The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the...The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 mm.Numerical simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow features.The results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were analyzed.In calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So heat transfer deterioration should be taken seriously in the design and safe operation of vaporizer PCHE. The study of this work clarified the local heat transfer and flow feature of supercritical methane in microchannel and contributed to the deep understanding of supercritical methane flow of the vaporization process in PCHE.展开更多
The supercritical CO_(2)(sCO_(2))power cycle could improve efficiencies for a wide range of thermal power plants.The sCO_(2)turbine generator plays an important role in the sCO_(2)power cycle by directly converting th...The supercritical CO_(2)(sCO_(2))power cycle could improve efficiencies for a wide range of thermal power plants.The sCO_(2)turbine generator plays an important role in the sCO_(2)power cycle by directly converting thermal energy into mechanical work and electric power.The operation of the generator encounters challenges,including high temperature,high pressure,high rotational speed,and other engineering problems,such as leakage.Experimental studies of sCO_(2)turbines are insufficient because of the significant difficulties in turbine manufacturing and system construction.Unlike most experimental investigations that primarily focus on 100 kW‐or MW‐scale power generation systems,we consider,for the first time,a small‐scale power generator using sCO_(2).A partial admission axial turbine was designed and manufactured with a rated rotational speed of 40,000 rpm,and a CO_(2)transcritical power cycle test loop was constructed to validate the performance of our manufactured generator.A resistant gas was proposed in the constructed turbine expander to solve the leakage issue.Both dynamic and steady performances were investigated.The results indicated that a peak electric power of 11.55 kW was achieved at 29,369 rpm.The maximum total efficiency of the turbo‐generator was 58.98%,which was affected by both the turbine rotational speed and pressure ratio,according to the proposed performance map.展开更多
The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayto...The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayton cycle layouts are developed in this study for different reactors to reduce the cost and increase the thermohydraulic performance of nuclear power generation to promote the commercialization of nuclear energy.Parametric analysis,multi-objective optimizations,and four decision-making methods are applied to obtain each Brayton scheme’s optimal thermohydraulic and economic indexes.Results show that for the same design thermal power scale of reactors,the higher the core’s exit temperature,the better the Brayton cycle’s thermo-economic performance.Among the four-cycle layouts,the recompression cycle(RC)has the best overall performance,followed by the simple recuperation cycle(SR)and the intercooling cycle(IC),and the worst is the reheating cycle(RH).However,RH has the lowest total cost of investment(C_(tot))of$1619.85 million,and IC has the lowest levelized cost of energy(LCOE)of 0.012$/(kWh).The nuclear Brayton cycle system’s overall performance has been improved due to optimization.The performance of the molten salt reactor combined with the intercooling cycle(MSR-IC)scheme has the greatest improvement,with the net output power(W_(net)),thermal efficiencyη_(t),and exergy efficiency(η_(e))improved by 8.58%,8.58%,and 11.21%,respectively.The performance of the lead-cooled fast reactor combined with the simple recuperation cycle scheme was optimized to increase C_(tot) by 27.78%.In comparison,the internal rate of return(IRR)increased by only 7.8%,which is not friendly to investors with limited funds.For the nuclear Brayton cycle,the molten salt reactor combined with the recompression cycle scheme should receive priority,and the gas-cooled fast reactor combined with the reheating cycle scheme should be considered carefully.展开更多
As a common precursor for supercritical CO_(2)(scCO_(2))deposition techniques,solubility data of organometallic complexes in scCO_(2)is crucial for the preparation of nanocomposites.Recently,metal acetylacetonates hav...As a common precursor for supercritical CO_(2)(scCO_(2))deposition techniques,solubility data of organometallic complexes in scCO_(2)is crucial for the preparation of nanocomposites.Recently,metal acetylacetonates have shown great potential for the preparation of single-atom catalytic materials.In this study,the solubilities of iron(Ⅲ)acetylacetonate(Fe(acac)3)and nickel(Ⅱ)acetylacetonate(Ni(acac)2)were measured at the temperature from 313.15 to 333.15 K and in the pressure range of 9.5–25.2 MPa to accumulate new solubility data.Solubility was measured using a static weight loss method.The semi-empirical models proposed by Chrastil and Sung et al.were used to correlate the solubility data of Fe(acac)3 and Ni(acac)2.The equations obtained can be used to predict the solubility of the same system in the experimental range.展开更多
Nuclear power plants exhibit non-linear and time-variable dynamics.Therefore,designing a control system that sets the reactor power and forces it to follow the desired load is complicated.A supercritical water reactor...Nuclear power plants exhibit non-linear and time-variable dynamics.Therefore,designing a control system that sets the reactor power and forces it to follow the desired load is complicated.A supercritical water reactor(SCWR)is a fourth-generation conceptual reactor.In an SCWR,the non-linear dynamics of the reactor require a controller capable of control-ling the nonlinearities.In this study,a pressure-tube-type SCWR was controlled during reactor power maneuvering with a higher order sliding mode,and the reactor outgoing steam temperature and pressure were controlled simultaneously.In an SCWR,the temperature,pressure,and power must be maintained at a setpoint(desired value)during power maneuvering.Reactor point kinetics equations with three groups of delayed neutrons were used in the simulation.Higher-order and classic sliding mode controllers were separately manufactured to control the plant and were compared with the PI controllers speci-fied in previous studies.The controlled parameters were reactor power,steam temperature,and pressure.Notably,for these parameters,the PI controller had certain instabilities in the presence of disturbances.The classic sliding mode controller had a higher accuracy and stability;however its main drawback was the chattering phenomenon.HOSMC was highly accurate and stable and had a small computational cost.In reality,it followed the desired values without oscillations and chattering.展开更多
