Blasting induced dynamic stress concentration and failure characteristics of deep-buried rock tunnel

In this study,the dynamic stress concentration factors(DSCF)around a straight-wall arch tunnel(SWAT)were solved analytically utilizing the complex variable function methods and Duhamel’s integral.The effects of wavelength,incident angle,and blasting rising time on the DSCF distribution were analyzed.Theoretical results pointed out dynamic disturbances resulting in compressive stress concentration in the vertical direction and tensile stress in the incident direction.As the wavelength and rising time increased,there was a tendency for the amplitude of stress concentration to initially rise and then converge.Moreover,a series of 3D FEM models were established to evaluate the effect of different initial stress states on the dynamic failure of the tunnel surrounding rock.The results indicated that the failure of the surrounding rock was significantly influenced by the direction of the static maximum principal stress and the direction of the dynamic disturbance.Under the coupling of static and blasting loading,damage around the tunnel was more prone to occur in the dynamic and static stress concentration coincidence zone.Finally,the damage modes of rock tunnel under static stress and blasting disturbance from different directions were summarized and a proposed support system was presented.The results reveal the mechanisms of deep-buried rock tunnel destruction and dynamically triggered rockburst.

Nonlinear Static Finite Element Stress Analysis of Pipe-in-Pipe Risers

Owing to the complexity of the pipe-in-pipe (PIP) riser system in structure, load and restraint, many problems arise in the structural analysis of the system. This paper presents a new method for nonlinear static finite element stress analysis of the PIP riser system. The finite element (FE) model of the PIP riser system is built via software AutoPIPE 6.1. According to the specialties of a variety of components in the PIP riser system, different elements are used so as to model the system accurately. Allowing for the complication in modeling the effects of seabed restraint, a technique based on the bilinear spring concept is developed to calculate the soil properties. Then, based on a pipeline project, the entire procedure of stress analysis is discussed in detail, including creation of an FE model, processing of input data and analysis of results. A wide range of loading schemes is investigated to ascertain that the stresses remain within the acceptable range of the pipe material strength. Finally, the effects of the location of flanges, the thermal expansion of submarine pipelines and the seabed restraint on stress distribution in the riser and expansion loop are studied, which are valuable for pipeline designers.

STRESS ANALYSIS OF INJECTION MOLDED PARTS IN POST-FILLING STAGE

The linear isothermo-viscoelastic constitutive equation is established according to the principle of viscoelastic mechanics. Given the boundary conditions of the temperature field, the linear thermo-viscoelastic constitutive equation is established acording to the analysis of the thermorheologically simple. The stress analysis model is constructed on the base of some reasonable hypotheses which consider the restraint conditions of mold and the characteristics of injection molding in the post-filling stage. The mathematical model is calculated by the finite difference method. The results can help to predict the warpage of plastic products.

Stress analysis of functionally graded rotating discs: analytical and numerical solutions

This study deals with stress analysis of annular rotating discs made of functionally graded materials（FGMs）.Elasticity modulus and density of the discs are assumed to vary radially according to a power law function,but the material is of constant Poisson＇s ratio.A gradient parameter n is chosen between 0 and 1.0.When n = 0,the disc becomes a homogeneous isotropic material.Tangential and radial stress distributions and displacements on the disc are investigated for various gradient parameters n by means of the diverse elasticity modulus and density by using analytical and numerical solutions.Finally,a homogenous tangential stress distribution and the lowest radial stresses along the radius of a rotating disc are approximately obtained for the gradient parameter n = 1.0 compared with the homogeneous,isotropic case n = 0.This means that a disc made of FGMs has the capability of higher angular rotations compared with the homogeneous isotropic disc.

