In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubric...In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubrication type.The experimental procedure of the rolling process is performed using the design of the experiment based on the Taguchi technique(L27),then surface roughness,surface hardness,and surface residual stresses are measured.The results showed that the lubrication density has a significant impact on the surface roughness which depends on the lubrication properties(mineral oil type,natural fat,and kinematic viscosity)while surface hardness and surface residual stresses were strongly affected by thickness reduction.On the other side,the augment in forming temperature can decrease the quality of the final surface finish and the surface hardness but reduce the induced residual stresses.The best surface finish is obtained based on the optimum condition of the rolling factors are(R%_(3),T_(1),andρ_(3))while the optimum condition of rolling parameters that generate higher hardness and compressive residual stresses are(R%_(3)T_(1)ρ_(1)).展开更多
In this research study,the mechanical properties of several Polymer matrix composites are investigated.These composites are multi-phase materials in which reinforcing materials are properly mixed with a polymer matrix...In this research study,the mechanical properties of several Polymer matrix composites are investigated.These composites are multi-phase materials in which reinforcing materials are properly mixed with a polymer matrix.More precisely,Nylon 6 reinforced with 5,15 and 25 wt.%of silicon carbide(SiC)and Nylon 6 reinforced with 5,15 and 25 wt.%of boron carbide(B_(4)C),prepared by means of an injection moulding process at three different injection pressures are considered.Specific attention is paid to the tensile and impact strength of these composites.The Taguchi technique is used to optimize the process parameters such as reinforcement material,its percentage and the injection pressure.It is observed that the specimens 5%SiC with 80 MPa injection pressure display a better tensile strength and similarly the specimen 5%B_(4)C with 90 MPa injection pressure have a superior impact strength.展开更多
文摘In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubrication type.The experimental procedure of the rolling process is performed using the design of the experiment based on the Taguchi technique(L27),then surface roughness,surface hardness,and surface residual stresses are measured.The results showed that the lubrication density has a significant impact on the surface roughness which depends on the lubrication properties(mineral oil type,natural fat,and kinematic viscosity)while surface hardness and surface residual stresses were strongly affected by thickness reduction.On the other side,the augment in forming temperature can decrease the quality of the final surface finish and the surface hardness but reduce the induced residual stresses.The best surface finish is obtained based on the optimum condition of the rolling factors are(R%_(3),T_(1),andρ_(3))while the optimum condition of rolling parameters that generate higher hardness and compressive residual stresses are(R%_(3)T_(1)ρ_(1)).
文摘In this research study,the mechanical properties of several Polymer matrix composites are investigated.These composites are multi-phase materials in which reinforcing materials are properly mixed with a polymer matrix.More precisely,Nylon 6 reinforced with 5,15 and 25 wt.%of silicon carbide(SiC)and Nylon 6 reinforced with 5,15 and 25 wt.%of boron carbide(B_(4)C),prepared by means of an injection moulding process at three different injection pressures are considered.Specific attention is paid to the tensile and impact strength of these composites.The Taguchi technique is used to optimize the process parameters such as reinforcement material,its percentage and the injection pressure.It is observed that the specimens 5%SiC with 80 MPa injection pressure display a better tensile strength and similarly the specimen 5%B_(4)C with 90 MPa injection pressure have a superior impact strength.