Perilla frutescens seed (PFS) oil is reported to inhibit skin photoaging;however, its effect on melanogenesis has not yet been investigated. Herein, we tested the anti-melanogenesis activity of an oil-based extract fr...Perilla frutescens seed (PFS) oil is reported to inhibit skin photoaging;however, its effect on melanogenesis has not yet been investigated. Herein, we tested the anti-melanogenesis activity of an oil-based extract from PFS with supercritical carbon dioxide (scCO<sub>2</sub>). In a cell culture system, B16 mouse melanoma cells were treated with the PFS scCO<sub>2</sub> extract and other samples. The PFS scCO<sub>2</sub> extract decreased melanin production by approximately 90% in B16 mouse melanoma cells without cytotoxicity at 100 μg/mL. This effect was greater than that of the well-known melanogenesis inhibitor, kojic acid. Although a hexane-extracted PFS oil and a squeezed PFS oil also decreased melanin production in the B16 cells, the inhibitory effect of the PFS scCO<sub>2</sub> extract was higher than both of these. Chemical analysis of the PFS scCO<sub>2</sub> extract and squeezed PFS oil showed that almost 90% of the components of both oils were α-linolenic acid, linoleic acid, and oleic acid. Furthermore, the ratio of those three fatty acids across both samples was almost the same. When the three fatty acids were mixed in the same ratio as in the PFS scCO<sub>2</sub> extract, the IC<sub>50</sub> of the mixture for melanin production in B16 melanoma cells was identical to that of the PFS scCO<sub>2</sub> extract. However, the IC<sub>50</sub> of the squeezed PFS oil was approximately 6.6 times higher than that of the mixture. Although those fatty acids are the main inhibitory ingredients against melanin production in all of the extracts, some factor(s) in the squeezed PFS reduce their affinity with the cells. These results indicated that the PFS scCO<sub>2</sub> extract could be a superior melanogenesis inhibitor. Although its main ingredients are probably the same as those of the squeezed PFS oil, it is necessary to extract with scCO<sub>2</sub> for stronger anti-melanogenesis activity.展开更多
Since the mechanisms of methane-mudstone interactions are important for estimating shale gas reserves,methane adsorption under supercritical conditions of 30 MPa pressure and 303.15,333.15,363.15 K temperatures was st...Since the mechanisms of methane-mudstone interactions are important for estimating shale gas reserves,methane adsorption under supercritical conditions of 30 MPa pressure and 303.15,333.15,363.15 K temperatures was studied to measure the excess methane adsorption in two mudstone samples from Yanchang Formation,Ordos Basin.Excess adsorption features inflection points where the amount of adsorbed gas changes from increasing to decreasing concentrations.Three methods(fixed,slope,and freely fitted density)were applied to calculate the adsorbed-phase density(rad),which was then used to fit the measured excess adsorption.Two criteria,the goodness-of-fit and whether the fitting can obtain reasonable absolute adsorption,were applied to determine the most accurate model.Results indicated that the supercritical Dubinin-Radushkevich(SDR)model with freely fitted rad was the most reasonable model.The volume of adsorbed methane at 363.15 K is close to the micropore(d<2 nm)volume of the corresponding mudstone.Considering the actual geological conditions,the adsorbed gas should be predominantly stored in micropores.Thermodynamic parameters reveal that the methane adsorption on mudstone is a physisorption process that is jointly controlled by the heterogeneity of,and interaction forces between the methane molecule and,the rock surface.展开更多
Supercritical carbon dioxide(ScCO_(2))fracturing has great advantages and prospects in both shale gas exploitation and CO_(2)storage.This paper reviews current laboratory experimental methods and results for sedimenta...Supercritical carbon dioxide(ScCO_(2))fracturing has great advantages and prospects in both shale gas exploitation and CO_(2)storage.This paper reviews current laboratory experimental methods and results for sedimentary rocks fractured by ScCO_(2).The breakdown pressure,fracture parameters,mineral composition,bedding plane angle and permeability are discussed.We also compare the differences between sedimentary rock and granite fractured by ScCO_(2),ultimately noting problems and suggesting solutions and strategies for the future.The analysis found that the breakdown pressure of ScCO_(2)was reduced 6.52%–52.31%compared with that of using water.ScCO_(2)tends to produce a complex fracture morphology with significantly higher permeability.When compared with water,the fracture aperture of ScCO_(2)was decreased by 4.10%–72.33%,the tortuosity of ScCO_(2)was increased by 5.41%–70.98%and the fractal dimension of ScCO_(2)was increased by 4.55%–8.41%.The breakdown pressure of sandstone is more sensitive to the nature of the fracturing fluid,but fracture aperture is less sensitive to fracturing fluid than for shale and coal.Compared with granite,the tortuosity of sedimentary rock is more sensitive to the fracturing fluid and the fracture fractal dimension is less sensitive to the fracturing fluid.Existing research shows that ScCO_(2)has the advantages of low breakdown pressure,good fracture creation and environmental protection.It is recommended that research be conducted in terms of sample terms,experimental conditions,effectiveness evaluation and theoretical derivation in order to promote the application of ScCO_(2)reformed reservoirs in the future.展开更多
As an emerging waterless fracturing technology,supercritical carbon dioxide(SC-CO_(2))fracturing can reduce reservoir damage and dependence on water resources,and can also promote the reservoir stimulation and geologi...As an emerging waterless fracturing technology,supercritical carbon dioxide(SC-CO_(2))fracturing can reduce reservoir damage and dependence on water resources,and can also promote the reservoir stimulation and geological storage of carbon dioxide(CO_(2)).It is vital to figure out the laws in SC-CO_(2)fracturing for the large-scale field implementation of this technology.This paper reviews the numerical simulations of wellbore flow and heat transfer,fracture initiation and propagation,and proppant transport in SC-CO_(2)fracturing,including the numerical approaches and the obtained findings.It shows that the variations of wellbore temperature and pressure are complex and strongly transient.The wellhead pressure can be reduced by tubing and annulus co-injection or adding drag reducers into the fracturing fluid.Increasing the temperature of CO_(2)with wellhead heating can promote CO_(2)to reach the well bottom in the supercritical state.Compared with hydraulic fracturing,SC-CO_(2)fracturing has a lower fracture initiation pressure and can form a more complex fracture network,but the fracture width is narrower.The technology of SC-CO_(2)fracturing followed by thickened SC-CO_(2)fracturing,which combines with high injection rates and ultra-light proppants,can improve the placement effect of proppants while improving the complexity and width of fractures.The follow-up research is required to get a deeper insight into the SC-CO_(2)fracturing mechanisms and develop cost-effective drag reducers,thickeners,and ultra-light proppants.This paper can guide further research and promote the field application of SC-CO_(2)fracturing technology.展开更多
The flow and heat transfer characteristics of n-decane in the sub-millimeter spiral tube(SMST) at supercritical pressure(p = 3 MPa) are studied by the RNG k-ε numerical model in this paper. The effects of various Rey...The flow and heat transfer characteristics of n-decane in the sub-millimeter spiral tube(SMST) at supercritical pressure(p = 3 MPa) are studied by the RNG k-ε numerical model in this paper. The effects of various Reynolds numbers(Re) and structural parameters pitch(s) and spiral diameter(D) are analyzed.Results indicate that the average Nusselt numberNu and friction factorNu increase with an increase in Re, and decrease with an increase in D/d(tube diameter). In terms of the structural parameter s/d, it is found that as s/d increases, the Nu first increase, and then decrease. and the critical structural parameter is s/d = 4. Compared with the straight tube, the SMST can improve Nu by 34.8% at best, while it can improve Nu by 102.1% at most. In addition, a comprehensive heat transfer coefficient is applied to analyze the thermodynamic properties of SMST. With the optimal structural parameters of D/d = 6 and s/d = 4, the comprehensive heat transfer factor of supercritical pressure hydrocarbon fuel in the SMST can reach 1.074. At last, correlations of the average Nusselt number and friction factor are developed to predict the flow and heat transfer of n-decane at supercritical pressure.展开更多
