IMPROVING THE SURFACE PROPERTY OF TC4 ALLOY BY LASER NITRIDING AND ITS MECHANISM

The mixing technology of laser and heated nitrogen was applied to improve the surface hardness of titanium alloy （ TC4 ）. The samples were nitrided with laser power density of 6.S × 10^6SW. cm^-2, the scanning speed varioas from 100 to 500mm ·min^-1. The nitrogen gas was pre-heated to 300℃ to accelerate the nitriding process. Some interested samples were tested with XRD method （X-ray diffraction） to analyze the composition of nitrides, and the surface hardness of HV was measured. The results show that TiN and Ti2N were formed on the surface of Ti alloy with proper nitriding parameters, but TiN is the main composition. The surface hardness increased by three times, which is from the original value of 269to 794kg·mm^-2. The mechanism of the mixing technology is considered mainly of the activation of nitrogen by laser power and the pre-heated process which accelerated the nitriding process. The nitridation process can be considered as six steps given in detail. The result by analyzing the mechanism of improving the surface property of TiAl alloy shows the improvement of surface property due to two factors： the first reason is the result of laser annealing, and the second one is the formation of TiN.

Au/TS-1 catalyst for propylene epoxidation with H_(2)and O_(2):Effect of surface property and morphology of TS-1 zeolite

The catalytic performances over propylene epoxidation with H_(2)and O_(2)(HOPO process)are significantly affected by the properties(e.g.,surface properties,Ti coordination,morphology)of titanosilicate zeolite.Introducing urea into zeolite synthesis is a simple and convenient method to modify these properties of titanosilicate zeolite.Uncalcined pore-blocked titanium silicalite-1(TS-1,i.e.,TS-1-B)with the lower urea dosage possesses more defective structure and unsaturated coordinated Ti sites verified by 29Si nuclear magnetic resonance(NMR)and X-ray photoelectron spectroscopy(XPS)analysis,which results in a high initial activity and hydrogen efficiency;while the high surface acidity generated by these Ti species leads to a continuous decrease in the activity and the propylene oxide(PO)selectivity during the reaction.As the amount of urea gradually increases,the TS-1-B samples present the reduced surface defects and defective and unsaturated Ti species.Specially,TS-1-B-0.30U presents the weaker PO adsorption on PO-diffusion reflectance infrared Fourier transform spectra(DRIFTS),thus results in the high stable PO formation rate and selectivity over its Au catalyst.Furthermore,a flat-plate-like shape with a shorter thickness of 100 nm along the b-axis direction is observed on the urea-modified TS-1.Compared with the conventional ellipsoidal TS-1 with crystal sizes of 200 and 500 nm,the flat-plate-like TS-1-0.30U displays the less surface defects,unsaturated Ti species,the weaker Lewis acid,which is favorable for the desorption and intracrystalline diffusion of PO,thus reduces the occurrence of side reactions for the improved selectivity and stability.This work may provide a reference for developing titanium-containing materials with high activity and stability over HOPO reaction.

Development and Evaluation of Stable Paracetamol Loaded Solid Dispersion with Enhanced Analgesic and Hepatoprotective Property

Paracetamol (PCM) is enlisted in the WHO model list as an essential medicine for pain and palliative care, but at overdose, it causes hepatic damage. This study was designed to assess the analgesic efficacy and hepatoprotective property of a solid dispersion (SD) loaded with PCM. A number of PCM loaded formulations (PSDs) were fabricated using silica alone or in combination with polyethylene glycol and/or Na-citrate followed by in-vitro dissolution profiling. Selected PSDs with improved dissolution profile were subjected to solid-state characterization (DSC, PXRD, FTIR, and SEM), stability study along with investigation of in-vivo analgesic efficacy and effect on hepatocytes. Among these, PSD10 showed a rapid and significantly higher in-vitro drug release than pure PCM. This improvement was distinct to other PSDs also. Solid-state characterization of PSD10 authenticated the conversion of crystalline PCM to amorphous form upon formulation. Subsequent oral administration of PSD10 in Swiss albino mice showed 1.44-fold greater analgesic efficacy than pure PCM at dose 30 mg/kg. Besides, at acute toxic dose, liver histology of PSD10 mice was comparable with NC mice indicating hepatic protection upon formulation, whereas the PCM mice showed extensive hepatic necrosis which was also endorsed by significantly higher values of SGPT, SGOT, and ALP than PSD10 mice. Finally, an accelerated stability study of PSD10 performed according to the guideline of ICH noticed no remarkable deviation in its dissolution performance as well as crystalline nature. Thus, this newly developed PSD10 may be a safe and promising alternative for pain management and palliative care.