Analysis of interlaminar stress and nonlinear dynamic response for composite laminated plates with interfacial damage

By considering the effect of interfacial damage and using the variation principle, three-dimensional nonlinear dynamic governing equations of the laminated plates with interfacial damage are derived based on the general sixdegrees-of-freedom plate theory towards the accurate stress analysis. The solutions of interlaminar stress and nonlinear dynamic response for a simply supported laminated plate with interfacial damage are obtained by using the finite difference method, and the results are validated by comparison with the solution of nonlinear finite element method. In numerical calculations, the effects of interfacial damage on the stress in the interface and the nonlinear dynamic response of laminated plates are discussed.

ANALYSIS OF INTER-LAMINAR STRESSES FOR COMPOSITE LAMINATED PLATE WITH INTERFACIAL DAMAGE

A constitutive model for composite laminated plates with the damage effect of the intra-layers and inter-laminar interface is presented. The model is based on the general six-degrees-of-freedom plate theory, the discontinuity of displacement on the interfaces are depicted by three shape functions, which are formulated according to solutions satisfying three equilibrium equations, By using the variation principle, the three-dimensional non-linear equilibrium differential equations of the laminated plates with two different damage models are derived. Then, considering a simply supported laminated plate with damage, an analytical solution is presented using finite difference method to obtain the inter-laminar stresses.

Stress Analysis of the Subsea Dynamic Riser BaseProcess Piping

Thesubsea dynamic riser base （SDRB） is an important piece of equipment for the floating production platform mooring system.One end is connected to the rigid pipeline, carrying a rigid pipeline thermal expansion load and the other end is connected to a flexible riser, carrying the dynamic load of the flexible riser, so its function is a transition connection between the flexible riser and the rigid pipeline which fixes the flexible riser on the seabed. On the other hand. as a typical subsea product, the design will satisfythe requirements of the standards for subsea products. By studying the stress analysisphilosophy of the topside piping and subsea pipeline, a physical model and procedure for piping stress analysis of the SDRB have been established.The conditions of the adverse design load have been considered, and a combination of the static load from the rigid pipeline and the dynamic load flexibility has also been optimized. And a comparative analysis between the AMSE, DNV and API standards for piping stress with the checking rules has been done.Because theSDRB belongs to the subsea pipeline terminal product, the use of DNV standards to check its process piping stress is recommended. Finally, the process piping stress of the SDRB has been calculated, and the results show that the jacket pipe and the carrier pipe stress of the SDRB process piping satisfy the DNV standards as a whole.The bulkhead cannot be accurately simulated by the AutoPIPE software which uses the FEA software ANSYS inthe detailed analysis, but the checking results will still meet the requirements of the DNV standards.

Three dimensional finite element analysis of acetabulum loaded by static stress and its biomechanical significance

Objective:To explore the mechanical behavior of acetabulum loaded by static stress and provide the mechanical basis for clinical analysis and judgement on acetabular mechanical distribution and effect of static stress.Methods:By means of computer simulation, acetabular three dimensional model was input into three dimensional finite element analysis software ANSYS7.0. The acetabular mechanical behavior was calculated and the main stress value, stress distribution and acetabular unit displacement in the direction of main stress were analyzed when anterior wall of acetabulum and acetabular crest were loaded by 1 000 N static stress. Results:When acetabular anterior wall loaded by X direction and Z direction composition force, the stress passed along 4 directions: (1)from acetabular anterior wall to pubic symphysis along superior branch of pubis firstly, (2)from acetabular anterior wall to cacroiliac joint along pelvic ring,(3)in the acetabulum,(4)from the suffered point to ischium. When acetabular crest loaded by X direction and Y direction composition force, the stress transmitted to 4 directions: (1)from acetabular crest to ilium firstly, (2)from suffered point to cacroiliac joint along pelvic ring,(3) in the acetabulum ,(4)along the pubic branch,but no stress transmitted to the ischium branch.Conclusion:Analyzing the stress distribution of acetabulum and units displacement when static stress loaded can provide internal fixation point for acetabular fracture treatment and help understand the stress distribution of acetabulum.