To investigate the impacts of water/supercritical CO_(2)-rock interaction on the micro-mechanical properties of shale,a series of high-temperature and high-pressure immersion experiments were performed on the calcareo...To investigate the impacts of water/supercritical CO_(2)-rock interaction on the micro-mechanical properties of shale,a series of high-temperature and high-pressure immersion experiments were performed on the calcareous laminated shale samples mined from the lower submember of the third member of Paleogene Shahejie Formation in the Jiyang Depression,Bohai Bay Basin.After that,grid nanoindentation tests were conducted to analyze the influence of immersion time,pressure,and temperature on micro-mechanical parameters.Experimental results show that the damage of shale caused by the water/supercritical CO_(2)-rock interaction was mainly featured by the generation of induced fractures in the clay-rich laminae.In the case of soaking with supercritical CO_(2),the aperture of induced fracture was smaller.Due to the existence of induced fractures,the statistical averages of elastic modulus and hardness both decreased.Meanwhile,compaction and stress-induced tensile fractures could be observed around the laminae.Generally,the longer the soaking time,the higher the soaking pressure and temperature,the more significant the degradation of micro-mechanical parameters is.Compared with water-rock interaction,the supercritical CO_(2)-rock interaction caused a lower degree of mechanical damage on the shale surface.Thus,supercritical CO_(2)can be used as a fracturing fluid to prevent the surface softening of induced fractures in shale reservoirs.展开更多
[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface method...[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface methodology. [Results] The optimum extraction conditions of black tea extract by supercritical CO_(2) extraction were as follows: extraction pressure 23.53 MPa, extraction time 1.73 h, and extraction temperature 49.75 ℃, with which the extract yield could reach 5.15% theoretically. [Conclusions] Based on the traditional extraction process, a supercritical extraction method optimized by response surface methodology and a unique extraction process were formed, which enriches the extraction processes and methods of natural raw materials.展开更多
In this paper, a system of Lorenz-type ordinary differential equations is considered and, under some assumptions about the parameter space, the presence of the supercritical non-degenerate Hopf bifurcation is demonstr...In this paper, a system of Lorenz-type ordinary differential equations is considered and, under some assumptions about the parameter space, the presence of the supercritical non-degenerate Hopf bifurcation is demonstrated. The technical tool used consists of the Central Manifold theorem, a well-known formula to calculate the Lyapunov coefficient and Hopf’s Theorem. For particular values of the parameters in the parameter space established in the main result of this work, a graph is presented that describes the evolution of the trajectories, obtained by means of numerical simulation.展开更多
An efficient and environment-friendly method for simultaneous determination of 13 typical derivatives of polycyclic aromatic hydrocarbon(PAH)in petroleum-polluted soil with nitro-,oxy-and alkylfunctional group was dev...An efficient and environment-friendly method for simultaneous determination of 13 typical derivatives of polycyclic aromatic hydrocarbon(PAH)in petroleum-polluted soil with nitro-,oxy-and alkylfunctional group was developed using supercritical fluid extraction(SFE)followed by ultra-high performance supercritical fluid chromatography(UHPSFC).Parameters of UHPSFC,including type of stationary phase and mobile phase modifiers,gradient elution process,backpressure,column temperature,and the flow rate of mobile phase,were systematically optimized,achieving a fast separation within4.2 min.Limits of detection(LOD)were 0.005-0.1μg mL^(-1)or 0.1-2.0 ng g^(-1),respectively,with a good repeatability(RSD<5.0%).Before UHPSFC-PDA analysis,the PAH-derivatives in soil samples were effectively enriched in 15.0 min using SFE with an online carbon nanotubes(CNTs)collection trap.The soil samples were analyzed by the proposed method and the results were verified by GC-MS.Thus,SFE equipped with an online CNTs trap followed by UHPSFC-PDA analysis,which only consumed about2.0 mL organic solvent for a whole run,has been demonstrated to be an efficient way for screening and quantitative analysis of trace-level PAH-derivatives in soil samples.展开更多
A series of nanosized Co/Zn/Mn/K composite catalysts for Fischer-Tropsch synthesis (FTS) were prepared by supercritical fluid drying (SCFD) method and common drying (CD) method. The nanosized cobalt-based cataly...A series of nanosized Co/Zn/Mn/K composite catalysts for Fischer-Tropsch synthesis (FTS) were prepared by supercritical fluid drying (SCFD) method and common drying (CD) method. The nanosized cobalt-based catalysts were characterized by XRD, TEM and BET techniques. Their catalytic performances were tested in a slurry-bed reactor under FTS reaction conditions. The drying and crystallization were carried out simultaneously during SCFD, therefore, the catalysts prepared by SCFD method have ideal structure and show the FTS performance superior to the others prepared by CD method. The FTS activity and selectivity were improved via adding Zn, Mn and K promoters, and less CH4 and CO2 as well as higher yield of C5+ products were achieved. The optimal performance of a 92% CO conversion and a 65% C5+ product yield was obtained over a catalyst with the component of Co/Zn/Mn/K = 100/50/10/7. Furthermore, the catalytic performance was studied under the conditions of liquid-phase and supercritical phase slurry-bed, and C5+ product yield were 57.4% and 65.4%, respectively. In summary, better catalytic performance was obtained using the nanosized catalyst prepared by SCFD method under supercritical reaction conditions, resulting in higher conversion of CO, less CO2 byproduct, and higher yield of C5+ products.展开更多
In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC ...In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC is not yet applied for drug quality control in the daily routine framework. Among the numerous reported SFC methods, none of them could be found to fully satisfy to all steps of the analytical method lifecycle. Thereby, the present contribution aims to provide an overview of the current and past achievements related to SFC techniques, with a targeted attention to this lifecycle and its successive steps. The included discussions were therefore structured accordingly and emphasizing the analytical method lifecycle in accord with the International Conference on Harmonisation (ICH). Recent and important scientific outputs in the field of analytical SFC, as well as instrumental evolution, qualification strategies, method development methodologies and discussions on the topic of method validation are reviewed.展开更多