Effect of dissolved components of malachite and calcite on surface properties and flotation behavior

In general,malachite is recovered via sulfidization–xanthate flotation,although many unsatisfactory flotation indexes are frequently obtained as a result of the presence of associated calcite.This phenomenon occurs because the dissolved components of malachite and calcite affect the flotation behavior of both minerals.In this study,the effect of the dissolved components derived from malachite and calcite on the flotation behavior and surface characteristics of both minerals was investigated.Flotation tests indicated that malachite recovery decreased when the calcite supernatant was introduced,while the presence of the malachite supernatant increased the recovery of calcite.Dissolution and adsorption tests,along with zeta potential measurements,X-ray photoelectron spectroscopy,Fourier transform infrared spectrometry,and timeof-flight secondary ion mass spectrometry demonstrated that the Ca species in the calcite supernatant were adsorbed on the malachite surface,which hindered the interaction of Na2S with malachite,thereby resulting in the insufficient adsorption of sodium isoamyl xanthate(NaIX)on the surface of malachite.By contrast,the Cu species in the malachite supernatant were adsorbed on the calcite surface,and they provided active sites for the subsequent adsorption of Na_(2)S and NaIX.

Study on the surface properties of surface modified silicone intraocular lenses

AIM: To prepare a new-type soft intraocular lens (IOL) that silicone intraocular lenses (IOLs) were modified by surface modification technique to assess IOLs biocompatibility. METHODS: With the technique of ion beam combined with low temperature and low pressure plasma, the surface characteristics of the IOLs including physical and optical properties were determined by the instruments of IOLs resolution, UV/VIS scanning spectrophotometer, contact angle measurement system, electron spectroscopy for chemical analysis (ESCA) and scanning electron microscope (SEM). RESULTS: The color of titanium (Ti) modified IOLs was light yellow and that of titanium nitride (TiN) modified IOLs was light brown. The absorptive degree of ultraviolet rays and the hydrophilicity of the surfaces of modified IOLs were increased, and appeared suitable chemical compositions. The resolution of unmodified and modified IOLs reached normal standard. The surfaces of unmodified and Ti-modified IOLs appeared uniform. The surfaces of TIN-modified IOLs presented fine porcelain structure. CONCLUSION: The optical properties of all IOLs and the surface morphology of the modified IOLs were not affected by modification processes. The surface properties of the modified IOLs were improved.

Effects of Atmospheric DBD Plasma Treatment on the Surface Properties of PAN-Based Carbon Fiber

Plasma treatment has been known as an effective way to improve the surface bonding between the reinforcement material and the matrix, by modifying the surface morphology and the chemical composes of the material. In order to investigate the effects of atmospheric dielectric barrier discharge (DBD) plasma treatment on the surface properties of polyacrylonitrile-based (PAN-based) carbon fiber, atomic force microscope(AFM), X-ray photoelectron spectroscopy(XPS), and contact angle test were introduced to compare different treatment duration. The interfacial adhesion of carbon fiber/epoxy (CF/EP) composites were analyzed by a single fiber composite (SFC) for filament fragmentation test. And the tensile strength test and Weibull analysis were carried out to observe whether the etching could affect the strength. The results prove that the DBD plasma improves the surface properties of the carbon fiber. Further, when the treatment time was around 90 s, the roughness and oxygen containing group of the carbon fiber reached the peak values. Also, the fiber showed the best adhesion to the polymer in contact angle test and the optimum interfacial shear strength (IFSS) in fragmentation test. The Weibull analyses of the tensile data revealed no substantial changes in the tensile strength within the treatment time of 180 s.

