In recent years,scientists have become increasingly concerned in recycling electronic trash,particularly waste printed circuit boards(WPCBs).Previous research has indicated that the presence of Cu impacts the pyrolysi...In recent years,scientists have become increasingly concerned in recycling electronic trash,particularly waste printed circuit boards(WPCBs).Previous research has indicated that the presence of Cu impacts the pyrolysis of WPCBs.However,there may be errors in the experimental results,as printed circuit boards(PCBs)with copper and those without copper are produced differently.For this experiment,we blended copper powder with PCB nonmetallic resin powder in various ratios to create the samples.The apparent kinetics and pyrolysis properties of four resin powders with varying copper concentrations were compared using nonisothermal thermogravimetric analysis(TG)and thermal pyrolysis-gas chromatography mass spectrometry(Py-GC/MS).From the perspective of kinetics,the apparent activation energy of the resin powder in the pyrolysis reaction shows a rise(0.1<a<0.2)-stable(0.2<a<0.4)-accelerated increase(0.4<a<0.8)-decrease(0.8<a<0.9)process.After adding copper powder,the apparent activation energy changes more obviously when(0.2<a<0.4).In the early stage of the pyrolysis reaction(0.1<a<0.6),the apparent activation energy is reduced,but when a?0.8,it is much higher than that of the resin sample without copper.Additionally,it is discovered using thermogravimetric analysis and Py-GC/MS that copper shortens the temperature range of the primary pyrolysis reaction and prevents the creation of compounds containing bromine.This inhibition will raise the temperature at which compounds containing bromine first form,and it will keep rising as the copper level rises.The majority of the circuit board molecules have lower bond energies when copper is present,according to calculations performed using the Gaussian09 software,which promotes the pyrolysis reaction.展开更多
Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate...Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.展开更多
The Milan Gobi area of the Golmud-Korla Railway in northwest China is located in the lower dispersal area of the mountain pass and has strong winds with evident double wind direction characteristics.This study introdu...The Milan Gobi area of the Golmud-Korla Railway in northwest China is located in the lower dispersal area of the mountain pass and has strong winds with evident double wind direction characteristics.This study introduced a novel sand fence deployment technique,termed‘folded linear deployment',designed to position the sand fence orthogonally to the two predominant wind directions for optimal protection.This study used wind tunnel and field tests to evaluate the wind and sand flow characteristics,as well as the windproof and sandresistant performance of folded linear HDPE(Highdensity polyethylene)board sand fences.The results suggest that the airflow around the fence creates clear zoning characteristics.The deceleration area on the BSF(backwind side of the sand fence)is much larger than that on the DSF(downwind side of the sand fence).Thus,sand particles are primarily deposited on the BSF.At different wind speeds,the airflow at 2 and 5 h on the DSF is not disturbed.The WSP(wind speed profile)presents a logarithmic distribution.The airflow is disturbed at 1-20 h on the BSF,and the WSP gradually deviates from the logarithmic law.However,as the airflow moves away from the fence,the WSP gradually approaches a logarithmic distribution.Meanwhile,the WPE(windproof efficiency)and SRE(sand-resistant efficiency)of the sand fence exceed 80%.In addition,the results of wind tunnel tests are compared with those of field tests.The overall dispersion is good,and the best dispersion is found at z/H=2.00,indicating good agreement between the two test results.This study provides a scientific basis for the design of sand hazard control measures,similar to the railway project in the Gobi Gale area.展开更多
The Golmud-Korla Railway in the Gobi area faces operational challenges due to sand hazards,caused by strong and variable winds.This study addresses these challenges by conducting wind tunnel tests to evaluate the prot...The Golmud-Korla Railway in the Gobi area faces operational challenges due to sand hazards,caused by strong and variable winds.This study addresses these challenges by conducting wind tunnel tests to evaluate the protective benefits of High Density Polyethylene(HDPE)board sand fences,focusing on their orientation relative to various wind directions(referred to as'wind angle').This study found that the size of the low-velocity zone on the leeward side of the sand fences(LSF)expanded with an increase in the wind angle(WA).At 1H(the height of the sand fence)and 2H positions on the LSF,the wind speed profiles(WSP)exhibited a segmented logarithmic growth,constrained by Z=H at varying WAs.The efficacy of the sand fence in obstructing airflow escalated as WA increased.The size of the WA has a significant impact on the protective efficiency of HDPE board sand fences.Furthermore,compared to typical sandy surfaces,the rate of sand transport across the Gobi surface diminishes more slowly with height,attributed to the gravel's rebound effect.This phenomenon allows some sand particles to bypass the fences,rendering them less effective at blocking wind and trapping sand than in sandy environments.This paper offers scientific evidence supporting the practical use and enhancement of HDPE board sand fences in varied wind conditions.展开更多
This research aims to measure the current gender representation in membership of boards of directors,and to study the factors affecting the presence of women on boards.The results of the study will support the decisio...This research aims to measure the current gender representation in membership of boards of directors,and to study the factors affecting the presence of women on boards.The results of the study will support the decision makers and policy makers at all levels by providing knowledge that contributes to bridging the current gap in participation of women boards.The methodology used in this research is the descriptive analytical approach,which relies on quantitative methods in the process of collecting and analyzing data.This study represents the boards of directors in the three sectors(public,private,and non-profit)in the Kingdom of Saudi Arabia,The study sample contained 350 targets,where a random sample of 150 people in the public sector,100 people in the private sector,and 100 people in the non-profit sector were selected.The research result found that the majority of the responses believe that the lack of experience and training,and social factors,are the most impact areas of explaining the reasons for the existence of a gap in women’s membership in boards of directors in the three sectors.And the most important reasons for the existence of a gender gap in board membership are:there is no statutory minimum percentage for women’s representation on boards of directors,and scarcity of female competencies in general,and the lack of women occupying leadership positions.展开更多
