Dynamic evolution in mechanical characteristics of complex supporting structures during large section tunnel construction

The shallow tunnelling method(STM)often uses temporary supports to divide large section tunnels into several closed or semiclosed sections so as to share the upper load.The complex support system composed of primary and temporary supports can ensure safety during tunnel construction.Based on the large section tunnel of Beijing Subway Line 12,the mechanical characteristics of support system by the double-side-drift method(DSDM)during excavation and demolition were analyzed through numerical simulation and monitoring.The study showed that the middle cave excavation was the most critical stage of the DSDM,during which the load on the supporting structure increased significantly.The temporary vertical support bore most of the new load during middle cave excavation.During the demolition stage,the load was redistributed,which caused arch settlement and section convergence.The removal of the temporary vertical support exerted the greatest impact in this process.The lateral temporary inverted arch changed from axial compression to axial tension after the middle and lower caves were excavated.Based on the mechanical characteristics of the support system,some engineering suggestions were proposed for large section tunnel construction.These research results can provide reference for the design and construction of similar large section tunnels.

An automatic optimization method for minimizing supporting structures in additive manufacturing

The amount of supporting structure usage has been a major research topic in layer-based additive manufacturing(AM)over the past years as it leads to increased fabrication time and decreased surface quality.Previous studies focused on deformation and topology optimization to eliminate the number of support structures.However,during the actual fabrication process,the properties of shape and topology are essential.Therefore,they should not be modified casually.In this study,we present an optimizer that reduces the number of supporting structures by identifying the prime printing direction.Without rotation,models are projected in each direction in space,and the basis units involved in the generation of support structures are separated.Furthermore,the area of the supporting structures is calculated.Eventually,the prime printing direction with minimal supporting area is obtained through pattern-searching method.The results of the experiment demonstrated that the printing area was reduced by up to 60%for some cases,and the surface quality was also improved correspondingly.Furthermore,both the material consumption and fabrication time were decreased in most cases.In future work,additional factors will be considered,such as the height of the supporting S Xiao-Jun Chen xiaojunchen@sjtu.edu.cn 1 Institute of Biomedical Manufacturing and Life Quality Engineering,State Key Laboratory of Mechanical System and Vibration,School of Mechanical Engineering,Shanghai Jiao Tong University,Shanghai 200240,P.R.China 2 OMFS-IMPATH Research Group,Department of Imaging and Pathology,Faculty of Medicine,Katholieke Universiteit Leuven,Leuven,Belgium 3 Department of Oral and Maxillofacial Surgery,University Hospitals Leuven,Leuven,Belgium structures and the adhesion locations to improve the efficiency of this optimizer.

A multi-purpose prototype test system for mechanical behavior of tunnel supporting structure: Development and application

A multi-purpose prototype test system is developed to study the mechanical behavior of tunnel sup-porting structure,including a modular counterforce device,a powerful loading equipment,an advanced intelligent management system and an efficient noncontact deformation measurement system.The functions of the prototype test system are adjustable size and shape of the modular counterforce structure,sufficient load reserve and accurate loading,multi-connection linkage intelligent management,and high-precision and continuously positioned noncontact deformation measurement.The modular counterforce structure is currently the largest in the world,with an outer diameter of 20.5 m,an inner diameter of 16.5 m and a height of 6 m.The case application proves that the prototype test system can reproduce the mechanical behavior of the tunnel lining during load-bearing,deformation and failure processes in detail.

Sensor monitoring of a newly designed foundation pit supporting structure

A new type of pit supporting structure, which was tested and verified using the sensor monitoring technology, was presented. The new supporting structure is assembled by prefabricated steel structural units. The adjacent steel structural units are jointed with fasteners, and each steel structural unit has a certain radian and is welded by two steel tubes and one piece of steel disc. In order to test and verify the reliability of the new supporting structure, the field tests are designed. The main monitoring programs include the hoop stress of supporting structure, lateral earth pressure, and soil deformation. The monitoring data of the field tests show that the new supporting structure is convenient, reliable and safe.

Application of modified polypropylene （crude） fibers concrete to strengthen the support structures in deep mine roadway

The an thors developed a new composite cement base material by mixing the high tenacity polypropylene （coarse） fiber in plain cement base for the cement-layer-spray technology. By studying the key parameters of the fiber dosage, the spray layer thickness, and the fiber reinforced concrete injection time, etc. It is found that the ideal volume ratio of polypropylene （crude） fiber is 0.8% （V/V）, and the secondary lining fiber concrete spraying should start when the shrinkage rate is lower than 0.5 mm/d, and the optimal thickness of shotcrete is 120 mm. The supporting effects and the economic benefits were studied using a real project practice, and the result obtained can be a good reference for practical applications of this new supporting material in the future.