PREPARATION AND SURFACE PROPERTIES OF ACRYLIC COPOLYMERS CONTAINING FLUORINATED MONOMERS

A series of copolymers comprising butylmethacrylate, styrene, butylacrylate, hydroxypropyl acrylate and perfluoroalkyl methacrylate were synthesized by the free radical polymerization using BPO as an initiator. The surface property of the copolymer films was subsequently characterized. The contact angle measurements and energy dispersive analysis of X-ray （EDAX） show that the length and content of perfluoroalkyl side chains in the copolymers are crucial for the preparation of the film with low surface energy. At a given content of fluorinated monomers in the copolymers, the longer the perfluoroalkyl side chain, the larger the water contact angle of the copolymer films will be. On the other hand, the higher the content of fluorinated monomers, the lower the surface energy is. The water contact angle increases with the increase of the fluorinated monomer content and reaches a plateau at 3 wt% of fluorinated monomer content.

Approaches to Improving Selectivity During Photoelectrochemical Transformation of Small Molecules

Photoelectrochemical (PEC) small-molecule oxidation can selectively transform substrates into high-value-added fine chemicals and increase the rate of cathode hydrogen evolution. Nevertheless, achieving high-selectivity PEC oxidation of small molecules to produce specific products is a very challenging task. In general, selectivity can be improved by changing the surface catalyticsites of the photoanode and modulating the interfacial environments of the reactions. Herein, recent advances in approaches to improving selective PEC oxidation of small molecules are introduced. We first briefly discuss the basic concept and fundamentals of small-molecule PEC oxidation. The reported approaches to improving the performance of selective PEC oxidation of small molecules are highlighted from two aspects: (1) changing the surface properties of photoanodes by selecting suitable materials or modifying the photoanodes and (2) mediating the oxidation reactions using redox mediators. The PEC oxidation mechanism of these studies is emphasized. We also discuss the challenges in this research direction and offer a perspective on the further development of selective PEC-based small-molecule transformation.

Syntheses and Surface Properties of Polyacrylonitrile-based Copolymer Membranes Containing Sugar Moieties

To improve the hydrophilicity of polyacrylonitrile-based membranes, sugar moieties were incorporated into acrylonitrile-based copolymers via the radical copolymerization of α-allyl glucoside(AG) with acrylonitrile(AN) with 2,2′-azobis-iso-butyronitrile(AIBN) as the initiator in dimethyl sulphoxide(DMSO). It was found that the yield increased with the increase of the initiator concentration and reaction time, while it decreased with the increase of the monomer molar ratio of AG to AN. Raising the AG proportion in the monomer mixture resulted in the increase of the AG content in the copolymer. M_v of the copolymers decreased with increasing the AG monomer fraction in feed. The copolymers were fabricated into dense membranes and their surface properties were studied by means of the water contact angle measurement and platelet adhesion tests. It was found that the static water contact angle on the membrane decreased significantly from 70° to 33° with the increase of the AG content. The adhesive number of platelets on the membrane surface also decreased significantly with increasing AG content in the copolymers. These results demonstrate that the hydrophilicity and biocompatibility of the acrylonitrile-based copolymer membranes could be improved efficiently by the copolymerization of acrylonitrile with vinyl carbohydrates.

Influence of Surface Structure of Platinum Electrodes on Electrooxidation of CO

The oxidation of CO on platinum electrodes in an acid solution was studied with the conventional electrochemical methods and the on-line electrochemical mass spectroscopy. It was found that this reaction is strongly determined by the surface morphology of platinum. The pretreatment of platinum electrodes can change the surface properties dramatically, in consequence it can improve the electrocatalytic activity towards the electrooxidation of CO. The existence of surface active sites on the roughened platinum electrodes can be used to explain its high electrocatalysis towards the oxidation of CO.

