Soil-water characteristic surface model of soil-rock mixture

The relationship between the water content or saturation of unsaturated soils and its matrix suction is commonly described by the soilwater characteristic curve(SWCC).Currently,study on the SWCC model is focused on fine-grained soils like clay and silty soils,but the SWCC model for grinding soil-rock mixture(SRM)is less studied.Considering that the SRM is in a certain compaction state in the actual project,this study established a surface model with three variables of coupling compaction degree-substrate suction-moisture content based on the Cavalcante-Zornberg soil-water characteristic curve model.Then,the influence of each fitting parameter on the curve was analyzed.For the common SRM,the soil-water characteristic test was conducted.Moreover,the experimental measurements exhibit remarkable consistency with the mode surface.The analysis shows that the surface model intuitively describes the soil-water characteristics of grinding SRM,which can provide the SWCC of soils with bimodal pore characteristics under specific compaction degrees.Furthermore,it can reflect the influence of compaction degrees on the SWCC of rock-soil mass and has a certain prediction effect.The SWCC of SRM with various soil-rock ratios have a double-step shape.With the increase in compaction degree,the curves as a whole tend toward decreasing mass moisture content.The curve changes are mainly concentrated in the large pore section.

Impact of Spin-up Forcing on Vegetation States Simulated by a Dynamic Global Vegetation Model Coupled with a Land Surface Model

A dynamic global vegetation model （DGVM） coupled with a land surface model （LSM） is generally initialized using a spin-up process to derive a physically-consistent initial condition. Spin-up forcing, which is the atmospheric forcing used to drive the coupled model to equilibrium solutions in the spin-up process, varies across earlier studies. In the present study, the impact of the spin-up forcing in the initialization stage on the fractional coverages （FCs） of plant functional type （PFT） in the subsequent simulation stage are assessed in seven classic climate regions by a modified Community Land Model’s Dynamic Global Vegetation Model （CLM-DGVM）. Results show that the impact of spin-up forcing is considerable in all regions except the tropical rainforest climate region （TR） and the wet temperate climate region （WM）. In the tropical monsoon climate region （TM）, the TR and TM transition region （TR-TM）, the dry temperate climate region （DM）, the highland climate region （H）, and the boreal forest climate region （BF）, where FCs are affected by climate non-negligibly, the discrepancies in initial FCs, which represent long-term cumulative response of vegetation to different climate anomalies, are large. Moreover, the large discrepancies in initial FCs usually decay slowly because there are trees or shrubs in the five regions. The intrinsic growth timescales of FCs for tree PFTs and shrub PFTs are long, and the variation of FCs of tree PFTs or shrub PFTs can affect that of grass PFTs.

Improving the Vegetation Dynamic Simulation in a Land Surface Model by Using a Statistical-dynamic Canopy Interception Scheme

Canopy interception of incident precipitation, as a critical component of a forest＇s water budget, can affect the amount of water available to the soil, and ultimately vegetation distribution and function. In this paper, a statistical-dynamic approach based on leaf area index and statistical canopy interception is used to parameterize the canopy interception process. The statistical-dynamic canopy interception scheme is implemented into the Community Land Model with dynamic global vegetation model （CLM-DGVM） to improve its dynamic vegetation simulation. The simulation for continental China by the land surface model with the new canopy interception scheme shows that the new one reasonably represents the precipitation intercepted by the canopy. Moreover, the new scheme enhances the water availability in the root zone for vegetation growth, especially in the densely vegetated and semi-arid areas, and improves the model＇s performance of potential vegetation simulation.

A New Approach for Parameter Optimization in Land Surface Model

In this study,a new parameter optimization method was used to investigate the expansion of conditional nonlinear optimal perturbation （CNOP） in a land surface model （LSM） using long-term enhanced field observations at Tongyu station in Jilin Province,China,combined with a sophisticated LSM （common land model,CoLM）.Tongyu station is a reference site of the international Coordinated Energy and Water Cycle Observations Project （CEOP） that has studied semiarid regions that have undergone desertification,salination,and degradation since late 1960s.In this study,three key land-surface parameters,namely,soil color,proportion of sand or clay in soil,and leaf-area index were chosen as parameters to be optimized.Our study comprised three experiments：First,a single-parameter optimization was performed,while the second and third experiments performed triple-and six-parameter optimizations,respectively.Notable improvements in simulating sensible heat flux （SH）,latent heat flux （LH）,soil temperature （TS）,and moisture （MS） at shallow layers were achieved using the optimized parameters.The multiple-parameter optimization experiments performed better than the single-parameter experminent.All results demonstrate that the CNOP method can be used to optimize expanded parameters in an LSM.Moreover,clear mathematical meaning,simple design structure,and rapid computability give this method great potential for further application to parameter optimization in LSMs.