This study tackles current environmental challenges by developing innovative and eco-friendly particle boards utilizing sorghum husk, combined with recycled expanded polystyrene (EPS). This dual eco-responsible approa...This study tackles current environmental challenges by developing innovative and eco-friendly particle boards utilizing sorghum husk, combined with recycled expanded polystyrene (EPS). This dual eco-responsible approach valorizes sorghum husk, often deemed agricultural waste, and repurposes EPS, a plastic waste, thus contributing to CO2 emission reduction and effective waste management. The manufacturing process involves dissolving recycled polystyrene within a solvent to create a binder, which is then mixed with sorghum husk and cold-pressed into composite boards. The study explores the impact of two particle sizes (fine and coarse) and two different concentrations of the recycled EPS binder. Results demonstrate significant variations in the boards’ mechanical properties, displaying a range of Modulus of Rupture (MOR) from 0.84 MPa to 3.85 MPa, and Modulus of Elasticity (MOE) spanning from 658.13 MPa to 1313.25 MPa, influenced by the binder concentration and particle size. These characteristics suggest that the boards can be effectively used in various construction applications, including interior decoration, false ceilings, and potentially for furniture and door manufacturing when combined with appropriate coatings. This study not only exemplifies the valorization of plastic and agricultural wastes but also offers a practical, localized solution to global climate change challenges by promoting sustainable construction materials.展开更多
The existing systems sustained with the investments made require more automation and digital transformation with the continuous advancement of tech-nology.The aviation industry is a sector that is open to more automat...The existing systems sustained with the investments made require more automation and digital transformation with the continuous advancement of tech-nology.The aviation industry is a sector that is open to more automation and digi-tal transformation,mainly because of the intense competition and the analysis of a large variety of data.The long duration of operations in current airline processes and some processflows cause customer dissatisfaction and cost increase.In this study,the boarding process,which is one of the operational processes of airline transportation and is open to improvement,was discussed.The classical boarding process has been redesigned using Internet of Things technology a model called Boarding 4.0 was created.With Boarding 4.0,it is aimed to design a process where passengers can take their time before boarding more efficiently.In the study,the sub-processes of the Boarding 4.0 model,other processes that the sub-processes interact with,their activities,and data exchange passenger move-ments during the activities are explained in detail.Compared to the classical boarding process and Boarding 4.0 with the fuzzy ahp technique,it has been shown that boarding 4.0 is more advantageous and passenger movement times can be reduced during boarding.As a result of the evaluation made with the fuzzy ahp,it was determined that boarding 4.0 is more advantageous than the classical boarding process.In addition,when the total time of the sub-activities in the board-ing process is calculated,boarding activities for a passenger take 50 min with the classic boarding process and 20 min with Boarding 4.0.Thus,when Boarding 4.0 is used,the passenger gains 30 min.Furthermore,when the calculation is made concerning the airport’s current capacity,two passengers are hosted with the clas-sical boarding process,whilefive passengers are hosted with Boarding 4.0.This acquisition is significant for airports in terms of efficient use of resources.展开更多
Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,...Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,polystyrene granule mortar and polyurethane foam in order to study the weatherablility of external thermal insulation system(ETIS).The change rules of adhesive strength were hereby studied at different time period of atmospheric exposure tests.The experimental results show that the adhesive strength of three kinds of ETIS changes a little during high temperature-spraying water cycle,but the adhesive strength of ETIS with EPS board decreases significantly after heating-refrigeration cycle.The lowering rate of adhesive strength with painting finishes is obviously faster than that of tile finishes for ETIS of EPS board during heating-refrigeration cycle.The weatherability of ETIS with EPS board is worse than the other two,and ETIS of polystyrene granule mortar and polyurethane foam are more suitable than ETIS of EPS board in cold area.展开更多
The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and c...The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and compared with experimental results to verify the reliability of the numerical simulation method.Accordingly,the concept of splitter structural coefficients was proposed.Based on the results of this study,we recommend a selection range of 5≤k≤6 for the structure factor k of the splitter;after optimization,the maximum deviation of the splitter outlet flow was reduced from the original value of 100%to 8.3%.展开更多
In this paper, we conduct research on the pragmatics of politeness principle of bulletin board system based on the differences of gender and habits. The openness of the Internet makes all kinds of information received...In this paper, we conduct research on the pragmatics of politeness principle of bulletin board system based on the differences of gender and habits. The openness of the Internet makes all kinds of information received into the vision of an equal chance and web sites in order to improve the hit rate which causes the traffic of commercial purposes such as tabloidization tend to be more negative news spread. To strengthen the research of network language management strategy, it has very important theoretical significance and practical meaning analyzed. Our proposed methodology will help researchers to understand the approaches to use the pragrnatics of politeness.展开更多
