Status and Prospect of Remanufacturing Technology for Tubing and Sucker Rods

As the main consumables, huge amount of tubing and sucker rods are abandoned annually. The current remediation technology could only enable part of abandoned tubing and sucker rod to be reused in a degraded way, leading to a big resource waste. The production, use and remediation methods of tubing and sucker rod are analyzed here. Remanufacturing technology of abandoned tubing based on self-propagating high temperature synthesis(SHS) is proposed. Economic, environmental and social benefits of large scale application of this technology are evaluated. And then various factors that restrict the popularization of remanufacturing technology in the petroleum industry are studied and suggestions are given in the end. The results indicate that unlike conventional remediation methods, remanufacturing technology can extend the service life of abandoned tubing to reach or even exceed that of a new one. Meanwhile it can also reduce the cost effectively, and achieve significant economic and social benefits. We should expand remanufacturing technology areas in the petroleum industry and achieve stable, healthy development in the low oil price situation. The scientific standards for remanufactured products should be enacted, and new management mode of the remanufactured products should be developed.

Mechanical characteristic and failure mechanism of joint with composite sucker rod

Composite sucker rods are widely used in oil fields because of light weight,high strength,and corrosion resistance.Bonded technology becomes the primary connection method of composites.However,the joints with composite sucker rods are prone to debone and fracture.The connected characteristics are less considered,so the failure mechanism of the joint is still unclear.Based on the cohesive zone model(CZM)and the Johnson-Cook constitutive model,a novel full-scale numerical model of the joint with composite sucker rod was established,and verified by pull-out experiments.The mechanical properties and slip characteristics of the joint were studied,and the damaged procession of the joint was explored.The results showed that:a)the numerical model was in good agreement with the experimental results,and the error is within 5%;b)the von Mises stress,shear stress,and interface stress distributed symmetrically along the circumferential path increased gradually from the fixed end to the loading end;c)the first-bonded interface near the loading end was damaged at first,followed by debonding of the second-bonded interface,leading to the complete shear fracture of the epoxy,and resulted in the debonding of the joint with composite sucker rod,which can provide a theoretical basis for the structural design and optimization of the joint.

Using the curve moment and the PSO-SVM method to diagnose downhole conditions of a sucker rod pumping unit

Downhole working conditions of sucker rod pumping wells are automatically identified on a computer from the analysis of dynamometer cards. In this process, extraction of feature parameters and pattern classification are two key steps. The dynamometer card is firstly divided into four parts which include different production information according to the ＂four point method＂ used in actual oilfield production, and then the moment invariants for pattern recognition are extracted. An improved support vector machine （SVM） method is used for pattern classification whose error penalty parameter C and kernel function parameter g are optimally chosen by the particle swarm optimization （PSO） algorithm. The simulation results show the method proposed in this paper has good classification results.

Fault diagnosis for down-hole conditions of sucker rod pumping systems based on the FBH-SC method

Dynamometer cards are commonly used to analyze down-hole working conditions of pumping systems in actual oil production. Nowadays, the traditional supervised learning methods heavily rely on the classification accuracy of the training samples. In order to reduce the errors of manual classification, an automatic clustering algorithm is proposed and applied to diagnose down-hole conditions of pumping systems. The spectral clustering （SC） is a new clustering algorithm, which is suitable for any data distribution. However, it is sensitive to initial cluster centers and scale parameters, and needs to predefine the cluster number. In order to overcome these shortcom- ings, we propose an automatic clustering algorithm, fast black hole-spectral clustering （FBH-SC）. The FBH algo- rithm is used to replace the K-mean method in SC, and a CritC index function is used as the target function to automatically choose the best scale parameter and clus- tering number in the clustering process. Different simulation experiments were designed to define the relationship among scale parameter, clustering number, CritC index value, and clustering accuracy. Finally, an example is given to validate the effectiveness of the proposed algorithm.