It is well known that seawater that migrates deep into the Earth’s crust will pass into its supercritical domain at temperatures above 407°C and pressures above 298 bars. In the oceanic crust, these pressures ar...It is well known that seawater that migrates deep into the Earth’s crust will pass into its supercritical domain at temperatures above 407°C and pressures above 298 bars. In the oceanic crust, these pressures are attained at depths of 3 km below sea surface, and sufficiently high temperatures are found near intruding magmas, which have temperatures in the range of 800°C to 1200°C. The physico-chemical behaviour of seawater changes dramatically when passing into the supercritical domain. A supercritical water vapour (ScriW) is formed with a density of 0.3 g/cc and a strongly reduced dipolar character. This change in polarity is causing the ScriW to lose its solubility of the common sea salts (chlorides and sulphates) and a spontaneous precipitation of sea salts takes place in the pore system. However, this is only one of many cases where the very special properties of ScriW affect its surroundings. The objective of this paper is to increase awareness of the many geological processes that are initiated and governed by ScriW. This includes interactions between ScriW and its geological surroundings to initiate and drive processes that are of major importance to the dynamics and livelihood of our planet. ScriW is the driver of volcanism associated with subduction zones, as ScriW deriving from the subduction slab is interacting with the mantle rocks and reducing their melting point. ScriW is also initiating serpentinization processes where olivines in the mantle rocks (e.g. peridotite) are transformed to serpentine minerals upon the uptake of OH-groups from hydrolysed water. The simultaneous oxidation of Fe2+ dissolved from iron-bearing pyroxenes and olivines leads to the formation of magnetite and hydrogen, and consequently, to a very reducing environment. ScriW may also be the potential starter and driver of the poorly understood mud and asphalt volcanism;both submarine and terrestrial. Furthermore, the lack of polarity of the water molecules in ScriW gives the ScriW vapour the potential to dissolve organic matter and petroleum. The same applies to supercritical brines confined in subduction slabs. If these supercritical water vapours migrate upwards to reach the critical point, the supercritical vapour is condensed into steam and dissolved petroleum is partitioned from the water phase to become a separate fluid phase. This opens up the possibility of transporting petroleum long distances when mixed with ScriW. Therefore, we may, popularly, say that ScriW drives a gigantic underground refinery system and also a salt factory. It is suggested that the result of these processes is that ScriW is rejuvenating the world’s ocean waters, as all of the ocean water circulates into the porous oceanic crust and out again in cycles of less than a million years. In summary, we suggest that ScriW participates in and is partly responsible for: 1) Ocean water rejuvenation and formation;2) Fundamental geological processes, such as volcanism, earthquakes, and meta-morphism (including serpentinization);3) Solid salt production, accumulation, transportation, and (salt) dome formation;4) The initiation and driving of mud, serpentine, and asphalt volcanoes;5) Dissolution of organic matter and petroleum, including transportation and phase separation (fractionation), when passing into the subcritical domain of (liquid) water.展开更多
In this paper, we show that supercritical fluids have a greater significance in the generation of pegmatites,and for ore-forming processes related to granites than is usually assumed. We show that the supercritical me...In this paper, we show that supercritical fluids have a greater significance in the generation of pegmatites,and for ore-forming processes related to granites than is usually assumed. We show that the supercritical melt or fluid is a silicate phase in which volatiles; principally H_2O are completely miscible in all proportions at magmatic temperatures and pressures. This phase evolves from felsic melts and changes into hydrothermal fluids, and its unique properties are particularly important in sequestering and concentrating low abundance elements, such as metals. In our past research, we have focused on processes observed at upper crustal levels, however extensive work by us and other researchers have demonstrated that supercritical melt/fluids should be abundant in melting zones at deep-crustal levels too. We propose that these fluids may provide a connecting link between lower and upper crustal magmas,and a highly efficient transport mechanism for usually melt incompatible elements. In this paper, we explore the unique features of this fluid which allow the partitioning of variouselements and compounds, potentially up to extreme levels,and may explain various features both of mineralization and the magmas that produced them.展开更多
Environmentally benign carbon dioxide offers significant potential in its supercritical fluid phase to replace current reliance on a range of hazardous, relatively expensive and environmentally damaging organic solven...Environmentally benign carbon dioxide offers significant potential in its supercritical fluid phase to replace current reliance on a range of hazardous, relatively expensive and environmentally damaging organic solvents that are used on an extensive global basis. The unique combination of the physical properties of supercritical fluids are being exploited and further researched to continue the development and establishment of high efficiency, compact plant to provide energy and water efficient manufacturing processes. This mini-review is focused on the use and potential applications of supercritical fluid carbon dioxide for a selected range of key and emerging industrial processes as a sustainable alternative to totally eliminate or greatly reduce the requirement of numerous conventional organic solvents. Examples of the industries include: chemical extraction and purification, synthetic chemical reactions including polymerization and inorganic catalytic processes. Biochemical reactions involving enzymes, particle size engineering, textile dyeing and advanced material manufacture provide further illustrations of vital industrial activities where supercritical fluid technology processes are being implemented or developed. Some aspects relating to the economics of sustainable supercritical fluid carbon dioxide processes are also considered.展开更多
基金provided by Science and Technology Development Project of Jilin Province(No.20230101338JC)。
文摘The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 mm.Numerical simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow features.The results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were analyzed.In calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So heat transfer deterioration should be taken seriously in the design and safe operation of vaporizer PCHE. The study of this work clarified the local heat transfer and flow feature of supercritical methane in microchannel and contributed to the deep understanding of supercritical methane flow of the vaporization process in PCHE.