A new GIS-compatible methodology for visibility analysis in digital surface models of earth sites

As a GIS tool,visibility analysis is used in many areas to evaluate both visible and non-visible places.Visibility analysis builds on a digital surface model describing the terrain morphology,including the position and shapes of all objects that can sometimes act as visibility barriers.However,some barriers,for example vegetation,may be permeable to a certain degree.Despite extensive research and use of visibility analysis in different areas,standard GIS tools do not take permeability into account.This article presents a new method to calculate visibility through partly permeable obstacles.The method is based on a quasi-Monte Carlo simulation with 100 iterations of visibility calculation.Each iteration result represents 1%of vegetation permeability,which can thus range from 1%to 100%visibility behind vegetation obstacles.The main advantage of the method is greater accuracy of visibility results and easy implementation on any GIS software.The incorporation of the proposed method in GIS software would facilitate work in many fields,such as architecture,archaeology,radio communication,and the military.

Subdivision surface modeling system based on arbitrary topological curves network and combined subdivision

Arbitrary topological curve network has no restriction in topology structure,so it has more powerful representing ability in defining complex surfaces.A complex surface modeling system is presented based on arbitrary topological curve network and the improved combined subdivision method,its functions including creating and editing curve network,and generating and modifying curve network＇s interpolated surface.This modeling system can be used to the process of products＇concept design,and its applications is also significant to the development of subdivision method.

Numerical Simulation of Injection Molding Cooling Process Based on 3D Surface Model

The design of the cooling system of injection molds directly affects both productivity and the quality of the final part. Using the cooling process CAE system to instruct the mold design, the efficiency and quality of design can be improved greatly. At the same time, it is helpful to confirm the cooling system structure and optimize the process conditions. In this paper, the 3D surface model of mold cavity is used to replace the middle-plane model in the simulation by Boundary Element Method, which break the bottleneck of the application of the injection molding simulation softwares base on the middle-plane model. With the improvements of this paper, a practical and commercial simulation software of injection molding cooling process named as HsCAE3D6.0 is developed.

An Adaptive and Image-guided Fusion for Stereo Satellite Image Derived Digital Surface Models

The accuracy of Digital Surface Models(DSMs)generated using stereo matching methods varies due to the varying acquisition conditions and configuration parameters of stereo images.It has been a good practice to fuse these DSMs generated from various stereo pairs to achieve enhanced,in which multiple DSMs are combined through computational approaches into a single,more accurate,and complete DSM.However,accurately characterizing detailed objects and their boundaries still present a challenge since most boundary-ware fusion methods still struggle to achieve sharpened depth discontinuities due to the averaging effects of different DSMs.Therefore,we propose a simple and efficient adaptive image-guided DSM fusion method that applies k-means clustering on small patches of the orthophoto to guide the pixel-level fusion adapted to the most consistent and relevant elevation points.The experiment results show that our proposed method has outperformed comparing methods in accuracy and the ability to preserve sharpened depth edges.

An Effective Surface Modeling Method for Car Styling from a Side-View Image

We introduce an almost-automatic technique for generating 3D car styling surface models based on a single side-view image. Our approach combines the prior knowledge of car styling and deformable curve network model to obtain an automatic modeling process. Firstly, we define the consistent parameterized curve template for 2D and 3D case respectivelyby analyzingthe characteristic lines for car styling. Then, a semi-automatic extraction from a side-view car image is adopted. Thirdly, statistic morphable model of 3D curve network isused to get the initial solution with sparse point constraints.Withonly afew post-processing operations, the optimized curve network models for creating surfaces are obtained. Finally, the styling surfaces are automatically generated using template-based parametric surface modeling method. More than 50 3D curve network models are constructed as the morphable database. We show that this intelligent modeling toolsimplifiesthe exhausted modeling task, and also demonstratemeaningful results of our approach.

Using UAVs for detection of trees from digital surface models

A difficult problem in forestry is tree inventory.In this study, a GoProHero attached to a small unmanned aerial vehicle was used to capture images of a small area covered by pinus pinea trees. Then, a digital surface model was generated with image matching. The elevation model representing the terrain surface, a ‘digital terrain model’,was extracted from the digital surface model using morphological filtering. Individual trees were extracted by analyzing elevation flow on the digital elevation model because the elevation reached the highest value on the tree peaks compared to the neighborhood elevation pixels. The quality of the results was assessed by comparison with reference data for correctness of the estimated number of trees. The tree heights were calculated and evaluated with ground truth dataset. The results showed 80% correctness and 90% completeness.