Automated optical inspection(AOI)is a significant process in printed circuit board assembly(PCBA)production lines which aims to detect tiny defects in PCBAs.Existing AOI equipment has several deficiencies including lo...Automated optical inspection(AOI)is a significant process in printed circuit board assembly(PCBA)production lines which aims to detect tiny defects in PCBAs.Existing AOI equipment has several deficiencies including low throughput,large computation cost,high latency,and poor flexibility,which limits the efficiency of online PCBA inspection.In this paper,a novel PCBA defect detection method based on a lightweight deep convolution neural network is proposed.In this method,the semantic segmentation model is combined with a rule-based defect recognition algorithm to build up a defect detection frame-work.To improve the performance of the model,extensive real PCBA images are collected from production lines as datasets.Some optimization methods have been applied in the model according to production demand and enable integration in lightweight computing devices.Experiment results show that the production line using our method realizes a throughput more than three times higher than traditional methods.Our method can be integrated into a lightweight inference system and pro-mote the flexibility of AOI.The proposed method builds up a general paradigm and excellent example for model design and optimization oriented towards industrial requirements.展开更多
Five types of polyurea elastomers were synthesized by changing the isocyanate component and the mechanical properties of polyurea materials were measured. Fiber-reinforced cement boards(FRCB)strengthened by polyurea w...Five types of polyurea elastomers were synthesized by changing the isocyanate component and the mechanical properties of polyurea materials were measured. Fiber-reinforced cement boards(FRCB)strengthened by polyurea with different formulations were processed, and a series of experiments were carried out on the specimens with gas explosion devices. The results showed that the conventional mechanical properties of different types of polyureas had their own advantages. Based on the gas explosion overpressure criterion, the blast resistances of reinforced plates were quantitatively evaluated,and the best polyurea was selected to guide the formulation design. The three typical failure modes of polyurea-reinforced FRCBs were flexural, shear, and flexural-shear failure. Dynamic thermodynamics and shock wave spectral analysis revealed that the polyurea did not undergo a glass transition in the gas explosion tests but retained its elastic properties, allowing it to effectively wrap the fragments formed by the brittle substrates.展开更多
The present analytical review is devoted to the current problem of thermodynamic stability and related thermodynamic characteristics of the following graphene layers systems: 1) double-side hydrogenated graphene of co...The present analytical review is devoted to the current problem of thermodynamic stability and related thermodynamic characteristics of the following graphene layers systems: 1) double-side hydrogenated graphene of composition CH (theoretical graphane) (Sofo et al. 2007) and experimental graphane (Elias et al. 2009);2) theoretical single-side hydrogenated graphene of composition CH;3) theoretical single-side hydrogenated graphene of composition C2H (graphone);4) experimental hydrogenated epitaxial graphene, bilayer graphene and a few layers of graphene on SiO2 or other substrates;5) experimental and theoretical single-external side hydrogenated single-walled carbon nanotubes, and experimental hydrofullerene C60H36;6) experimental single-internal side hydrogenated (up to C2H or CH composition) graphene nanoblisters with intercalated high pressure H2 gas inside them, formed on a surface of highly oriented pyrolytic graphite or epitaxial graphene under the atomic hydrogen treatment;and 7) experimental hydrogenated graphite nanofibers-multigraphene with intercalated solid H2 nano-regions of high density inside them, relevant to solving the problem of hydrogen on-board storage (Nechaev 2011-2012).展开更多
Starting from the corrosion mechanism,this paper analyzes the characteristics of various types of stainless steel and selects the best performance composite plate composite plate stainless steel.Analyze and select the...Starting from the corrosion mechanism,this paper analyzes the characteristics of various types of stainless steel and selects the best performance composite plate composite plate stainless steel.Analyze and select the most suitable corrosion detection method based on specific practical multi working conditions,discuss the interference factors that affect metal corrosion during experimental simulation,and the advantages of newly developed sheet metal.The new development of composite board panels,with the substrate and composite materials applying their respective capabilities for MED,will bring breakthrough progress to the scientific research and engineering applica-tion of composite boards.展开更多
For Printed Circuit Board(PCB)surface defect detection,traditional detection methods mostly focus on template matching-based reference method and manual detections,which have the disadvantages of low defect detection ...For Printed Circuit Board(PCB)surface defect detection,traditional detection methods mostly focus on template matching-based reference method and manual detections,which have the disadvantages of low defect detection efficiency,large errors in defect identification and localization,and low versatility of detectionmethods.In order to furthermeet the requirements of high detection accuracy,real-time and interactivity required by the PCB industry in actual production life.In the current work,we improve the Youonly-look-once(YOLOv4)defect detection method to train and detect six types of PCB small target defects.Firstly,the original Cross Stage Partial Darknet53(CSPDarknet53)backbone network is preserved for PCB defect feature information extraction,and secondly,the original multi-layer cascade fusion method is changed to a single-layer feature layer structure to greatly avoid the problem of uneven distribution of priori anchor boxes size in PCB defect detection process.Then,the K-means++clustering method is used to accurately cluster the anchor boxes to obtain the required size requirements for the defect detection,which further improves the recognition and localization of small PCB defects.Finally,the improved YOLOv4 defect detection model is compared and analyzed on PCB dataset with multi-class algorithms.The experimental results show that the average detection accuracy value of the improved defect detection model reaches 99.34%,which has better detection capability,lower leakage rate and false detection rate for PCB defects in comparison with similar defect detection algorithms.展开更多