Pore pressure fluctuations of overlying aquifer during residual coal mining and water-soil stress coupling analysis

Three test models and a simulation model were constructed based on the prevailing conditions of the Taiping coalmine in order to analyze pore pressure fluctuations of an overlying aquifer during residual coal mining. As well, the relation between pore pressure and soil stress was evaluated. The model tests show the vibrations of pore pressure and soil stress as a result of mining activities. The simulation model tells of the response characteristics of pore pressure after mining and its distribution in the sand aquifer. The comparative analysis reveals that pore pressure and soil stress vibration are activated by unexpected events occurring in mines, such as collapsing roofs. An increased pore pressure zone always lies above the wall in front or behind the working face of a mine. Both pore pressure and vertical stress result in increasing and decreasing processes during movements of the working face of a mine. The vibration of pore pressure always precedes soil stress in the same area and ends with a sharp decline. Changes in pore pressure of sand aquifer are limited to the area of stress changes. Obvious changes are largely located in a very small frame over the mining face.

Stress and buckling analysis of a thick-walled micro sandwich panel with a flexible foam core and carbon nanotube reinforced composite (CNTRC) face sheets

In this paper,the stresses and buckling behaviors of a thick-walled mi-cro sandwich panel with a flexible foam core and carbon nanotube reinforced composite(CNTRC)face sheets are considered based on the high-order shear deformation theory(HSDT)and the modified couple stress theory(MCST).The governing equations of equi-librium are obtained based on the total potential energy principle.The effects of various parameters such as the aspect ratio,elastic foundation,temperature changes,and volume fraction of the canbon nanotubes(CNTs)on the critical buckling loads,normal stress,shear stress,and deflection of the thick-walled micro cylindrical sandwich panel consider-ing different distributions of CNTs are examined.The results are compared and validated with other studies,and showing an excellent compatibility.CNTs have become very use-ful and common candidates in sandwich structures,and they have been extensively used in many applications including nanotechnology,aerospace,and micro-structures.This paper also extends further applications of reinforced sandwich panels by providing the modified equations and formulae.

TWO-DIMENSIONAL STRESS WAVE ANALYSIS IN INCOMPRESSIBLE ELASTIC SOLIDS

Two-dimensional stress wares in n general incompressible elastic solid are investigated. First, baxic equations for simple wares and shock waves are presented for a general strain energy junction. Then the characteristic ware speeds and the associated characteristic vectors are deduced. It is shown that there usually exist two simple waves and two shock wares. Finally, two examples are given for the case of plane strain deformation and antiplane strain deformation, respectively. It is proved that, in the case of plane strain deformation, the oblique reflection problem of a plane shock is not solvable in general.

Nonlinearity analysis of piezoelectric micromachined ultrasonic transducers based on couple stress theory

This paper studies the static deformation behavior of a piezoelectric micromachined ultrasonic transducer （PMUT） actuated by a strong external electric field. The transducer membrane consists of a piezoelectric layer, a passive layer and two electrode layers. The nonlinearities of the piezoelectric layer caused by electrostriction under a strong electric field are analyzed. Because the thickness of the transducer membrane is on the microscale, the size dependence of the deformation behavior is evaluated using the couple stress theory. The results show that the optimal ratio of the top electrode diameter and the membrane diameter is around 0.674. It is also found that this optimal value does not depend on any other parameters if the thicknesses of the two electrodes are negligible compared with those of the piezo- electric and passive layers. In addition, the nonlinearities of the piezoelectric layer will become stronger along with the increase of the electric field, which means that softening of the membrane stiffness occurs when a strong external electric field is applied. Meanwhile, the optimal thickness ratio for the passive layer and the piezoelectric layer is not equal to 1.0 which is usually adopted by previous researchers. Because there exists size dependence of membrane deforma-tion, the optimal value of this thickness ratio needs to be greater than 1.0 on the microscale.

