Cu/TiO_(2) Photocatalysts for CO_(2) Reduction: Structure and Evolution of the Cocatalyst Active Form

Extensive work on a Cu-modified TiO_(2) photocatalyst for CO_(2) reduction under visible light irradiation was conducted. The structure of the copper cocatalyst was established using UV-vis diff use refl ectance spectroscopy, high-resolution transmis- sion electron microscopy, X-ray absorption spectroscopy, and X-ray photoelectron spectroscopy. It was found that copper exists in different states (Cu 0 , Cu^(+) , and Cu^(2+) ), the content of which depends on the TiO_(2) calcination temperature and copper loading. The optimum composition of the cocatalyst has a photocatalyst based on TiO_(2) calcined at 700℃ and modified with 5 wt% copper, the activity of which is 22 μmol/(h·g cat ) (409 nm). Analysis of the photocatalysts after the photocatalytic reaction disclosed that the copper metal on the surface of the calcined TiO_(2) was gradually converted into Cu_(2) O during the photocatalytic reaction. Meanwhile, the metallic copper on the surface of the noncalcined TiO_(2) did not undergo any trans- formation during the reaction.

Heterojunction-engineered carrier transport in elevated-metal metal-oxide thin-film transistors

This study investigates the carrier transport of heterojunction channel in oxide semiconductor thin-film transistor(TFT)using the elevated-metal metal-oxide(EMMO)architecture and indium−zinc oxide(InZnO).The heterojunction band diagram of InZnO bilayer was modified by the cation composition to form the two-dimensional electron gas(2DEG)at the interface quantum well,as verified using a metal−insulator−semiconductor(MIS)device.Although the 2DEG indeed contributes to a higher mobility than the monolayer channel,the competition and cooperation between the gate field and the built-in field strongly affect such mobility-boosting effect,originating from the carrier inelastic collision at the heterojunction interface and the gate field-induced suppression of quantum well.Benefited from the proper energy-band engineering,a high mobility of 84.3 cm2·V^(−1)·s^(−1),a decent threshold voltage(V_(th))of−6.5 V,and a steep subthreshold swing(SS)of 0.29 V/dec were obtained in InZnO-based heterojunction TFT.

Indispensable gutter layers in thin-film composite membranes for carbon capture

Industrial thin-film composite(TFC)membranes achieve superior gas separation properties from high-performance selective layer materials,while the success of membrane technology relies on high-performance gutter layers to achieve production scalability and low-cost manufacturing.However,the current literature predominantly focuses on the design of polymer architectures to obtain high permeability and selectivity,while the art of fabricating gutter layers is usually safeguarded by industrial manufacturers and appears lackluster to academic researchers.This is the first report aiming to provide a comprehensive and critical review of state-of-the-art gutter layer materials and their design and modification to enable TFC membranes with superior separation performance.We first elucidate the importance of the gutter layer on membrane performance through modeling and experimental results.Then various gutter layer materials used to obtain high-performance composite membranes are critically reviewed,and the strategies to improve their compatibility with the selective layer are highlighted,such as oxygen plasma treatment,polydopamine deposition,and surface grafting.Finally,we present the opportunities of the gutter layer design for practical applications.

Implementation of sub-100 nm vertical channel-all-around(CAA) thin-film transistor using thermal atomic layer deposited IGZO channel

In-Ga-Zn-O(IGZO) channel based thin-film transistors(TFT), which exhibit high on-off current ratio and relatively high mobility, has been widely researched due to its back end of line(BEOL)-compatible potential for the next generation dynamic random access memory(DRAM) application. In this work, thermal atomic layer deposition(TALD) indium gallium zinc oxide(IGZO) technology was explored. It was found that the atomic composition and the physical properties of the IGZO films can be modulated by changing the sub-cycles number during atomic layer deposition(ALD) process. In addition, thin-film transistors(TFTs) with vertical channel-all-around(CAA) structure were realized to explore the influence of different IGZO films as channel layers on the performance of transistors. Our research demonstrates that TALD is crucial for high density integration technology, and the proposed vertical IGZO CAA-TFT provides a feasible path to break through the technical problems for the continuous scale of electronic equipment.