We introduce evolutionary game method to analyze low-price collusion in inquiry market of Sci-Tech Innovation Board of China(SIBC)from the perspective of strategic interaction between large institutional investors(LII...We introduce evolutionary game method to analyze low-price collusion in inquiry market of Sci-Tech Innovation Board of China(SIBC)from the perspective of strategic interaction between large institutional investors(LIIs),small and medium-sized institutional investors(SMIIs),and supervision department(SD).The results show that supervision behaviors of SD,and quotation behaviors of institutional investors,are subject to supervision conditions.Under the condition that benefits of tough supervision are lower a lot than minimum benefits of light supervision(light supervision condition),SD will choose light supervision and institutional investors will turn to illegal quotation in response.Finally,a steady-state equilibrium with low-price collusion will form in SIBC’s inquiry market even with a large supervision penalty for illegal quotation.On the contrary,under the condition that benefits of tough supervision are higher a lot than maximum benefits of light supervision(tough supervision condition)and with a large penalty for illegal quotation,SD and institutional investors will choose tough supervision and legal quotation.Further numerical simulations under light supervision condition show that:(1)High-price culling rule will become a booster for low-price collusion and accelerate SMIIs’evolutionary process to imitative quotation.(2)Blindly increasing penalties for illegal quotation or reducing the culling rate is not an appropriate approach to solve the problem of low-price collusion since it cannot shift supervision condition from light into tough and make SD supervise toughly.(3)Institutional investors’choices of quotation strategies are more volatile and highly susceptible to supervision behaviors of SD when facing exogenous uncertainty.Therefore,the keys to solving the problem of low-price collusion are shifting supervision condition from light into tough through increasing incremental benefits of tough supervision,and providing institutional investors with a stable and predictable supervision policy.In conclusion,the creation of a fair inquiry market doesn’t only depend on restraint and punishment to institutional investors,but also requires the establishment of supervision mechanism those are compatible with market-based inquiry.展开更多
The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole process...The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole processing.The problem of optimal control of its drilling force is one of the main factors affecting the quality of micro-hole machining.To address this problem,the thrust forces and torques in PCB drilling were first modeled and analyzed,and the corresponding prediction models were established.The drilling force analysis was carried out through the micro-hole drilling experiment,the specific cutting energy under different feed rates was calculated,the influence of the size effect was clarified,and the accuracy of the prediction model was verified.The result shows that during the drilling of glass fiber cloth,changes in the material removal mechanism are induced as the feed per revolution is varied.When the feed per revolution is less than the tool edge radius,the glass fiber is not cut by the main cutting edge,but is crushed and broken.When the feed per revolution is greater than the radius of the tool edge,the glass fiber is cut by the main cutting edge.At the same time,the established analytical model can accurately reflect the influence of the size effect on the drilling torque in PCB micro-hole drilling,and the error is within 10%.This method has certain practical application value in controlling PCB micro hole processing quality.展开更多
On the basis of on-site measured data of the newly constructed Gonghe-Yushu Highway in a permafrost region, this paper analyzed thermal conditions of the subgrade with XPS insulated board according to different select...On the basis of on-site measured data of the newly constructed Gonghe-Yushu Highway in a permafrost region, this paper analyzed thermal conditions of the subgrade with XPS insulated board according to different selected monitoring sections in various locations. We also summarized the geothermal distribution and change rules of subgrade with XPS insulation board under the asphalt pavement in summarized a high temperature frozen soil region. It is suggested that the shoulder of subgrade with XPS insulation board be widen to a reasonable width so as to keep the subgrade stable.展开更多
Density and resin content are two factors that have a significant effect on the production cost of wood composite. However, particle size affects resin content and density, which suggests that the interaction of these...Density and resin content are two factors that have a significant effect on the production cost of wood composite. However, particle size affects resin content and density, which suggests that the interaction of these three factors can be manipulated to reduce the board density and resin content of particleboard without adversely influencing its mechanical properties. Some mathematical functional forms based on resin content, board density and slenderness ratio were regressed and an appropriate form was chosen. According to analysis of the results using SHAZAM 9 software, the exponential function best fit the experimental data. Finally, "indifference curves" of mechanical properties were illustrated and analyzed. The results indicated that negative effects of density or resin content reduction on mechanical properties could be compensated for by controlling particles' slenderness ratio. Interestingly, increases in slenderness ratio compensated for the negative effects of decreases in resin content or board density on module of rupture (MOR) and module of elasticity (MOE). Moreover, this "compensation ratio" intensified as resin content or density decreased and/or as the MOR or MOE increased. On the other hand, reduction in slenderness ratio indicated a comple- mentary effect on reducing internal bond (IB) strength, a result of decreases in resin content or density. Moreover, this "complementary ratio" was intensified as resin content or density decreased and/or as IB strength increased.展开更多
In this paper, we tested the hydrodynamic characteristics of a new, double-winged otter board that consists of a forewing, a leading edge slat and a trailing edge flap. Flume experiments were conducted in a circulatin...In this paper, we tested the hydrodynamic characteristics of a new, double-winged otter board that consists of a forewing, a leading edge slat and a trailing edge flap. Flume experiments were conducted in a circulating flume tank by using a model with an aspect ratio(AR) of 0.85 and a horizontal planform area( S) of 0.09 m^2. The results indicated that the critical angle( α_(cr)) of the model was 44°, whereas the maximum lift coefficient( C_(Lmax)) was up to 1.715, and the door efficiency( K) was 1.122. The attack angle( α) ranged from 30° to 48° and from 10° to 46° when the lift coefficient( C_L) and door efficiency( K) were greater than 1.2 and 1.0, respectively. To compare the difference between double-winged otter board and traditional Morgere Polyvalent Ovale, same model of Morgere Polyvalent Ovale was also tested under the same experimental conditions. The critical angle( α_(cr)) and maximum of lift coefficient( C_(Lmax)) of the doublewinged otter board were 37.5% and 14.6% larger than those of the Morgere Polyvalent Ovale. Therefore, we concluded that the novel, double-winged otter board was more suitable for bottom trawling fisheries in the deep water of the Mauretania Sea due to its better hydrodynamic characteristics and stability.展开更多
基金supported by the National Key Research and Development Program of China(2018YFC1902504).