Primary safe criterion of earth-brushing flight for flying vehicle over digital surface model

In modern terrain-following guidance it is an important index for flight vehicle to cruise about safely and normally. On the basis of a constructing method of digital surface model (DSM), the definition, classification and scale analysis of an isolated obstacle threatening flight safety of terrain-following guidance are made. When the interval of vertical-and cross-sections on DSM is 12. 5 m, the proportion of isolated obstacles to the data amount of DSM model to be loaded is optimal. The main factors influencing the lowest flying height in terrain-following guidance are analyzed, and a primary safe criterion of the lowest flying height over DSM model is proposed. According to their test errors, the lowest flying height over 1:10 000 DSM model can reach 40. 5 m^45. 0 m in terrain-following guidance. It is shown from the simulation results of a typical urban district that the proposed models and methods are reasonable and feasible.

A two scale nonlinear fractal sea surface model in a one dimensional deep sea

Using the theory of nonlinear interactions between long and short waves, a nonlinear fractal sea surface model is presented for a one dimensional deep sea. Numerical simulation results show that spectra intensity changes at different locations （in both the wave number domain and temporal-frequency domain）, and the system obeys the energy conservation principle. Finally, a method to limit the fractal parameters is also presented to ensure that the model system does not become ill-posed,

Continuities of Progressive and Mixing Algorithm for Surface Modeling and Editing

The progressive and mixing algorithm(PAMA) is a method for surface modeling and editing,which is developed for effective and flexible applications in many environments,such as computer-aided design(CAD) and computer-aided geometric design(CAGD).In this paper,the construction scheme and continuities of PAMA are discussed,which provide a mathematics analysis of PAMA.The analysis and results show that the PAMA provides a new method of surface modeling and editing with four more degrees of freedom for designers to manipulate a 3D object.

Surface Modelling and Mesh Generation for Simulating Superplastic Forming

This paper presents an approach which enables surface modelling, mesh generation and the Finite Element (FE) analysis to be integrated together to simulate superplastic forming process for complex shaped components. Techniques have been developed to generate an FE mesh over non-four-sided surface areas, the boundaries of which are Bezier curves of arbitrary degree, using a consistent expression. Theoretical evidence is given to determine the number of Bezier triangular patches required for accurately re-constructing die surfaces within a commercial FE solver. The developed techniques have been successfully used in determining the process parameters for forming a 3D rectangular box.

Improved shape hardening function for bounding surface model for cohesive soils

A shape hardening function is developed that improves the predictive capabilities of the generalized bounding surface model for cohesive soils, especially when applied to overconsolidated specimens. This improvement is realized without any changes to the simple elliptical shape of the bounding surface, and actually reduces the number of parameters associated with the model by one.

Elucidating Dominant Factors Affecting Land Surface Hydrological Simulations of the Community Land Model over China

In order to compare the impacts of the choice of land surface model(LSM)parameterization schemes,meteorological forcing,and land surface parameters on land surface hydrological simulations,and explore to what extent the quality can be improved,a series of experiments with different LSMs,forcing datasets,and parameter datasets concerning soil texture and land cover were conducted.Six simulations are run for the Chinese mainland on 0.1°×0.1°grids from 1979 to 2008,and the simulated monthly soil moisture(SM),evapotranspiration(ET),and snow depth(SD)are then compared and assessed against observations.The results show that the meteorological forcing is the most important factor governing output.Beyond that,SM seems to be also very sensitive to soil texture information;SD is also very sensitive to snow parameterization scheme in the LSM.The Community Land Model version 4.5(CLM4.5),driven by newly developed observation-based regional meteorological forcing and land surface parameters(referred to as CMFD_CLM4.5_NEW),significantly improved the simulations in most cases over the Chinese mainland and its eight basins.It increased the correlation coefficient values from 0.46 to 0.54 for the SM modeling and from 0.54 to 0.67 for the SD simulations,and it decreased the root-mean-square error(RMSE)from 0.093 to 0.085 for the SM simulation and reduced the normalized RMSE from 1.277 to 0.201 for the SD simulations.This study indicates that the offline LSM simulation using a refined LSM driven by newly developed observation-based regional meteorological forcing and land surface parameters can better model reginal land surface hydrological processes.