Numerical Study and Optimization of CZTS-Based Thin-Film Solar Cell Structure with Different Novel Buffer-Layer Materials Using SCAPS-1D Software

This study explored the performances of CZTS-based thin-film solar cell with three novel buffer layer materials ZnS, CdS, and CdZnS, as well as with variation in thickness of buffer and absorber-layer, doping concentrations of absorber-layer material and operating temperature. Our aims focused to identify the most optimal thin-film solar cell structure that offers high efficiency and lower toxicity which are desirable for sustainable and eco-friendly energy sources globally. SCAPS-1D, widely used software for modeling and simulating solar cells, has been used and solar cell fundamental performance parameters such as open-circuited voltage (), short-circuited current density (), fill-factor() and efficiency() have been optimized in this study. Based on our simulation results, it was found that CZTS solar cell with Cd0.4Zn0.6S as buffer-layer offers the most optimal combination of high efficiency and lower toxicity in comparison to other structure investigated in our study. Although the efficiency of Cd0.4Zn0.6S, ZnS and CdS are comparable, Cd0.4Zn0.6S is preferable to use as buffer-layer for its non-toxic property. In addition, evaluation of performance as a function of buffer-layer thickness for Cd0.4Zn0.6S, ZnS and CdS showed that optimum buffer-layer thickness for Cd0.4Zn0.6S was in the range from 50 to 150nm while ZnS offered only 50 – 75 nm. Furthermore, the temperature dependence performance parameters evaluation revealed that it is better to operate solar cell at temperature 290K for stable operation with optimum performances. This study would provide valuable insights into design and optimization of nanotechnology-based solar energy technology for minimizing global energy crisis and developing eco-friendly energy sources sustainable and simultaneously.

TiO2-PES Fibrous Composite Material for Ammonia Removal Using UV-A Photocatalyst

This study focused on the development and characterization of TiO2-PES composite fibers with varying TiO2 loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO2 nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO2 composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO2 composite fibers as promising photocatalysts for ammonia removal in water treatment applications.

Numerical Analysis on the Effect of n-Si on Cu(In, Ga)Se2 Based Thin-Films for High-Performance Solar Cells by 1D-SCAPS

We report the performances of a chalcopyrite Cu(In, Ga)Se2 CIGS-based thin-film solar cell with a newly employed high conductive n-Si layer. The data analysis was performed with the help of the 1D-Solar Cell Capacitance Simulator (1D-SCAPS) software program. The new device structure is based on the CIGS layer as the absorber layer, n-Si as the high conductive layer, i-In2S3, and i-ZnO as the buffer and window layers, respectively. The optimum CIGS bandgap was determined first and used to simulate and analyze the cell performance throughout the experiment. This analysis revealed that the absorber layer’s optimum bandgap value has to be 1.4 eV to achieve maximum efficiency of 22.57%. Subsequently, output solar cell parameters were analyzed as a function of CIGS layer thickness, defect density, and the operating temperature with an optimized n-Si layer. The newly modeled device has a p-CIGS/n-Si/In2S3/Al-ZnO structure. The main objective was to improve the overall cell performance while optimizing the thickness of absorber layers, defect density, bandgap, and operating temperature with the newly employed optimized n-Si layer. The increase of absorber layer thickness from 0.2 - 2 µm showed an upward trend in the cell’s performance, while the increase of defect density and operating temperature showed a downward trend in solar cell performance. This study illustrates that the proposed cell structure shows higher cell performances and can be fabricated on the lab-scale and industrial levels.

Solar fuel generation over nature-inspired recyclable TiO_(2)/g-C_(3)N_(4)S-scheme hierarchical thin-film photocatalyst

Preparation of efficient photocatalysts with ease of recovery in solar fuel generation is highly desired to achieve carbon neutralization in carbon dioxide(CO_(2))emissions.Inspired from the forest with superior light penetration and fast gas transport,a TiO_(2)/g-C_(3)N_(4)composite nanowire arrays(NAs)film with maximized light utilization is devised.It is achieved by in-situ coating a thin layer of g-C_(3)N_(4)(as the leaf)on the vertically-oriented TiO_(2)arrays(as tree trunks)on Ti foil(as soil).Benefiting from the effective charge separation by S-scheme charge transfer,intimate contact by the in-situ growth as well as the ingenious structure,the composite,readily recyclable,displays exciting performance in photocatalytic CO_(2)reduction.It is beyond doubt that the combination of heterojunction construction and“nature-inspired biomimetic photocatalyst”design promises practical applications and industrial use.