文摘In recent years,scientists have become increasingly concerned in recycling electronic trash,particularly waste printed circuit boards(WPCBs).Previous research has indicated that the presence of Cu impacts the pyrolysis of WPCBs.However,there may be errors in the experimental results,as printed circuit boards(PCBs)with copper and those without copper are produced differently.For this experiment,we blended copper powder with PCB nonmetallic resin powder in various ratios to create the samples.The apparent kinetics and pyrolysis properties of four resin powders with varying copper concentrations were compared using nonisothermal thermogravimetric analysis(TG)and thermal pyrolysis-gas chromatography mass spectrometry(Py-GC/MS).From the perspective of kinetics,the apparent activation energy of the resin powder in the pyrolysis reaction shows a rise(0.1<a<0.2)-stable(0.2<a<0.4)-accelerated increase(0.4<a<0.8)-decrease(0.8<a<0.9)process.After adding copper powder,the apparent activation energy changes more obviously when(0.2<a<0.4).In the early stage of the pyrolysis reaction(0.1<a<0.6),the apparent activation energy is reduced,but when a?0.8,it is much higher than that of the resin sample without copper.Additionally,it is discovered using thermogravimetric analysis and Py-GC/MS that copper shortens the temperature range of the primary pyrolysis reaction and prevents the creation of compounds containing bromine.This inhibition will raise the temperature at which compounds containing bromine first form,and it will keep rising as the copper level rises.The majority of the circuit board molecules have lower bond energies when copper is present,according to calculations performed using the Gaussian09 software,which promotes the pyrolysis reaction.
文摘Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.
基金financially supported by the Chang Jiang Scholar and Innovation Team Development Plan of China(IRT_15R29)the Basic Research Innovation Group Project of Gansu Province,China(21JR7RA347)the Natural Science Foundation of Gansu Province,China(20JR10RA231)。
文摘The Milan Gobi area of the Golmud-Korla Railway in northwest China is located in the lower dispersal area of the mountain pass and has strong winds with evident double wind direction characteristics.This study introduced a novel sand fence deployment technique,termed‘folded linear deployment',designed to position the sand fence orthogonally to the two predominant wind directions for optimal protection.This study used wind tunnel and field tests to evaluate the wind and sand flow characteristics,as well as the windproof and sandresistant performance of folded linear HDPE(Highdensity polyethylene)board sand fences.The results suggest that the airflow around the fence creates clear zoning characteristics.The deceleration area on the BSF(backwind side of the sand fence)is much larger than that on the DSF(downwind side of the sand fence).Thus,sand particles are primarily deposited on the BSF.At different wind speeds,the airflow at 2 and 5 h on the DSF is not disturbed.The WSP(wind speed profile)presents a logarithmic distribution.The airflow is disturbed at 1-20 h on the BSF,and the WSP gradually deviates from the logarithmic law.However,as the airflow moves away from the fence,the WSP gradually approaches a logarithmic distribution.Meanwhile,the WPE(windproof efficiency)and SRE(sand-resistant efficiency)of the sand fence exceed 80%.In addition,the results of wind tunnel tests are compared with those of field tests.The overall dispersion is good,and the best dispersion is found at z/H=2.00,indicating good agreement between the two test results.This study provides a scientific basis for the design of sand hazard control measures,similar to the railway project in the Gobi Gale area.
基金financially supported by the National Natural Science Foundation of China (42461011, 42071014)the Fellowship of the China Postdoctoral Science Foundation (2021M703466)
文摘The Golmud-Korla Railway in the Gobi area faces operational challenges due to sand hazards,caused by strong and variable winds.This study addresses these challenges by conducting wind tunnel tests to evaluate the protective benefits of High Density Polyethylene(HDPE)board sand fences,focusing on their orientation relative to various wind directions(referred to as'wind angle').This study found that the size of the low-velocity zone on the leeward side of the sand fences(LSF)expanded with an increase in the wind angle(WA).At 1H(the height of the sand fence)and 2H positions on the LSF,the wind speed profiles(WSP)exhibited a segmented logarithmic growth,constrained by Z=H at varying WAs.The efficacy of the sand fence in obstructing airflow escalated as WA increased.The size of the WA has a significant impact on the protective efficiency of HDPE board sand fences.Furthermore,compared to typical sandy surfaces,the rate of sand transport across the Gobi surface diminishes more slowly with height,attributed to the gravel's rebound effect.This phenomenon allows some sand particles to bypass the fences,rendering them less effective at blocking wind and trapping sand than in sandy environments.This paper offers scientific evidence supporting the practical use and enhancement of HDPE board sand fences in varied wind conditions.