基金National Science Fund for Excellent Young Scholars,Grant/Award Number:52022066。
文摘The supercritical CO_(2)(sCO_(2))power cycle could improve efficiencies for a wide range of thermal power plants.The sCO_(2)turbine generator plays an important role in the sCO_(2)power cycle by directly converting thermal energy into mechanical work and electric power.The operation of the generator encounters challenges,including high temperature,high pressure,high rotational speed,and other engineering problems,such as leakage.Experimental studies of sCO_(2)turbines are insufficient because of the significant difficulties in turbine manufacturing and system construction.Unlike most experimental investigations that primarily focus on 100 kW‐or MW‐scale power generation systems,we consider,for the first time,a small‐scale power generator using sCO_(2).A partial admission axial turbine was designed and manufactured with a rated rotational speed of 40,000 rpm,and a CO_(2)transcritical power cycle test loop was constructed to validate the performance of our manufactured generator.A resistant gas was proposed in the constructed turbine expander to solve the leakage issue.Both dynamic and steady performances were investigated.The results indicated that a peak electric power of 11.55 kW was achieved at 29,369 rpm.The maximum total efficiency of the turbo‐generator was 58.98%,which was affected by both the turbine rotational speed and pressure ratio,according to the proposed performance map.
基金This work was supported of National Natural Science Foundation of China Fund(No.52306033)State Key Laboratory of Engines Fund(No.SKLE-K2022-07)the Jiangxi Provincial Postgraduate Innovation Special Fund(No.YC2022-s513).
文摘The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayton cycle layouts are developed in this study for different reactors to reduce the cost and increase the thermohydraulic performance of nuclear power generation to promote the commercialization of nuclear energy.Parametric analysis,multi-objective optimizations,and four decision-making methods are applied to obtain each Brayton scheme’s optimal thermohydraulic and economic indexes.Results show that for the same design thermal power scale of reactors,the higher the core’s exit temperature,the better the Brayton cycle’s thermo-economic performance.Among the four-cycle layouts,the recompression cycle(RC)has the best overall performance,followed by the simple recuperation cycle(SR)and the intercooling cycle(IC),and the worst is the reheating cycle(RH).However,RH has the lowest total cost of investment(C_(tot))of$1619.85 million,and IC has the lowest levelized cost of energy(LCOE)of 0.012$/(kWh).The nuclear Brayton cycle system’s overall performance has been improved due to optimization.The performance of the molten salt reactor combined with the intercooling cycle(MSR-IC)scheme has the greatest improvement,with the net output power(W_(net)),thermal efficiencyη_(t),and exergy efficiency(η_(e))improved by 8.58%,8.58%,and 11.21%,respectively.The performance of the lead-cooled fast reactor combined with the simple recuperation cycle scheme was optimized to increase C_(tot) by 27.78%.In comparison,the internal rate of return(IRR)increased by only 7.8%,which is not friendly to investors with limited funds.For the nuclear Brayton cycle,the molten salt reactor combined with the recompression cycle scheme should receive priority,and the gas-cooled fast reactor combined with the reheating cycle scheme should be considered carefully.
基金financial support from the National Key Research and Development Program of China(2020YFA0710202)the National Natural Science Foundation of China(21978043,U1662130)+1 种基金Inner Mongolia University of Technology Scientific Research Initial Funding(DC2300001240)Talent Introduction Support Project of Inner Mongolia(DC2300001426).
文摘As a common precursor for supercritical CO_(2)(scCO_(2))deposition techniques,solubility data of organometallic complexes in scCO_(2)is crucial for the preparation of nanocomposites.Recently,metal acetylacetonates have shown great potential for the preparation of single-atom catalytic materials.In this study,the solubilities of iron(Ⅲ)acetylacetonate(Fe(acac)3)and nickel(Ⅱ)acetylacetonate(Ni(acac)2)were measured at the temperature from 313.15 to 333.15 K and in the pressure range of 9.5–25.2 MPa to accumulate new solubility data.Solubility was measured using a static weight loss method.The semi-empirical models proposed by Chrastil and Sung et al.were used to correlate the solubility data of Fe(acac)3 and Ni(acac)2.The equations obtained can be used to predict the solubility of the same system in the experimental range.
文摘Nuclear power plants exhibit non-linear and time-variable dynamics.Therefore,designing a control system that sets the reactor power and forces it to follow the desired load is complicated.A supercritical water reactor(SCWR)is a fourth-generation conceptual reactor.In an SCWR,the non-linear dynamics of the reactor require a controller capable of control-ling the nonlinearities.In this study,a pressure-tube-type SCWR was controlled during reactor power maneuvering with a higher order sliding mode,and the reactor outgoing steam temperature and pressure were controlled simultaneously.In an SCWR,the temperature,pressure,and power must be maintained at a setpoint(desired value)during power maneuvering.Reactor point kinetics equations with three groups of delayed neutrons were used in the simulation.Higher-order and classic sliding mode controllers were separately manufactured to control the plant and were compared with the PI controllers speci-fied in previous studies.The controlled parameters were reactor power,steam temperature,and pressure.Notably,for these parameters,the PI controller had certain instabilities in the presence of disturbances.The classic sliding mode controller had a higher accuracy and stability;however its main drawback was the chattering phenomenon.HOSMC was highly accurate and stable and had a small computational cost.In reality,it followed the desired values without oscillations and chattering.