Approach to the Design Calculation of Sucker Rod Pumping Systems in Coalbed Methane Wells

The existing design of the pumping systems mainly focuses on the approximate computational formulae and procedures,which are developed based on the analytic approaches of conventional oil/gas fields.The calculation of polished rod loads usually just concerns about the static and inertial loads.And the computation of gearbox torque generally uses empirical formulae and correction factors.The above modeling procedures,if applied to the coalbed methane（CBM） wells,can not give the desired accuracy of the system design and its pertinent analysis.In this paper,based on the kinematic and dynamic analysis of the pumping system,the kinematic relation of polished rod is analyzed,and the variation of the total loads of polished rod is developed with the limits of CBM well conditions along the string.The gearbox torque calculation model is established by combining the counterbalance effect with the calculated dynamometer cards and torque factors.The application characteristics of this model are demonstrated by the example of ZH002-4 well in Qinshui basin.The interpretations of results show that the cranks of beam units should rotate in a counter clockwise direction viewed with the wellhead to the right.Compared with oil？gas fields,the dynamic and friction to polished rod load ratios are relatively high and the computation of polished rod loads should involve the static and inertial loads,as well as vibration and friction loads.And the dynamic load ratio decreases rapidly during the production.Besides,the total deformation of the string is small in CBM wells.As for balanced operation,the gearbox torque load usually has two approximately equal peaks and the magnitudes of instantaneous torque are just within 50% of unbalanced gearbox loadings.The proposed research improves efficiency of the pumping system,loads the pumping unit more uniformly,and provides the reasonable basis for selecting the units.

Adaptive fault diagnosis of sucker rod pump systems based on optimal perceptron and simulation data

A highly precise and timely diagnosis technology can help effectively monitor and adjust the sucker rod production system(SRPS)used in oil wells to ensure a safe and efficient production.The current diagnosis method is pattern recognition of a dynamometer card(DC)based on feature extraction and perceptron.The premise of this method is that the training and target data have the same distribution.However,the training data are collected from a field SRPS with different system parameters designed to adapt to production conditions,which may significantly affect the diagnostic accuracy.To address this issue,in this study,an improved model of the sucker rod string(SRS)is derived by adding faultparameter dimensions,with which DCs under 16 working conditions could be generated.Subsequently an adaptive diagnosis method is proposed by taking simulated DCs generated near the working point of the target SRPS as training data.Meanwhile,to further improve the accuracy of the proposed method,the DC features are improved by relative normalization and using additional features of the DC position to increase the distance between different types of samples.The parameters of the perceptron are optimized to promote its discriminability.Finally,the accuracy and real-time performance of the proposed adaptive diagnosis method are validated using field data.

Effect of Produced Fluid on the Wear Behavior of Grade D Sucker Rod and N80 Type Tubing

Inuestigated wear tests of grade D sucker rod and N80 tubing with a produced liquid are the effect of the water cut of produced liquid on the wear rate and the wear coefficient of the friction pair. And presented here is a comparison of tribological performance of tubing/sucker rod with sprayed tubing/sucker rod and tubing/sprayed sucker rod. The results show that one of the main reasons for wear failure between the sucker rod and the tubing is a high water cut of the produced liquid. The wear rate increases greatly when the water cut ranges from 70% to 85%, and increases gradually when the water cut is less than 70% or more than 85%. The higher the water cut is, the greater the wear rate will be. SEM (scanning electron microscope) micrographs show that the worn surface of the tubing is smoother, with shallow grooves, when the water cut is 55%; when the water cut is 95%, there are broader and deeper grooves on the worn surface. The results also show that the wear rate of the sprayed wear-resistant coating of sucker rod/tubing is less than that of the unsprayed sucker rod/tubing.

Online Magnetic Flux Leakage Detection System for Sucker Rod Defects Based on LabVIEW Programming

Aiming at the detection of the sucker rod defects,a real-time detection system is designed using the non-destructive testing technology of magnetic flux leakage(MFL).An MFL measurement system consists of many parts,and this study focuses on the signal acquisition and processing system.First of all,this paper introduces the hardware part of the acquisition system in detail,including the selection of the Hall-effect sensor,the design of the signal conditioning circuit,and the working process of the single chip computer(SCM)control serial port.Based on LabVIEW,a graphical programming software,the software part of the acquisition system is written,including serial port parameter configuration,detection signal recognition,original signal filtering,real-time display,data storage and playback.Finally,an experimental platform for the MFL detection is set up,and the MFL measurement is carried out on the transverse and longitudinal defects of the sucker rod surface.The experimental result shows that the designed acquisition and processing system has good detection performance,simple design and high flexibility.