文摘This research aims to measure the current gender representation in membership of boards of directors,and to study the factors affecting the presence of women on boards.The results of the study will support the decision makers and policy makers at all levels by providing knowledge that contributes to bridging the current gap in participation of women boards.The methodology used in this research is the descriptive analytical approach,which relies on quantitative methods in the process of collecting and analyzing data.This study represents the boards of directors in the three sectors(public,private,and non-profit)in the Kingdom of Saudi Arabia,The study sample contained 350 targets,where a random sample of 150 people in the public sector,100 people in the private sector,and 100 people in the non-profit sector were selected.The research result found that the majority of the responses believe that the lack of experience and training,and social factors,are the most impact areas of explaining the reasons for the existence of a gap in women’s membership in boards of directors in the three sectors.And the most important reasons for the existence of a gender gap in board membership are:there is no statutory minimum percentage for women’s representation on boards of directors,and scarcity of female competencies in general,and the lack of women occupying leadership positions.
文摘This study tackles current environmental challenges by developing innovative and eco-friendly particle boards utilizing sorghum husk, combined with recycled expanded polystyrene (EPS). This dual eco-responsible approach valorizes sorghum husk, often deemed agricultural waste, and repurposes EPS, a plastic waste, thus contributing to CO2 emission reduction and effective waste management. The manufacturing process involves dissolving recycled polystyrene within a solvent to create a binder, which is then mixed with sorghum husk and cold-pressed into composite boards. The study explores the impact of two particle sizes (fine and coarse) and two different concentrations of the recycled EPS binder. Results demonstrate significant variations in the boards’ mechanical properties, displaying a range of Modulus of Rupture (MOR) from 0.84 MPa to 3.85 MPa, and Modulus of Elasticity (MOE) spanning from 658.13 MPa to 1313.25 MPa, influenced by the binder concentration and particle size. These characteristics suggest that the boards can be effectively used in various construction applications, including interior decoration, false ceilings, and potentially for furniture and door manufacturing when combined with appropriate coatings. This study not only exemplifies the valorization of plastic and agricultural wastes but also offers a practical, localized solution to global climate change challenges by promoting sustainable construction materials.
文摘The existing systems sustained with the investments made require more automation and digital transformation with the continuous advancement of tech-nology.The aviation industry is a sector that is open to more automation and digi-tal transformation,mainly because of the intense competition and the analysis of a large variety of data.The long duration of operations in current airline processes and some processflows cause customer dissatisfaction and cost increase.In this study,the boarding process,which is one of the operational processes of airline transportation and is open to improvement,was discussed.The classical boarding process has been redesigned using Internet of Things technology a model called Boarding 4.0 was created.With Boarding 4.0,it is aimed to design a process where passengers can take their time before boarding more efficiently.In the study,the sub-processes of the Boarding 4.0 model,other processes that the sub-processes interact with,their activities,and data exchange passenger move-ments during the activities are explained in detail.Compared to the classical boarding process and Boarding 4.0 with the fuzzy ahp technique,it has been shown that boarding 4.0 is more advantageous and passenger movement times can be reduced during boarding.As a result of the evaluation made with the fuzzy ahp,it was determined that boarding 4.0 is more advantageous than the classical boarding process.In addition,when the total time of the sub-activities in the board-ing process is calculated,boarding activities for a passenger take 50 min with the classic boarding process and 20 min with Boarding 4.0.Thus,when Boarding 4.0 is used,the passenger gains 30 min.Furthermore,when the calculation is made concerning the airport’s current capacity,two passengers are hosted with the clas-sical boarding process,whilefive passengers are hosted with Boarding 4.0.This acquisition is significant for airports in terms of efficient use of resources.
基金Funded by the Specialized Research Fund for the Doctoral Program of Higher Education of China (No. 20050487017)
文摘Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,polystyrene granule mortar and polyurethane foam in order to study the weatherablility of external thermal insulation system(ETIS).The change rules of adhesive strength were hereby studied at different time period of atmospheric exposure tests.The experimental results show that the adhesive strength of three kinds of ETIS changes a little during high temperature-spraying water cycle,but the adhesive strength of ETIS with EPS board decreases significantly after heating-refrigeration cycle.The lowering rate of adhesive strength with painting finishes is obviously faster than that of tile finishes for ETIS of EPS board during heating-refrigeration cycle.The weatherability of ETIS with EPS board is worse than the other two,and ETIS of polystyrene granule mortar and polyurethane foam are more suitable than ETIS of EPS board in cold area.
文摘The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and compared with experimental results to verify the reliability of the numerical simulation method.Accordingly,the concept of splitter structural coefficients was proposed.Based on the results of this study,we recommend a selection range of 5≤k≤6 for the structure factor k of the splitter;after optimization,the maximum deviation of the splitter outlet flow was reduced from the original value of 100%to 8.3%.
文摘In this paper, we conduct research on the pragmatics of politeness principle of bulletin board system based on the differences of gender and habits. The openness of the Internet makes all kinds of information received into the vision of an equal chance and web sites in order to improve the hit rate which causes the traffic of commercial purposes such as tabloidization tend to be more negative news spread. To strengthen the research of network language management strategy, it has very important theoretical significance and practical meaning analyzed. Our proposed methodology will help researchers to understand the approaches to use the pragrnatics of politeness.
基金supported in part by the IoT Intelligent Microsystem Center of Tsinghua University-China Mobile Joint Research Institute.