Application of Modified Genetic Algorithm to Optimal Design of Supporting Structure

The modified genetic algorithm was used for the optimal design of supporting structure in deep pits.Based on the common genetic algorithm, using niche technique and reserving the optimum individual the modified genetic algorithm was presented. By means of the practical engineering, the modified genetic algorithm not only has more expedient convergence, but also can enhance security and operation efficiency.

Multi-criteria assessment of offshore wind turbine support structures based on dynamic property optimization

Increasing size of wind turbine and deep water deployment have raised the issue of appropriate selection of the most suitable support structure to make offshore wind energy cost competitive.The paper presents an optimization methodology for decision making process of bottom mounted supports of offshore wind turbines （OWTs） through reasonable engineering attributes derivation.Mathematic models of support structures are reduced by the generalized single-degree-of-freedom theory with relatively fewer structural parameters.Soft-stiff design optimization based on dynamic properties of OWTs is performed for monopile and lattice supports with different wind turbines,water depth and hub height.Attributes of support structures,wind turbines and environment conditions are applied in the multi-criteria decision making method——TOPSIS for benchmarking of those options.The results illustrate the effectiveness of the proposed optimazation methodology combined with economical and environmental attributes together.

REQUIREMENTS AND DESIGN METHOD FOR MATCHING AIRCRAFT GUNS WITH THEIR SUPPORTING STRUCTURE

In aircraft structural dynamic design the matching of guns with their supporting structure is one of the most important tasks on which hinges the success or failure of the structural design. The design curves for matching guns with their supporting structure can be obtained from response calculations of the plate-spring system supporting the gun on the ground,the model structure tested on the ground and the actual structure.A set of matching curves is given for engineering application.Then,the matching design can be accomplished by means of impact load spectrograms so as to perform an optimal structural design and to make further improvements on dynamic design program.

Predicting the strut forces of the steel supporting structure of deep excavation considering various factors by machine learning methods

The application of steel strut force servo systems in deep excavation engineering is not widespread,and there is a notable scarcity of in-situ measured datasets.This presents a significant research gap in the field.Addressing this,our study introduces a valuable dataset and application scenarios,serving as a reference point for future research.The main objective of this study is to use machine learning(ML)methods for accurately predicting strut forces in steel supporting structures,a crucial aspect for the safety and stability of deep excavation projects.We employed five different ML methods:radial basis function neural network(RBFNN),back propagation neural network(BPNN),K-Nearest Neighbor(KNN),support vector machine(SVM),and random forest(RF),utilizing a dataset of 2208 measured points.These points included one output parameter(strut forces)and seven input parameters(vertical position of strut,plane position of strut,time,temperature,unit weight,cohesion,and internal frictional angle).The effectiveness of these methods was assessed using root mean square error(RMSE),correlation coefficient(R),and mean absolute error(MAE).Our findings indicate that the BPNN method outperforms others,with RMSE,R,and MAE values of 72.1 kN,0.9931,and 57.4 kN,respectively,on the testing dataset.This study underscores the potential of ML methods in precisely predicting strut forces in deep excavation engineering,contributing to enhanced safety measures and project planning.

Tunnel Support Structure System and Its Synergy

The tunnel support system is composed of lining,bolt,and steel frame.It is of great significance to effectively control the deformation of the surrounding rock of the tunnel,make full use of the characteristics of different support methods,and formulate an economical and effective support plan to ensure the safe operation of the tunnel structure.This paper clarifies the synergistic relationship between the support structure and the surrounding rock based on their fundamental characteristics and functions.Various support structures and components are also discussed in this paper.Additionally,the paper presents an optimized design of the tunnel support structure system.

