A beam steering effect of high-power quantum cascade(QC) lasers emitting at 4.6 μm was investigated. The continuous wave(CW) output power of an uncoated, 6-mm-long, 7.5-μm-wide buried-heterostructure QC laser at 25...A beam steering effect of high-power quantum cascade(QC) lasers emitting at 4.6 μm was investigated. The continuous wave(CW) output power of an uncoated, 6-mm-long, 7.5-μm-wide buried-heterostructure QC laser at 25℃ was as high as 854.2 m W. The maximum beam steering angle was offset by ±14.2° from the facet normal(0°) in pulsed mode. The phenomenon was judged explicitly by combining the diffraction limit theory and Fourier transform of the spectra. It was also verified by finite element method software simulation and the calculation of two-dimensional(2 D)effective-index model. The observed steering is consistent with a theory for coherence between the two lowest order lateral modes. Therefore, we have established an intrinsic linkage between the spectral instabilities and the beam steering by using the Fourier transform of the spectra, and further presented an extremely valid method to judge the beam steering. The content of this method includes both three equidistant peak positions in the Fourier transform of the spectra and the beam quality located between once the diffraction limit(DL) and twice the DL.展开更多
Beam steering in implant defined coherently coupled vertical cavity surface emitting laser （VCSEL） arrays is simulated using the FDTD solution software. Angular deflection dependent on relative phase differences amo...Beam steering in implant defined coherently coupled vertical cavity surface emitting laser （VCSEL） arrays is simulated using the FDTD solution software. Angular deflection dependent on relative phase differences among elements, inter-element spacing, element size and emitted wavelength is analyzed detailedly and systematically. We design and fabricate 1×2 implant defined VCSEL arrays for optimum beam steering performance. Electroni- cally controlled beam steering with a maximum deflection angle of 1.6° is successfully achieved in the 1 × 2 VCSEL arrays. The percentage of the power in the central lobe is above 39% when steering. The results show that the steering is controllable. Compared with other beam steering methods, the fabrication process is simple and of low cost.展开更多
This paper presents initial development of polymer application. PNC materials containing a polyamide （PA） and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites （PNC） material for rap...This paper presents initial development of polymer application. PNC materials containing a polyamide （PA） and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites （PNC） material for rapid manufacturing （RM） particles （5 wt%） were produced by solution blending with the aim （PA6） was dissolved in formic acid （HCO2H） together with two different types of nano particle materials： yttrium stabilised zirconia （YSZ） and Hectorite clay （Benton 166） and spray-dried to create powder, creating powder with particle sizes in the range of 10-40 μm. The materials were processed on a CO2 selective laser sintering （SLS） experimental machine. Mechanical properties of the PNCs were evaluated and the results were compared with the unfilled base polymer. Good dispersion of additives was achieved by solution blending, however the PA6 was degraded during the material preparation and spray drying process which resulted in the formation of porous structure and low strength. However the addition of 5 （wt%） nano particles in the PA6 has shown to increase strength by an average of 50-60%. Further work on powder preparation is required in order to fully realize these performance benefits.展开更多
基金Project supported by the National Basic Research Program of China(Grant Nos.2018YFA0209103 and 2018YFB2200504)the National Natural Science Foundation of China(Grant Nos.61991430,61774146,61790583,61674144,and 61774150)the Key Projects of the Chinese Academy of Sciences(Grant Nos.2018147,YJKYYQ20190002,QYZDJ-SSW-JSC027,and XDB43000000).
文摘A beam steering effect of high-power quantum cascade(QC) lasers emitting at 4.6 μm was investigated. The continuous wave(CW) output power of an uncoated, 6-mm-long, 7.5-μm-wide buried-heterostructure QC laser at 25℃ was as high as 854.2 m W. The maximum beam steering angle was offset by ±14.2° from the facet normal(0°) in pulsed mode. The phenomenon was judged explicitly by combining the diffraction limit theory and Fourier transform of the spectra. It was also verified by finite element method software simulation and the calculation of two-dimensional(2 D)effective-index model. The observed steering is consistent with a theory for coherence between the two lowest order lateral modes. Therefore, we have established an intrinsic linkage between the spectral instabilities and the beam steering by using the Fourier transform of the spectra, and further presented an extremely valid method to judge the beam steering. The content of this method includes both three equidistant peak positions in the Fourier transform of the spectra and the beam quality located between once the diffraction limit(DL) and twice the DL.
基金Supported by the‘Supporting First Action’Joint Foundation for Outstanding Postdoctoral Program under Grant Nos Y7YBSH0001 and Y7BSH14001the National Natural Science Foundation of China under Grant No 61434006the National Key Basic Research Program of China under Grant No 2017YFB0102302
文摘Beam steering in implant defined coherently coupled vertical cavity surface emitting laser （VCSEL） arrays is simulated using the FDTD solution software. Angular deflection dependent on relative phase differences among elements, inter-element spacing, element size and emitted wavelength is analyzed detailedly and systematically. We design and fabricate 1×2 implant defined VCSEL arrays for optimum beam steering performance. Electroni- cally controlled beam steering with a maximum deflection angle of 1.6° is successfully achieved in the 1 × 2 VCSEL arrays. The percentage of the power in the central lobe is above 39% when steering. The results show that the steering is controllable. Compared with other beam steering methods, the fabrication process is simple and of low cost.
文摘This paper presents initial development of polymer application. PNC materials containing a polyamide （PA） and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites （PNC） material for rapid manufacturing （RM） particles （5 wt%） were produced by solution blending with the aim （PA6） was dissolved in formic acid （HCO2H） together with two different types of nano particle materials： yttrium stabilised zirconia （YSZ） and Hectorite clay （Benton 166） and spray-dried to create powder, creating powder with particle sizes in the range of 10-40 μm. The materials were processed on a CO2 selective laser sintering （SLS） experimental machine. Mechanical properties of the PNCs were evaluated and the results were compared with the unfilled base polymer. Good dispersion of additives was achieved by solution blending, however the PA6 was degraded during the material preparation and spray drying process which resulted in the formation of porous structure and low strength. However the addition of 5 （wt%） nano particles in the PA6 has shown to increase strength by an average of 50-60%. Further work on powder preparation is required in order to fully realize these performance benefits.