文摘Automated optical inspection(AOI)is a significant process in printed circuit board assembly(PCBA)production lines which aims to detect tiny defects in PCBAs.Existing AOI equipment has several deficiencies including low throughput,large computation cost,high latency,and poor flexibility,which limits the efficiency of online PCBA inspection.In this paper,a novel PCBA defect detection method based on a lightweight deep convolution neural network is proposed.In this method,the semantic segmentation model is combined with a rule-based defect recognition algorithm to build up a defect detection frame-work.To improve the performance of the model,extensive real PCBA images are collected from production lines as datasets.Some optimization methods have been applied in the model according to production demand and enable integration in lightweight computing devices.Experiment results show that the production line using our method realizes a throughput more than three times higher than traditional methods.Our method can be integrated into a lightweight inference system and pro-mote the flexibility of AOI.The proposed method builds up a general paradigm and excellent example for model design and optimization oriented towards industrial requirements.
基金funded by National Natural Science Foundation of China(No.12002392).
文摘Five types of polyurea elastomers were synthesized by changing the isocyanate component and the mechanical properties of polyurea materials were measured. Fiber-reinforced cement boards(FRCB)strengthened by polyurea with different formulations were processed, and a series of experiments were carried out on the specimens with gas explosion devices. The results showed that the conventional mechanical properties of different types of polyureas had their own advantages. Based on the gas explosion overpressure criterion, the blast resistances of reinforced plates were quantitatively evaluated,and the best polyurea was selected to guide the formulation design. The three typical failure modes of polyurea-reinforced FRCBs were flexural, shear, and flexural-shear failure. Dynamic thermodynamics and shock wave spectral analysis revealed that the polyurea did not undergo a glass transition in the gas explosion tests but retained its elastic properties, allowing it to effectively wrap the fragments formed by the brittle substrates.
文摘The present analytical review is devoted to the current problem of thermodynamic stability and related thermodynamic characteristics of the following graphene layers systems: 1) double-side hydrogenated graphene of composition CH (theoretical graphane) (Sofo et al. 2007) and experimental graphane (Elias et al. 2009);2) theoretical single-side hydrogenated graphene of composition CH;3) theoretical single-side hydrogenated graphene of composition C2H (graphone);4) experimental hydrogenated epitaxial graphene, bilayer graphene and a few layers of graphene on SiO2 or other substrates;5) experimental and theoretical single-external side hydrogenated single-walled carbon nanotubes, and experimental hydrofullerene C60H36;6) experimental single-internal side hydrogenated (up to C2H or CH composition) graphene nanoblisters with intercalated high pressure H2 gas inside them, formed on a surface of highly oriented pyrolytic graphite or epitaxial graphene under the atomic hydrogen treatment;and 7) experimental hydrogenated graphite nanofibers-multigraphene with intercalated solid H2 nano-regions of high density inside them, relevant to solving the problem of hydrogen on-board storage (Nechaev 2011-2012).
文摘Starting from the corrosion mechanism,this paper analyzes the characteristics of various types of stainless steel and selects the best performance composite plate composite plate stainless steel.Analyze and select the most suitable corrosion detection method based on specific practical multi working conditions,discuss the interference factors that affect metal corrosion during experimental simulation,and the advantages of newly developed sheet metal.The new development of composite board panels,with the substrate and composite materials applying their respective capabilities for MED,will bring breakthrough progress to the scientific research and engineering applica-tion of composite boards.
基金This work was funded by the Natural Science Research Project of Higher Education Institutions in Jiangsu Province(No.20KJA520007)Min Zhang receives the grant and the URLs to sponsors’websites are http://jyt.jiangsu.gov.cn/.
文摘For Printed Circuit Board(PCB)surface defect detection,traditional detection methods mostly focus on template matching-based reference method and manual detections,which have the disadvantages of low defect detection efficiency,large errors in defect identification and localization,and low versatility of detectionmethods.In order to furthermeet the requirements of high detection accuracy,real-time and interactivity required by the PCB industry in actual production life.In the current work,we improve the Youonly-look-once(YOLOv4)defect detection method to train and detect six types of PCB small target defects.Firstly,the original Cross Stage Partial Darknet53(CSPDarknet53)backbone network is preserved for PCB defect feature information extraction,and secondly,the original multi-layer cascade fusion method is changed to a single-layer feature layer structure to greatly avoid the problem of uneven distribution of priori anchor boxes size in PCB defect detection process.Then,the K-means++clustering method is used to accurately cluster the anchor boxes to obtain the required size requirements for the defect detection,which further improves the recognition and localization of small PCB defects.Finally,the improved YOLOv4 defect detection model is compared and analyzed on PCB dataset with multi-class algorithms.The experimental results show that the average detection accuracy value of the improved defect detection model reaches 99.34%,which has better detection capability,lower leakage rate and false detection rate for PCB defects in comparison with similar defect detection algorithms.
基金funded by the National Natural Science Foundation of China(72172164)Natural Science Foundation of Guangdong Province(2021A1515011354).
