The mechanical properties and microstructure of two low carbon high manganese steels with 23.8% （No. 1） and 33% （No. 2） （mass percent） of manganese were investigated. The results showed that No. 1 steel possesse...The mechanical properties and microstructure of two low carbon high manganese steels with 23.8% （No. 1） and 33% （No. 2） （mass percent） of manganese were investigated. The results showed that No. 1 steel possesses high strength and high plasticity, and No. 2 steel has a relatively high strength and extraordinary plasticity. The No. 1 steel exhibits both TRIP （transformation induced plasticity） and TWIP （twin induced plasticity） effects during the deformation; while only TWIP effect appeared under the same deformation condition for No. 2 steel. The comparison between the microstructures and mechanical properties of two steels was made, and the strengthening mechanisms were also analyzed.展开更多
Stainless steels are used in a wide range of complex environments due to their excellent corrosion resistance.Multiphase stainless steels can offer an excellent combination of strength,toughness and corrosion resistan...Stainless steels are used in a wide range of complex environments due to their excellent corrosion resistance.Multiphase stainless steels can offer an excellent combination of strength,toughness and corrosion resistance due to the coexistence of different microstructures.The microstructure and mechanical properties of a novel cast multiphase stainless steel,composed of martensite,ferrite,and austenite,were investigated following appropriate heat treatment processes:solution treatment at 1,050℃ for 0.5 h followed by water quenching to room temperature,and aging treatment at 500℃ for 4 h followed by water quenching to room temperature.Results show reversed austenite is formed by diffusion of Ni element during aging process,and the enrichment of Ni atoms directly determines the mechanical stability of austenite.The austenite with a lower Ni content undergoes a martensitic transformation during plastic deformation.The tensile strength of the specimen exceeds 1,100 MPa and the elongation exceeds 24%after solid solution,and further increases to 1,247 MPa and 25%after aging treatment.This enhancement is due to the TRIP effect of austenite and the precipitation of the nanoscale G-phase pinning dislocations in ferrite and martensite.展开更多
The mechanical property and forming limit experiments were carried out on a higli manganese TRIP/TWIP steels with manganese of 18.8%. And the forming /imit diagram was obtained. This hig：h manganese steel shows outst...The mechanical property and forming limit experiments were carried out on a higli manganese TRIP/TWIP steels with manganese of 18.8%. And the forming /imit diagram was obtained. This hig：h manganese steel shows outstanding mechanical properties comhining high strength with good formability. Its limit plane strain corresponding to the lowest point in the plain strain condition is about 38%. The effects of conventional mechanical property on the limit plane strain were analyzed. With increasing the content of Mn, the limit plane strain increases, indicating that TWlP effect is advantageous to the increase of formability. Combining with three classical models and volume invaria ble principle, a FLD model was buih, which is suitable for high manganese steels very well.展开更多
Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning ele...Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electron backscattered diffraction （EBSD）. Before deformation, the morphology of α＇- M depended mainly on the number of variants and growing period. Regardless of martensite morphologies and deformation, the Kurdjumov-Sachs （K-S） orientation relationships always maintained. The 6 α＇-M variants formed from a plate of ε-M were of 3 pairs of twins with a common axis 〈110〉α＇ parallel to the normal of {112}γ habit plane to minimize transformation strain. When α＇-M could be formed only by deformation, it nucleated at the intersection of ε-M variants and grew mainly in thick ε-M plates. Thick ε plates promoted significantly the α＇-M and weakened the influence of grain orientations. During tension, the transformation in 〈100〉-oriented grains was observed to be slower than that in 〈121〉-oriented grains. Deformation twins promoted ε-M formation slightly and had no apparent effect on α＇-M. Deformation increased the number of ε-M variants, but reduced that of α＇-M variants.展开更多
The mechanical behavior and microstructural evolution of an Fe-30Mn-3Al-3Si twinninginduced plasticity(TWIP)steel processed using warm forging was investigated.It is found that steel processed via warm forging improve...The mechanical behavior and microstructural evolution of an Fe-30Mn-3Al-3Si twinninginduced plasticity(TWIP)steel processed using warm forging was investigated.It is found that steel processed via warm forging improves comprehensive mechanical properties compared to the TWIP steel processed via cold rolling,with a high tensile strength(R_(m))of 793 MPa,a yield strength(R_(P))of 682 MPa,an extremely large R_(P)/R_(m)ratio as high as 0.86 as well as an excellent elongation rate of 46.8%.The microstructure observation demonstrates that steel processed by warm forging consists of large and elongated grains together with fine,equiaxed grains.Complicated micro-defect configurations were also observed within the steel,including dense dislocation networks and a few coarse deformation twins.As the plastic deformation proceeds,the densities of dislocations and deformation twins significantly increase.Moreover,a great number of slip lines could be observed in the elongated grains.These findings reveal that a much more dramatic interaction between microstructural defect and dislocations glide takes place in the forging sample,wherein the fine and equiaxed grains propagated dislocations more rapidly,together with initial defect configurations,are responsible for enhanced strength properties.Meanwhile,larger,elongated grains with more prevalently activated deformation twins result in high plasticity.展开更多
Reasons for substution of Al and/or Si by P in TRIP steel were described.The details in thermodynamic and kinetic analyses and model parametre for the estimation,as well as the calculation results were listed.Low temp...Reasons for substution of Al and/or Si by P in TRIP steel were described.The details in thermodynamic and kinetic analyses and model parametre for the estimation,as well as the calculation results were listed.Low temperature tests were also shown to support the calculation result.Strengthening mechanism for different composition high Mn steels was discussed based on the optical micrograph,XRD,TEM and SEM measurements.It was therefore realized stack fault and its effect in phase transformation in high Mn steel was in the dependence of composition,strain and heat treatment.展开更多
文摘The mechanical properties and microstructure of two low carbon high manganese steels with 23.8% （No. 1） and 33% （No. 2） （mass percent） of manganese were investigated. The results showed that No. 1 steel possesses high strength and high plasticity, and No. 2 steel has a relatively high strength and extraordinary plasticity. The No. 1 steel exhibits both TRIP （transformation induced plasticity） and TWIP （twin induced plasticity） effects during the deformation; while only TWIP effect appeared under the same deformation condition for No. 2 steel. The comparison between the microstructures and mechanical properties of two steels was made, and the strengthening mechanisms were also analyzed.