Novel sucker rod pumping system based on linear motor technology

Obtaining petroleum at the cost of electrical energy is a common problem in almost all oil fields, and it is mainly caused by low duty radio of induction motor used in beam pumping units. Traditional beam-pumping units have many intrinsic disadvantages such as low efficiency, complex transmission devices, poor flexibility, tremendous volume and weight in long stroke, etc.Therefore, a novel direct driven linear electromagnetic pumping unit (EMPU) has been developed by combining oil extraction technology with linear motor technology. The thrust of EMPU matches the changing of suspension center load to improve the system efficiency and cut down the consumption of energy. Based on previous experience, a small-scale prototype was developed and a simulation was conducted with it. Both theoretical analyses and experimental study showed that the problems exiting in beam pumping units can be solved with EMPU system, and this is a new method which can be used to solve high energy waste in oil fields.

Fluid characteristic of multiphase fluid in annular space between pump barrel and plunger

The pump performance parameters,such as pump pressure,plunger friction and pump valve resistance,are fundamental parameters of optimal design of pump efficiency and sucker rod pumping system (SRPS).In this paper,considering the characteristic of geometrical nonlinear and rheology property of multiphase fluid,the pump performance parameters are studied.Firstly,a dynamics model of annular fluid flow is built.In the detail,a partial differential equation of annular fluid is established and a computing model of fluid pressure gradient is built.Secondly,the simulation models of plunger friction and hydraulic resistance of pump valve are built.Finally,a novel simulation method of fluid pressure in annular space is proposed with software ANSYS.In order to check up the correction of models proposed in this paper,the comparison curves of experiment and simulation results are given.Based on above model,the whole simulation model of plunger pump is simulated with Visual Basic 6.0.The results show that the fluid friction of pump plunger and instantaneous resistance of pump valve are nonlinear.The impact factors of pump performance parameters are analyzed,and their characteristic curves are given,which can help to optimize the pump motion parameters and pump structural.

Dynamic simulation and efficiency analysis of beam pumping system

An improved whole model of beam pumping system was built. In the detail, for surface transmission system(STS), a new mathematical model was established considering the influence of some factors on the STS's torsional vibration, such as the time variation characteristic of equivalent stiffness of belt and equivalent rotational inertia of crank. For the sucker rod string(SRS), an improved mathematical model was built considering the influence of some parameters on the SRS's longitudinal vibration, such as the nonlinear friction of plunger, hydraulic loss of pump and clearance leakage. The dynamic response and system efficiency of whole system were analyzed. The results show that there is a jumping phenomenon in the amplitude frequency curve, and the system efficiency is sensitive to motor power, pump diameter, stroke number, ratio of gas and oil, and submergence depth. The simulation results have important significance for improving the efficiency of beam pumping system.

The Tribological Properties of the Hot-extrusion Nylon Coating in the Oil Well Environment

The friction and wear properties of the nylon coating,prepared by hot-extrusion, used to protect the surface of the flexible continuous sucker rod were studied by using a pin-on-disc wear tester in the simulated oil well environment.The effects of sliding speed and load were considered.The wear mechanism was also studied by using a scanning electron microscope (SEM).The result shows that the friction coefficients of both kinds of materials,JKPA and ZZ7024B,used to protect the surface of the flexible continuous sucker rod decrease with sliding speed increase,but change little with load increase in the simulated oil well environment.The value of friction coefficient of ZZ7024B is smaller than that of JKPA.The minimum value of friction coefficient of ZZ7024B is about 0.05.The wear volume of ZZ7024B is smaller than that of JKPA under the same conditions of experimentation.