Mechanism and control technology of strong ground pressure behaviour induced by high-position hard roofs in extra-thick coal seam mining

This work aimed at revealing the mechanism of strong ground pressure behaviour(SGPB)induced by high-position hard roof(HHR).Based on the supporting structures model of HHR,a modified voussoir beam mechanical model for HHR was established by considering the gangue support coefficient,through which the modified expressions of limit breaking span and breaking energy of HHR were deduced.Combined with the relationship between the dynamic-static loading stress of supporting body(hydraulic support and coal wall)and its comprehensive supporting strength,the criteria of ground pressure behaviour(GPB)induced by HHR were discussed.The types of Ⅰ_(1),Ⅰ_(2),Ⅱ_(1),andⅡ_(2) of GPB were interpreted.Results showed that types Ⅰ_(1) and Ⅰ_(2) were the main forms of SGPB in extra-thick coal seam mining.The main manifestation of SGPB was static stress,which was mainly derived from the instability of HHR rather than fracture.Accordingly,an innovative control technology was proposed,which can weaken static load by vertical-well separated fracturing HHR.The research results have been successfully applied to the 8101 working face in Tashan coal mine,Shanxi Province,China.The results of a digital borehole camera observation and stress monitoring proved the rationality of the GPB criteria.The control technology was successful,paving the way for new possibilities to HHR control for safety mining.

Tunnel design considering stress release effect

In tunnel design, the determination of installation time and the stiffness of supporting structures is very important to the tunnel stability. This study used the convergence-confinement method to determine the stress and displacement of the tunnel while considering the counter-pressure curve of the ground base, the stress release effect, and the interaction between the tunnel lining and the rock surrounding the tunnel chamber. The results allowed for the determination of the installation time, distribution and strength of supporting structures. This method was applied to the intake tunnel in the Ban Ve Hydroelectric Power Plant, in Nghe An Province, Vietnam. The results show that when a suitable displacement u0 ranging from 0.0865 m to 0.0919 m occurrs, we can install supporting structures that satisfy the stability and economical requirements.

Stability influence factors analysis and construction of a deep beam anchorage structure in roadway roof

Deep beam anchorage structures based on spatial distribution analysis of the cable prestressed field have been proposed for roadway roof support, Stability and other factors that influence deep beam structures are studied in this paper using mechanical calculations, numerical analysis and field measurements, A mechanical model of deep beam structure subjected to multiple loading is established, including analysis of roof support in the return airway of S1203 working face in the Yuwu coal mine, China, The expression of maximum shear stress in the deep beam structure is deduced according to the stress superposition criterion, It is found that the primary factors affecting deep beam structure stability are deep beam thickness, cable pre-tension and cable spacing, The variation of maximum shear stress distribution and prestressed field diffusion effects according to various factors are analyzed using Matlah and FLAC3DTM software, and practical support parameters of the S1203 return airway roof are determined, According to the observations of rock pressure, there is no evidence of roof separation, and the maximum values of roof subsidence and convergence of wall rock are 72 and 48 mm, respectively, The results show that the proposed roof support design with a deep beam structure is feasible and achieves effective control of the roadway roof,

The development of 3D printing technology and the current situation of controlling defects in SLM technology

With unique manufacturing technology,the additive manufacturing technology divides the three-dimensional object into countless two-dimensional laminates.Compared with the traditional material reduction manufacturing method,it has the characteristics of saving materials,being fast,and especially suitable for single and small batch parts and the rapid manufacturing of parts with complex shapes and internal structures.In this paper,various methods of additive manufacturing technology are reviewed.This paper introduces the characteristics of selective laser melting technology and its forming equipment system.On this basis,the technical defects of selective laser melting technology are analyzed,and the status of controlling defects in SLM technology is explained.In the end,the prospects of additive manufacturing technology are described.

Thermal Structure of Glass Fiber Reinforce Plastic Support Structure

The assembled form of thick-wall glass fiber reinforced plastics (GFRP) tube and 0Cr18Ni9 austenitic stainless steel pipes was designed as the radius thermal-insulating and load-supporting structure in cryogenic vessels. In order to study the thermal leakage and gap changes on the support structure, as well as radius temperature and stress distribution on GFRP tube, an experimental investigation has been taken. The results indicate that the support structure is proved to fit well as thermal-insulating and load-supporting part in cryo-genic vessels, furthermore has high security during cryogenic applications.