文摘Perilla frutescens seed (PFS) oil is reported to inhibit skin photoaging;however, its effect on melanogenesis has not yet been investigated. Herein, we tested the anti-melanogenesis activity of an oil-based extract from PFS with supercritical carbon dioxide (scCO<sub>2</sub>). In a cell culture system, B16 mouse melanoma cells were treated with the PFS scCO<sub>2</sub> extract and other samples. The PFS scCO<sub>2</sub> extract decreased melanin production by approximately 90% in B16 mouse melanoma cells without cytotoxicity at 100 μg/mL. This effect was greater than that of the well-known melanogenesis inhibitor, kojic acid. Although a hexane-extracted PFS oil and a squeezed PFS oil also decreased melanin production in the B16 cells, the inhibitory effect of the PFS scCO<sub>2</sub> extract was higher than both of these. Chemical analysis of the PFS scCO<sub>2</sub> extract and squeezed PFS oil showed that almost 90% of the components of both oils were α-linolenic acid, linoleic acid, and oleic acid. Furthermore, the ratio of those three fatty acids across both samples was almost the same. When the three fatty acids were mixed in the same ratio as in the PFS scCO<sub>2</sub> extract, the IC<sub>50</sub> of the mixture for melanin production in B16 melanoma cells was identical to that of the PFS scCO<sub>2</sub> extract. However, the IC<sub>50</sub> of the squeezed PFS oil was approximately 6.6 times higher than that of the mixture. Although those fatty acids are the main inhibitory ingredients against melanin production in all of the extracts, some factor(s) in the squeezed PFS reduce their affinity with the cells. These results indicated that the PFS scCO<sub>2</sub> extract could be a superior melanogenesis inhibitor. Although its main ingredients are probably the same as those of the squeezed PFS oil, it is necessary to extract with scCO<sub>2</sub> for stronger anti-melanogenesis activity.
基金This work was supported by the Natural Science Basic Research Program of Shaanxi[No.2022JQ-2912021JQ-234]+1 种基金the China Postdoctoral Science Foundation[No.2021M692735]the Fundamental Research Funds for the Central Universities,Chang'an University[No.300102271305].
文摘Since the mechanisms of methane-mudstone interactions are important for estimating shale gas reserves,methane adsorption under supercritical conditions of 30 MPa pressure and 303.15,333.15,363.15 K temperatures was studied to measure the excess methane adsorption in two mudstone samples from Yanchang Formation,Ordos Basin.Excess adsorption features inflection points where the amount of adsorbed gas changes from increasing to decreasing concentrations.Three methods(fixed,slope,and freely fitted density)were applied to calculate the adsorbed-phase density(rad),which was then used to fit the measured excess adsorption.Two criteria,the goodness-of-fit and whether the fitting can obtain reasonable absolute adsorption,were applied to determine the most accurate model.Results indicated that the supercritical Dubinin-Radushkevich(SDR)model with freely fitted rad was the most reasonable model.The volume of adsorbed methane at 363.15 K is close to the micropore(d<2 nm)volume of the corresponding mudstone.Considering the actual geological conditions,the adsorbed gas should be predominantly stored in micropores.Thermodynamic parameters reveal that the methane adsorption on mudstone is a physisorption process that is jointly controlled by the heterogeneity of,and interaction forces between the methane molecule and,the rock surface.
基金funded by the National Natural Science Foundation of China(Grant Nos.42141009,41825018,41888101 and 41902289)the Key Research Program of the Institute of Geology and Geophysics,CAS(Grant No.IGGCAS-202201)the Second Tibetan Plateau Scientific Expedition and Research Program(STEP)(Grant No.2019QZKK0904)。
文摘Supercritical carbon dioxide(ScCO_(2))fracturing has great advantages and prospects in both shale gas exploitation and CO_(2)storage.This paper reviews current laboratory experimental methods and results for sedimentary rocks fractured by ScCO_(2).The breakdown pressure,fracture parameters,mineral composition,bedding plane angle and permeability are discussed.We also compare the differences between sedimentary rock and granite fractured by ScCO_(2),ultimately noting problems and suggesting solutions and strategies for the future.The analysis found that the breakdown pressure of ScCO_(2)was reduced 6.52%–52.31%compared with that of using water.ScCO_(2)tends to produce a complex fracture morphology with significantly higher permeability.When compared with water,the fracture aperture of ScCO_(2)was decreased by 4.10%–72.33%,the tortuosity of ScCO_(2)was increased by 5.41%–70.98%and the fractal dimension of ScCO_(2)was increased by 4.55%–8.41%.The breakdown pressure of sandstone is more sensitive to the nature of the fracturing fluid,but fracture aperture is less sensitive to fracturing fluid than for shale and coal.Compared with granite,the tortuosity of sedimentary rock is more sensitive to the fracturing fluid and the fracture fractal dimension is less sensitive to the fracturing fluid.Existing research shows that ScCO_(2)has the advantages of low breakdown pressure,good fracture creation and environmental protection.It is recommended that research be conducted in terms of sample terms,experimental conditions,effectiveness evaluation and theoretical derivation in order to promote the application of ScCO_(2)reformed reservoirs in the future.
基金funded by the Henan Institute for Chinese Development Strategy of Engineering&Technology(Grant No.2022HENZDA02)the China Scholarship Council(No.202208080058).
文摘As an emerging waterless fracturing technology,supercritical carbon dioxide(SC-CO_(2))fracturing can reduce reservoir damage and dependence on water resources,and can also promote the reservoir stimulation and geological storage of carbon dioxide(CO_(2)).It is vital to figure out the laws in SC-CO_(2)fracturing for the large-scale field implementation of this technology.This paper reviews the numerical simulations of wellbore flow and heat transfer,fracture initiation and propagation,and proppant transport in SC-CO_(2)fracturing,including the numerical approaches and the obtained findings.It shows that the variations of wellbore temperature and pressure are complex and strongly transient.The wellhead pressure can be reduced by tubing and annulus co-injection or adding drag reducers into the fracturing fluid.Increasing the temperature of CO_(2)with wellhead heating can promote CO_(2)to reach the well bottom in the supercritical state.Compared with hydraulic fracturing,SC-CO_(2)fracturing has a lower fracture initiation pressure and can form a more complex fracture network,but the fracture width is narrower.The technology of SC-CO_(2)fracturing followed by thickened SC-CO_(2)fracturing,which combines with high injection rates and ultra-light proppants,can improve the placement effect of proppants while improving the complexity and width of fractures.The follow-up research is required to get a deeper insight into the SC-CO_(2)fracturing mechanisms and develop cost-effective drag reducers,thickeners,and ultra-light proppants.This paper can guide further research and promote the field application of SC-CO_(2)fracturing technology.