STRAIN-GRADIENT STRESS ANALYSIS IN SAINT-VENANT BENDING

Light beam deflections caused by stress or strain gradients are inves- tigated analytically and experimentally in homogeneous beam specimens which are subjected to a particular case of flexure with shear. This study is a generalization of the prior an alytical-experimental examination of strain-gradient light deflections produced in stressed plates, which had concentrated on the simplest case where in- formation of interest is collected along a line of symmetry of the stress field. Main purpose of the present investigation is to document the efficacy of the strain-gradient method in analysis of the general case of stress state. The most interesting stress state is that in a beam subjected to the Saint-Venant bending, where the transversal and the longitudinal axes of the beam are in pure shear. The obtained results are compared with the predictions of the developed analytical models and with the pre- dictions of Filon's stress function. The procedures of evaluating the photoelastic and material coefficients using strain-gradient techniques were tested positively.

THREE-DIMENSIONAL ISODYNE STRESS ANALYSIS——PRESENT STATE, TRENDS, THEORETICAL PROBLEMS

The paper presents and discusses theoretical bases and methodology of development of two- and three-dimensional analytical and optical isodynes. Atten- tion is given to the theoretical admissibility of the major components of the physical and mathematical models which are taken as the theoretical basis of the isodynes, and of the related analytical and experimental procedures of stress analysis. Efficiency and reliability of the nondestructive isodyne stress analysis are discussed.

Stress analysis of clamped-free grid composite cylindrical shell under various end loadings

Stress analysis of cylindrical grid-stiffened composite shells was conducted under transverse loading,pure bending,torsion and axial compression under clamped-free boundary condition.Electrical strain gauges were employed to measure the strains in transverse loading case to validate the finite element analysis which was conducted using ANSYS software.Good agreement was obtained between the two methods.It was observed that stiffening the composite shell with helical ribs decreased the average equivalent Von Mises stress on the shell.The reduction of the stress seemed to be higher in the intersection of two ribs.It was also seen that the stress reduction ratio was higher when the structure was under bending compared to torsion and axial compression.The reduction ratio was approximately 75% in pure bending in the intersection point of the ribs,while it was approximately 25% in torsion.Therefore,it is concluded that the presence of the ribs is more effective under bending.Failure analysis was done using Tsai-Wu criterion.The ribs were observed to result in maximum and minimum increase in the failure load of the structure under transverse bending and torsional loading,respectively.

General displacement arch-cantilever element method for stress analysis of arch dam

Based on the general displacement method and the basic hypothesis of the trial load method, a new advanced trial load method, the general displacement arch-cantilever element method, was proposed to derive the transformation relation of displacements and loads between the surface nodes and middle plane nodes. This method considers the nodes on upstream and downstream surfaces of the arch dam to be exit nodes （master nodes）, and the middle plane nodes to be slave nodes. According to the derived displacement and load transformation matrices, the equilibrium equation treating the displacement of middle plane nodes as a basic unknown variable is transformed into one that treats the displacement of upstream and downstream nodes as a basic unknown variable. Because the surface nodes have only three degrees of freedom （DOF）, this method can be directly coupled with the finite element method （FEM）, which is used for foundation simulation to analyze the stress of the arch dam with consideration of dam-foundation interaction. Moreover, using the FEM, the nodal load of the arch dam can be easily obtained. Case studies of a typical cylindrical arch dam and the Wudongde arch dam demonstrate the robustness and feasibility of the proposed method.

A Novel Deep Learning Based Healthcare Model for COVID-19 Pandemic Stress Analysis

Coronavirus(COVID-19)has impacted nearly every person across the globe either in terms of losses of life or as of lockdown.The current coronavirus(COVID-19)pandemic is a rare/special situation where people can express their feelings on Internet-based social networks.Social media is emerging as the biggest platform in recent years where people spend most of their time expressing themselves and their emotions.This research is based on gathering data from Twitter and analyzing the behavior of the people during the COVID-19 lockdown.The research is based on the logic expressed by people in this perspective and emotions for the suffering of COVID-19 and lockdown.In this research,we have used a Long Short-Term Memory(LSTM)network model with Convolutional Neural Network using Keras python deep-learning library to determine whether social media platform users are depressed in terms of positive,negative,or neutral emotional out bust based on their Twitter posts.The results showed that the model has 88.14%accuracy(representation of the correct prediction over the test dataset)after 10 epochs which most tweets showed had neutral polarity.The evaluation shows interesting results in positive(1),negative(–1),and neutral(0)emotions through different visualization.