Spatial and temporal variations of gross primary production simulated by land surface model BCC_AVIM2.0

Gross primary production(GPP)is the largest flux and a crucial player in the terrestrial carbon cycle and has been studied extensively,yet large uncertainties remain in the spatiotemporal patterns of GPP in both observations and simulations.This study evaluates the performance of the second version of the Beijing Climate Center Atmosphere−Vegetation Interaction Model(BCC_AVIM2.0)in simulating GPP on multiple spatial and temporal scales in the Coupled Model Intercomparison Project Phase 6(CMIP6)experiments.Model simulations driven by two meteorological datasets were compared with two observation-based GPP products covering 1982–2008.Spatial patterns of annual GPP show a significant latitudinal gradient in each dataset,increasing from cold(tundra)and dry(desert)biomes to warm(temperate)and humid(tropical rainforest)biomes.BCC_AVIM2.0 overestimates GPP in most parts of the globe,especially in boreal forest regions and Southeast China,while underestimating GPP in subhumid regions in eastern South America and tropical Africa.The four datasets broadly agree on the GPP seasonal cycle,but BCC_AVIM2.0 predicts an earlier beginning of spring growth and a larger amplitude of seasonal variations than those in the observations.The observation-based datasets exhibit slight interannual variability(IAV)and weak GPP linear trends,while the BCC_AVIM2.0 simulations demonstrate relatively large year-to-year variability and significant trends in the low-latitudes and temperate monsoon regions in North America and East Asia.Regarding the possible relationships between annual means of GPP and climate factors,BCC_AVIM2.0 predicts more extensive regions of the globe where the IAV of annual GPP is dominated by precipitation,especially in mid-to-high latitudes of the Northern Hemisphere and tropical Africa,while the observed GPP in the above regions is temperature-or radiation-dominant.The positive GPP biases due to earlier spring growth in boreal forest regions and negative GPP biases in off-equator tropical areas in the BCC_AVIM2.0 simulations imply that cold stress on biomes in boreal mid-to-high latitudes should be strengthened to restrain plant growth,while drought stress in low-latitude regions might be eased to enhance plant production in the future version of BCC_AVIM.

VOC emission caps constrained by air quality targets based on response surface model:A case study in the Pearl River Delta Region,China

Because of the recent growth in ground-level ozone and increased emission of volatile organic compounds(VOCs),VOC emission control has become a major concern in China.In response,emission caps to control VOC have been stipulated in recent policies,but few of them were constrained by the co-control target of PM_(2.5)and ozone,and discussed the factor that influence the emission cap formulation.Herein,we proposed a framework for quantification of VOC emission caps constrained by targets for PM_(2.5)and ozone via a new response surface modeling(RSM)technique,achieving 50%computational cost savings of the quantification.In the Pearl River Delta(PRD)region,the VOC emission caps constrained by air quality targets varied greatly with the NOxemission reduction level.If control measures in the surrounding areas of the PRD region were not considered,there could be two feasible strategies for VOC emission caps to meet air quality targets(160μg/m^(3)for the maximum 8-hr-average 90th-percentile(MDA8-90%)ozone and 25μg/m^(3)for the annual average of PM_(2.5)):a moderate VOC emission cap with<20%NOxemission reductions or a notable VOC emission cap with>60%NOxemission reductions.If the ozone concentration target were reduced to 155μg/m^(3),deep NOxemission reductions is the only feasible ozone control measure in PRD.Optimization of seasonal VOC emission caps based on the Monte Carlo simulation could allow us to gain higher ozone benefits or greater VOC emission reductions.If VOC emissions were further reduced in autumn,MDA8-90%ozone could be lowered by 0.3-1.5μg/m^(3),equaling the ozone benefits of 10%VOC emission reduction measures.The method for VOC emission cap quantification and optimization proposed in this study could provide scientific guidance for coordinated control of regional PM_(2.5)and O_(3)pollution in China.

Modeling of multiphase flow in low permeability porous media:Effect of wettability and pore structure properties

Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.

An accurate analytical surface potential model of heterojunction tunnel FET

Based on the accurate and efficient thermal injection method, we develop a fully analytical surface potential model for the heterojunction tunnel field-effect transistor(H-TFET). This model accounts for both the effects of source depletion and inversion charge, which are the key factors influencing the charge, capacitance and current in H-TFET. The accuracy of the model is validated against TCAD simulation and is greatly improved in comparison with the conventional model based on Maxwell–Boltzmann approximation. Furthermore, the dependences of the surface potential and electric field on biases are well predicted and thoroughly analyzed.