基金support by the Scientific Research Start-up Funds for introducing Talent in the Sichuan University (20822041C4014)National Science and Technology Major Project of China (2017-I-0004-0004)。
文摘The flow and heat transfer characteristics of n-decane in the sub-millimeter spiral tube(SMST) at supercritical pressure(p = 3 MPa) are studied by the RNG k-ε numerical model in this paper. The effects of various Reynolds numbers(Re) and structural parameters pitch(s) and spiral diameter(D) are analyzed.Results indicate that the average Nusselt numberNu and friction factorNu increase with an increase in Re, and decrease with an increase in D/d(tube diameter). In terms of the structural parameter s/d, it is found that as s/d increases, the Nu first increase, and then decrease. and the critical structural parameter is s/d = 4. Compared with the straight tube, the SMST can improve Nu by 34.8% at best, while it can improve Nu by 102.1% at most. In addition, a comprehensive heat transfer coefficient is applied to analyze the thermodynamic properties of SMST. With the optimal structural parameters of D/d = 6 and s/d = 4, the comprehensive heat transfer factor of supercritical pressure hydrocarbon fuel in the SMST can reach 1.074. At last, correlations of the average Nusselt number and friction factor are developed to predict the flow and heat transfer of n-decane at supercritical pressure.
基金Supported by the Project of the Academic Department of the Chinese Academy of Sciences (KKBE170026)Project of Science and Technology Department of Sinopec (P21039-3,P20049-1)Independent Research and Development Project of Sinopec Petroleum Exploration and Development Research Institute (YK-2021-29-2)。
文摘To investigate the impacts of water/supercritical CO_(2)-rock interaction on the micro-mechanical properties of shale,a series of high-temperature and high-pressure immersion experiments were performed on the calcareous laminated shale samples mined from the lower submember of the third member of Paleogene Shahejie Formation in the Jiyang Depression,Bohai Bay Basin.After that,grid nanoindentation tests were conducted to analyze the influence of immersion time,pressure,and temperature on micro-mechanical parameters.Experimental results show that the damage of shale caused by the water/supercritical CO_(2)-rock interaction was mainly featured by the generation of induced fractures in the clay-rich laminae.In the case of soaking with supercritical CO_(2),the aperture of induced fracture was smaller.Due to the existence of induced fractures,the statistical averages of elastic modulus and hardness both decreased.Meanwhile,compaction and stress-induced tensile fractures could be observed around the laminae.Generally,the longer the soaking time,the higher the soaking pressure and temperature,the more significant the degradation of micro-mechanical parameters is.Compared with water-rock interaction,the supercritical CO_(2)-rock interaction caused a lower degree of mechanical damage on the shale surface.Thus,supercritical CO_(2)can be used as a fracturing fluid to prevent the surface softening of induced fractures in shale reservoirs.
文摘[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface methodology. [Results] The optimum extraction conditions of black tea extract by supercritical CO_(2) extraction were as follows: extraction pressure 23.53 MPa, extraction time 1.73 h, and extraction temperature 49.75 ℃, with which the extract yield could reach 5.15% theoretically. [Conclusions] Based on the traditional extraction process, a supercritical extraction method optimized by response surface methodology and a unique extraction process were formed, which enriches the extraction processes and methods of natural raw materials.
文摘In this paper, a system of Lorenz-type ordinary differential equations is considered and, under some assumptions about the parameter space, the presence of the supercritical non-degenerate Hopf bifurcation is demonstrated. The technical tool used consists of the Central Manifold theorem, a well-known formula to calculate the Lyapunov coefficient and Hopf’s Theorem. For particular values of the parameters in the parameter space established in the main result of this work, a graph is presented that describes the evolution of the trajectories, obtained by means of numerical simulation.
基金financially supported by the National Natural Science Foundation of China(No.21874153)Science Foundation of China University of Petroleum,Beijing(No.2462017BJB09)PetroChina Innovation Foundation(No.2016D-5007-0402)。
文摘An efficient and environment-friendly method for simultaneous determination of 13 typical derivatives of polycyclic aromatic hydrocarbon(PAH)in petroleum-polluted soil with nitro-,oxy-and alkylfunctional group was developed using supercritical fluid extraction(SFE)followed by ultra-high performance supercritical fluid chromatography(UHPSFC).Parameters of UHPSFC,including type of stationary phase and mobile phase modifiers,gradient elution process,backpressure,column temperature,and the flow rate of mobile phase,were systematically optimized,achieving a fast separation within4.2 min.Limits of detection(LOD)were 0.005-0.1μg mL^(-1)or 0.1-2.0 ng g^(-1),respectively,with a good repeatability(RSD<5.0%).Before UHPSFC-PDA analysis,the PAH-derivatives in soil samples were effectively enriched in 15.0 min using SFE with an online carbon nanotubes(CNTs)collection trap.The soil samples were analyzed by the proposed method and the results were verified by GC-MS.Thus,SFE equipped with an online CNTs trap followed by UHPSFC-PDA analysis,which only consumed about2.0 mL organic solvent for a whole run,has been demonstrated to be an efficient way for screening and quantitative analysis of trace-level PAH-derivatives in soil samples.