A Lower Rigid Support Structure for the HT-7U Vacuum Vessel

Vacuum vessel of the HT-7U is a fully welded toroidal structure with a noncircular cross-section nested in the bore of the TF coils. According to the requirement of the physics design, sixteen horizontal ports on outboard mid-plane and thirty-two vertical ports on the top and bottom are designed for diagnostics, plasma heating, current driving, vacuum pumping and gas puffing. Bellows on these port necks are used for flexible components to absorb the relative displacement in radial and vertical directions due to external load, thermal expansion or contrac-tion and assembly tolerance, and also used for isolation of mechanical vibration. For the support system of vacuum vessel it should be not only strong enough to withstand forces acting on the vessel interior components and the vessel itself due to the dead weight and electromagnetic inter-actions during plasma disruption, but also sufficiently flexible to be suited to thermal expansion during baking. In order to solve this contradiction a new kind of low rigid support has been designed, which has a perfectly rigid in vertical direction and perfectly soft in radial direction. Some three-dimension finite element COSMOS models were performed to analyze their structural strength, stiffness and fatigue life, with an emphasis on the static stress analysis. The load spectra during vacuum vessel operation were also simulated on these models in the view of fatigue design. It was confirmed that the bellows and support had sufficient strength in the designed range of the load conditions. The results showed that the peak stress on bellows was 87 MPa and on the support system was 97 MPa. Now all kinds of bellows and support system have been designed. In order to accumulate some engineering experiences and probe into some molding die and welding technologies, prototypical bellows and support system have been fabricated. At the same time a mechanical testing apparatus was designed for proof tests on the prototypical bellows and support to verify their functional and structure capability. The experimental data indicated that the re-sults of finite element analysis were coincident with experimental test results. It has been proved that the present vacuum vessel's bellows and support system are reasonable and feasible.

Variation of hydraulic parameters with different wing of a T-shape spur dike in bend channels

In the present research,by using a numerical model,some analyses were performed on flows around a T-shape spur dike and a support structure located at its upstream under different wing to length ratios of T-shape spur dike in the order of 0.25,0.50,0.75 and 1.00.In order to verify numerical model,physical model data were used in presence of a single T shape spur dike.Results from numerical model are desirably in agreement with those of physical one because the regression between both data is 0.86 up to 0.92.In this research,all hydraulic parameters of flows,streamlines and dimensions of flow separation zones were studied in order to select the most practical model.Increased W/L results in 7%–12%increase in the length of flow separation zone and in 2%increase in the width of this zone compared to W/L=0.25.

Neuron-fibrous scaffold interfaces in the peripheral nervous system: a perspective on the structural requirements

The nerves of the peripheral nervous system are not able to effectively regenerate in cases of severe neural injury.This can result in debilitating consequences,including morbidity and lifelong impairments affecting the quality of the patient’s life.Recent findings in neural tissue engineering have opened promising avenues to apply fibrous tissue-engineered scaffolds to promote tissue regeneration and functional recovery.These scaffolds,known as neural scaffolds,are able to improve neural regeneration by playing two major roles,namely,by being a carrier for transplanted peripheral nervous system cells or biological cues and by providing structural support to direct growing nerve fibers towards the target area.However,successful implementation of scaffold-based therapeutic approaches calls for an appropriate design of the neural scaffold structure that is capable of up-and down-regulation of neuron-scaffold interactions in the extracellular matrix environment.This review discusses the main challenges that need to be addressed to develop and apply fibrous tissue-engineered scaffolds in clinical practice.It describes some promising solutions that,so far,have shown to promote neural cell adhesion and growth and a potential to repair peripheral nervous system injuries.

Design and Kinematics Analysis of Support Structure for Multi-Configuration Rigid-Flexible Coupled Modular Deployable Antenna

In order to meet the urgent need for diversified and multi-functional deployable antennas in many major national aerospace projects,such as interstellar exploration,the fourth phase of lunar exploration project,and the industrial application of Bei Dou,a deployable antenna structure composed of hexagonal prism and pentagonal prism modules is proposed.Firstly,the arrangement and combination rules of pentagonal prism and hexagonal prism modules on the plane were analyzed.Secondly,the spatial geometric model of the deployable antenna composed of pentagonal prism and hexagonal prism modules was established.The influence of module size on the antenna shape was then analyzed,and the kinematic model of the deployable antenna established by coordinate transformation.Finally,the above model was verified using MATLAB software.The simulation results showed that the proposed modular deployable antenna structure can realize accurate connection between modules,complete the expected deployment and folding functional requirements.It is hoped that this research can provide reference for the basic research and engineering application of deployable antennas in China.

Slicing and support structure generation for 3D printing directly on B-rep models

Traditional 3D printing is based on stereolithography or standard tessellation language models,which contain many redundant data and have low precision.This paper proposes a slicing and support structure generation algorithm for 3D printing directly on boundary representation(B-rep)models.First,surface slicing is performed by efficiently computing the intersection curves between the faces of the B-rep models and each slicing plane.Then,the normals of the B-rep models are used to detect where the support structures should be located and the support structures are generated.Experimental results show the efficiency and stability of our algorithm.