol-gel and coprecipitation methods, respectively. The structure, electrical transport properties and surface morphology of the targets and films were studied. It is found that, compared with coprecipitation method, the sol-gel target has more homogeneous components and larger density and grain size, thus the higher insulator-metal transition temperature and larger temperature coefficient of resistivity. The thin film prepared by sol-gel target has a uniform grain size and higher quality. The metal-insulator transition temperature is higher and the laser induced voltage signal is larger. Preparing the target by sol-gel method can largely improve the properties of corresponding thin films in pulsed laser deposition process.

Effects of Atomic Oxygen Irradiation on Transparent Conductive Oxide Thin Films

Transparent conductive oxide （TCO） thin film is a kind of functional material which has potential applications in solar cells and atomic oxygen （AO） resisting systems in spacecrafts. Of TCO, ZnO：Al （ZAO） and In2O3：Sn （ITO） thin films have been widely used and investigated. In this study, ZAO and ITO thin films were irradiated by AO with different amounts of fluence. The as-deposited samples and irradiated ones were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and Hall-effect measurement to investigate the dependence of the structure, morphology and electrical properties of ZAO or ITO on the amount of fluence of AO irradiation. It is noticed that AO has erosion effects on the surface of ZAO without evident influences upon its structure and conductive properties. Moreover, as the amount of AO fluence rises, the carrier concentration of ITO decreases causing the resistivity to increase by at most 21.7%.

Preparation and properties of tungsten-doped indium oxide thin films

Tungsten-doped indium oxide (IWO) thin films were deposited on glass substrate by DC reactive magnetron sputtering. The effects of sputtering power and growth temperature on the structure, surface morphology, optical and electrical properties of IWO thin films were investigated. The thickness and surface morphology of the films are both closely dependent on the sputtering power and the substrate temperature. The transparency of the films decreases with the increase of the sputtering power but is not seriously influenced by substrate temperature. All the IWO thin film samples have high transmittance in near-infrared spectral range. With either the sputtering power or the growth temperature increases, the resistivity of the film decreases at the beginning and increases after the optimum parameters. The as-deposited IWO films with minimum resistivity of 6.4 10 4 cm were obtained at a growth temperature of225 C and sputteringpower of 40 W, with carrier mobility of 33.0 cm 2 V 1 s 1 and carrier concentration of 2.8 10 20 cm 3 and the average transmittance of about 81% in near-infrared region and about 87% in visible region.