All-Solid-State Thin-Film Lithium-Sulfur Batteries

Lithium-sulfur(Li-S)system coupled with thin-film solid electrolyte as a novel high-energy micro-battery has enormous potential for complementing embedded energy harvesters to enable the autonomy of the Internet of Things microdevice.However,the volatility in high vacuum and intrinsic sluggish kinetics of S hinder researchers from empirically integrating it into allsolid-state thin-film batteries,leading to inexperience in fabricating all-solid-state thin-film Li-S batteries(TFLSBs).Herein,for the first time,TFLSBs have been successfully constructed by stacking vertical graphene nanosheets-Li2S(VGsLi2S)composite thin-film cathode,lithium-phosphorous-oxynitride(LiPON)thin-film solid electrolyte,and Li metal anode.Fundamentally eliminating Lipolysulfide shuttle effect and maintaining a stable VGs-Li2S/LiPON interface upon prolonged cycles have been well identified by employing the solid-state Li-S system with an“unlimited Li”reservoir,which exhibits excellent longterm cycling stability with a capacity retention of 81%for 3,000 cycles,and an exceptional high temperature tolerance up to 60℃.More impressively,VGs-Li2S-based TFLSBs with evaporated-Li thin-film anode also demonstrate outstanding cycling performance over 500 cycles with a high Coulombic efficiency of 99.71%.Collectively,this study presents a new development strategy for secure and high-performance rechargeable all-solid-state thin-film batteries.

A Metal-free Polyimide Photocatalyst for the Oxidation of Amines to Imines

Polyimide(PI) is an organic polymer material with good stability and diverse sources that has attracted widespread attention in the field of photocatalysis. In this study, a series of PI photocatalysts were synthesized by a thermal polymerization approach using pyromellitic dianhydride(PMDA) and various diamine monomers(melamine(MA), 4,4′-oxydianiline, and melem) as the precursors as well as different heating rates. The effects of the diamine precursor and heating rate on the structure, composition, morphology, and optical properties of the as-prepared PI materials were systematically investigated by various characterization techniques. The selective photo-oxidation of benzylamine was used as a model reaction to evaluate the photocatalytic activities of the resulting PI samples for the oxidation of amines to imines. The results revealed that the PI sample prepared using MA and PMDA as the precursors and a heating rate of 7 ℃/min(MA-PI-7) exhibited the best catalytic performance, with 98% benzylamine conversion and 98% selectivity for N-benzylidene benzylamine after 4 h of irradiation. Several benzylamine derivatives and heterocyclic amines also underwent the photo-oxidation reaction over the MA-PI-7 catalyst to afford the corresponding imines with good activity. In addition, MA-PI-7 exhibited good stability over four successive photocatalytic cycles.

Recent progress in research and design concepts for the characterization,testing,and photocatalysts for nitrogen reduction reaction

The reduction of molecular nitrogen(N_(2))to ammonia(NH_(3))under mild conditions is one of the most promising studies in the energy field due to the important role of NH_(3)in modern industry,production,and life.The photocatalytic reduction of N_(2)is expected to achieve clean and sustainable NH_(3)production by using clean solar energy.To date,the new photocatalysts for photocatalytic reduction of N_(2)to NH_(3)at room temperature and atmospheric pressure have not been fully developed.The major challenge is to achieve high light-absorption efficiency,conversion efficiency,and stability of photocatalysts.Herein,the methods for measuring produced NH_(3)are compared,and the problems related to possible NH_(3)pollution in photocatalytic systems are mentioned to provide accurate ideas for measuring photocatalytic efficiency.The recent progress of nitrogen reduction reaction(NRR)photocatalysts at ambient temperature and pressure is summarized by introducing charge transfer,migration,and separation in photocatalytic NRR,which provides a guidance for the selection of future photocatalyst.More importantly,we introduce the latest research strategies of photocatalysts in detail,which can guide the preparation and design of photocatalysts with high NRR activity.

Recent advances in bismuth-based photocatalysts:Environment and energy applications

Photocatalysis is an effective way to solve the problems of environmental pollution and energy shortage.Numerous photocatalysts have been developed and various strategies have been proposed to improve the photocatalytic performance.Among them,Bi-based photocatalysts have become one of the most popular research topics due to their suitable band gaps,unique layered structures,and physicochemical properties.In this review,Bi-based photocatalysts(BiOX,BiVO_(4),Bi_(2)S_(3),Bi_(2)MoO_(6),and other Bi-based photocatalysts)have been summarized in the field of photocatalysis,including their applications of the removal of organic pollutants,hydrogen production,oxygen production etc.The preparation strategies on how to improve the photocatalytic performance and the possible photocatalytic mechanism are also summarized,which could supply new insights for fabricating high-efficient Bi-based photocatalysts.Finally,we summarize the current challenges and make a reasonable outlook on the future development direction of Bi-based photocatalysts.