Deposition of DLC Coating on Biomedical TiNi Alloys by Plasma Based Ion Implantation to Improve Surface Properties

Diamond-like carbon （DLC） films were successfully deposited on Ti- 50.8 at% Ni using plasma based ion implantation （PBII） technique. The influence of the pulsed negative bias voltage applied to the substrate from 12 kV to 40 kV on the microstracture, nano-indentation hardness and Young＇ s modulus, the surface characteristics and corrosion resistant property as well as hemocompatibility were investigated. The experimental resalts showed that C 1 s peak depended heavily on the bias voltage. With the increase of bias voltage, the ratio of sp2 / sp3 first decreased, reaching a minimum value at 20 kV, and then increased. The DLC coating deposited at 20 kV showed the highest hardness and elastic modulus values as a result of lower sp2/sp3 ratio. The RMS values first decreased from 7.202nm（12 kV） to 5.279 nm（20 kV）, and then increased to 11.449 nm（30 kV） and 7.060 nm（ 40 kV）. The uncoated TiNi alloy showed severe pitting corrosion, due to the presence of Cl-ions in the solution. On the contrary, the DLC coated sample showed very little pitting corrosion and behaved better corrosion resistant property especially for the specimens deposited at 20 kV bias voltages. The platelet adhesion test show that the hemocompatibility of DLC coated TiNi alloy is much better than that of bare TiNi alloy, and the hemocompatibility performance of DLC coated TiNi alloy deposited at 20 kV is superior to that of other coated specimens.

Surface Modification of Electrospun Poly(L-lactide)/Poly(ε-caprolactone)Fibrous Membranes by Plasma Treatment and Gelatin Immobilization

Biopolymer fibers have great potential for technical applications in biomaterials.The surface properties of fibers are of importance in these applications.In this study,electrospun poly(L-lactide)(PLLA)/poly(ε-caprolactone)(PCL)membranes were modified by cold plasma treatment and coating gelatin to improve the surface hydrophilic properties.The morphologies of the fibers were observed by scanning electron microscopy(SEM).Atomic force microscopy(AFM)was employed to show the surface characteristics of the fibers.The chemical feature of the fibrous membrane surfaces was examined by X-ray photoelectron spectroscopy(XPS).The surface wettability of the fibrous membrane was also characterized by water contact angle measurements.All these results show that plasma treatment can have profound effects on the surface properties of fibrous membranes by changing their surface physical and chemical features.Gelatin-PLLA/PCL membrane has great potential in applications of tissue engineering scaffolds.

Surface modification of wollastonite by the mechano-activated method and its properties

Surface modification of wollastonite particles using titanate as a modification agent incorporated by simultaneous wet ultra-fine grinding in a laboratory stirred mill was investigated.The physical,physic-chemical and application properties of the modified wollastonite were measured and evaluated.The results showed that grinding intensity markedly influences the modification effect because of the mechano chemical effect.The hydrophilic surface of wollastonite was turned into a hydrophobic one after modification.The interaction between titanate and wollastonite under wet grinding circumstances was studied.It was suggested that physical adsorption and chemical adsorption of titanate coexisted on the wollastonite surface.The mechanical properties of polyethylene（PE） filled with the modified wollastonite powder were markedly improved.

Bio-leaching effects of Leptospirillum ferriphilum on the surface chemical properties of pyrite

Leptospirillum ferriphilum cultured using different energy sources(either soluble ferrous ion or pyrite) changed the surface properties of pyrite.Cell adsorption,zeta-potential,hydrophobicty,FT-IR spectra and surface morphology were investigated.Adhesion of bacterial cells to the pyrite surface is a fast process.Furthermore,the adsorption of cells grown in pyrite is greater than of cells grown in soluble ferrous ion.The Iso-Electric Point(IEP) of pyrite treated with L.ferriphilum approaches that of the cells themselves.The contact angle of the pyrite surface was observed to decrease due to the surface formation of some hydrophilic substances during bio-leaching.Changes in pyrite surface properties after bacterial treatment support the idea that ferric ion plays an important role and that indirect bio-oxidation is the principal mechanism of pyrite bio-leaching.