基金supported by Research Fund for the Doctoral Program of Higher Education (China,No.20050010014)
文摘A series of nanosized Co/Zn/Mn/K composite catalysts for Fischer-Tropsch synthesis (FTS) were prepared by supercritical fluid drying (SCFD) method and common drying (CD) method. The nanosized cobalt-based catalysts were characterized by XRD, TEM and BET techniques. Their catalytic performances were tested in a slurry-bed reactor under FTS reaction conditions. The drying and crystallization were carried out simultaneously during SCFD, therefore, the catalysts prepared by SCFD method have ideal structure and show the FTS performance superior to the others prepared by CD method. The FTS activity and selectivity were improved via adding Zn, Mn and K promoters, and less CH4 and CO2 as well as higher yield of C5+ products were achieved. The optimal performance of a 92% CO conversion and a 65% C5+ product yield was obtained over a catalyst with the component of Co/Zn/Mn/K = 100/50/10/7. Furthermore, the catalytic performance was studied under the conditions of liquid-phase and supercritical phase slurry-bed, and C5+ product yield were 57.4% and 65.4%, respectively. In summary, better catalytic performance was obtained using the nanosized catalyst prepared by SCFD method under supercritical reaction conditions, resulting in higher conversion of CO, less CO2 byproduct, and higher yield of C5+ products.
文摘In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC is not yet applied for drug quality control in the daily routine framework. Among the numerous reported SFC methods, none of them could be found to fully satisfy to all steps of the analytical method lifecycle. Thereby, the present contribution aims to provide an overview of the current and past achievements related to SFC techniques, with a targeted attention to this lifecycle and its successive steps. The included discussions were therefore structured accordingly and emphasizing the analytical method lifecycle in accord with the International Conference on Harmonisation (ICH). Recent and important scientific outputs in the field of analytical SFC, as well as instrumental evolution, qualification strategies, method development methodologies and discussions on the topic of method validation are reviewed.
文摘It is well known that seawater that migrates deep into the Earth’s crust will pass into its supercritical domain at temperatures above 407°C and pressures above 298 bars. In the oceanic crust, these pressures are attained at depths of 3 km below sea surface, and sufficiently high temperatures are found near intruding magmas, which have temperatures in the range of 800°C to 1200°C. The physico-chemical behaviour of seawater changes dramatically when passing into the supercritical domain. A supercritical water vapour (ScriW) is formed with a density of 0.3 g/cc and a strongly reduced dipolar character. This change in polarity is causing the ScriW to lose its solubility of the common sea salts (chlorides and sulphates) and a spontaneous precipitation of sea salts takes place in the pore system. However, this is only one of many cases where the very special properties of ScriW affect its surroundings. The objective of this paper is to increase awareness of the many geological processes that are initiated and governed by ScriW. This includes interactions between ScriW and its geological surroundings to initiate and drive processes that are of major importance to the dynamics and livelihood of our planet. ScriW is the driver of volcanism associated with subduction zones, as ScriW deriving from the subduction slab is interacting with the mantle rocks and reducing their melting point. ScriW is also initiating serpentinization processes where olivines in the mantle rocks (e.g. peridotite) are transformed to serpentine minerals upon the uptake of OH-groups from hydrolysed water. The simultaneous oxidation of Fe2+ dissolved from iron-bearing pyroxenes and olivines leads to the formation of magnetite and hydrogen, and consequently, to a very reducing environment. ScriW may also be the potential starter and driver of the poorly understood mud and asphalt volcanism;both submarine and terrestrial. Furthermore, the lack of polarity of the water molecules in ScriW gives the ScriW vapour the potential to dissolve organic matter and petroleum. The same applies to supercritical brines confined in subduction slabs. If these supercritical water vapours migrate upwards to reach the critical point, the supercritical vapour is condensed into steam and dissolved petroleum is partitioned from the water phase to become a separate fluid phase. This opens up the possibility of transporting petroleum long distances when mixed with ScriW. Therefore, we may, popularly, say that ScriW drives a gigantic underground refinery system and also a salt factory. It is suggested that the result of these processes is that ScriW is rejuvenating the world’s ocean waters, as all of the ocean water circulates into the porous oceanic crust and out again in cycles of less than a million years. In summary, we suggest that ScriW participates in and is partly responsible for: 1) Ocean water rejuvenation and formation;2) Fundamental geological processes, such as volcanism, earthquakes, and meta-morphism (including serpentinization);3) Solid salt production, accumulation, transportation, and (salt) dome formation;4) The initiation and driving of mud, serpentine, and asphalt volcanoes;5) Dissolution of organic matter and petroleum, including transportation and phase separation (fractionation), when passing into the subcritical domain of (liquid) water.
文摘In this paper, we show that supercritical fluids have a greater significance in the generation of pegmatites,and for ore-forming processes related to granites than is usually assumed. We show that the supercritical melt or fluid is a silicate phase in which volatiles; principally H_2O are completely miscible in all proportions at magmatic temperatures and pressures. This phase evolves from felsic melts and changes into hydrothermal fluids, and its unique properties are particularly important in sequestering and concentrating low abundance elements, such as metals. In our past research, we have focused on processes observed at upper crustal levels, however extensive work by us and other researchers have demonstrated that supercritical melt/fluids should be abundant in melting zones at deep-crustal levels too. We propose that these fluids may provide a connecting link between lower and upper crustal magmas,and a highly efficient transport mechanism for usually melt incompatible elements. In this paper, we explore the unique features of this fluid which allow the partitioning of variouselements and compounds, potentially up to extreme levels,and may explain various features both of mineralization and the magmas that produced them.
文摘Environmentally benign carbon dioxide offers significant potential in its supercritical fluid phase to replace current reliance on a range of hazardous, relatively expensive and environmentally damaging organic solvents that are used on an extensive global basis. The unique combination of the physical properties of supercritical fluids are being exploited and further researched to continue the development and establishment of high efficiency, compact plant to provide energy and water efficient manufacturing processes. This mini-review is focused on the use and potential applications of supercritical fluid carbon dioxide for a selected range of key and emerging industrial processes as a sustainable alternative to totally eliminate or greatly reduce the requirement of numerous conventional organic solvents. Examples of the industries include: chemical extraction and purification, synthetic chemical reactions including polymerization and inorganic catalytic processes. Biochemical reactions involving enzymes, particle size engineering, textile dyeing and advanced material manufacture provide further illustrations of vital industrial activities where supercritical fluid technology processes are being implemented or developed. Some aspects relating to the economics of sustainable supercritical fluid carbon dioxide processes are also considered.