文摘We introduce evolutionary game method to analyze low-price collusion in inquiry market of Sci-Tech Innovation Board of China(SIBC)from the perspective of strategic interaction between large institutional investors(LIIs),small and medium-sized institutional investors(SMIIs),and supervision department(SD).The results show that supervision behaviors of SD,and quotation behaviors of institutional investors,are subject to supervision conditions.Under the condition that benefits of tough supervision are lower a lot than minimum benefits of light supervision(light supervision condition),SD will choose light supervision and institutional investors will turn to illegal quotation in response.Finally,a steady-state equilibrium with low-price collusion will form in SIBC’s inquiry market even with a large supervision penalty for illegal quotation.On the contrary,under the condition that benefits of tough supervision are higher a lot than maximum benefits of light supervision(tough supervision condition)and with a large penalty for illegal quotation,SD and institutional investors will choose tough supervision and legal quotation.Further numerical simulations under light supervision condition show that:(1)High-price culling rule will become a booster for low-price collusion and accelerate SMIIs’evolutionary process to imitative quotation.(2)Blindly increasing penalties for illegal quotation or reducing the culling rate is not an appropriate approach to solve the problem of low-price collusion since it cannot shift supervision condition from light into tough and make SD supervise toughly.(3)Institutional investors’choices of quotation strategies are more volatile and highly susceptible to supervision behaviors of SD when facing exogenous uncertainty.Therefore,the keys to solving the problem of low-price collusion are shifting supervision condition from light into tough through increasing incremental benefits of tough supervision,and providing institutional investors with a stable and predictable supervision policy.In conclusion,the creation of a fair inquiry market doesn’t only depend on restraint and punishment to institutional investors,but also requires the establishment of supervision mechanism those are compatible with market-based inquiry.
基金National Natural Science Foundation of China(No.51805079)Fundamental Research Funds for the Central Universities,China(No.2232021D-15)Shanghai Science and Technology Program(No.20DZ2251400)。
文摘The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole processing.The problem of optimal control of its drilling force is one of the main factors affecting the quality of micro-hole machining.To address this problem,the thrust forces and torques in PCB drilling were first modeled and analyzed,and the corresponding prediction models were established.The drilling force analysis was carried out through the micro-hole drilling experiment,the specific cutting energy under different feed rates was calculated,the influence of the size effect was clarified,and the accuracy of the prediction model was verified.The result shows that during the drilling of glass fiber cloth,changes in the material removal mechanism are induced as the feed per revolution is varied.When the feed per revolution is less than the tool edge radius,the glass fiber is not cut by the main cutting edge,but is crushed and broken.When the feed per revolution is greater than the radius of the tool edge,the glass fiber is cut by the main cutting edge.At the same time,the established analytical model can accurately reflect the influence of the size effect on the drilling torque in PCB micro-hole drilling,and the error is within 10%.This method has certain practical application value in controlling PCB micro hole processing quality.
基金supported by the National Key Basic Research Program of China 973 Project(No.2012CB026104)National Natural Science Foundation of China(No.41271072 and No.51378057)Service Performance Evaluation of the Subsidiary Structure in The Permafrost Regions of the Qinghai Tibet Plateau(2014-07-01)
文摘On the basis of on-site measured data of the newly constructed Gonghe-Yushu Highway in a permafrost region, this paper analyzed thermal conditions of the subgrade with XPS insulated board according to different selected monitoring sections in various locations. We also summarized the geothermal distribution and change rules of subgrade with XPS insulation board under the asphalt pavement in summarized a high temperature frozen soil region. It is suggested that the shoulder of subgrade with XPS insulation board be widen to a reasonable width so as to keep the subgrade stable.
文摘Density and resin content are two factors that have a significant effect on the production cost of wood composite. However, particle size affects resin content and density, which suggests that the interaction of these three factors can be manipulated to reduce the board density and resin content of particleboard without adversely influencing its mechanical properties. Some mathematical functional forms based on resin content, board density and slenderness ratio were regressed and an appropriate form was chosen. According to analysis of the results using SHAZAM 9 software, the exponential function best fit the experimental data. Finally, "indifference curves" of mechanical properties were illustrated and analyzed. The results indicated that negative effects of density or resin content reduction on mechanical properties could be compensated for by controlling particles' slenderness ratio. Interestingly, increases in slenderness ratio compensated for the negative effects of decreases in resin content or board density on module of rupture (MOR) and module of elasticity (MOE). Moreover, this "compensation ratio" intensified as resin content or density decreased and/or as the MOR or MOE increased. On the other hand, reduction in slenderness ratio indicated a comple- mentary effect on reducing internal bond (IB) strength, a result of decreases in resin content or density. Moreover, this "complementary ratio" was intensified as resin content or density decreased and/or as IB strength increased.
基金Supported by the Technological Research on Reforming Otter Boards of Bottom Trawl in Mauretania and Guinea(China National Fisheries Corporation,CNFC)Technological Research on Transformation and Upgrading of Shrimp Trawl in Sierra Leone(CNFC)Far Sea Fisheries Resources Monitoring and Assessment of South China Sea(No.2013050212)
文摘In this paper, we tested the hydrodynamic characteristics of a new, double-winged otter board that consists of a forewing, a leading edge slat and a trailing edge flap. Flume experiments were conducted in a circulating flume tank by using a model with an aspect ratio(AR) of 0.85 and a horizontal planform area( S) of 0.09 m^2. The results indicated that the critical angle( α_(cr)) of the model was 44°, whereas the maximum lift coefficient( C_(Lmax)) was up to 1.715, and the door efficiency( K) was 1.122. The attack angle( α) ranged from 30° to 48° and from 10° to 46° when the lift coefficient( C_L) and door efficiency( K) were greater than 1.2 and 1.0, respectively. To compare the difference between double-winged otter board and traditional Morgere Polyvalent Ovale, same model of Morgere Polyvalent Ovale was also tested under the same experimental conditions. The critical angle( α_(cr)) and maximum of lift coefficient( C_(Lmax)) of the doublewinged otter board were 37.5% and 14.6% larger than those of the Morgere Polyvalent Ovale. Therefore, we concluded that the novel, double-winged otter board was more suitable for bottom trawling fisheries in the deep water of the Mauretania Sea due to its better hydrodynamic characteristics and stability.