Preparation and Surface Properties of Silicon-Containing Waterborne Polyurethane Functionalized with Fluorine-Containing Acrylate and Micro-Nano Silica

In order to prepare hydrophobic waterborne polyurethane coatings with better performances, the silicon-containing waterborne polyurethane（SiWPU） with functional chain extender hydroxyethyl acrylate（HEA） was prepared first, and then a series of silicon＆fluorine-containing polyurethane/acrylate（FSiPUA） emulsions were obtained with flourine containing acrylic monomer by seed emulsion polymerization, introducing micro-nano SiO2 into FSiPUA emulsion to make the final hybrid emulsion. The properties of Si WPU, FSiPUA and SiO2/FSiPUA were investigated by fourier transform infrared spectra（FTIR）, transmission electron microscope（TEM）, Scanning Electron Microscope（SEM） and some other analytical methods. The results revealed that FSiPUA emulsion particles possessed composite core-shell structure and FSiPUA films with suitable ratio performed better than Si WPU films in hardness, water resistance and solvent resistance. The SiO2/FSiPUA films with micro-nano dual roughness structure showed a water contact angle of 136° with good resistance to acid and alkali.

COMPARISON OF SURFACE PROPERTIES OF Ti-6Al-4V COATED WITH TITANIUM NITRIDE, TiN+TiC+Ti(C,N)/DLC, TiN/DLC AND TiC/DLC FILMS BY PLASMA-BASED ION IMPLANTATION

The surface properties of Ti-6Al-4V alloy coated with titanium nitride, TiN+TiC+Ti(C,N)/DLC (diamond like carbon), TiN/DLC and TiC/DLC films by plasma-based ion implantation (PBII) with nitrogen, PBII with nitrogen then acetylene, PBII with nitrogen then glow discharge deposition with acetylene plus hydrogen and PBII with acetylene then glow discharge deposition with acetylene plus hydrogen respectively were studied. The corresponding films are found getting dimmer, showing light gold or gold, smoky color (uneven), light red in black (uneven), and graphite black separately. The corresponding film resistivities are given. Antioxidation ability of the titanium nitride film is poor, while the existence of carbon (or carbide) improves the antioxidation ability of the films. Having undergone excellent intermediate transitional region of nitrogen and carbon implantation, the top DLC layer of the TiN+TiC+Ti(C,N)/DLC multilayer are formed after the carbon implantation has the best adhesion with the substrate among all the multilayers. Although microhardness of the samples increases in the order of coatings of titanium nitride, TiN/DLC, TiN+TiC+Ti(C,N)/DLC and TiC/DLC, the TiN/DLC and TiC/DLC multilayers have greater brittleness as compared with other films.

The Impact of Surface Properties on Downward Surface Shortwave Radiation over the Tibetan Plateau

The complexity of inhomogeneous surface-atmosphere radiation transfer is one of the foremost problems in the field of atmospheric physics and atmospheric radiation. To date, the influence of surface properties on shortwave radiation has not been well studied. The daily downward surface shortwave radiation of the latest FLASHFlux/CERES （Fast Longwave And Shortwave Fluxes_Time Interpolated and Spatially Averaged/Clouds and the Earth＇s Radiant Energy System） satellite data was evaluated against in situ data. The comparison indicated that the differences between the two data sets are unstable and large over rugged terrain compared with relatively flat terrain, and the mean absolute error of the satellite products reaches 31.4 W m-2 （12.3%） over rugged terrain. Based on the SSF （single satellite footprint）/CERES product, the influence of surface properties on the distribution of downward surface shortwave radiation （DSSR） was analyzed. The influence of surface properties on DSSR over the Tibetan Plateau is about twice as large as that in two other regions located at the same latitude （eastern China-western Pacific and subtropical North Pacific）. A simulation was carried out with the help of the I3RC （International Intercomparision of Three-Dimensional Radiation Code） Monte Carlo 3D radiative transfer community model. The results showed that DSSR increases as surface albedo increases. Moreover, the impact of surface albedo on DSSR is larger if the spatial distribution of clouds is more non-uniform. It is hoped that these results will contribute to the development of 3D radiative transfer models and the improvement of satellite inversion algorithms.