Stability of high-salinity-enhanced foam:Surface behavior and thin-film drainage

Cocamidopropyl hydroxyl sulfobetaine(CHSB)is one of the most promising foaming agents for high-salinity reservoirs because the salt in place facilitates its foam stability,even with salinity as high as 2×10^(5)mg/L.However,the synergistic effects between CHSB and salt have not been fully understood.This study utilized bulk foam tests and thin-film interferometry to comprehensively investigate the macroscopic and microscopic decay processes of CHSB foams with NaCl concentrations ranging from 2.3×10^(4)to 2.1×10^(5)mg/L.We focused on the dilatational viscoelasticity and dynamic thin-film thickness to elucidate the high-salinity-enhanced foam stability.The increase in dilatational viscoelasticity and supramolecular oscillating structural force(Π_(OS))with salinity dominated the superior stability of CHSB foam.With increasing salinity,more CHSB molecules accumulated on the surface with a lower diffusion rate,leading to high dilatational moduli and surface elasticity,thus decelerating coarsening and coalescence.Meanwhile,the number density of micelles in the thin film increased with salinity,resulting in increasedΠOS.Consequently,the energy barrier for stepwise thinning intensified,and the thin-film drainage slowed.This work conduces to understand the mechanisms behind the pronounced stability of betaine foam and can promote the widespread application of foam in harsh reservoirs.

Waste fly ash-ZnO as a novel sunlight-responsive photocatalyst for dye discoloration

Treating waste with a waste material using freely available solar energy is the most effective way towards sustainable future.In this study,a novel photocatalyst,partly derived from waste material from the coal industry,was developed.Fly ash hybridized with ZnO(FAeZn)was synthesized as a potential photocatalyst for dye discoloration.The synthesized photocatalyst was characterized by X-ray diffraction,scanning electron microscopy,transmission electron microscopy,and ultravioletevisible/near infra-red spectroscopy.The photocatalytic activity was examined with the discoloration of methylene blue used as synthetic dye wastewater.All the experiments were performed in direct sunlight.The photocatalytic performance of FAeZn was found to be better than that of ZnO and the conventionally popular TiO2.The LangmuireHinshelwood model rate constant values of ZnO,TiO2,and FAeZn were found to be 0.016 min1,0.017 min1,and 0.020 min1,respectively.There were two reasons for this:(1)FAeZn was able to utilize both ultraviolet and visible parts of the solar spectrum,and(2)its BrunauereEmmetteTeller surface area and porosity were significantly enhanced.This led to increased photon absorption and dye adsorption,thus exhibiting an energy-efficient performance.Therefore,FAeZn,partly derived from waste,can serve as a suitable material for environmental remediation and practical solar energy applications.

Low-temperature metal–oxide thin-film transistor technologies for implementing flexible electronic circuits and systems

Here we review two 300℃metal–oxide(MO)thin-film transistor(TFT)technologies for the implementation of flexible electronic circuits and systems.Fluorination-enhanced TFTs for suppressing the variation and shift of turn-on voltage(VON),and dual-gate TFTs for acquiring sensor signals and modulating VON have been deployed to improve the robustness and performance of the systems in which they are deployed.Digital circuit building blocks based on fluorinated TFTs have been designed,fabricated,and characterized,which demonstrate the utility of the proposed low-temperature TFT technologies for implementing flexible electronic systems.The construction and characterization of an analog front-end system for the acquisition of bio-potential signals and an active-matrix sensor array for the acquisition of tactile images have been reported recently.

Recycling Spent LiCoO_(2)Battery as a High-efficient Lithiumdoped Graphitic Carbon Nitride/Co_(3)O_(4)Composite Photocatalyst and Its Synergistic Photocatalytic Mechanism

The ever-increasing quantity of spent lithium-ion batteries(LIBs)is both a potential environmental pollutant and a valuable resource.The spent LIBs recycling mainly aimed at the separation of valuable elements.Some issues still exist in these processes such as high energy consumption and complex separation procedures.This study avoided element separation and proposed a facile approach to transform spent LiCoO_(2) electrode into a lithium(Li)-doped graphitic carbon nitride(g-C_(3)N_(4))/Co_(3)O_(4) composite photocatalyst through one-pot in situ thermal reduction.During the thermal process,melamine served as the reductant for LiCoO_(2) decomposition and the raw material for g-C_(3)N_(4) production.Li was in situ doped in g-C_(3)N_(4) and the generated Co_(3)O_(4) was in situ integrated,forming a Li-doped g-C_(3)N_(4)/Co_(3)O_(4) composite photocatalyst.This special composite exhibited an enhanced photocatalytic performance,and its photocatalytic H2 production and RhB degradation rates were 8.7 and 6.8 times higher than those of g-C_(3)N_(4).The experiments combined with DFT calculation revealed that such enhanced photocatalytic efficiency was ascribed to the synergy effect of Li doping and Co_(3)O_(4) integrating,which extended the visible light absorption(450-900 nm)and facilitated the charge transfer and separation.This study transforms waste into a high-efficient catalyst,realizing high-valued utilization of waste and environmental protection.