基金supported by the Inner Mongolia Autonomous Region Science and Technology Major Special Project(Grant No.2021SZD0082).
文摘Stainless steels are used in a wide range of complex environments due to their excellent corrosion resistance.Multiphase stainless steels can offer an excellent combination of strength,toughness and corrosion resistance due to the coexistence of different microstructures.The microstructure and mechanical properties of a novel cast multiphase stainless steel,composed of martensite,ferrite,and austenite,were investigated following appropriate heat treatment processes:solution treatment at 1,050℃ for 0.5 h followed by water quenching to room temperature,and aging treatment at 500℃ for 4 h followed by water quenching to room temperature.Results show reversed austenite is formed by diffusion of Ni element during aging process,and the enrichment of Ni atoms directly determines the mechanical stability of austenite.The austenite with a lower Ni content undergoes a martensitic transformation during plastic deformation.The tensile strength of the specimen exceeds 1,100 MPa and the elongation exceeds 24%after solid solution,and further increases to 1,247 MPa and 25%after aging treatment.This enhancement is due to the TRIP effect of austenite and the precipitation of the nanoscale G-phase pinning dislocations in ferrite and martensite.
基金Item Sponsored by National Natural Science Foundation of China(50771019,50901014)Open Project Foundation of State Key Laboratory of Rolling and Automation of Northeastern University of China(2009001)
文摘The mechanical property and forming limit experiments were carried out on a higli manganese TRIP/TWIP steels with manganese of 18.8%. And the forming /imit diagram was obtained. This hig：h manganese steel shows outstanding mechanical properties comhining high strength with good formability. Its limit plane strain corresponding to the lowest point in the plain strain condition is about 38%. The effects of conventional mechanical property on the limit plane strain were analyzed. With increasing the content of Mn, the limit plane strain increases, indicating that TWlP effect is advantageous to the increase of formability. Combining with three classical models and volume invaria ble principle, a FLD model was buih, which is suitable for high manganese steels very well.
基金funded by the National Natural Science Foundation of China (No. 50771019)Specialized Research Fund for the Doctoral Program of Higher Education (No. 20090006110013)
文摘Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electron backscattered diffraction （EBSD）. Before deformation, the morphology of α＇- M depended mainly on the number of variants and growing period. Regardless of martensite morphologies and deformation, the Kurdjumov-Sachs （K-S） orientation relationships always maintained. The 6 α＇-M variants formed from a plate of ε-M were of 3 pairs of twins with a common axis 〈110〉α＇ parallel to the normal of {112}γ habit plane to minimize transformation strain. When α＇-M could be formed only by deformation, it nucleated at the intersection of ε-M variants and grew mainly in thick ε-M plates. Thick ε plates promoted significantly the α＇-M and weakened the influence of grain orientations. During tension, the transformation in 〈100〉-oriented grains was observed to be slower than that in 〈121〉-oriented grains. Deformation twins promoted ε-M formation slightly and had no apparent effect on α＇-M. Deformation increased the number of ε-M variants, but reduced that of α＇-M variants.
基金Funded by the National Natural Science Foundation of China(Nos.51701206 and 51671187)the Shanxi Natural Science Foundation(No.2019JQ-833)+2 种基金the Anhui Natural Science Foundation(1808085QE166)the Special Scientific Research Project of Shanxi Education Committee(No.19JQ0974)the Doctoral Research Initiation Project of Yan’an University(No.YDBD2018-21)。
文摘The mechanical behavior and microstructural evolution of an Fe-30Mn-3Al-3Si twinninginduced plasticity(TWIP)steel processed using warm forging was investigated.It is found that steel processed via warm forging improves comprehensive mechanical properties compared to the TWIP steel processed via cold rolling,with a high tensile strength(R_(m))of 793 MPa,a yield strength(R_(P))of 682 MPa,an extremely large R_(P)/R_(m)ratio as high as 0.86 as well as an excellent elongation rate of 46.8%.The microstructure observation demonstrates that steel processed by warm forging consists of large and elongated grains together with fine,equiaxed grains.Complicated micro-defect configurations were also observed within the steel,including dense dislocation networks and a few coarse deformation twins.As the plastic deformation proceeds,the densities of dislocations and deformation twins significantly increase.Moreover,a great number of slip lines could be observed in the elongated grains.These findings reveal that a much more dramatic interaction between microstructural defect and dislocations glide takes place in the forging sample,wherein the fine and equiaxed grains propagated dislocations more rapidly,together with initial defect configurations,are responsible for enhanced strength properties.Meanwhile,larger,elongated grains with more prevalently activated deformation twins result in high plasticity.
文摘Reasons for substution of Al and/or Si by P in TRIP steel were described.The details in thermodynamic and kinetic analyses and model parametre for the estimation,as well as the calculation results were listed.Low temperature tests were also shown to support the calculation result.Strengthening mechanism for different composition high Mn steels was discussed based on the optical micrograph,XRD,TEM and SEM measurements.It was therefore realized stack fault and its effect in phase transformation in high Mn steel was in the dependence of composition,strain and heat treatment.