Effects of Zr/Ti molar ratio in SO_4^(2-)/ZrO_(2-)TiO_2 calcined at different temperatures on its surface properties and glucose reactivity in near-critical methanol

Effects of Zr/Ti molar ratio in SO42-/ZrO2-TiO2 solid acid catalyst calcined at different temperatures on its surface properties and catalytic activity were thoroughly investigated in this paper. The physicochemical characteristics of prepared samples were determined by N2 adsorptiondesorption, XRD, NH3-TPD and XPS techniques, respectively. It was found that the crystallization temperature of the samples increased after the combination of ZrO2 and TiO2; and phase transformations from the anatase to the rutile of TiO2 species and the tetragonal to the monoclinic of ZrO2 species were effectively suppressed at higher temperature. The sample with a Zr/Ti molar ratio of 3/1 calcined at 450℃ showed the highest surface area and the most acid sites among all the tested samples. The acid site densities of samples were relatively closed to each other if they were calcined at the same temperature, however, decreased with the calcination temperature. The result indicates that the sulfur content in samples is a crucial factor to control the acid site density. Calcining the sample at 650℃ and higher temperatures resulted in a significant desorption of sulfate ion on the samples. The synthesized samples were evaluated as a potential catalyst for glucose conversion under the near-critical methanol conditions （200℃/4 MPa）. The results suggested that the relatively weaker acid sites of the catalyst were more favorable for the accumulation of methyl glucosides, while the moderate acid sites were responsible for the formation of methyl levulinate. The catalytic activity for methyl levulinate production almost increases linearly with the catalyst acid site density. The catalyst deactivation is due to the loss of sulfate ion and the two catalysts with Zr/Ti molar ratios of 3/1 and 1/3 could effectively alleviate the deactivation caused by sulfate solution in the reaction medium and can be reused after calcination with the reuse rate of over 90% in terms of the methyl levulinate selectivity.

LPE Growth of InAsPSb on InAs:Melt Composition,Lattice Mismatch and Surface Morphology

The LPE growth of quaternary InAs11-x-yPxSby with x = 0.2 and y = 0.09 on InAs substrate has been studied. This composition is very suitable for the laser and detector applications at about 2.5 μm. We show that in InAsPSb/InAs system there is a determinate relation between the surface morphology and the lattice mismatch of the epi-wafers, by which we can easily control the melt composition to grow high quality hetero-structures. The reason has been discussed. The p-n junctions with fairly good carrier profile have been prepared in this system.

Correlation between the surface characteristics of carbon supports and their electrochemical stability and performance in fuel cell cathodes

In this paper,an extensive characterisation of a range of carbon blacks(CB)with similar surface area but different surface chemistry is carried out by flow calorimetry,Raman spectroscopy,dynamic water vapour sorption,instrumental gas analysis,nitrogen adsorption/desorption and high potential chronoamperometry.Using these carbon materials as supports,Pt/CB electrocatalysts are prepared by microwave-assisted polyol-mediated synthesis in gram scale.Structural,morphological and electrochemical properties of the prepared electrocatalysts are evaluated by X-ray diffraction,transmission electron microscopy,rotating disc electrode and in situ fuel cell characterisation of the corresponding membrane-electrode assemblies.The obtained results allow to establish a relationship between surface chemistry and electrochemical properties useful for the design of Pt/C catalyst layers with high performance and stability.