Fluorination-mitigated high-current degradation of amorphous InGaZnO thin-film transistors

As growing applications demand higher driving currents of oxide semiconductor thin-film transistors(TFTs),severe instabilities and even hard breakdown under high-current stress(HCS)become critical challenges.In this work,the triggering voltage of HCS-induced self-heating(SH)degradation is defined in the output characteristics of amorphous indium-galliumzinc oxide(a-IGZO)TFTs,and used to quantitatively evaluate the thermal generation process of channel donor defects.The fluorinated a-IGZO(a-IGZO:F)was adopted to effectively retard the triggering of the self-heating(SH)effect,and was supposed to originate from the less population of initial deep-state defects and a slower rate of thermal defect transition in a-IGZO:F.The proposed scheme noticeably enhances the high-current applications of oxide TFTs.

Enhanced efficiency of the Sb_(2)Se_(3)thin-film solar cell by the anode passivation using an organic small molecular of TCTA

Antimony selenide(Sb_(2)Se_(3))is an emerging solar cell material.Here,we demonstrate that an organic small molecule of 4,4',4''-tris(carbazol-9-yl)-triphenylamine(TCTA)can efficiently passivate the anode interface of the Sb_(2)Se_(3)solar cell.We fabricated the device by the vacuum thermal evaporation,and took ITO/TCTA(3.0 nm)/Sb_(2)Se_(3)(50 nm)/C60(5.0 nm)/Alq3(3.0 nm)/Al as the device architecture,where Alq3 is the tris(8-hydroxyquinolinato)aluminum.By introducing a TCTA layer,the open-circuit voltage is raised from 0.36 to 0.42 V,and the power conversion efficiency is significantly improved from 3.2%to 4.3%.The TCTA layer not only inhibits the chemical reaction between the ITO and Sb_(2)Se_(3)during the annealing process but it also blocks the electron diffusion from Sb_(2)Se_(3)to ITO anode.The enhanced performance is mainly attributed to the suppression of the charge recombination at the anode interface.

High-performance amorphous In–Ga–Zn–O thin-film transistor nonvolatile memory with a novel p-SnO/n-SnO_(2) heterojunction charge trapping stack

Amorphous In–Ga–Zn–O(a-IGZO)thin-film transistor(TFT)memories with novel p-SnO/n-SnO_(2) heterojunction charge trapping stacks(CTSs)are investigated comparatively under a maximum fabrication temperature of 280℃.Compared to a single p-SnO or n-SnO_(2) charge trapping layer(CTL),the heterojunction CTSs can achieve electrically programmable and erasable characteristics as well as good data retention.Of the two CTSs,the tunneling layer/p-SnO/nSnO_(2)/blocking layer architecture demonstrates much higher program efficiency,more robust data retention,and comparably superior erase characteristics.The resulting memory window is as large as 6.66 V after programming at 13 V/1 ms and erasing at-8 V/1 ms,and the ten-year memory window is extrapolated to be 4.41 V.This is attributed to shallow traps in p-SnO and deep traps in n-SnO_(2),and the formation of a built-in electric field in the heterojunction.

Advances in mobility enhancement of ITZO thin-film transistors:a review

Indium-tin-zinc oxide(ITZO)thin-film transistor(TFT)technology holds promise for achieving high mobility and offers significant opportunities for commercialization.This paper provides a review of progress made in improving the mobility of ITZO TFTs.This paper begins by describing the development and current status of metal-oxide TFTs,and then goes on to explain the advantages of selecting ITZO as the TFT channel layer.The evaluation criteria for TFTs are subsequently introduced,and the reasons and significance of enhancing mobility are clarified.This paper then explores the development of high-mobility ITZO TFTs from five perspectives:active layer optimization,gate dielectric optimization,electrode optimization,interface optimization,and device structure optimization.Finally,a summary and outlook of the research field are presented.