Stress Analysis of Printed Circuit Board with Different Thickness and Composite Materials Under Shock Loading

In this study,the deformation and stress distribution of printed circuit board(PCB)with different thickness and composite materials under a shock loading were analyzed by the finite element analysis.The standard 8-layer PCB subjected to a shock loading 1500 g was evaluated first.Moreover,the finite element models of the PCB with different thickness by stacking various number of layers were discussed.In addition to changing thickness,the core material of PCB was replaced from woven E-glass/epoxy to woven carbon fiber/epoxy for structural enhancement.The non-linear material property of copper foil was considered in the analysis.The results indicated that a thicker PCB has lower stress in the copper foil in PCBs under the shock loading.The stress difference between the thicker PCB(2.6 mm)and thinner PCB(0.6 mm)is around 5%.Using woven carbon fiber/epoxy as core material could lower the stress of copper foil around 6.6%under the shock loading 1500 g for the PCB with 0.6 mm thickness.On the other hand,the stress level is under the failure strength of PCBs with carbon fiber/epoxy core layers and thickness 2.6 mm when the peak acceleration changes from 1500 g to 5000 g.This study could provide a reference for the design and proper applications of the PCB with different thickness and composite materials.

Stress analysis of three-dimensional finite element model of malunion calcaneus during gait

Objective: To analyze the stress distribution of calcaneus with posterior articular facet compressed after fracture and talus during gait. Methods: A wedge under the posterior articular was transected from a normal finite element model of calcaneus and talus to simulate malformation of compression of the posterior facet after fracture of calcaneus. The model was used to simulate for three subphases of the stance during the gait(heel strike, midstance, push off) and calculate the finite element. The results were compared with normal situation. Results: The stress distribution within the bone in situation of malformation was obtained and regions of elevated stresses for three subphases were located. The results were significantly different from that of normal situation. Conclusion: The simulation of calcaneus and talus in malformation has important clinic implication and can provide an insight into the factors contributing to many clinic pathogenic changes after fracture of calcaneus.

Vibration Response and Stress Analysis of Planar Elastic Tube Bundle Induced by Fluid Flow

Flow?induced vibration plays a positive role on heat transfer enhancement. Meanwhile, it is also a negative factor for fatigue strength. Satisfying the fatigue strength is the primary prerequisite for heat transfer enhancement. This paper numerically studied the flow?induced vibration of planar elastic tube bundle based on a two?way fluid–structure interaction(FSI) calculation. The numerical calculation involved the unsteady, three?dimensional incompressible governing equations solved with finite volume approach and the dynamic balance equation of planar elastic tube bundle solved with finite element method combined with dynamic mesh scheme. The numerical approach was verified by comparing with the published experimental results. Then the vibration trajectory, deformation and stress contour of planar elastic tube bundle were all studied. Results show that the combined movement of planar elastic tube bundle represents the agitation from inside to outside. The vibration of out?of?plane is the main vibration form with the typically sinusoidal behavior because the magnitude of displacement along the out?of?plane direction is the 100 times than the value of in?plane direction. The dangerous point locates in the innermost tube where the equivalent stress can be utilized to study the multiaxial fatigue of planar elastic tube bundle due to the alternating stress concentration. In the velocity range of 0.2-3 m/s, it is inferred that the vibration amplitude plays a role on the stress response and the stress amplitude is susceptible to the fluid velocity. This research paves a way for studying the fatigue strength of planar elastic tube bundle by flow?induced vibration.